LG LRNU12GSF10 Installation guide

Brand: LG

Model: LRNU12GSF10

Category: Split-system air conditioners

Type: Installation guide

This manual is also suitable for

LRNU12GSF10.ANCAASA

LG LRNU12GSF10 is an Art Cool Gallery Series indoor unit, a type of air conditioner that can be installed on a wall to cool or heat a room. It comes with a remote controller that allows you to adjust the temperature, fan speed, and other settings from a distance. The unit has a sleek and modern design that will complement any home décor.

Some of the key features of the LG LRNU12GSF10 include:

Cooling and heating capabilities: The unit can both cool and heat a room, making it a versatile option for year-round comfort.
Remote control: The included remote control allows you to adjust the temperature, fan speed, and other settings from a distance.

Some of the key features of the LG LRNU12GSF10 include:

Cooling and heating capabilities: The unit can both cool and heat a room, making it a versatile option for year-round comfort.
Remote control: The included remote control allows you to adjust the temperature, fan speed, and other settings from a distance.

Type: Art Cool Gallery Series

MODELS: SF Chassis

IMPORTANT

• Please read this installation manual completely before

installing the product.

• Installation work must be performed in accordance with

the national wiring standards by authorized personnel

only.

• Please retain this installation manual for future reference

after reading it thoroughly.

ENGLISH ITALIANO ESPAÑOL FRANÇAIS DEUTSCH

2 Indoor Unit

Art Cool Type Indoor Unit Installation Manual

TABLE OF CONTENTS

Installation Requirements

Required Parts Required Tools

❏Pipes: Gas side

Liquid side

(Refer to Product

Data)

❏Insulation materials

❏Additional drain pipe

❏ Installation guide map

❏Four type "A" screws & plastic

anchors

❏Connecting cable

❏Level gauge

❏Screw driver

❏Electric drill

❏Hole core drill

❏Horizontal meter

❏Flaring tool set

❏Specified torque wrenches

(different depending on model No.)

❏Spanner.......Half union

❏A glass of water

❏Screw driver

❏Hexagonal wrench

❏Gas-leak detector

❏Vacuum pump

❏Gauge manifold

❏Owner's manual

❏Thermometer

❏Holder Remote Controller

Installation Parts ....................3

Safety Precautions.................4

Installation

Selection the best location ....7

Preparing Work for Installation

................................................8

Fixing Indoor Unit...................9

Drill a Hole in the Wall ...........9

Flaring Work.........................10

Connecting the Piping.........11

Drain Piping .........................13

Panel Front Assembly .........14

Wiring Connection...............15

Installation of Remote

Controller..............................16

❏Two type "B" screws

Installation Manual 3

Installation Parts

ENGLISH

Installation Parts

Air Intake

Air Outlet

Type "A" screw and plastic anchor

Type "B" screw

Remote control holder

Installation guide map

Installation Parts

Read carefully, and then follow step by step.

4 Indoor Unit

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be followed.

■ Be sure to read before installing the air conditioner.

■ Be sure to observe the cautions specified here as they include important items related to safety.

■ Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the

following indications.

■ Meanings of symbols used in this manual are as shown below.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Be sure not to do.

Be sure to follow the instruction.

■ Installation

Do not use a defective or under-

rated circuit breaker. Use this

appliance on a dedicated circuit.

• There is risk of fire or electric shock.

For electrical work, contact the

dealer, seller, a qualified electri-

cian, or an Authorized Service

Center.

• Do not disassemble or repair the

product. There is risk of fire or elec-

tric shock.

Always ground the product.

• There is risk of fire or electric shock.

Install the panel and the cover

of control box securely.

• There is risk of fire or electric shock.

Always install a dedicated cir-

cuit and breaker.

• Improper wiring or installation may

cause fire or electric shock.

Use the correctly rated breaker

or fuse.

• There is risk of fire or electric shock.

Installation Manual 5

Safety Precautions

ENGLISH

■ Operation

Do not modify or extend the

power cable.

• There is risk of fire or electric shock.

Do not let the air conditioner

run for a long time when the

humidity is very high and a door

or a window is left open.

• Moisture may condense and wet or

damage furniture.

Be cautious when unpacking

and installing the product.

• Sharp edges could cause injury. Be

especially careful of the case edges

and the fins on the condenser and

evaporator.

For installation, always contact

the dealer or an Authorized

Service Center.

• There is risk of fire, electric shock,

explosion, or injury.

Do not install the product on a

defective installation stand.

• It may cause injury, accident, or

damage to the product.

