CAMDEN CX-91S-06 User manual

CX-91S-06
CAMDEN
Brand
CAMDEN
Model
CX-91S-06
Type
User manual

CAMDEN CX-91S-06 is a surface-mounted magnetic lock designed for single doors. It offers a strong holding force of 600 lbs, making it suitable for a variety of commercial and industrial applications. The lock features adjustable timer, door position switch, bond sensor, relay, and LED for added functionality. With a current draw of 500mA at 12V and 250mA at 24V, it operates on both 12V and 24V DC power sources. The lock's contacts are rated 0.5A@30 V DC/AC for the door position reed switch and 1.0A@30VDC for the bond sensor output relay, ensuring safe operation within these limits.

CAMDEN CX-91S-06 is a surface-mounted magnetic lock designed for single doors. It offers a strong holding force of 600 lbs, making it suitable for a variety of commercial and industrial applications. The lock features adjustable timer, door position switch, bond sensor, relay, and LED for added functionality. With a current draw of 500mA at 12V and 250mA at 24V, it operates on both 12V and 24V DC power sources. The lock's contacts are rated 0.5A@30 V DC/AC for the door position reed switch and 1.0A@30VDC for the bond sensor output relay, ensuring safe operation within these limits.

CX-91S-06 and CX-92S-06 Magnetic Lock
600 Lbs Surface Mount, Single and Double Door
Installation Instructions
Model
Description
Features
Current Draw
CX-91S-06
Single
Basic
500mA @ 12V
250mA @ 24V
CX-91S-06TDS
Single
adj. timer, door position switch,
bond sensor, relay & LED
CX-92S-06
Double
Basic
2 X 500mA @ 12V
2 X 250mA @ 24V
CX-92S-06TDS
Double
adj. timer, door position switch,
bond sensor, relay & LED
SHOCK HAZARD. Care must be taken to keep the power supply and wiring isolated from ground (earth). Use of
an ohmmeter to test for shorts is recommended prior to service.
A. 12V DC Input:
To set the jumpers for 12V DC operation see the adjacent
diagram.
Connect the ground (-) lead from a 12V DC power source to
terminal 2.
Connect the positive (+) lead from a 12V DC power source to
terminal 1.
B. 24V DC Input:
Unit is delivered from Factory with single jumper ON for 24V
operation.
Connect the ground (-) lead from a 24V DC power source to terminal
2.
Connect the positive (+) lead from a 24V DC power source to
terminal.
C. Contacts:
Door Position Reed Switch dry contacts are rated 0.5A@30 V DC/AC.
Bond Sensor Output Relay dry contacts are rated 1.0A@30VDC.
For safe operation, do not exceed this rating.
Note: Only use UL/CUL Listed Regulated Power Source.
Important
Power switch should always be wired as shown below in order to minimize the effect of residual magnetism.
Contact Camden for other wiring considerations.
https://manual-hub.com/
CX-91S-06 and CX-92S-06 Installation Instructions
www.camdencontrols.com
Toll Free: 1.877.226.3369
File: CX-91S-92S-06_Man_NF_Rev2.doc
Revised: May 12, 2010
Part No.:40-82B051
Important! Please read before installation
A. Handle the components with care. Damaging the surfaces of the magnet or armature plate may reduce locking
efficiency.
B. The magnet mounts to the door frame. The armature plate must be mounted to the door with the hardware supplied.
This allows it to pivot about its center to compensate for door wear and misalignment.
C. Affix template with the door in its normally closed position.
D. Mark and drill holes. Mount magnet and armature plate with screws installed finger tight at first. Verify all parts
align correctly, and then
firmly tighten screws.
https://manual-hub.com/
  • Page 1 1
  • Page 2 2

CAMDEN CX-91S-06 User manual

CX-91S-06
CAMDEN
Brand
CAMDEN
Model
CX-91S-06
Type
User manual

CAMDEN CX-91S-06 is a surface-mounted magnetic lock designed for single doors. It offers a strong holding force of 600 lbs, making it suitable for a variety of commercial and industrial applications. The lock features adjustable timer, door position switch, bond sensor, relay, and LED for added functionality. With a current draw of 500mA at 12V and 250mA at 24V, it operates on both 12V and 24V DC power sources. The lock's contacts are rated 0.5A@30 V DC/AC for the door position reed switch and 1.0A@30VDC for the bond sensor output relay, ensuring safe operation within these limits.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents