Aruba 9004 Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide
Aruba 9004-MNT-19 Kit
Installation Guide
0512128-03 | September 2019 1
This document provides installation instructions for mounting the 9004 gateway in a two-post
19-inch Telco rack. The rack mount tray supports installation of two 9004 gateway units.
Package Contents
Rack mount tray
Eight M3 x 5 mm flat head screws
Four M6 x 15 mm Phillips pan head screws
Four rubber clamps
Aruba 9004-MNT-19 Kit Installation Guide (this document, printed)
Rack Mount Installation
This mounting option allows mounting the 9004 gateway in a two-post 19-inch Telco rack.
Required Tools and Equipment
The following tools and equipment are required for installing a 9004 gateway:
Rack mount tray (x1) for rack mount installation
M3 x 5 mm flat head screws (x8) for securing the gateway on the rack mount tray
M6 x 15 mm Phillips pan head screws (x4) for rack mount
Suitable screwdrivers for all screw types provided in the box (not included in the kit)
Installation Steps
To install a 9004 gateway into a two post 19-inch rack:
1. Align the 9004 gateway to the screw hole provided on the rack mount tray.
2. Align the screws under the rack mount tray and tighten the screws to secure the 9004 gateway on
the rack mount tray. See Figure 1.
Some racks require screws that differ from those included with the 9004 gateway accessory kit. Ensure that
you have the correct screws before installing the 9004 gateway.
Ensure that the front panel of the 9004 gateway is facing towards the front side of the rack mount tray.
2 Aruba 9004-MNT-19 Kit | Installation Guide
Figure 1 Rack Mount Alignment
3. Use the rubber clamps provided with the kit to secure the power cable with the power adapter.
4. Pass one end of the rubber clamp through the DC cable of the adapter. Pass the power cable plug
through the other end of the rubber clamp before attaching it with the adapter. See Figure 2.
Figure 2 Attaching Rubber Clamp to the DC Power Adapter
5. Place the power adapter on the rack mount tray aligning it with the placement tabs provided. See
Figure 3.
Figure 3 Power Adapter Mounting
Aruba 9004-MNT-19 Kit | Installation Guide 3
6. Use the other rubber clamp provided with the mounting kit to secure the adapter on the rack
mount tray. Hook one end of the clamp into the left hook provided on the tray, pull the other end
and hook it to the right hook provided on the tray to secure the adapter completely. See Figure 4
and Figure 5.
Figure 4 Securing Power Adapter on the Tray
Figure 5 Securing Power Adapter on the Tray
7. Connect the DC power plug into the DC power connector provided on the back panel of the 9004
gateway.
8. Mount the rack mount tray within the two-post 19-inch rack using four M6 x 15 mm Phillips pan
head screws and a suitable screwdriver. See Figure 6.
4 Aruba 9004-MNT-19 Kit | Installation Guide
Figure 6 Rack Mount Installation
Rack mount installation of the 9004 gateway is now complete.
© 2019 Aruba, a Hewlett Packard Enterprise company All rights reserved.
www.arubanetworks.com
Hewlett Packard Enterprise Company
3333 Scott Boulevard
Santa Clara, California 95054
USA
Phone: 408.227.4500
Fax: 408.227.4550
5 Aruba 9004-MNT-19 Kit | Installation Guide
Contacting Support
Table 1 Contact Information
Main Site www.arubanetworks.com
Support Site http://support.arubanetworks.com
Airheads Social Forums and Knowledge
Base
www.community.arubanetworks.com
North American Telephone 1-800-943-4526 (Toll Free)
1-408-754-1200
International Telephones https://www.arubanetworks.com/support-services/contact-
support/
Software Licensing Site www.hpe.com/networking/support
End of Support information www.arubanetworks.com/support-services/end-of-life/end-of-life-
policy/
Security Incident Response Team (SIRT) Site: https://www.arubanetworks.com/support-services/security-
bulletins/
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Aruba 9004 Installation guide

Category
Wall & ceiling mounts accessories
Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI