Chipolino Car Seat Operating instructions

Chipolino
Brand
Chipolino
Model
Car Seat
Category
Car seat
Type
Operating instructions
This child restraint system is designed and manufactured
in compliance with the requirements of Regulation 44 of the United Nations
Economic Commission for Europe concerning the safe transportation of
children, the provisions of the Product safety Directive 2001/95/EU of the
European Parliament and The Council as well as the Consumer Protection Law
from National Legislation.
IMPORTANT! KEEP THIS MANUAL FOR FUTURE REFERENCE!
INSTRUCTION MANUAL FOR USE OF
CHILD RESTRAINT SYSTEM
„JOURNEY”
1
CAR FRONT
REAR
Outer Centre
Refer to
Vehicle list
Yes Yes No
NOTICE
For universal child restraint , groups 0+, I , II and III
1. This is a “UNIVERSAL” CHILD RESTRAINT. It is approved to Regulation No 44, 04 series of
amendments, for general use in vehicles and it will t most, but not all, car seats.
2. A correct t is likely if the vehicle manufacturer has declared in the vehicle handbook that the
vehicle is capable of accepting a “universal” child restraint for these age groups.
3. This child restraint has been classied as “universal” under more stringent conditions than those
which applied to earlier designs which do not carry this notice.
4. If in doubt, consult either the child restraint manufacturer or the retailer.
N O T I C E
for semi-universal child restraint, group 0+
1. This is an ISOFIX CHILD RESTRAINT. It is approved to Regulation No 44, 04 series of amend-
ments, for general use in vehicles tted with ISOFIX anchorages systems.
2. It will t vehicles with positions approved as ISOFIX positions (as detailed in the vehicle hand-
book), depending on the category of the child seat and of the xture.
3. The mass group and the ISOFIX size class for which this device is intended is GROUP 0+ (0-13
kg) with ISOFIX class D.
NOTICE
for semi-universal child restraint groups 0+, I , II и III
This child restraint is classied Semi-universal use and is suitable for xing into the seat positions of
the following car:
Seat positions in other cars may also be suitable to accept this child restraint. If in doubt, consult
either the child restraint manufacturer or the retailer.
DO NOT FORGET THAT NO RESTRAINT SYSTEM CAN PROVIDE
ABSOLUTE PROTECTION IN CASE OF A CRASH OR ROAD ACCIDENT!
DRIVE WITH CARE WHEN THERE IS A CHILD IN YOUR VEHICLE!
IN ORDER TO ENSURE THE SAFETY OF YOUR CHILD, FOLLOW EXACTLY
THE INSTRUCTIONS AND SAFETY RECOMMENDATIONS IN THIS MANUAL!
MISUSE OF THE CAR SEAT WILL CONTRIBUTE TO REDUCING ITS SECURITY
AND SAFETY FEATURES! FAILURE OF THE GUIDELINES OF THIS
INSTRUCTION INCREASES THE RISK OF SERIOUS INJURY OR DEATH!
2
CAUTION!
NEVER INSTALL THE CAR SEAT IN FORWARD FACING POSTION BEFORE THE CHILD’S
WEIGHT EXCEEDS 9 kg!
Do not place the restraint system on a vehicle
seat equipped with air bag! This may result in
death or serious injury!
Review the instructions of the vehicle for informa-
tion about airbags and conditions of transporta-
tion of children.
PLACE OF THE CAR SEAT IN THE VEHICLE
„REARWARD FACING”
CORRECT
INCORRECT
1 – Do not install child car seat on front seat
equipped with air bag
2 – Install the child car seat ONLY in vehicles
equipped with 3-point safety belt.
„FORWARD FACING”
Diagonal belt
Lap belt
CAUTION! This car seat must be used only in
vehicles tted with APPROVED LAP/ 3-POINT/
STATIC / WITH RETRACTOR CAR SAFETY
BELTS, approved according to rule № 16 of
UNECE and the relevant national laws!
CORRECT
INCORRECT
1 – Do not install child car seat on front seat
equipped with air bag
2 – Install the child car seat ONLY in vehicles
equipped with 3-point safety belt.
?
1
?
1
?
2
?
2
1
1
2
2
3
CAUTION! NEVER LEAVE YOUR CHILD UNATTENDED!
CAUTION! DO NOT USE ANCHOR POINTS OTHER THAN THE ONES DESCRIBED IN THIS
MANUAL AND MARKED ON THE RESTRAINT SYSTEM.
CAUTION! NEVER INSTALL THE CHILD RESTRAINT IN THE DIRECTION OF VEHICLE
MOVEMENT AND FACING FORWARD BEFORE THE CHILD WEIGHT REACHES 9kg!
CAUTION! THE CAR SEAT SAFETY MUST BE PROPERLY ADJUSTED ACCORDING TO CHILD’S
HEIGHT, NOT TWISTED AND SNUG WELL AGAINST BABY’S BODY.
CAUTION! THIS CHILD RESTRAINT SHOULD NOT BE MODIFIED OR ADAPTED WITH NEW
FITTINGS, WITHOUT PREVIOUS AUTHORIZATION BY THE COMPETENT AUTHORITY.
CAUTION! KEEP AWAY FROM FIRE!
Installation in the vehicle and securing the child in the car seat to be done only by adult!
The hard parts and the parts of the child restraint made of plastic should be located and installed
so that when the vehicle is in normal use, they can not be trapped by a sliding seat or in a door of
the vehicle.
Do not allow the safety belts of the car seat and the vehicle to be twisted, frayed or torn, latches and
locks (buckles) must be always in good order and rmly xed.
If you nd uncertainty or defect in the structure, latches, straps or locking mechanisms of the car
seat or ISOFIX attachments , discontinue usage until removal of the damaged parts and
replacement with new ones.
After a violent impact the car seat and belts may be damaged. therefore, it is recommended to
replace the car seat with new one.
Never use a second hand child restraint. it may have suffered structural damage, which may make
the child restraint extremely dangerous.
Do not use this car seat without its seat cover and do not replace it with a new one, unless supplied
by the manufacturer. The fabric parts are integral parts of the restraint system and its safety
features!
Always make sure that you are not carrying any unsecured objects, especially on the back shelf,
which, in case of an accident, may injure the car’s occupants
Do not put additional pads except the ones supplied from the manufacturer! Placing additional pads
may obscure the safety of your child.
Car seat JOURNEY
Group
Kgs of the
child
Method of installation in the vehicle
0+ 0-13 kg
ISOFIX attachment + top tether +
5- point safety belt of child car seat (rearward facing)
0+ & I 0-18 kg
3- point vehicle safety belt + 5- point
safety belt of child car seat (rearward facing)
I 9-18 kg
Additional ISOFIX attachment +
5- point safety belt of child car seat +
3- point vehicle safety belt (forward facing)
I 9-18 kg
3- point vehicle safety belt + 5- point
safety belt of child car seat (forward facing)
II & III 15-36 kg 3- point vehicle safety belt (forward facing)
II & III 15-36 kg
3- point vehicle safety belt +
additional ISOFIX attachment (forward facing)
4
Do not use spare parts and other components not supplied by the manufacturer. The manufacturer
assumes no responsibility for safety in the event that are used spare parts other than original.
It is recommended to cover the car seat if the vehicle is parked under strong sun shine – extreme
sun exposure will make the plastic to deteriorate and the fabric to fade. Please, check that the child
restraint has not become too hot before placing your child seat.
The child car seat does not replace the child's cot or bed. When a child needs a sleep, you have to
place him in a suitable baby stroller, baby crib or bed.
Do not attach objects with long cords or strings on the car seat in order to avoid danger of
suffocation!
Never place a child seat on beds, couches or similar soft surfaces!
Do not allow children to play with the product!
Do not remove stickers and warnings – they contain important information!
The packaging of the product must be kept out of the reach of children at the time of and after
unpacking in order to avoid the risk of strangulation!
Child restraint restraint while traveling in a vehicle designed for children weighing from 0 to 36 kg
(approx. age 0-12 years), classied in weight groups:
• 0+ (0-13 kg): universal and semi-universal integral ISOFIX child restraint, ISOFIX class D.
The restraint system is installed in direction opposite to the direction of the vehicle and the child is
"rearward facing";
• I (9-18kg): universal and semi-universal integral ISOFIX child restraint. The restraint system is
installed in direction opposite to the direction of the vehicle and the child is "rearward facing" or in
the direction of the vehicle and the child is “facing forward”;
• II (15-25kg): universal and semi-universal non-integral system for securing children.
The restraint system is installed in the direction of the vehicle and the child is “facing forward”;
• III (22-36kg): universal and semi-universal non-integral system for securing children.
The restraint system is installed in the direction of the vehicle and the child is “facing forward”;
ISOFIX attachments to vehicle (for groups 0+), ISOFIX class D;
Possibility for additional xing of the car seat groups I, II and III with ISOFIX connectors;
Top tether (only for groups 0+ , “REARWARD FACING“ car seat);
The restraint rotates 360 degress on the base;
Backrest recline;
Head rest height adjustment;
5-point safety harness on the restraint;
Additional soft pads;
PRODUCT FEATURES
• Follow exactly the instructions and sequence of installation steps and use of the product
described in the text and gures of this manual.
• Check the security of xing after each operation!
• ALWAYS CHECK THE SECURITY OF FIXING OF THE SAFETY BELTS!
• After each installation make sure that the seat belts are not twisted and are in the correct
position.
• IMPORTANT!
