Westermo TD-33 DC User guide

Brand: Westermo

Model: TD-33 DC

Type: User guide

This manual is also suitable for

TD-33/V.90 DC

Tele Modem

V.90/K56flex™ or V.34

INSTALLATION MANUAL

6179-2204

www.westermo.se

TD33/V.90

TD-33

TD33/V.90 US

Westermo Teleindustri AB • 2001 • REV. A

Galvanic

Isolation

Transient

Protection

Balanced

Transmission

Approved

2 6179-2204

Table of Contents

Introduction

..................................................................................................................................................................... 3

Safety

.......................................................................................................................................................................................... 3

Specifications

.................................................................................................................................................................. 4

Installation

.......................................................................................................................................................................... 5

RS-232/V.24 Connections

........................................................................................................................... 5

LED Status Indicators

........................................................................................................................................ 5

Line Connection

........................................................................................................................................................ 6

Typical TD-33 Line Connections

.....................................................................................................

DIP Switch Setup

..................................................................................................................................................... 7

AT Commands

............................................................................................................................................... 8–21

Result Codes

................................................................................................................................................. 22–23

S-Registers

......................................................................................................................................................... 24–31

Glossary

................................................................................................................................................................ 32–34

Applications

................................................................................................................................................................. 35

36179-2204

Introduction

Congratulations for purchasing TD-33, probably the most robust modem device available on the market.

The TD-33 should not be confused with low-price replicas. You have just got a high quality product,

and with the excellent support from Westermo you will certainly not be unsatisfied with this product.

The Westermo TD-33 is an industrialised dial-up line modem. This modem has been developed to be

used in industrial applications and has some features one would not expect to find on a normal modem.

Terminal data rates of up to 115.2 kbit/s can be handled using data compression and error correction.

The maximum line modulation speed is 56.0 kbit/s (TD-33/V.90 ) or 33.6 kbit/s (TD-33 ).

A watchdog facility continually monitors the power supply and internal soft- and hardware. In the

event of a problem the modem automatically resets. This feature has been included to make the unit

more suitable for use in unmanned locations.

The TD-33 is available in two standard versions TD-33/V.90 including V.90 support and TD-33

containing up to V.34 support. The TD-33 is supplied by 12–36V DC.

The TD-33 has been designed with the engineer in mind, hence the extensive information on the

command set, S registers, DIP switches and error codes.

We have endeavoured to include all necessary information however if you need more please do not

hesitate to call us.

Safety

TD-33 and TD-33/V.90 comply with Directive 1999/5/EC.

The TD-33 shall only be connected to a power supply of type SELV.

Description of the above classifications are given in EN60950:1992

The TD-33 complies with EN-500081-1 & EN-500082-1

TD-33/V.90 US conforms to UL STD 1950 & CAN/CSA STD 22.2 No 950-95

Only Westermo TD-33/V90 US:

This equipment complies with Part 68 of the FCC Rules. On the outside of the package is a label that

contains, among other information, the FCC registration number for this equipment. If requested, pro-

vide this information to your telephone company. The registration jack for the equipment is RJ11C.

An FCC compliant telephone cord and modular plug is provided with this equipment. This equip-

ment is designed to be connected to the telephone network or premises wiring using a compatible

modular jack which is Part 68 compliant. See installation instructions for details.

The Ringer Equivalent, REN is useful to determine the number of devices that may be connected

to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in

response to an incoming call. In most, but not all areas, the sum of RENs of all devices should not

exceed five (5). To be certain of the number of devices that may be connected to a line, as determined

by the total RENs, contact the local telephone company.

If your telephone equipment TD-33/V.90 US causes harm to the telephone network, the telephone

company will notify you in advance that temporary discontinuance of service may be required. But if

advance notice isn’t practical, you will be notified as soon as possible. You will be advised of your

right to file a complaint with the FCC if you believe it is necessary.

Your telephone company may make changes in its facilities, equipment, operations, or procedures

that could affect the operation of your equipment. If they do, you will be given advance notice so as

to give you an opportunity to maintain uninterrupted service. If you experience trouble with this

equipment TD-33/V.90 US please contact U.S. Repair Center: MOTILE Address: 4345 B- Twain

Avenue, San Diego, CA 92120 Phone: 619-283-3325 for repair/warranty information. If your equip-

ment is causing harm to the telephone network, the telephone company may request that you discount

the equipment until problem is resolved.

This equipment may not be used on public coin service provided by the telephone company.

Connection to party lines is subject to state tariffs. (Contact your state public utility commission or

corporation commission for information). Since the modem not provides adequate protection against

electric shock shall it not be positioned in operator access area.

