Magnum RemusShield Finger Touch Immobilizer Installation Instructions Manual

Brand: Magnum

Model: RemusShield Finger Touch Immobilizer

Type: Installation Instructions Manual

Magnum RemusShield Finger Touch Immobilizer is an innovative security device that prevents unauthorized engine start by immobilizing the engine's critical components, such as the fuel pump, starter motor, or engine sensors. It features a unique touch sensor that requires the user's fingerprint to unlock the immobilizer, providing an additional layer of security. The device is easy to install and can be hidden in a discreet location, making it difficult for thieves to detect and disable.





RemusShield Finger Touch Immobilizer

INSTALLATION INSTRUCTIONS #55



Although the RemusShield finger touch immobilizer installs easy (DIY) and even people who are not technical minded will find that the kit is not

difficult to install, it is still an electronic device that affects engine operation and start, accordingly we strongly recommend having a certified

tech install this unit if you are still not technically inclined regarding this kind of wiring.

INSTALLATION

1. Connect the orange wire to the ignition-feed* +12V.

2. Connect the brown wire to the battery negative or engine frame.

3. Allocate which engine component you want to break, i.e. cranking motor, fuel pump, either engine sensor's signal wire**.

4. Cut the appropriate power cable of the electronic component selected and connect the RemusShield™'s two black wires.

inline with the two ends that just have been split. Find a hidden place for the sensor screws. Connect the black and white wire ends in

the ring terminal to the screws with the help of the nuts and washers provided in the package***.

5. Find a place for the head unit, service key, LED- and sound indicator****.

6. Connect the two male and female T-taps terminals of the service key. Leave the service key in normal mode. See picture.

7. Make sure the ignition key is switched off and finally connect the red cable to a constant battery +12V. Your immobilizer system is

alarmed, and the LED will be flashing.

NOTES

* Several engine components operate only when the ignition key is turned on. Use any ignition activated contact that is switched on and off

by the ignition key.

** Recommended ports to plug into, in order of relevance

 Engine sensor or engine management power wire in case of fuel injected models

 Fuel pump

 Starter motor

The less typical, the more creative, and unique your choice is, the less the chances are that thieves can steal your vehicle.

Establish firm connections in order to avoid engine shutdown. Make sure that the wire you tapped into doesn't transmit more than a 10 Amp

constant current. Over that current rate you will need to install relays.

*** You can fix the screws in any distance but it is recommended to mount them close to each other. Minimum distance is 0.04" - 1 mm. Any

closer positions might cause incidental blocks caused by water drops or moisture.

**** Dual sided adhesive tape can be stuck on the beeper to lower noise level. See picture.

Beeper is not waterproof!

WIRE COLOR RESPONSE

WIRE COLOR

CONTACT TO

NOTE

2 x BLACK

Engine-start blocking wire

choose any wire can break engine

start as

 electronic engine

management or engine

sensor if any

 fuel pump

 starting motor

No polarity

RED

constant battery +12V power

Make sure it supplies 20A current

ORANGE

ignition feed +12V power

select any contact is switched by

the ignition key

BROWN

-12V

battery negative or body

BLACK fitted with Ring terminal

sensor screw#1

Spade terminal side is grounded

WHITE fitted with Ring terminal

sensor screw#2

no polarity

BLUE fitted with male Spade terminal

RemusShield ™ 's blue wire fitted with female Spade terminal

GREEN fitted with male Spade terminal

RemusShield ™ 's green wire fitted with female Spade terminal

You may start the engine two different ways.

Scenario #1

1. Touch the sensor (short beep and LED shuts down)

2. Turn on the ignition key

3. You are now allowed to start the engine within 8 seconds. Engine will run as normally.

Scenario #2

1. Crank the engine

2. Touch the sensor within 20 seconds (beep and LED flash warns you that the engine block is retarded)

3. Engine will stop after 20 second lapsed

If for any reason you missed to unlock the immobilizer in the given timeframe, you need to wait another 10 seconds to be able to restart the

process unless the ignition key is turned off and on again. Since this occurrence reflects to unauthorized use, you will have less time to unlock

the system.

Service mode

It is highly recommended to activate service mode if your vehicle is taken to a wash, repair shop or wherever an unauthorized person can get

access to the location of your secret sensor. Don't divulge the location of your sensor to anyone you don't rely upon, just switch off the

RemusShield's service key. See switch positions and modes on the image below. In service mode the engine starts without touching the sensor as

normally, without the immobilizer.

In service mode the LED is flashing and a short beep sounds up after the engine starts, then the LED shuts down afterwards.

10-Year Warranty - for information please check out our terms and conditions on magnumtuning.com. .

Magnum RemusShield Finger Touch Immobilizer Installation Instructions Manual

Magnum RemusShield Finger Touch Immobilizer Installation Instructions Manual

Magnum RemusShield Finger Touch Immobilizer Installation Instructions Manual

Other documents