INSTRUCTIONS FOR USE
5
1. ISOFIX guides
If your vehicle is not equipped with ISOFIX guides, place the ISOFIX guides (02), attached to car seat
into the devices of vehicle (01), located between seat and backrest.
2. Releasing of ISOFIX guides
Press releasing button (13) and move the anchors maximum forwards.
3. Shoulder belts adjustment
Press the button for belt adjustment (04), pull both shoulder belts (05) simultaneously and adjust them
maximum.
Note: Pull the shoulder belts (05), not shoulder soft pads (06).
CAUTION! Shoulder belts must be at the same height level as shoulder of the child.
4. Pull the mechanism (07) and move the head support (08) in suitable for the child position.
5. Pull the mechanism (07) and move the headrest support (08) in suitable for the child position.
6. CAUTION! Head support (08) must be set so that the distance between the shoulder of the child and
head support (08) to be around two ngers.
ISOFIX
HEADREST ADJUSTMENT WHILE USING 5-POINT BELT OF CHILD CAR SEAT
(GROUPS 0+ AND I)
HEADREST ADJUSTMENT WHILE USING 3-POINT VEHICLE SAFETY BELT
(GROUPS II AND III)
6
“click”
Release
button
7. Backrest recline of the seat.
Pull the mechanism (10) and move the seat (11) in required position. Release the mechanism and the
position will be xed.
8. 360 degrees rotation.
Pull the mechanism (32) and rotate the seat (11) until you reach the required position. Release the
mechanism (32) and the position xes automatically.
BACKREST RECLINE AND 360 DEGREES ROTATION OF SEAT
INSTALLATION OF THE CAR SEAT GROUP 0+ (0-13 KG)
ISOFIX ATTACHMENT + TOP TETHER + 5-POINT SAFETY BELT
OF CHILD CAR SEAT
WARNING!
MAKE SURE BELTS
OF VEHICLE ARE NOT
TWISTED AND ARE IN
CORRECT POSITION!
7
9. Release the ISOFIX anchors
Set the backrest in position R. Make sure seat is stable xed and does not move.
Place the child car seat onto the vehicle seat to be REARWARD FACING. Attach the car seat ISOFIX
anchors (12) to the vehicle devices until you hear a click sound.
10. ISOFIX indicator must show green color, which means the ISOFIX anchors (12) installation is cor-
rect.
11. Car seat must be as close as possible to the backrest of vehicle seat.
12, 13, 14, 15 – Attach the top tether.
Release and pull the belt up to the needed length and insert it through one of the guiders (14). Fix to the
corresponding place in the vehicle.
16 – CAUTION! Tighten the top tether belt until the indicator of adjustment mechanism shows green
color (3). If the indicator does not show green color, do the installation again.
17. CAUTION! Place the car seat onto vehicle seat so that child is REARWARD FACING!
18 – Pull 3-point vehicle belt.
19, 20, 21 – Insert the diagonal and lap belt through the corresponding guides and lock the buckle.
ATTENTION! Make sure the vehicle belts are snug and car seat is properly xed to the vehicle seat.
SECURING THE CHILD WITH 5-POINT SAFETY BELT OF CAR SEAT
22 – Loosen the shoulder belts (see article 3) and press the button of the central buckle (19) to unfasten
the safety belt.
23, 24, 25 – Place the child in the car seat. Join the metal endings (20) of the shoulder belts and insert
them together into the central buckle (19).
26, 27 – Tighten the belts to snug child’s body as pulling the strap that adjusts the length of the belts.
CAUTION! Belts must not be twisted and they should not bring discomfort to the child.
INSTALLATION OF THE CAR SEAT GROUP 0+ and I (0-18 KG)
3-POINT VEHICLE BELT + 5-POINT SAFETY BELT OF CHILD CAR SEAT
“click”
“click”
Diagonal
belt guide
Lap
belt
guide
pull
WARNING!
MAKE SURE BELTS OF
VEHICLE ARE NOT
TWISTED AND ARE IN
CORRECT POSITION!
8
INSTALLATION OF THE CAR SEAT GROUP I (9 -18 KG)
3-POINT VEHICLE BELT + 5-POINT SAFETY BELT OF CHILD CAR SEAT
28 – CAUTION! Place the car seat onto vehicle seat so that child is FORWARD FACING!
29, 30 – Set the backrest in position F (upright). Pull 3-point vehicle belt and insert it through the opening
between basis (22) and seat and through both guides (23). Lock the buckle.
31, 32, 33 – Place the diagonal belt (1) and lap belt (2) under the soft pad and tighten them.
ATTENTION! Make sure the vehicle belts are snug and car seat is properly xed to the vehicle seat.
34, 35, 36, 37, 38, 39 – Place the child in the car seat and secure him/her with 5-point safety belt
(See 22 up to 27).
“click”
“click”
WARNING!