The line cord for connection to outside of telephone line shall be of AWG26 or larger.

4 6179-2204

Specifications

Modulation ITU-T V.90 28.0 up to 56.0 kbit/s

K56flex™, 32.0 up to 56.0 kbit/s

ITU-T V.34, 2.4 up to 33.6 kbit/s

ITU-T V.32bis, 4.8 up to 14.4 kbit/s

ITU-T V.32, 4 800/9 600 bit/s

ITU-T v.23, 1 200 bit/s

ITU-T V.22bis, 2 400 bit/s

ITU-T V.22, Bell 212A, 1 200 bit/s

ITU-T V.21, Bell 103, 300 bit/s

Dial up Tone signals DTMF

Settings AT-commands & switches

Transmission Asynchronous

Transmission speed, DTE 300, 600, 1 200, 2 400, 4 800, 7 200, 9 600, 12.0k, 14.4k,

16.8k, 19.2k, 21.6k, 24.0k, 26.4k, 28.8k, 38.4k, 57.6k &

115.2kbit/s

Compression V.42bis & MNP5

Characters Up to 11 bits

Error correction V.42 LAPM, MNP 2-4 & MNP 10

Interface EIA RS-232-C/V.24

Line interface RJ11

Line 2-wire for dial up connections

Power supply 12–36V DC

Power consumption 1.7 W at 12 V DC

Isolation Between line and rest of electronics 1500V

Fuse DC 1.0A

Temperature 0 to 60°C surrounding temperature

Humidity 0–95% RH, without condensation

Dimensions 55x100x128 mm (WxHxD)

Weight 0.2 kg

Indications TD, RD, DCD, DTR, RTS and PWR

Mounting On 35 mm DIN-rail

Misc. Password/Callback, DTR Hotcall, DIP-switches

56179-2204

Installation

The modem should be

connected in the following

way:

Power connection is made

through screw-block at

bottom right corner.

It is a 2-pole connector for

12–36 V DC supply.

Computers or other equip-

ment are connected through

an 9-pole D-sub RS-232/

V.24 connection.

Do not use ribbon cable

for RS-232 connections.

LED’s

Power supply

Screw-block

Only available in

TD-33/V90

9-pos

D-sub

RJ-11

Line

connection



TD-33

TEL.LINE

V24/RS-232-C

TD RD RTS DTR DCD PWR



TD-33

TD RD RTS DTR DCD PWR

1234567

▼

▼ ▼

▼

9-pos. Direction Description

D-sub DCE-DTE

1 DCD/Data carrier detect

2 RXD/Receive data

3 TXD/Transmit data

4 DTR/Data terminal ready

5 - - - SG/Signal ground

6 DSR/Data Set Ready

7 RTS/Request to send

8 CTS/Clear to send

9 RI/Ring indicator

Screw Description

terminal

1 SG/Signal Ground

2 DSR/Data Set Ready

3 DCD/Data Carrier Detect

4 DTR/Data Terminal Ready

5 CTS/Clear To Send

6 RTS/Request To Send

7 RXD/Receive Data

8 TXD/Transmit Data

9 SG/Signal Ground

RS-232/V.24 Connections

←

Pin outs for the 9-pole D-sub: TD-33/V.90, 9-pos screw terminal:

LED Status Indicators

PWR Power Indication. Flashes if an error is detected

DTR Data Terminal Ready modem signal

RTS Request To Send modem signal

TD Transmitted Data: Displays data received from the local RS-232/V.24 port

RD Received Data: Displays data leaving the modem on the RS-232/V.24 port

DCD Data Carrier Detect modem signal

6 6179-2204

TEL.LINE

Line connection

The telephone line is connected to the 2-pole RJ-11 connector.

2-wire lines are connected to the two middle pins (3 & 4) in

the RJ-11 plug.

Typical TD-33 line connections

RJ-11

plug

Telephone

Exchange

Telephone

Exchange

Dial up line 2-wire

76179-2204

Switch 1

Factory Settings

DIP Switch Setup for Dial-up

Disconnect power before changing DIP-switches.

The DIP-switches can be used to provide the following settings.

The DIP-Switches are underneath the top lid of the modem.

Non defined switches will be in off position.



TD-33

TEL.LINE

V24/RS-232-C

TD RD RTS DTR DCD PWR

S1:1-4

1234

9 600 bit/s, 8N1

1234

9 600 bit/s, 8E1

1234

9 600 bit/s, 8O1

1234

9 600 bit/s, 7N1

1234

9 600 bit/s, 7E1

1234

9 600 bit/s, 7O1

1234

19 200 bit/s, 8N1

1234

19 200 bit/s, 8E1

1234

19 200 bit/s, 8O1

1234

19 200 bit/s, 7N1

1234

19 200 bit/s, 7E1

1234

19 200 bit/s, 7O1

Auto Baud / Use saved format and speed

ESD

Use ESD-protection when changing switches.

