Assa Abloy Norton Wave to Open 704 Installation guide

Brand: Assa Abloy

Model: Norton Wave to Open 704

Type: Installation guide

Assa Abloy Norton Wave to Open 704 is a switch that can be used to open doors with a simple hand wave. It has a detection range of up to 4 inches and can be mounted on door jambs between 34" and 48" from the floor. The switch has a built-in LED that flashes to indicate when the relay is active and a backup button for manual activation. It operates on 12V to 24VDC and has a time delay setting that can be adjusted from 1 to 35 seconds. The switch is easy to install and comes with all the necessary mounting hardware.

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9370-0002-020 Rev 2 07/20

Model 704 Wave to Open Switch

1-3/4" Wide Jamb Mounting

Installation Instructions

1/8"

Bit

Phillips

Drive Bit

Drill

Step

Bit

Flat Head

Screwdriver

Phillips Head

Screwdriver

Safety Glasses

Center

Punch

Pencil

Deburring

Tool

Wire Stripper/

Cutter

Tape Measure

This product can expose you to lead which is known to the state of

California to cause cancer and birth defects or other reproductive harm.

For more information go to www.P65warnings.ca.gov.

WARNING

Components Supplied Fasteners Tools Needed

Conduit supplied by others

This unit is not supplied with a radio frequency transmitter.

If a transmitter is added, a deeper surface mounted box,

supplied by others, will be needed.

M3 x 8.3mm Philips

Flat Head Machine

Screw

#8 Phillips Round

Head Metal

Drilling Screw

Conduit

Housing

Wave to Open

Switch

M3 Screw

#8 Screw

Specications:

Input Voltage: 12V to24VDC

SPDT Contact Rating: 2A @30VAC/VDC

Sensor Detection Range: Up to 4" (101mm)

Operating Temperature: -13° F to 131°F (-25°C to 55°C)

Current Draw: 50mA @12VDC, 65mA @24VDC

Approved 2020-07-09

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9370-0002-020 Rev 2 07/20

Model 704 Wave to Open Switch

Power

N/C

N/O

Power -

Wiring:

For proper wire connection, loosen

screws fully and ensure silver contact

is completely down. Insert wires and

tighten screws to secure wires.

1 Sec 5 Sec 10 Sec 15 Sec 20 Sec 25 Sec 30 Sec 35 Sec

LED Setting:

Time Delay Setting:

Jumper in place: LED is

Red and ashes Green

when relay is active.

No Jumper: LED is

Green and ashes Red

when relay is active.

31 "-/4

( mm)83

13 "-/4

( mm)44.5

15/16"

(24.2mm)

5/8"

(16mm)

1-3/8"

( mm)34.9

4-1/2"

(115mm)

1-3/ "4

( mm)44.5

Ø 78/"

( mm)22

Ø 316/"

( mm)5

( places)6

3- 11/16"

(94mm)

13 16/"

( mm)20

Wave to Open Switch Conduit Housing

Approved 2020-07-09

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9370-0002-020 Rev 2 07/20

Model 704 Wave to Open Switch

1. Place conduit housing on door jamb with

horizontal centerline between 34" - 48"

(86.4cm - 121.9cm) from oor. (Fig 1)

2. Using conduit housing as a template, mark

and center punch four (4) mounting holes and

conduit hole on door jamb.

3. Using 1/8" bit, drill four (4) mounting holes.

4. Using step drill, create a clearance hole for

conduit. Smooth conduit clearance hole with

deburring tool, if necessary.

Installation

Prepare Door Jamb

1. If required by local codes, attach wire conduit

(supplied by others) to back of housing and

feed wires through.

2. Align housing to mounting holes on door

jamb and secure with four (4) #8 Phillips

Round Head Metal Drilling screws. (Fig 3)

NOTE: Make sure housing is level.

Install Conduit Housing

1. Set LED and Time Delay Settings as desired on

Wave to Open switch. See “LED Setting” and

“Time Delay Setting”, page 2.

2. Use small at head screwdriver to connect

24VDC and activation wiring with terminal

block. (Fig 4) See “Wiring”, page 2 and

appropriate wiring diagram of door operator

instructions.

3. Attach Wave to Open switch to conduit

housing using two (2) M3 x 8.3mm Philips Flat

Head Machine screws. (Fig 5)

Install Switch

Terminal

Block

34" (86.4cm) Min

48" (121.9cm) Max

1-3/4"

(m)

44.5m

Figure 1

Figure 2

Figure 3

Figure 4 Figure 5

LED and

Timing

Delay

Approved 2020-07-09

Norton is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9370-0002-020 Rev 2 07/20

Norton Technical Product Support:

Monroe, NC 28112 USA

Phone: 800.438.1951 ext: 6030

TechSupport.Norton@assaabloy.com

nortondoorcontrols.com

Two Modes:

Standby (default LED Red)

Operating (default LED ashing Green)

To operate switch, make a slow waving

motion with hand in front of plate within

4" (101mm).

When hand movement is detected or

backup button is pressed, a tone will

sound and LED circle will ash to indicate

relay has been activated. (Fig 6)

Relay will activate for amount of time as

set by time delay jumpers. Backup button

can be used to activate relay at any time.

(Fig 6)

LED

Backup

Button

Operation

Figure 6

Approved 2020-07-09

Assa Abloy Norton Wave to Open 704 Installation guide

Assa Abloy Norton Wave to Open 704 Installation guide

Assa Abloy Norton Wave to Open 704 Installation guide

Related papers

Other documents