MAKE SURE BELTS OF
VEHICLE ARE NOT
TWISTED AND ARE IN
CORRECT POSITION!
9
INSTALLATION OF THE CAR SEAT GROUP I (9 -18 KG)
ADDITIONAL FIXING + 3-POINT VEHICLE BELT + 5-POINT SAFETY BELT
OF CHILD CAR SEAT
40 – CAUTION! Place the car seat onto vehicle seat so that child is FORWARD FACING!
Install the car seat with ISOFIX anchors to the vehicle seat (See article 9).
41 – CAUTION! ISOFIX indicator must show green, which means ISOFIX anchors (12) are xed
properly.
42, 43, 44, 45, 46 – Set the backrest in position F (upright) and insert 3-point vehicle belt
(see description 29-33).
ATTENTION! Make sure the vehicle belts are snug and car seat is properly xed to the vehicle seat.
47, 48, 49, 50, 51, 52 – Place the child in the car seat and secure him/her with 5-point safety belt
(See 22 up to 27).
“click”
“click”
“click”
WARNING!
MAKE SURE BELTS OF
VEHICLE ARE NOT
TWISTED AND ARE IN
CORRECT POSITION!
10
INSTALLATION OF THE CAR SEAT GROUPS II (15 -22 KG) and III (22 -36 KG)
3-POINT VEHICLE BELT + ADDITIONAL FIXING
INSTALLATION OF THE CAR SEAT GROUPS II (15 -22 KG) and III (22 -36 KG)
WITH 3-POINT VEHICLE BELT
53 – CAUTION! Remove 5-point child car seat safety belts and place the car seat in vehicle, so the child
is FORWARD FACING! Set the backrest is position F (upright). Place the child in car seat. Set the head
support according to child’s height (see article 5 and 6). Pull the vehicle safety belt around the child and
lock it in the buckle (24).
54 – Place the diagonal belt as shown in gure (25 – Diagonal belt, 26 – Lap belt, 27 – Diagonal belt
guide).
55 – Place the lap belt as shown in gure (26 – Lap belt, 28 – Lap belt guide).
56 – Note: Diagonal belt must go through head support guide and must not be twisted.
CAUTION! Diagonal belt must go above child shoulder, but not above his/her neck!
ATTENTION! Make sure the vehicle belts are snug and car seat is properly xed to the vehicle seat.
“щрак”
“click”
WARNING!
MAKE SURE BELTS OF
VEHICLE ARE NOT
TWISTED AND ARE IN
CORRECT POSITION!
11
57 – CAUTION! Remove 5-point child car seat safety belts and place the car seat in vehicle, so the child
is FORWARD FACING! Set the backrest is position F (upright).
Install the car seat with ISOFIX anchors to the vehicle seat (see article 9).
CAUTION! ISOFIX indicator must show green, which means ISOFIX anchors (12) are xed properly.
58, 59, 60 – Place the child in car seat and secure him/her with the 3-point vehicle belts (see 53-56).
61 – Note: Diagonal belt must go through head support guide and must not be twisted.
CAUTION! Diagonal belt must go above child shoulder, but not above his/her neck!
ATTENTION! Make sure the vehicle belts are snug and car seat is properly xed to the vehicle seat.
Press the button for ISOFIX anchors releasement.
If any change the ISOFIX indicator will go from
green to red color, ISOFIX anchors are released
and car seat can be removed from the vehicle seat.
Stow back ISOFIX anchors to the base of the car
seat.
1. Set the head support in its highest position.
2. Remove the fabric from head support.
3. Remove the upholstery from the car seat (31).
REMOVAL OF ISOFIX ANCHORS FROM VEHICLE SEAT
REMOVAL OF UPHOLSTERY
12
CARE AND MAINTENANCE
Clean the fabrics, plastic parts and metal parts with damp cotton cloth or sponge and mild soap
Upholstery may be hand washed at 30
0
С using mild detergent!
Do not bleach! Do not tumble dry! Do not machine wash! Do not iron!
Do not use abrasive, bleach or other aggressive detergents.
Always after cleaning leave the car seat fully dry and after that use it or store it.
Harnesses must be cleaned with damp cloth and mild soap!
Do not wet or remove the stickers. They contain important information!
Always store your car seat indoors – on dry and clean place. Do not expose to direct environment
inuence - sun, rain, moisture and high temperature intervals.
Please, contact your authorized dealer for problems connected with the use or repair.
Fabric:
Outer: 100% polyester
Filling: 100% polyester
Materials used: plastic, metal, textile
STKJR021xxxx
13
List of vehicles, suitable for xing
of semi-universal child restraint
system, model „JOURNEY”
14
15
Bulgaria, Plovdiv, Golyamokonarsko shosse Str. № 1
www.chipolino.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Chipolino Car Seat Operating instructions

Chipolino
Brand
Chipolino
Model
Car Seat
Category
Car seat
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents