Homder Upgrade Dash Cam Front and Rear, 7'' Monitor Front Lens User manual

Brand: Homder

Model: Upgrade Dash Cam Front and Rear, 7'' Monitor Front Lens

Category: Drive recorders

Type: User manual

Front and Rear Dual Lens Truck Dash Cam Kit

User Manual

Preface

Thank you for purchasing our products.

This manual will detail how to install, operate, product parameter and matters needing

attention. Please read carefully and please safe keeping before use, we hope that our

products can meet your needs and long-term service to you! But because

the specifications may be due to upgrade,update and other reasons do change, refer to the

actual product, without prior notice. The manufacturer reserves without prior notice, to

change the technology of direct rights.

Please note that this product is for personal use only, its method of use shall not

commit domestic or international copyright / privacy laws. That image is for personal use

only recorded, not foreign free to publish spread; in addition to using this

product recorded performances, exhibitions or commercial activities of the image may in

some cases infringe copyright or the legal rights and interests.

Wiring Guide

1. Attach the truck dash cam to the bracket and fix it in the position to be installed.

2. Install the rear view camera on the back of the vehicle and pay attention to the direction when

installing. Wiring can be routed along the roof of the vehicle. After the installation is complete,

plug the plug into the rear camera interface of the recorder.

3. Adjust the lens position of the rear view camera to a suitable angle

4. Start the vehicle engine and check if the product is installed correctly.

Menu Settings

1.Video camera settings

Press the power button to boot , in video camera mode by pressing "MENU" button for 2 second

to enter the menu setting mode

Menu option:

1.1 The video resolution settings : 1080FHD 1920 * 1080, 1080P 1440* 1080, 720P 1280 * 720

three options.

1.2. Loop recording : Off / 1 minutes / 2 minutes / 3 minutes

Close : Close the loop recording, when the card is full stop recording

1 minutes : Each video files longest recording time of 1 minute

2 minutes : Each video files longest recording time of 2 minutes

3 minutes : Each video files longest recording time is 3minutes

1.3 Exposure : Underexposed , dim the screen , you need to fill light

1.4 Motion Detection : closed and open . When you select "Open ", press "OK" button to confirm ,

press MENU key to exit , start motion detection, if an object moves, the machine will

automatically start recording at this time , no object moves, the machine is in motion detection

standby mode, when an object moves, and start recording.

Press the "OK" button to confirm the selection is good , the setting is completed, press the

"MENU" to exit mode

2.Camera settings

Press the "POWER" key to boot, in the video camera mode by pressing "MENU" button to enter

the camera mode , Press "MENU" button for 2 second to enter the menu setting mode.

2.1 Resolution : 1920 * 1080, 1280 * 720, 640 * 480 three options.

2.2 Sequence : closed and open

2.3 Picture Quality : Fine / Normal / Economy

2.4 Sharpness : Strong / Normal / Soft

2.5 White Balance : Auto / 100 /200

2.6 ISO : Camera sensitivity

2.7 Exposure : Underexposed , dim the picture , you need to fill light

2.8 Quick Review : Quickly view stored images

2.9 Date stamp : Off / Date / Date and Time

Off: Video files will not display the current time watermark

Date : lower left corner of the video files have a watermark date displays the current time

Date and Time : lower left corner of the video files have a watermark date and time displays the

current time

Press the "OK" button to confirm the selection is good , the setting is completed, press the

"MENU" to exit mode

3.Playback Settings

Press the "POWER" key to boot, in video camera mode, press the "MENU" button three times to

enter the playback mode , Press"MENU" button for a long time to enter the menu setting mode

3.1 File Delete: Delete the current , remove all

Delete the current : Delete the current file

Delete All : Delete all the files

3.2 Protect : lock protection leaflets protect all locked , unlock protection leaflets unlock protect

all

Single lock protection : protection can be locked to each video file

All lock protection : can be locked to protect against all video files

Unlock protection leaflet : can be unlocked for each video file

Unlock the protection of all : You can unlock all video files

Press the "OK" button to confirm the selection is good , the setting is completed, press the

"MENU" to exit mode

4.System Settings

Press the "POWER" key to boot, in video camera mode by pressing "MENU" button for 2 second

to enter the menu setting mode , and then through the "MENU" button ( Camera Settings /

System Settings ) , select System Settings Press "OK" button to confirm.

4.1 Date/Time : Press "OK", you can in year / month / day / hour / minute / s to switch between

each other , by a short press " up key" or "down key" need to adjust the value, press "OK" to

confirm the changes ;

4.2 Ruler Setting: Turn on/ off guideline

4.3 Auto power off : Close , 1 minute , 3 minutes

Off: does not automatically shut down when the standby

1 minutes : standby status 1 minute automatic shutdown

3 minutes : standby status 3 minutes automatic shutdown

5 minutes : when idle for 5 minutes automatic shutdown

4.4 Screen Saver : Close, 3 minute , 5 minutes ,10 minutes

4.5 Language: English, Simplified Chinese, Traditional Chinese, Spanish. French, Portuguese ,

Russian , German, Japanese, Korean, Polish.

4.6 Format : Cancel / OK

Cancel: Cancels the current settings

OK : the TF card format

4.7 Default Setting : Cancel / OK

4.8 Version : Product version information

By "DOWN / UP" Select Settings , then press "OK" button to confirm , to complete the setting ,

press "MENU" to exit the mode, the exit mode, press the "POWER" button to shutdown , reboot

after setting success.

Operation function introduction

1. Use automatic recording

When the car is started, the recorder automatically starts up and turns on the recording function

(the automatic recording function is turned on). The recorded image is segmented and saved on

the TF card. When the TF card is full, the recorder covers the image recorded before the focus.

The front/rear cameras are stored in the "DCIMA" and "DCIMB" folders of the TF card,

respectively.

2. Use motion detection

In the standby state, press the button for three seconds to enter the motion detection mode.

When the lens senses that there is a moving object around, the machine enters the camera state.

When the lens does not detect the object moving for 5 seconds, the system stops recording.

Press and hold the up button for three seconds to exit the motion detection mode.

3.Gravity sensor function（G-sensor）

When the gravity acceleration starts, the machine will automatically save the video when the

accident occurred was not delete the file.

Gravity sensor can be adjusted in the menu high - medium - low , medium factory default .

4.File locking feature

The imaging process, the MENU button is pressed , The machine will lock the image in the first 10

seconds and the last 20 seconds.

Troubleshooting

Under normal operating conditions, such as abnormal products , please refer to the solution :

Unable to boot :

Check the recorder and power cable connected correctly. As a result of procedural questions

by pressing the RESET Reset button to restore to factory settings.

When the camera automatically stops recording, or do not cycle the camera :

Due to the huge high-definition video data , it is possible because the memory card reader could

not keep pace . Please use the high-speed TF card , such as C10 high-speed card.

Not cycle the camera is also possible that gravity sensor opens , the memory card are all locked

files causing . Please gravity sensor is closed, and the memory card is formatted .

Each time the camera and set the cycle is not the same :

Check to see if motion detection function, because the camera motion detection state length of

time, depending on the screen there is no movement.

Shoot the movie is not clear :

Please check whether the stolen camera , finger print . Please clean the lens before shooting the

surface , keep the lens clean .

Sometimes when the effect of the film shoot bad thing :

Camera effects and lighting conditions to shoot a great relationship , such as back lighting , shun

the light , the intensity of light , and this will result in different shooting out of the video.

Warranty Card

Buyer Name

Phone Number

Return Address

Item Reference[SKU]

Order Number

Problem Details

We offer one-year warranty and lifetime technical support for the products we have

sold.

Please kindly fill this warranty card once you got item and keep it well,since it need

to be send back together with the item when warranty active.

Homder Upgrade Dash Cam Front and Rear, 7'' Monitor Front Lens User manual

Brand: Homder

Model: Upgrade Dash Cam Front and Rear, 7'' Monitor Front Lens

Category: Drive recorders

Type: User manual

Download PDF

report

Homder Upgrade Dash Cam Front and Rear, 7'' Monitor Front Lens User manual

Homder Upgrade Dash Cam Front and Rear, 7'' Monitor Front Lens User manual

Other documents