8 6179-2204

AT Commands

A – Answer

The modem will go off-hook and attempt to answer an incoming call if correct conditions

are met. Upon successful completion of answer handshake, the modem will go on-line in

answer mode.

The modem will enter the connect state after exchanging carrier with the remote modem.

If no carrier is detected within a period specified in register S7, the modem hangs up.

Any character entered during the connect sequence will abort the connection attempt.

&An – Dial Abort Option

The modem normally aborts the connection negotiation if a character is received from

DTE during the connection phase. This command give the user the option to let the

modem ignore incoming characters.

&A0 Enables abort (Default)

&A1 Disables abort

Please also refer to AT&D

Bn – ITU-T or Bell

When the modem is configured to allow either option, the modem will select Bell or

CCITT modulation for a line speed connection of 300 or 1200 bps according to the

parameter supplied. Any other line speed will use a CCITT modulation standard. The

parameter value, if valid, is written to S27 bit 6.

B0 Selects CCITT operation at 300 or 1200 bps during Call Establishment and a

subsequent connection. (Default)

B1 Selects BELL operation at 300 or 1200 bps during Call Establishment and a

subsequent connection.

&Bn – DTR Dial Option

This command enables the modem to dial a number stored with &Zn=number when the

DTR signal goes from inactive to active signal level.

&B0 No automatic call with DTR. (Default)

&B1 Call on DTR.

Please also refer to AT&Z, AT&D

\Bn – Transmit Break to Remote

In non-error correction mode, the modem will transmit a break signal to the remote

modem with a length in multiples of 100 ms according to parameter specified.

If a number in excess of 9 is entered, 9 is used. The command works in conjunction

with the \K command. In error correction mode, the modem will signal a break through

the active error correction protocol, giving no indication of the length.

\B1-\B9 Break length in 100 ms units. (Default = 3.) (Non-error corrected mode only.)

96179-2204

&Cn – RLSD (DCD) Option

The modem controls the RLSD output in accordance with the parameter supplied.

The parameter value, if valid, is written to S21 bit 5.

&C0 RLSD remains ON at all times.

&C1 RLSD follows the state of the carrier. (Default)

%C – Enable/Disable Data Compression

Enables or disables data compression negotiation. The modem can only perform data

compression on an error corrected link.

The parameter value, if valid, is written to S41 bits 0 and 1.

%C0 Disables data compression. Resets S46 bit 1.

%C1 Enables MNP 5 data compression negotiation. Resets S46 bit 1.

%C2 Enables V.42 bis data compression. Sets S46 bit 1.

%C3 Enables both V.42 bis and MNP 5 data compression. Sets S46 bit 1. (Default)

Dn – Dial

This command directs the modem to go on-line, dial according to the string entered and

attempt to establish a connection. If no dial string is supplied, the modem will go on-line

and attempt the handshake in originate mode.

NOTE:

If the ATD command is issued before the S1 register has cleared, the modem will respond

with the NO CARRIER result code.

The modem will behave as a data modem and will attempt to connect to another data

modem. The modem will have up to the period of time specified by register S6 to wait for

carrier and complete the handshake. If this time expires before the modem can complete

the handshake, the modem will go on-hook with the NO CARRIER response.This com-

mand will be aborted in progress upon receipt of any DTE character before completion of

the handshake.

Dial Modifiers

The valid dial string parameters are described below. Punctuation characters may be used

for clarity, with parentheses, hyphen, and spaces being ignored.

The valid dial string parameters are described below. Punctuation characters may be used

for clarity, with parentheses, hyphen, and spaces being ignored.

0-9 DTMF digits 0 to 9.

* The ’star’ digit (tone dialing only).

# The ’gate’ digit (tone dialing only).

A-D DTMF digits A, B, C, and D. Some countries may prohibit sending of these

digits during dialing.

L Re-dial last number: the modem will re-dial the last valid telephone number.

The L must be immediately after the D with all the following characters

ignored).

R This command will be accepted, but not acted on.

S=n Dial the number stored in the directory (n = 0 to 1). (See &Z.)

! Flash: the modem will go on-hook for a time defined by the value of S29.

10 6179-2204

W Wait for dial tone: the modem will wait for dial tone before dialing the digits

following ”W“. If dial tone is not detected within the time specified by S6

(EU), the modem will abort the rest of the sequence, return on-hook, and gener-

ate an error message.