Be sure the installation area

does not deteriorate with age.

• If the base collapses, the air condi-

tioner could fall with it, causing prop-

erty damage, product failure, and

personal injury.

Do not store or use flammable gas or combustibles near the product.

• There is risk of fire or failure of product.

Gasolin

6 Indoor Unit

Safety Precautions

Always check for gas (refriger-

ant) leakage after installation or

repair of product.

• Low refrigerant levels may cause

failure of product.

Install the drain hose to ensure

that water is drained away prop-

erly.

• A bad connection may cause water

leakage.

Keep level even when installing

the product.

• To avoid vibration or water leakage.

Do not install the product where

the noise or hot air from the out-

door unit could damage the

neighborhoods.

• It may cause a problem for your

neighbors.

Use two or more people to lift

and transport the product.

• Avoid personal injury.

Do not install the product where

it will be exposed to sea wind

(salt spray) directly.

• It may cause corrosion on the product.

Corrosion, particularly on the con-

denser and evaporator fins, could

cause product malfunction or inefficient

operation.

90˚

■ Installation

Installation Manual 7

Installation

ENGLISH

Read completely, then follow step by step.

Installation

Selection of the best location

CAUTION : In case that the unit is installed near the sea, the installation parts

may be corroded by salt. The installation parts (and the unit) should be taken

appropriate anti-corrosion measures.

• Do not have any heat or steam near the unit.

• Select a place where there are no obstacles in front of the unit.

• Make sure that condensation drainage can be conveniently routed away.

Do not install near a doorway.

• Ensure that the space around the left and right of the unit is more than 50cm. The unit should be installed as high on the

wall as possible, allowing a minimum of 10cm from ceiling.

• Use a stud finder to locate studs to prevent unnecessary damage to the wall.

More than 20cm(Minimum)

than 50cm

More than 1.5m

than 50cm

Signal Receptor

Front Panel

Air Discharge

Air Filter

Plasma Filter

Features

8 Indoor Unit

Installation

Preparing Work for Installation

Open panel front

1. Pull the upper part of the front panel.

2. Lift up the panel.

3. To detach the front panel, remove the two screws at the lower part.

4. Detach the front panel from the body.

5. To detach the panel, disconnect the connector at the upper part.

Cover pipe and cover side remove

1. Please remove the screw of the center tuning cover.

2. Pull up the side cover of desired connecting direction, then

cover side is separated.

3. Pick the pipe hole of the side cover.

CAUTION: After removing the pipe hole,

cut the burr for safety.

When making pipe path through rear

wall, you don’t need to pick the pipe hole.

NOTICE

Drain hose junction

1. Remove the rubber stopple in the desired drain

direction.

2. Insert drain hose into the handle of drain pan, and

join drain hose and connecting hose according to

the figure by.

Panel Front

Connector

Side cover

Pipe hole

Only the

desired direction

rubber cap

Only the

desired direction

Connecting

part

Adhesive

Drain

hose

Installation Manual 9

Installation

ENGLISH

Fixing Indoor Unit

• Drill the piping hole with a ø50mm hole core drill.

Drill the piping hole at either the right or the left

with the hole slightly slanted to the outdoor side.

Drill a Hole in the Wall

5-7mm

(0.2~0.3")

Indoor

WALL

Outdoor

Plastic anchors

INSTALLATION GUIDE MAP

INSTALLATION GU

Plastic anchors

INSTALLATION GUIDE MAP

Hanger hole

(Rear side of

the product)

IIA

3. Make a hole with a diameter of 6mm and

depth of 30-35mm by piercing a screw

point.

5. Drive the fore plastic anchors into drilled

points.

7. Hang the hole of product at the upper

screws, and remove the map. (Falling

attention)

9. Check the fixed product with light power.

1. Attach an Installation guide map on the

desired surface.

2. Look at suited horizon by horizontal

meter on the horizontal setting line, and

fix lightly the map by adhesive tape.

Drill the pierted part as a diameter of 50mm

for connecting piping. (In case of piercing

rear surface)

First, Drive the two points of the upper

parts by screws. (Leave 10mm for hanging

the product)

8. Drive the lower parts after facing the hole

of product with plastic anchors, and fix

completely the upper screws.

10.

In case of nothing wrong, connect the

pipe and the wire. (Refer to installation

manual)

Horizontality

10 Indoor Unit

Installation

Flaring Work

Main cause for gas leakage is due to defect in flaring work. Carry out correct flaring work in the following proce-

dure.

