Kohler 9459-BN Installation guide

Kohler
Brand
Kohler
Model
9459-BN
Type
Installation guide

This manual is also suitable for

1021774-2-B
K-9459
Sonata
R
Grab Bar And Acrylic Shelf
Installation Guide
Français, Page 5
Español, Página 8
1021774-2-B
1021774-2-B
2
Kohler Co.
Thank You For Choosing Kohler Company
We appreciate your choosing The Bold Look of Kohler with your
plumbing ware selection. Please take a moment to review this manual
before you start the installation. Contact us if you have any installation
or performance problems. Our phone numbers and website are listed
on the back cover. Thanks again for choosing Kohler Company.
Introduction
- Please read all instructions carefully to familiarize yourself with the
requir ed tools, materials and installation pr ocedur es.
- This document contains the latest product information available at the
time of publication. Kohler reserves the right to make changes in
product characteristics, packaging or availability at any time without
notice.
Recommended Tools and Materials
Hex
Wrench
Sealant
Open End
Box Wrench
Before You Begin
IMPORTANT: Access to the back of the module is required to install
the grab bar. The grab bar must be installed before the bath/shower
module is moved into place for installation.
1021774-2-B
3
Kohler Co.
Shelf
Screw
Bracket
Setscrew
Shower
Wall
Apply
Sealant
Wall Inserts
1. Shelf Installation
IMPORTANT: The wall inserts for the shelf brackets are installed in
the bath/shower wall at the factory.
- Apply a small amount of silicone sealant to the back of each bracket.
- Assemble the brackets and sockethead screws as shown.
- Use the hex wrench to install the bracket on the shower wall insert.
- Repeat for the other bracket.
- Remove any excess sealant from the brackets.
- Partially thread the setscrews into the brackets.
- Remove the prot ective paper backing from both sides of the shelf.
- Carefully slide the shelf into position in the bracket assembly recesses
and tighten the setscrews to secure the shelf to the brackets.
1021774-2-B
4
Kohler Co.
Nut
Large Washer
Shower Wall
Stud
Grab Bar
Lock Washer
Apply
Sealant
2. Grab Bar Installation
IMPORT
A
NT: Access to the bac
k
of the module is re
q
uired to install
the grab bar. The grab bar must be installed before the bath/shower
module is moved into place for installation.
- Carefully install the studs in the grab bar until the studs bottom in
handle. Back the studs out three turns. Failure to back the studs out
can cause damage to the grab bar surface.
- Apply a small amount of silicone sealant to each end of the grab bar
and install the grab bar through the shower wall.
- Apply a small amount of silicone sealant to the back of the large
washers. Install the washers over the grab bar studs.
CAUTION: Risk of product damage. Hold the stud in place with a
hex wrench when tightening the hex nut. If allowed to rotate, the stud
can dimple the grab bar surface.
- Apply a small amount of silicone sealant to the threads of the hex nuts
and studs. Install the large washers, lock washers and hex nuts on the
studs. Use a hex wrench to hold the stud in place while turning the hex
nuts to finger tight. While still holding the stud with the hex wrench,
tighten the hex nuts 1-1/4 more turns with the open end box wrench.
- Remove any excess sealant from the grab bar and the inside of the
shower module.
- Theshowermodulecannowbemovedintoplaceforinstallation.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Kohler 9459-BN Installation guide

Kohler
Brand
Kohler
Model
9459-BN
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents