IQ America LP-1803-WH Installation guide

Brand: IQ America

Model: LP-1803-WH

Category: Motion detectors

Type: Installation guide

This manual is also suitable for

LP-1803-BZ

IQ America LP-1803-WH is a promotional LED motion sensor light that can be installed outdoors on a wall or eave and has a detection range of up to 55 feet. It features two adjustable knobs for setting the time (5 seconds to 20 minutes) that the lights will stay on after motion is no longer detected and the outside light level at which the sensor becomes active. The sensor head can be panned left and right, and tilted up or down to customize the detection area.

PROMOTIONAL LED MOTION SENSOR LIGHT

LP-1803

SUPERIOR ADJUSTMENT VERSATILITY

Installation Procedure:

1. Switch off the power.

Dual Mounting Options

5. Caulk around the edge of the

lighting fixture with silicone

sealant to weatherproof around

the junction box (not included).

FIG. 4

This is a “Limited Warranty” which gives you specific legal rights. You

may also have other rights which vary from state to state and province to

province.

For a period of three years from the date of purchase, any malfunction

caused by factory defective parts or workmanship will be corrected at no

charge to you. To obtain a refund or a replacement, return the product to the

place of purchase.

NOT COVERED: Repair service, adjustment and calibration due to

misuse, abuse or negligence. Unauthorized service or modification of the

product or of any furnished component will void this warranty. This warranty

does not include reimbursement for inconvenience, installation, setup time,

loss or use or unauthorized service.

This warranty covers only IQ America products and is not extended to

other equipment and components that a customer uses in conjunction with

our products.

This warranty is expressly in lieu of all other warranties, express or

implied, including any warranty, representation or condition of merchant

ability of that the products are fit for any particular purpose or use, and

specifically in lieu of all special, indirect or incidental or consequential

damages.

Repair or replacement shall be the sole remedy of the customer and

there shall be no liability on the part of IQ America for any special, indirect,

incidental or consequential damages, including but not limited to any loss of

business or profit, whether or not foreseeable. Some states or provinces do

not allow the exclusion or limitation of incidental or consequential damages,

so the above limitation or exclusion may not apply to you. Retain receipt for

warranty claims.

IQ America Three Year Warranty

Rotate the body up to change from wall mount to eave mount as per drawing

below.

Instruction Manual

6. Testing the sensor

Turn on power. Set TIME to 5 sec. and

LUX to "SUN" symbol (fully counter-

clockwise) for daylight operation. This

will allow you to test the sensor and

make any necessary adjustments to

the coverage area that you want the

sensor to "see"

7. After testing the product and aiming the sensor and lights the way you want

them, it is recommended to turn the LUX knob fully clockwise to the "Moon"

symbol, so the sensor only works at night. If you want to fine-tune the

amount of light outside before the sensor becomes active, you can turn the

LUX knob counter-clockwise to have the sensor work when it is lighter (not

completely dark) outside.

The TIME knob should be turned up to at least 20 seconds, so the lights will

stay on long enough to be useful. Most people find that 2 minutes or 5

minutes is a good setting, but you can extend to as much as 20 minutes if

you desire.

NOTE: The motion sensor will need to completely warm up (35 seconds)

before beginning the setup process. FIG. 11

1215E1

Customer service number:

For problems or questions, please call us at 1-800-296-1869

Instructions: Please retain this instruction manual for future reference

Manual mode overrides the motion sensor and

“ON-TIME” control so the light will turn ON at

full brightness.

This feature only works at night for 6 hours.

The motion sensor will reset to motion sensing

mode. Manual mode can be toggled on and off

using the light switch.

• To manually turn the lights “ON”, turn the light

switch OFF and back ON again between 0.2

sec to 1.5 seconds.

• To cancel the manual override mode, turn the

light switch OFF and back ON again between

0.2 to 1.5 seconds. FIG. 13

• Do not aim motion detectors at objects with highly-reflective surfaces, like

swimming pools, mirrors, etc...

• Do not install motion detectors

near heat sources such as

heating outlets, air conditioning

systems, dryer vents, lighting

fixtures, etc... FIG. 5

• Do not aim the motion detector at

objects that move in the wind,

such as tree limbs or bushes,

large plants, etc...