Cutting the pipes and the cable.

1. Use the piping kit accessory or the pipes purchased

locally.

2. Measure the distance between the indoor and the out-

door unit.

3. Cut the pipes a little longer than measured distance.

4. Cut the cable 1.5m longer than the pipe length.

Removing burrs

1. Completely remove all burrs from the cut cross section

of pipe/tube.

2. Put the end of the copper tube/pipe in a downward

direction as you remove burrs in order to avoid dropping

burrs into the tubing.

Putting nut on

• Remove flare nuts attached to indoor and outdoor unit,

then put them on pipe/tube having completed burr

removal.

(not possible to put them on after flaring work)

Flaring work

1. Firmly hold copper pipe in a die in the dimension

shown in the table below.

2. Carry out flaring work wiht the flaring tool.

Copper

pipe

90°

Slanted Uneven Rough

Pipe

Reamer

Point down

Flare nut

Copper tube

mm inch mm

Ø6.35 1/4 0~0.5

Ø9.52 3/8 0~0.5

Ø12.7 1/2 0~0.5

Ø15.88 5/8 0~1.0

Ø19.05 3/4 1.0~1.3

Outside diameter A

Bar

Copper pipe

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Bar

"A"

Installation Manual 11

Installation

ENGLISH

Check

1. Compare the flared work with the figure by.

2. If a flared section is defective, cut it off and do flar-

ing work again.

Indoor

Preparing the indoor unit's piping and drain hose for installation through the wall.

CAUTION: If the drain hose is routed inside the room, insulate the hose with an

insulation material* so that dripping from "sweating"(condensation) will not

damage furniture or floors.

*Foamed polyethylene or equivalent is recommended.

1. Route the indoor tubing and the drain hose in the

direction of rear left or right

2. Tape the tubing, drain hose and the connecting

cable. Be sure that the drain hose is located at the

lowest side of the bundle. Locating at the upper side

can cause drain pan to overflow inside the unit.

Inclined

Inside is shiny without scratches

Smooth all round

Even length

all round

Surface

damaged

Cracked Uneven

thickness

= Improper flaring =

Connecting the Piping

Drain hose

Connecting

cable

Gas side piping

Liquid side piping

Drain hose

Loop

Connecting the piping with the indoor unit

and drain hose with drain pipe

1. Align the center of the pipings and sufficiently tight-

en the flare nut by hand.

2. Tighten the flare nut with a wrench.

3. When extending the drain hose at the indoor unit,

install the drain pipe.

Wrap the insulation material around the

connecting portion.

1. Overlap the connection pipe insulation material and

the indoor unit pipe insulation material. Bind them

together with vinyl tape so that there may be no

gap.

2. Wrap the area which accommodates the rear piping

housing section with vinyl tape.

3. Bundle the piping and drain hose together by wrap-

ping them with vinyl tape over the range within

which they fit into the rear piping housing section.

12 Indoor Unit

Installation

Wrap with vinyl tape

Drain hose

Pipe

Vinyl tape(wide)

Indoor unit tubing Flare nut Pipings

Torque wrench

Indoor unit tubing

Spanner (fixed)

Connection pipe

Flare nut

mm inch kgf

Ø6.35 1/4 1.8~2.5

Ø9.52 3/8 3.4~4.2

Ø12.7 1/2 5.5~6.6

Ø15.88 5/8 6.3~8.2

Ø19.05 3/4 9.9~12.1

Outside diameter Torque

Vinyl tape(narrow)

Adhesive

Drain pipe

Indoor unit drain hose

Plastic bands

Insulation material

Vinyl tape(narrow)

Connection

pipe

Connecting cable

Vinyl tape

(wide)

Wrap with vinyl tape

Indoor

unit pipe

Pipe

Installation Manual 13

Installation

ENGLISH

CAUTION: Installation Information

For right piping. Follow the instruction below.

Good case

• Press on the upper side of clamp and unfold the tubing to downward slowly.

Bad case

• Following bending type from left to right may cause damage to the turbing.

Drain Piping

Downward slope

Do not raise

Accumulated

drain water

Tip of drain hose

dipped in water

Air

Waving

Water

leakage

Water

leakage

Ditch

Less than

50mm gap

Water

leakage

1) To check the drainage.

• Pour a glass of water on the evaporator.

• Ensure the water flows through the drain hose of

the indoor unit without any leakage and goes out

the drain exit.

2) Drain piping

• The drain hose should point downward for easy

drain flow.

• Do not make drain piping.