@ Wait for silence: the modem will wait for at least 5 seconds of silence in the

call progress frequency band before continuing with the next dial string param-

eter. If the modem does not detect these 5 seconds of silence before the expira-

tion of the call abort timer (S7), the modem will terminate the call attempt with

a NO ANSWER message. If busy detection is enabled, the modem may termi-

nate the call with the BUSY result code. If answer tone arrives during execu-

tion of this parameter, the modem handshakes.

& Wait for credit card dialing tone before continuing with the dial string. If the

tone is not detected within the time specified by S6 (EU models), the modem

will abort the rest of the sequence, return on-hook, and generate an error mes-

sage.

, Dial pause: the modem will pause for a time specified by S8 before dialing the

digits following ”,”.

; Return to command state. Added to the end of a dial string, this causes the

modem to return to the command state after it processes the portion of the dial

string preceding the ”;”. This allows the user to issue additional AT commands

while remaining off-hook. The additional AT commands may be placed in the

original command line following the ”;” and/or may be entered on subsequent

command lines. The modem will enter call progress only after an additional

dial command is issued without the ”;” terminator. Use ”H” to abort the dial in

progress, and go back on-hook.

^ Toggles calling tone enable/disable: applicable to current dial attempt only.

( ) Ignored: may be used to format the dial string.

- Ignored: may be used to format the dial string.

<space> Ignored: may be used to format the dial string.

<i> Invalid character: will be ignored.

&Dn – DTR Option

This command interprets the ON to OFF transition of the DTR signal from the DTE in

accordance with the parameter supplied. The parameter value, if valid, is written to S21

bits 3 and 4. Also, see S25.

&D0, DTR drop is interpreted according to the setting as follows: DTR is ignored

(assumed ON). Allows operation with DTEs which do not provide DTR.

(Default)

&D1 DTR drop is interpreted according to the setting as follows: DTR drop is inter-

preted by the modem as if the asynchronous escape sequence had been entered.

The modem returns to asynchronous command state without disconnecting.

&D2 DTR drop is interpreted according to the setting as follows: DTR drop causes the

modem to hang up. Auto-answer is inhibited.

&D3 DTR drop is interpreted according to the setting as follows: DTR drop causes the

modem to perform a soft reset as if the Z command were received. The &Y set-

ting determines which profile is loaded.

116179-2204

En – Command Echo

The modem enables or disables the echo of characters to the DTE according to the param-

eter supplied. The parameter value, if valid, is written to S14 bit 1.

E0 Disables command echo.

E1 Enables command echo. (Default)

%En – Enable/Disable Line Quality Monitor and Auto-

Retrain or Fallback/Fall Forward

Controls whether or not the modem will automatically monitor the line quality and request

a retrain (%E1) or fall back when line quality is insufficient or fall forward when line qual-

ity is sufficient (%E2). The parameter value, if valid, is written to S41 bits 2 and 6.

If enabled, the modem attempts to retrain for a maximum of 30 seconds.

%E0 Disable line quality monitor and auto-retrain.

%E1 Enable line quality monitor and auto-retrain.

%E2 Enable line quality monitor and fallback/fall forward. (Default)

Fallback/Fall Forward. When %E2 is active, the modem monitors the line quality (EQM).

When line quality is insufficient, the modem will initiate a rate renegotiation to a lower

speed within the V.34/V.32 bis/V.32 (TD-33) modulation speeds. The modem will keep

falling back within the current modulation if necessary until the speed reaches 2 400 bit/s

(V.34) or 4 800 bit/s (V.32). Below this rate, the modem will only do retrains if EQM

thresholds are exceeded. If the EQM is sufficient for at least one minute, the modem will

initiate a rate renegotiation to a higher speed within the current modulation speeds. The

rate renegotiations will be done without a retrain if a V.32 bis connection is established.

Speeds attempted during fallback/fall forward are those shown to be available in the rate

sequences exchanged during the initial connection. Fallback/fall forward is available in

error correction and normal modes, but not in direct mode.

&Fn – Restore Factory Configuration (Profile)

The modem loads the factory default configuration (profile). The factory defaults are

identified for each command and in the S-Register descriptions. A configuration (profile)

consists of a subset of S-Registers.

&F Restore factory configuration.

+GCI – Country Code

This selects the country code for the modem.

The command format is:

AT+GCI=<countrycode>

Where <countrycode> options are:

FD Europe (Default TD-33)

B5 North America (Default TD-33/V90 US)

For listing of the current configuration:

+GCI?

12 6179-2204

&Gn – Select Guard Tone

The modem generates the guard tone selected by this command according to the parame-

ter supplied (DPSK modulation modes only). The parameter value, if valid, is written to

S23 bits 6 and 7.

&G0 Disables guard tone. (Default).

&G1 Disables guard tone.

&G2 Selects 1 800 Hz guard tone.

This command may not be permitted in some countries.

*Gn – Password Enable/Disable

Controls whether or not the modem will handle Password and/or Callback functionality.

Value is written to S14 bit 6.

*G0 Disables Password handling. (Default).

*G1 Enable Password handling.

See also *Pn and *L.

Hn – Disconnect (Hang-Up)

This command initiates a hang up sequence.

H0 The modem will release the line if the modem is currently on-line. Country

specific, modulation specific, and error correction protocol specific (S38)

processing is handled outside of the H0 command.

H1 If on-hook, the modem will go off-hook and enter command mode.For EU models,

the modem will return on-hook after a period of time determined by S7.

\Kn – Break Control

Controls the response of the modem to a break received from the DTE or the remote

modem or the \B command according to the parameter supplied. The parameter value, if

valid, is written to S40 bits 3, 4, and 5.

The response is different in three separate states.

The first state is where the modem receives a break from the DTE when the modem is

operating in data transfer mode:

\K0 Enter on-line command mode, no break sent to the remote modem.

\K1 Clear data buffers and send break to remote modem.

\K2 Same as 0.

\K3 Send break to remote modem immediately.

\K4 Same as 0.

\K5 Send break to remote modem in sequence with transmitted data. (Default)

The second case is where the modem is in the on-line command state

(waiting for AT commands) during a data connection,

and the \B is received in order to send a break to the remote modem:

\K0 Clear data buffers and send break to remote modem.

\K1 Clear data buffers and send break to remote modem. (Same as 0.)

\K2 Send break to remote modem immediately.

\K3 Send break to remote modem immediately. (Same as 2.)

\K4 Send break to remote modem in sequence with data.

136179-2204

\K5 Send break to remote modem in sequence with data. (Same as 4.) (Default)

The third case is where a break is received from a remote modem during a non-error

corrected connection:

\K0 Clears data buffers and sends break to the DTE.

\K1 Clears data buffers and sends break to the DTE. (Same as 0.)

\K2 Send a break immediately to DTE.

\K3 Send a break immediately to DTE. (Same as 2.)

\K4 Send a break in sequence with received data to DTE.

\K5 Send a break in sequence with received data to DTE. (Same as 4.) (Default)

&K – Flow Control

Defines the DTE/DCE Flow Control. The parameter is written to S39 bits 0,1, and 2.

&K0 Disables flow control (Default).

&K3 Enables RTS/CTS.

&K4 Enables XON/XOFF.

&K5 Enables transparent XON/XOFF.

-Kn – MNP Extended Services

Enables or disables conversion of a V.42 LAPM connection to an MNP 10 connection.

The parameter value, if valid, is written to S40 bits 0 and 1.

-K0 Disables V.42 LAPM to MNP 10 conversion. (Default)

-K1 Enables V.42 LAPM to MNP 10 conversion.

-K2 Enables V.42 LAPM to MNP 10 conversion; inhibits MNP Extended Services initi-

ation during V.42 LAPM answer mode detection phase.

%L – Report Line Signal Level

Returns a value which indicates the received signal level. The value returned is a direct

indication of the receive level at the MDP, not at the telephone line connector. For

example, 009 = –9 dBm, 043 = –43 dBm, and so on.

L – Speaker Volume

Sets the speaker volume control. The parameter is written to S22 bits 0 and 1.

L0 Low Volume

L1 Low Volume (Default)

L2 Medium Volume.

L3 High Volume.

*L – Display Stored Passwords and Callback numbers

This commands displays stored Password and Callback numbers.

14 6179-2204

M – Speaker Control

Speaker Control command. The parameter is written to S22 bits 2 and 3.

M0 Speaker is always off

M1 Speaker is on during call estabilishment, but off when receiving a carrier. (Default)

M2 Speaker is always on.

M3 Speaker is off when receiving a carrier and during dialing, but on during answering.

+MS – Select Modulation

This extended-format command selects the modulation and, optionally, enables or disables

automode, specifies the lowest and highest receive rates, and, specifies the highest trans-

mit rate using one to six subparameters. The command format is:

+MS=<carrier>,<automode>,<min_tx_rate>,<max_tx_rate>,<min_rx_rate>,<max_rx_rate>

Where: <carrier> = A string which specifies the preferred modulation (automode enabled)

or the modulation (automode disabled) to use in originating or answering a connection.

The options are:

<carrier> Modulation Possible Rates (bit/s)

V21 V.21 300

V22 V.22 1 200

V22B V.22 bis 2 400 or 1 200

V23C V.23 1 200

V32 V.32 9 600 or 4 800

V32B V.32 bis 14 400, 12 000, 9 600, 7 200, or 4 800

V34 V.34 33 600, 31 200, 28 800, 26 400, 24 000, 21 600, 19 200, 16 800, 14 400,

12 000, 9 600, 7 200, 4 800, or 2 400

V90 V.90 56 000, 54 667, 53 333, 52 000, 50 667, 49 333, 48 000, 46 667, 45 333,

42 667, 41 333, 40 000, 38 667, 37 333, 36 000, 34 667, 33 333, 32 000, 30 667,

29 333, 28 000

B103 Bell 103 300

B212 Bell 212 1 200

0 disable

1 enable

<min_xx_rate>, <max_xx_rate>

Min and max data rates depending on modulation used (see below).

Reporting Supported Options

The modem can send a string of information to the DTE consisting of supported options

using the following command:

+MS=?

For listing current configuration:

+MS?

156179-2204

\Nn – Operating Mode

This command controls the preferred error correcting mode to be negotiated in a

subsequent data connection.

\N0 Selects normal speed buffered mode (disables error-correction mode). (Forces &Q6.)

\N1 Serial interface selected – Selects direct mode and is equivalent to &Q0 mode of

operation. (Forces &Q0.)

\N2 Selects reliable (error-correction) mode. The modem will first attempt a LAPM

connection and then an MNP connection. Failure to make a reliable connection

results in the modem hanging up. (Forces &Q5, S36=4, and S48=7.)

\N3 Selects auto reliable mode. This operates the same as \N2 except failure to make a

reliable connection results in the modem falling back to the speed buffered normal

mode. (Forces &Q5, S36=7, and S48=7.)

\N4 Selects LAPM error-correction mode. Failure to make an LAPM error-correction

connection results in the modem hanging up. (Forces &Q5 and S48=0.) Note: The

-K1 command can override the \N4 command.

\N5 Selects MNP error-correction mode. Failure to make an MNP error-correction con-

nection results in the modem hanging up. (Forces &Q5, S36=4, and S48=128.)

On – Return to On-Line Data Mode

This command determines how the modem will enter the on-line data mode. If the modem

is in the on-line command mode, it enters the on-line data mode with or without a retrain.

If the modem is in the off-line command mode (no connection), ERROR is reported.

O0 Enters on-line data mode without a retrain. Handling is determined by the Call

Establishment task.Generally, if a connection exists, this command connects the

DTE back to the remote modem after an escape (+++).

O1 Enters on-line data mode with a retrain before returning to on-line data mode.

*Pn – Store Password and Callback number

It is possible to store 2 different Passwords and Callback numbers in the modem.

This command works if command *G1 is used.

The command format is:

*P0:Password#0:Callbacknumber#0

*P1:Password#1:Callbacknumber#1

Password min. 6 characters max. 12 characters.

Callback number up to 18 characters.

If Password and Callback number is stored then the modem prompts the text ”PASSWORD:”

before releasing the connection and dialing back after a time given in S13.

If target is busy three retries will be executed.

If no Callback number is stored then the modem prompts the text ”PASSWORD:”

before switching into normal data transmission mode.

If no Password is stored then the modem prompts ”CALLBACK NUMBER:” before releasing

the connection and dialing back after a time given in S13.

16 6179-2204

Qn – Quiet Results Codes Control

The command enables or disables the sending of result codes to the DTE according to the

parameter supplied. The parameter value, if valid, is written to S14 bit 2.

Q0 Enables result codes to the DTE. (Default)

Q1 Disables result codes to the DTE.

&Q – Async Mode

This command is used to control the connection modes permitted. It is used in conjunc-

tion with S36 and S48. (Also, see \N).

&Q0 Selects direct asynchronous operation. The value 000b is written to S27 bits 3, 1,

and 0, respectively.

&Q5 The modem will try to negotiate an error-corrected link. The modem can be con-

figured using S36 to determine whether a failure will result in the modem return-

ing on hook or will result in fallback to an asynchronous connection. The value

101b is written to S27 bits 3, 1 and 0 respectively (Default).

&Q6 Selects asynchronous operation in normal mode (speed buffering). The value

110b is written to S27 bits 3, 1 and 0, respectively.

%Q – Report Line Signal Quality

Reports the line signal quality. Returns the higher order byte of the EQM value. Based on

the EQM value, retrain or fallback/fall forward may be initiated if enabled by %E1 or %E2.

&Sn – DSR Override

This command selects how the modem will control DSR. The parameter value, if valid, is

written to S21 bit 6.

&S0 DSR will remain ON at all times. (Default)

&S1 DSR will become active after answer tone has been detected and inactive after the

carrier has been lost.

