Chief FSB-75100 User manual
- Category
- Wall & ceiling mounts accessories
- Type
- User manual
Chief FSB-75100 is a small display interface kit that provides a convenient and secure way to mount a display to a wall or other surface. It is compatible with a variety of displays and features a tilt range of +5° to -15°, allowing you to adjust the viewing angle to your preference. The kit includes all the necessary hardware for installation, including mounting buttons, spacers, and screws.
Chief FSB-75100 is a small display interface kit that provides a convenient and secure way to mount a display to a wall or other surface. It is compatible with a variety of displays and features a tilt range of +5° to -15°, allowing you to adjust the viewing angle to your preference. The kit includes all the necessary hardware for installation, including mounting buttons, spacers, and screws.
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief, a products division of Milestone AV Technologies
6436 City West Parkway, Eden Prairie, MN 55344
• P: 800.582.6480 / 952.225.6000 • F:877.894.6918 / 952.894.6918
8800-002666 Rev00
©2014 Milestone AV Technologies
12/14
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE
PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY
AND DAMAGE TO EQUIPMENT! DO NOT over tighten screws
when installing mounting buttons.
Flush Mount Display Interface Installation
1. Place display face down on a clean dry surface.
2. Assemble mounting buttons (A) to display using four M4 x 20mm
(D) Phillips pan head screws. (See Figure 1)
Figure 1
Recessed Mount Display Interface Installation
1. Align and place four spacers (B or C) over mounting holes in
display back. (See Figure 2)
2. Place mounting buttons (A) over four spacers (B or C). (See
Figure 2)
3. Assemble mounting buttons (A) to display using four M4 x 25mm
(E) or four M4 x 30mm (F) Phillips pan head screws through
spacers. (See Figure 2)
Figure 2
Chief® is a registered trademark of Milestone AV Technologies. All
rights reserved.
2
(D) x 4
(A)
3
(E or F) x 4
(B or C) x 4
(A)
FSB-75100
Small Display Interface Kit
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
TOOLS REQUIRED FOR INSTALLATION / PARTS
B (4)
3/4" x 1/4" C (4)
3/4" x 1/2"
D (4)
M4 x 20mm E (4)
M4 x 25mm
F (4)
M4 x 30mm
A (4)
[Mounting buttons]
INSTALLATION INSTRUCTIONS
Small Flat Panel Tilt Wall Mount
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FTR1U / FTR100
FTR1U / FTR100 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure the mounting system is
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this mounting system can result in serious personal injury
or damage to equipment! It is the installer’s responsibility to
make sure the structure to which this mounting system is
attached can support five times the combined weight of all
equipment. Reinforce the structure as required before
installing the mounting system. The wall to which the
mounting system is being attached may have a maximum
drywall thickness of 5/8” (1.6cm). Do not install drywall
anchors into the seam between drywall pieces.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to FTR1U/FTR100 mounting system
does not exceed 45 lbs (20.4 kg).
WARNING: Watch for pinch points! Do NOT place fingers
in between moving parts!
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this mounting system outdoors.
IMPORTANT ! :
The FTR1U/FTR100 mounts are designed to
be mounted to a:
•single 2" x 4" wood stud; OR a
•single 2" x 4" wood stud on one side and drywall on the
other side using the drywall anchors provided.
NOTE: The FTR1U includes the Chief FSB1U interface
bracket.
NOTE: The FTR100 includes the Chief FSB75100 interface
bracket.
--SAVE THESE INSTRUCTIONS--
Installation Instructions FTR1U / FTR100
3
DIMENSIONS
0.25
6.4 x6
6.37
161.7 5.61
142.5
1.56
39.6
3.94
100MM
MOUNTING
1.97
50MM
MOUNTING
0.44
11.1 1.97
50.0
3.94
100.0
3.12
79.1
5.78
146.7
4.75
120.7
1.90
48.2
FACE TILTS
5 UP
15 DOWN
4.00
101.6
0.50
12.7
0.38
9.5
0.99
25.2
2.50
63.5
4.00
101.6
1.38
34.9 1.88
47.6 2.38
60.3
3.75
95.3
2.07
52.5
DIMENSIONS: INCHES
[MILLIMETERS]
FTR1U / FTR100 Installation Instructions
4
LEGEND
TOOLS REQUIRED FOR INSTALLATION
PARTS
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Hammer
Martillo
Hammer
Martelo
Martello
Hamer
Marteau
#2
1/8” (wood stud)
3/8” (drywall)
A (1)
[FTR1U/FTR100 Assembly]
#10 x 2-1/2”
B (2)
C (4)
#10
D (2)
10-24
[Hollow wall anchor]
Interface bracket (including
hardware and
installation instructions)
Installation Instructions FTR1U / FTR100
5
INSTALLATION
The FTR1U/FTR100 may be installed either centered on a
single wood stud, or anchored to a single wood stud on one
side, and to drywall (1/2” minimum thickness) on the other side.
The FTR1U/FTR100 allows a tilt range from +5° to -15°.
Install Mount Centered to Single Wood Stud
1. Determine approximate mounting location, keeping in mind
the display size.
2. Use a stud sensor to locate applicable wood stud. Mark
location with a pencil.
3. Level FTR1U/FTR100 assembly (A) at desired height and,
using it as a template, mark the location of upper and lower
pilot holes. Ensure marks are in the center of wood stud.
NOTE: Mount can provide ±1/2” of lateral shift by using mount
holes on either side of vertical center line.
WARNING: ELECTRICAL SHOCK HAZARD! Drilling into
electrical wires or cables can cause DEATH or SERIOUS
PERSONAL INJURY! ALWAYS make certain area behind
mounting surfaces is free of electrical wires and cables
before drilling or installing mount fasteners.
4. Drill pilot holes using a 1/8” drill bit. Ensure pilot holes are
straight.
5. Fasten
FTR1U/FTR100
assembly to wood stud using two
#10 x 2-1/2” Phillips head screws (B) through two #10
washers (C),
FTR1U/FTR100
assembly (A), and drywall (not
shown) and install into pilot holes. (See Figure 1)
Figure 1
Install Mount to a Single Wood Stud and Drywall
WARNING:
Drywall must have a minimum thickness of 1/2”
and a maximum thickness of 5/8”. Do not install drywall
anchors into the seam between drywall pieces.
1. Determine approximate mounting location, keeping in mind
the display size.
2. Level FTR1U/FTR100 assembly (A) at desired height and,
using it as a template, mark the location of the four anchor
holes (one in each corner slot). (See Figure 2)
IMPORTANT ! : Two holes MUST be centered on a
single wood stud.
WARNING: ELECTRICAL SHOCK HAZARD! Drilling into
electrical wires or cables can cause DEATH or SERIOUS
PERSONAL INJURY! ALWAYS make certain area behind
mounting surfaces is free of electrical wires and cables
before drilling or installing mount fasteners.
3. Drill 1/8” pilot holes in wood stud locations. Ensure pilot
holes are straight. (See Figure 2)
4. Drill 3/8” anchor holes in the other two marked locations.
Ensure holes are straight and completely through drywall.
(See Figure 2)
Figure 2
2
4
x 2
x 2
5
(B) x 2
(A)
(C)
3
x 2
4
x 2
x 4
2
1/8”
3/8”
FTR1U / FTR100 Installation Instructions
6
5. Gently tap two anchors (D) into anchor holes. Anchor barbs
should be fully engaged in drywall. (See Figure 3) and (See
Figure 4)
Figure 3
6. Using Phillips screwdriver, tighten anchor screw until
anchor has fully collapsed against back side of drywall.
(See Figure 4)
NOTE: Anchor screw will feel tight until anchor begins to
collapse. Screw will then turn easier for many turns.
Screw will feel tight when anchor has fully collapsed.
7. Remove and save anchor screws from anchors (D).
NOTE: Anchors (D) may come with small washers which
should be discarded.
Figure 4
8. Insert anchor screws through two #10 washers (C), FTR1U/
FTR100 assembly (A) and install into collapsed anchors
(D). (See Figure 5)
9. Install two #10 x 2 1/2” Phillips tapping screws (B) through
two #10 washers (C), FTR1U/FTR100 assembly (A) and
into wood stud. (See Figure 5)
Figure 5
Install Display to Mount
NOTE: Attach interface bracket to display following instructions
included with interface bracket.
1. Open latching flag by rotating flag clockwise on FTR1U/
FTR100 assembly (A). (See Figure 6)
Figure 6
(D) x 2
5
Drywall
Anchor barb
Anchor
Anchor not
collapsed collapsed
(B) x 2
9
(A)
anchor
8
(D) x 2
screws x 2 (C) x 4
Latching
flag open
Latching
flag closed
1
Installation Instructions FTR1U / FTR100
7
2. Lift and maneuver display such that all mounting buttons fit
into openings on FTR1U/FTR100 assembly (A). (See
Figure 7)
3. Lower display firmly into place. Ensure each mounting
button has fully seated in the opening. (See Figure 7)
4. Close latching flag by rotating flag counterclockwise on
FTR1U/FTR100 assembly (A). (See Figure 7)
Figure 7
NOTE: Example shows mounting display in the 100mm x
100mm pattern. FTR1U/FTR100 assembly (A) will also
accommodate a 75mm x 75mm pattern. (See Figure 8)
Figure 8
NOTE: An optional padlock may be used to secure latching flag
in place. (See Figure 9)
Figure 9
5. Connect cables to display as required.
Adjusting Tilt
1. Loosen adjusting screws on each side of display (See
Figure 10).
2. Adjust tilt as desired.
3. Tighten adjusting screws.
Figure 10
2
3
Display
(A)
4
Latching flag
Button location for
100mm x 100mm
pattern (4 places)
Button location for
75mm x 75mm
pattern (4 places)
NOTE: Display not shown for clarity.
NOTE: Display not shown for clarity.
Add padlock here
5° Tilt Up 15° Tilt Down
123
FTR1U / FTR100 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002877 Rev02
2017 Milestone AV Technologies
www.milestone.com
08/17
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
Chief FSB-75100 User manual
- Category
- Wall & ceiling mounts accessories
- Type
- User manual
Chief FSB-75100 is a small display interface kit that provides a convenient and secure way to mount a display to a wall or other surface. It is compatible with a variety of displays and features a tilt range of +5° to -15°, allowing you to adjust the viewing angle to your preference. The kit includes all the necessary hardware for installation, including mounting buttons, spacers, and screws.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Chief FTR1U Installation guide
-
-
Chief PSB2243 Installation guide
-
-
-
-
-
-
-