14 Indoor Unit14 Indoor Unit

Installation

Panel Front Assembly

1. First, Check the side cover assembly

exactly, and fix the power cord in the

bottom groove of cover side left.

2. Assemble connecting lead wire with

controller, fix the upper part of panel

front, and match the lower part of panel

front.

3. Screw up panel front, and suspend the

hook of panel front in the groove.

Panel Front

Connector

Installation Manual 15

ENGLISH

Installation

Circuit Breaker

Use a circuit

breaker or time

delay fuse.

• Connect the cable to the indoor unit by connecting the wires to the terminals on the control board in-

dividually according to the outdoor unit connection. (Ensure that the color of the wires of the outdoor unit

and the terminal No. are the same as those of the indoor unit.)

The earth wire should be longer than the common wires.

• When installing, refer to the circuit diagram

on the Control Box of Indoor Unit.

• When installing, refer to the wiring diagram

on the Control Cover Inside Outdoor Unit.

•

The capacity of connection terminal should be over 250V 20A. And when connecting the power line

and communication line between indoor units, you are advised to use the connection terminal.

• When you are not able to use the connection terminal, fix each power line/communication line

by using the clamp cord attached in the product, together with the clamp cord and screw in the

accessories.

Please consider the all

connected capacity of

indoor units.

T/Block Connector

1(L) 2(N) 3 4

T/Block Indoor

1(L) 2(N) 3 4

INDOOR POWER INPUT

Indoor

unit

Outdoor

unit

Central

controller

B E F C D Vcc GND

Main

outdoor unit

Connection Terminal

1.5mm2

1.5mm

Air

Conditioner

Main power source

CAUTION

• The above circuit diagram is subject to change without notice.

• Be sure to connect wires according to the wiring diagram.

• Connect the wires firmly, so that not to be pulled out easily.

• Connect the wires according to color codes by referring the wiring diagram.

CAUTION After the confirmation of the above conditions,

prepare the wiring as follows:

1) Never fail to have an individual power circuit specifically for the air conditioner. As for the method of

wiring, be guided by the circuit diagram posted on the inside of control cover.

2) The screws which fasten the wiring in the casing of electrical fittings are liable to come loose from vibra-

tions to which the unit is subjected during the course of transportation. Check them and make sure that

they are all tightly fastened. (If they are loose, it could cause burn-out of the wires.)

3) Specification of power source.

4) Confirm that electrical capacity is sufficient.

5) See to that the starting voltage is maintained at more than 90 percent of the rated voltage marked on the

name plate.

6) Confirm that the cable thickness is as specified in the power source specification.

(Particularly note the relation between cable length and thickness.)

7) Always install an earth leakage circuit breaker where it is wet or moist.

8) The following would be caused by voltage drop.

• Vibration of a magnetic switch, which will damage the contact point, fuse breaking, disturbance of the normal

function of the overload protection device.

9) The means for disconnection from a power

supply shall be incorporated in the fixed wiring and have an air gap contact separation of at least 3mm in

each active(phase) conductors.

CAUTION If a power plug is not to be used,

provide a circuit breaker between power

source and the unit as shown below.

Wiring Connection

16 Indoor Unit

Installation

16 Indoor Unit

1. Remove the battery cover from the remote controller.

• Slide the cover according to the arrow direction.

2. Insert the two batteries.

• Be sure that the (+) and (-) directions are correct.

• Be sure that both batteries are new.

3. Re-attach the cover.

• Slide it back into position.

HOW TO MOUNT ONTO A WALL

HOW TO INSERT BATTERIES

• Do not use rechargeable batteries,

such batteries differ from standard dry

cells in shape, dimensions, and per-

formance.

• Romove the batteries from the remote

controller if the air conditioner is not

going to be used for some long time.

Installation of Remote Controller(Optional)

P/No.: 3828A23002R

Printed in Korea

After reading this manual, keep it in a place easily accessible to the user for future reference.

LG LRNU12GSF10 Installation guide

Brand: LG

Model: LRNU12GSF10

Category: Split-system air conditioners

Type: Installation guide

This manual is also suitable for

LRNU12GSF10.ANCAASA

Some of the key features of the LG LRNU12GSF10 include:

Cooling and heating capabilities: The unit can both cool and heat a room, making it a versatile option for year-round comfort.
Remote control: The included remote control allows you to adjust the temperature, fan speed, and other settings from a distance.

Download PDF

report

LG LRNU12GSF10 Installation guide

This manual is also suitable for

LG LRNU12GSF10 Installation guide

Related papers

Other documents