%Un – Select µ-Law or A-Law Codec Type

This command selects µ-Law or A-Law codec type for V.90 and K56flex modulation.

This command also stores the selected setting directly to NVRAM.

%U0 Selects µ-Law.

%U1 Selects A-Law.

Vn – Result Code Form

This command selects the sending of short-form or long-form result codes to the DTE.

The parameter, if valid, is written to S14 bit 3.

V0 Enables short-form (terse) result codes. Line feed is not issued before a short-form

result code.

V1 Enables long-form (verbose) result codes. (Default)

176179-2204

\Vn – Single Line Connect Message Enable

This command enables or disables the single line connect message format as follows:

\V0 Connect messages are controlled by the command settings X, W, and S95.

(Default)

\V1 Connect messages are displayed in the single line format described below subject

to the command settings V (Verbose) and Q (Quiet). In Non-Verbose mode (V0),

single line connect messages are disabled and a single numeric result code is gen-

erated for CONNECT DTE.

When single line connect messages are enabled, there are no CARRIER, PROTOCOL,

or COMPRESSION messages apart from the fields described below.

The single line connect message format is:

CONNECT

<DTE Speed></Modulation></Protocol></Compression></Line

Speed>/<Voice and Data>

Where:

<DTE Speed> = DTE speed, e.g., 57 600.

Modulation = “V90” for V.90 modulation.

“K56” for K56flex modulation.

“V34” for V.34 modulation.

“V32” for V.32 or V.32bis modulation.

Note: Modulation is omitted for all other modulations.

Protocol = “NONE” for no protocol.

“ALT” for Microcom Network Protocol.

“LAPM” for LAP-M protocol.

Compression = “CLASS5” for Microcom MNP5 compression.

“V42BIS” for V.42bis compression.

Note: Compression is omitted if protocol is NONE.

Line Speed = Asymmetric rates are displayed as /rate:TX/rate:RX, e.g., /1 200

TX/75 RX.

Symmetric rates are displayed as a single DCE rate, e.g., 14 400.

Voice and Data = Blank for Data mode only.

LAPM-SREJ = Selective reject.

18 6179-2204

&V – Display Current Configuration and Stored Profiles

&V – Display Current Configuration and Stored Profiles Reports the current (active) con-

figuration, the stored (user) profiles, and the first four stored telephone numbers. The

stored profiles and telephone numbers are not displayed if the NVRAM is not operational

as detected by the NVRAM test during reset processing.

Example:

AT&V

ACTIVE PROFILE:

B0 E1 L1 M1 N1 QO T V1 W0 X4 Y0 &C0 &D0 &G2 &K0 &Q5 &R1 &S0 &T4

&X0 &Y0 S00:002 S01:000 S02:043 S03:013 S04:010 S05:008 S06:002 S07:030

S08:002 S09:006 S10:014 S11:255 S12:050 S18:000 S25:005 S26:001 S36:007

S37:000 S38:020 S46:138 S48:007 S95:000

STORED PROFILE 0:

B0 E1 L1 M1 N1 QO T V1 W0 X4 Y0 &C0 &D0 &G2 &K3 &Q5 &R1 &S0 &T4

&X0 S00:002 S02:043 S06:002 S07:030 S08:002 S09:006 S10:014 S11:095 S12:050

S18:000 S36:007 S37:000 S40:105 S41:003 S46:138 S95:000

STORED PROFILE 1:

B0 E1 L1 M1 N1 QO T V1 W0 X4 Y0 &C0 &D0 &G2 &K3 &Q5 &R1 &S0 &T4

&X0 S00:002 S02:043 S06:002 S07:030 S08:002 S09:006 S10:014 S11:095 S12:050

S18:000 S36:007 S37:000 S40:105 S41:003 S46:138 S95:000

TELEPHONE NUMBERS:

0 = 1 =

196179-2204

&V1 – Display Last Connection Statistics

Displays the last connection statistics in the following format (shown with typical results):

TERMINATION REASON.......... LOCAL REQUEST

LAST TX rate................ 26 400 BIT/S

HIGHEST TX rate............. 26 400 BIT/S

LAST RX rate................ 46 667 BIT/S

HIGHEST RX rate............. 46 667 BIT/S

PROTOCOL.................... LAPM

COMPRESSION................. V42Bis

Line QUALITY................ 033

Rx LEVEL.................... 015

Highest Rx State............ 67

Highest TX State............ 67

EQM Sum..................... 00C2

RBS Pattern................. FF

Rate Drop................... FF

Digital Pad................. None

Local Rtrn Count............ 00

Remote Rtrn Count........... 00

Flex 9481814347C4

RBS Pattern: Shows the number of least significant bits robbed per 6 bytes.

