Prime-Line F 2755 Operating instructions

Brand
Prime-Line
Model
F 2755
Type
Operating instructions

Prime-Line F 2755 is a window latch and keeper set that can be used to replace or repair existing latches and keepers on windows. The set includes a latch and a keeper, both of which are made of durable materials. To mount the latch, you can either use the existing holes in the window frame or drill new holes. The keeper must be aligned with the latch and can be pre-drilled if necessary. The latch can be set to a locked position, and the keeper can be aligned with the cam. The set comes with all the necessary hardware for installation.

Prime-Line F 2755 is a window latch and keeper set that can be used to replace or repair existing latches and keepers on windows. The set includes a latch and a keeper, both of which are made of durable materials. To mount the latch, you can either use the existing holes in the window frame or drill new holes. The keeper must be aligned with the latch and can be pre-drilled if necessary. The latch can be set to a locked position, and the keeper can be aligned with the cam. The set comes with all the necessary hardware for installation.

F 2755 F 2755 F 2755 F 2755 F 2755
Tools needed / Herramientas necesarias / Outils requis Tools needed / Herramientas necesarias / Outils requis Tools needed / Herramientas necesarias / Outils requis Tools needed / Herramientas necesarias / Outils requis Tools needed / Herramientas necesarias / Outils requis
3/32" - 2 mm 3/32" - 2 mm 3/32" - 2 mm 3/32" - 2 mm 3/32" - 2 mm
2-1/16"
5.2 cm
2-1/16"
5.2 cm
2-1/16"
5.2 cm
2-1/16"
5.2 cm
2-1/16"
5.2 cm
9/16" / 14 mm 9/16" / 14 mm 9/16" / 14 mm 9/16" / 14 mm 9/16" / 14 mm
7/16"
11 mm
7/16"
11 mm
7/16"
11 mm
7/16"
11 mm
7/16"
11 mm
1"
2.5 cm
1"
2.5 cm
1"
2.5 cm
1"
2.5 cm
1"
2.5 cm
1-1/16"
2.7 cm
1-1/16"
2.7 cm
1-1/16"
2.7 cm
1-1/16"
2.7 cm
1-1/16"
2.7 cm
Check new latch and keeper for proper alignment and hole
spacings on window frame. Mount latch (1) in existing holes
or mark new location and pre-drill 3/32" new holes. Install
and set to locked position. Align keeper (2) with cam, pre-drill
holes (if needed) and install.
Compruebe nueva pestillo y retén de alineación y los orificios
espaciados adecuados en marco de la ventana. Monte el
cerrojo (1) en los orificios existentes o marque la nueva
ubicación y taladre orificios nuevos de 3/32". Instale mueva
el cerrojo a la posición de cerrado. Alinee la sujetador (2) con
leva, taladre los orificios (si es necesario) e instale.
Vérifiez nouvelle loquet et verrou de l'alignement et de trous
espacements appropriés sur châssis de fenêtre. Installez le
loquet (1) dans les orifices existant ou marquez la nouvelle
position et percez des orifices de 3/32". Installez et réglez
à la position verrouillée. Alignez le cliquet (2) sous la came,
percez les orifices et installez.
Check new latch and keeper for proper alignment and hole
spacings on window frame. Mount latch (1) in existing holes
or mark new location and pre-drill 3/32" new holes. Install
and set to locked position. Align keeper (2) with cam, pre-drill
holes (if needed) and install.
Compruebe nueva pestillo y retén de alineación y los orificios
espaciados adecuados en marco de la ventana. Monte el
cerrojo (1) en los orificios existentes o marque la nueva
ubicación y taladre orificios nuevos de 3/32". Instale mueva
el cerrojo a la posición de cerrado. Alinee la sujetador (2) con
leva, taladre los orificios (si es necesario) e instale.
Vérifiez nouvelle loquet et verrou de l'alignement et de trous
espacements appropriés sur châssis de fenêtre. Installez le
loquet (1) dans les orifices existant ou marquez la nouvelle
position et percez des orifices de 3/32". Installez et réglez
à la position verrouillée. Alignez le cliquet (2) sous la came,
percez les orifices et installez.
Check new latch and keeper for proper alignment and hole
spacings on window frame. Mount latch (1) in existing holes
or mark new location and pre-drill 3/32" new holes. Install
and set to locked position. Align keeper (2) with cam, pre-drill
holes (if needed) and install.
Compruebe nueva pestillo y retén de alineación y los orificios
espaciados adecuados en marco de la ventana. Monte el
cerrojo (1) en los orificios existentes o marque la nueva
ubicación y taladre orificios nuevos de 3/32". Instale mueva
el cerrojo a la posición de cerrado. Alinee la sujetador (2) con
leva, taladre los orificios (si es necesario) e instale.
Vérifiez nouvelle loquet et verrou de l'alignement et de trous
espacements appropriés sur châssis de fenêtre. Installez le
loquet (1) dans les orifices existant ou marquez la nouvelle
position et percez des orifices de 3/32". Installez et réglez
à la position verrouillée. Alignez le cliquet (2) sous la came,
percez les orifices et installez.
Check new latch and keeper for proper alignment and hole
spacings on window frame. Mount latch (1) in existing holes
or mark new location and pre-drill 3/32" new holes. Install
and set to locked position. Align keeper (2) with cam, pre-drill
holes (if needed) and install.
Compruebe nueva pestillo y retén de alineación y los orificios
espaciados adecuados en marco de la ventana. Monte el
cerrojo (1) en los orificios existentes o marque la nueva
ubicación y taladre orificios nuevos de 3/32". Instale mueva
el cerrojo a la posición de cerrado. Alinee la sujetador (2) con
leva, taladre los orificios (si es necesario) e instale.
Vérifiez nouvelle loquet et verrou de l'alignement et de trous
espacements appropriés sur châssis de fenêtre. Installez le
loquet (1) dans les orifices existant ou marquez la nouvelle
position et percez des orifices de 3/32". Installez et réglez
à la position verrouillée. Alignez le cliquet (2) sous la came,
percez les orifices et installez.
Check new latch and keeper for proper alignment and hole
spacings on window frame. Mount latch (1) in existing holes
or mark new location and pre-drill 3/32" new holes. Install
and set to locked position. Align keeper (2) with cam, pre-drill
holes (if needed) and install.
Compruebe nueva pestillo y retén de alineación y los orificios
espaciados adecuados en marco de la ventana. Monte el
cerrojo (1) en los orificios existentes o marque la nueva
ubicación y taladre orificios nuevos de 3/32". Instale mueva
el cerrojo a la posición de cerrado. Alinee la sujetador (2) con
leva, taladre los orificios (si es necesario) e instale.
Vérifiez nouvelle loquet et verrou de l'alignement et de trous
espacements appropriés sur châssis de fenêtre. Installez le
loquet (1) dans les orifices existant ou marquez la nouvelle
position et percez des orifices de 3/32". Installez et réglez
à la position verrouillée. Alignez le cliquet (2) sous la came,
percez les orifices et installez.
  • Page 1 1

Prime-Line F 2755 Operating instructions

Brand
Prime-Line
Model
F 2755
Type
Operating instructions

Prime-Line F 2755 is a window latch and keeper set that can be used to replace or repair existing latches and keepers on windows. The set includes a latch and a keeper, both of which are made of durable materials. To mount the latch, you can either use the existing holes in the window frame or drill new holes. The keeper must be aligned with the latch and can be pre-drilled if necessary. The latch can be set to a locked position, and the keeper can be aligned with the cam. The set comes with all the necessary hardware for installation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents