T3SU ETHERNET BRIDGE OPTION MODULE P/N 1200655L1
For more detailed documentation, visit us online at www.adtran.com
Quick Start Guide
Quick Start Guide, 61200655L1-13A, October 2002 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2002 ADTRAN, All Rights Reserved
SPECIFICATIONS
Interface Type: (4) 10BaseT/100BaseTX interfaces with auto MDI/MDIX
crossover on all interfaces
Flow Control: Back-pressure flow control on all half-duplex interfaces
Pause-frame flow control on full-duplex interfaces
Environmental
Specifications:
Operating Temperature: 0°C to 50°C
Storage Temperature: -20°C to 70°C
Relative Humidity: Up to 95% non-condensing
Compliance: FCC Part 15, Class A
UL 60950, 3rd Edition
EN 60950
ETSI 300 386
NETWORK CONNECTION PINOUT
Pin Name Description
1 TX1 Transmit Positive
2 TX2 Transmit Negative
3 RX1 Receive Positive
4, 5 UNUSED —
6 RX2 Receive Negative
7, 8 UNUSED —
1st Generation T3SU's (AC P/N 1200217L2 and DC P/N
1200217L4) can support a single Ethernet Bridge Module.
2nd Generation T3SU's (AC P/N 1202217L2 and DC P/N
1202217L4) can support up to 3 Ethernet Bridge Modules.
1234
LINK ACT LINK ACT LINK ACT LINK ACT
10/100 BASE T/TX INTERFACE
INSTALLATION INSTRUCTIONS
1. Remove the cover plate from the appropriate option slot in the T3SU
Base Unit.
2. Slide the T3SU Ethernet Bridge Option Module into the option slot until
the module is firmly positioned against the front of the chassis.
3. Secure the thumbscrews at both edges of the module. Tighten with a
screwdriver.
4. Connect the cables to the associated device(s).
5. Complete installation of remaining modules and Base Unit as specified
in the T3SU User Manual.
T3SU ETHERNET BRIDGE OPTION MODULE P/N 1200655L1
Quick Start Guide
Quick Start Guide, 61200655L1-13A, October 2002 Technical Support 1-888-4ADTRAN (1-888-423-8726) Copyright 2002 ADTRAN, All Rights Reserved
MENU TREE
1 - DTE Port State Enabled
Disabled
2 - Port State (TX#1) Enabled
1 - Status 1 - DS3 Network Disabled
2 - Statistics 2 - DTE Ports (Ethernet Bridge) 3 - Speed (TX#1) 1 - 10 Base-T
3 - Configuration 3 - System Management 2 - 100 Base-TX
4 - Diagnostic 4 - Utilities 4 - Duplex (TX#1) 1 - Half Duplex 3 - Auto Detect
5 - Remote Login 2 - Full Duplex
6 - Logout 3 - Auto Detect
5 - Port State* (TX#2)
6 - Speed* (TX#2)
7 - Duplex* (TX#2)
8 - Nx75k blocks (1-588)
Port Bandwidth = X Mbps
9 - Apply Settings
10 - Port State* (TX#3)
11 - Speed* (TX#3)
12 - Duplex* (TX#3)
13 - Port State* (TX#4)
14 - Speed* (TX#4)
15 - Duplex* (TX#4)
16 - Reset Bridge
* For detailed menu options refer to Port State, Speed, and Duplex for TX#1 interface.
-
1
-
2
ADTRAN T3SU 300 Quick start guide
- Type
- Quick start guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ADTRAN T1 User manual
-
ADTRAN What is the correct setting for the Line Length option on the DS3 interface of a T3SU 300 Owner's manual
-
-
-
-
-
-
-
-