LANE BARRIER INSTALLATION
Copyright 2019 DoorKing
®
, Inc. All rights reserved.
1601 Arm Down
MOVING ARM
can
cause vehicle damage,
serious injury or death.
STAY CLEAR
of arm
at all times.
NO:
Pedestrians
Bicycles
Motorcycles
WARNING
CLASS
CERTIFIED TO
CAN/CSA C22.2 NO. 247
CONFORMS TO
ANSI/UL-325
VEHICULAR GATE OPERATOR
HP
53382
MODEL
SERIAL
VOLTSPHASE
AMPS 60 Hz
MAX GATE LOAD
DoorKing, Inc., Inglewood, CA
MOVING ARM
can
cause vehicle damage,
serious injury or death.
STAY CLEAR
of arm
at all times.
NO:
Pedestrians
Bicycles
Motorcycles
WARNING
Moving Gate Can Cause
Serious Injury or Death
KEEP CLEAR! Gate may move at any time
without prior warning.
Do not let children operate the gate or play
in the gate area.
This entrance is for vehicles only.
Pedestrians must use separate entrance.
Traffic Direction
Wire MeshWire Mesh
Arm Channel
Arm Down
Ball
Joint
Secondary Arm
Rod Assembly
Secondary Arm Rod Assy
Secondary Barrier Arm (Up Position)
Arm Channel Section
End
Cap
1601 Arm & Cover
Support Post Assembly
Support Post Assembly
Secondary Barrier Arm (Down Position)
Secondary Barrier Arm (Up Position)
10 ft Lane -
P/N 1620-081
3
- 3ft Arm Channel Sections and
2
End Caps (1620-052 Arm 10ft Assy)
12 ft Lane - P/N 1620-083
3
- 3ft Arm Channel Sections,
1
- 2ft Arm Channel Section and
2
End Caps (1620-054 Arm 12ft Assy)
9 ft Lane - P/N 1620-080
2
- 3ft Arm Channel Sections,
1
- 2ft Arm Channel Section and
2
End Caps (1620-050 Arm 9ft Assy)
14 ft Lane -
P/N 1620-085
3
- 3ft Arm Channel Sections, 2 - 2ft Arm Channel Section and 2 End Caps (1620-058 Arm 14ft Assy)
6”
Min
6”
Min
33.5”
12”
36”
34.5”
6”
6”
6”
6”
6”
6”
1”
1”
6”
6”
6”
6”
6”
6”
Use 3000 psi reinforced concrete. It MUST be flat.
DO NOT install directly on asphalt.
Note: Can be installed on existing concrete roadway (no asphalt).
Secondary Barrier
Arm Counterweight
Assembly
Same number of
counterweights MUST
be on each side of plate.
9 ft Lane: Use 30 counterweights (15 on each side)
10 ft Lane: Use 32 counterweights (16 on each side)
12 ft Lane: Use 32 counterweights (16 on each side)
14 ft Lane: Use 34 counterweights (17 on each side)
Install arm channel
sections so arm is
centered in channel.
Sleeve
Anchor
3/4
Secure all to the concrete
using 3/4” x 3” minimum,
1” x 3” maximum
sleeve anchors (not supplied).
Note: Allow an extra 6 inches of
concrete around all structures min.
Note: Secondary barrier arm is a fixed distance for each lane width and
will determine the specific placement of the support post assemblies.
Connect secondary
arm rod assembly
on opposite side of
1601’s arm as
shown. Adjust
using ball joint
fixtures so arm lays
completely in
channel when
down.
Cut off excess threads flush
with top of nut on the
sleeve anchors that will
come in contact with tires.
Drawings NOT to scale.
Plate
Counterweight
Counterweight
Cover
Counterweight
Assembly
Wire Mesh
Arm Channel
Arm Up
Secondary Barrier Arm (Up Position)
Counterweight
Assembly
39.5”