Digital Pad: Shows if a pad was encountered and if so, what was the digital loss.

Flex: Shows V.8bis information as follows:

First byte: Octect 13 (second byte of manufacturer id, 94 = K56flex)

Second byte: Octect 14 (Licensee code: 81 = Rockwell)

Third byte: Octect 15 (manufacturer's product capabilities)

Fourth byte: Octet 16 (K56flex version number)

Fifth byte: Octet 17 (Rockwell pump code version number)

Sixth byte: Octet 18 (x-law and controller version number)

Bit 6 Forced/Not forced A-Law/µ-Law

0 = Forced A-Law/µ-Law

1 = Not forced A-Law/µ-Law

Bit 5 Select A-Law or µ-Law

0 = Select A-Law

1 = Select µ-Law

Bit 4:0 Controller version

Wn – Connect Message Control

This command controls the format of CONNECT messages. The parameter value, if valid,

is written to S31 bits 2 and 3.

W0 Upon connection, the modem reports only the DTE speed (e.g., CONNECT

19 200). Subsequent responses are disabled. (Default)

W1 Upon connection, the modem reports the line speed, the error correction protocol,

and the DTE speed, respectively. Subsequent responses are disabled.

W2 Upon connection, the modem reports the DCE speed (e.g., CONNECT 14 400).

Subsequent responses are disabled.

20 6179-2204

&Wn – Store Current Configuration

Saves the current (active) configuration (profile), including S-Registers, in one of the two

user profiles in NVRAM as denoted by the parameter value. This command will yield an

ERROR message if the NVRAM is not operational as detected by the NVRAM test.

The current configuration is comprised of a list of storable parameters illustrated in the

&V command. These settings are restored to the active configuration upon receiving an

Zn command or at power up (see &Yn command).

&W0 Store the current configuration as profile 0.

&W1 Store the current configuration as profile 1.

Xn – Extended Result Codes

This command selects which subset of the result messages will be used by the modem to

inform the DTE of the results of commands.

Blind dialing is enabled or disabled by country parameters. If the user wishes to enforce

dial tone detection, a "W" can be placed in the dial string (see D command). Note that the

information below is based upon the default implementation of the X results table.

X0 Disables monitoring of busy tones unless forced otherwise by country requirements;

send only OK, CONNECT, RING, NO CARRIER, ERROR, and NO ANSWER

result codes. Blind dialing is enabled/disabled by country parameters. If busy tone

detection is enforced and busy tone is detected, NO CARRIER will be reported. If

dial tone detection is enforced or selected and dial tone is not detected, NO

CARRIER will be reported instead of NO DIAL TONE. The value 000b is

written to S22 bits 6, 5, and 4, respectively.

X1 Disables monitoring of busy tones unless forced otherwise by country requirements;

send only OK, CONNECT, RING, NO CARRIER, ERROR, NO ANSWER, and

CONNECT XXXX (XXXX = rate). Blind dialing enabled/disabled by country

parameters. If busy tone detection is enforced and busy tone is detected, NO

CARRIER will be reported instead of BUSY. If dial tone detection is enforced or

selected and dial tone is not detected, NO CARRIER will be reported instead of

NO DIAL TONE. The value 100b is written to S22 bits 6, 5, and 4, respectively.

X2 Disables monitoring of busy tones unless forced otherwise by country requirements;

send only OK, CONNECT, RING, NO CARRIER, ERROR, NO DIALTONE, NO

ANSWER, and CONNECT XXXX. If busy tone detection is enforced and busy

tone is detected, NO CARRIER will be reported instead of BUSY. If dial tone

detection is enforced or selected and dial tone is not detected, NO DIAL TONE will

be reported instead of NO CARRIER. The value 101b is written to S22 bits 6, 5,

and 4, respectively.

X3 Enables monitoring of busy tones; send only OK, CONNECT, RING, NO CARRI-

ER, ERROR, NO ANSWER, and CONNECT XXXX. Blind dialing is enabled/dis-

abled by country parameters. If dial tone detection is enforced and dial tone is not

detected, NO CARRIER will be reported. The value 110b is written to S22 bits 6,

5, and 4, respectively.

X4 Enables monitoring of busy tones; send all messages. The value 111b is written to

S22 bits 6, 5, and 4, respectively. (Default)

Page is loading ...

Westermo TD-33 DC User guide

Brand: Westermo

Model: TD-33 DC

Type: User guide

This manual is also suitable for

TD-33/V.90 DC

Download PDF

report

Westermo TD-33 DC User guide

This manual is also suitable for

Westermo TD-33 DC User guide

Related papers

Other documents