Lamp Adjustment

Sensor Head Adjustment

The sensor head can be panned to left and right. It can also be tilted

up or down. FIG. 7

Since the motion detector reacts to variations in temperature; avoid the

following situations:

Installation Advice:

WARNING

2. Install the mounting bracket (02) with screws (07 or 08) to the junction box.

FIG. 1 Connect the house wires to the connector wires (04). Connect the

white wire (N) to the white connector wire and

black wire (H) to black connector wire with wire

nuts (05).

Connect the ground wire from the

house wiring to the ground screw on

the mounting bracket (02).

• White to white (N)

• Black to black (H)

Note: Make sure all the wires are inside the junction box before attaching the

main body to the junction box.

4. Plug the wire connector (04) into the

plug on the back of the lighting

fixture. Align the body of the lighting

fixture over the mounting bracket

screw and mount the fixture so the

screw comes through the front of the

light fixture. Thread the decorative

nut (06) onto the screw and tighten.

FIG. 3

3. Insert the house wiring and wire nuts into the junction box,

but make sure the connector wire

(04) is still outside of the junction

box.

Attach the gasket 1 (03) to the

mounting bracket (02), so that the

mounting bracket screw goes

through the gasket. FIG. 2

Wall mount Eave mount

This package contains:

USING MANUAL OVERRIDE MODE

NOTE: If the power to the

light fixture is off for more

than 5 seconds, allow the

motion sensor to warm up

prior to switching to

manual mode.

Turn the light switch Off

and back On again with

0.2 to 1.5 seconds.

02 X 1

Mounting

Bracket

01 X 1

Instruction

Manual

05 X 2

Wire Nuts

06 X 1

Decorative

Nut

07 X 2

Screws

08 X 2

Screws

04 X 1

Connector

Wires

03 X 1

Gasket 1

You will require:

Tools / Equipment need for installation.

Seal with

silicone caulk

Setting the time (TIME). FIG. 10

Setting light level (LUX). FIG. 10

Set the desired time of 5 s – 20 min using the knob.

The lights will stay on for the selected period, after the sensor no longer

detects motion.

OFF

TIME: LUX:

Settings

The motion detector has two knobs underneath for setting the time (TIME)

and the outside light level at which the sensor becomes active. (LUX).

TIME: LUX:

45º

40º

(Main body)

50º

70º

Lights can be panned

outward 50º FIG. 8

Lights can be tilted down 70º .

FIG. 9

Decorative Nut

FIG. 5

FIG. 13

up to 55 FEET

180º

6 FEET

Exit On

180º

8 FEET

FIG. 6

Detection Range:

Recommended installation height is up 8 feet above ground,

the maximum detection range about 55 feet. FIG. 6

FIG. 7

FIG. 8

FIG. 9

FIG. 10

FIG. 2

FIG. 3

FIG. 4

FIG. 11

Potential high temperature!

Do not touch the metal parts of the device.

FIG. 12

Hot Surface Do Not Touch

CAUTION!

FIG. 12

Gasket 1

FIG. 1

Set desired function: moon (night) for complete darkness or

sun (day) for full brightness.

20m

5 sec.

WARNING: This equipment has been tested and found to comply with

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

■ Reorient or relocate the receiving antenna.

■ Increase the separation between the equipment and the receiver.

■ Connect the equipment into an outlet on a circuit different from that to which

■ the receiver is connected.

■ Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

WARNING: “THIS PRODUCT MUST BE INSTALLED IN

ACCORDANCE WITH THE APPLICABLE INSTALLATION

CODE BY A PERSON FAMILIAR WITH THE CONTSTRUC-

TION AND OPERATION OF THE PRODUCT AND THE

HARZARDS INVOLVED”

CMY

IQA Promotional LED LP1803 IM English & Spanish 270116.pdf 1 27/01/16 4:03:35 PM

IQ America LP-1803-WH Installation guide

Brand: IQ America

Model: LP-1803-WH

Category: Motion detectors

Type: Installation guide

This manual is also suitable for

LP-1803-BZ

Download PDF

report

IQ America LP-1803-WH Installation guide

This manual is also suitable for

IQ America LP-1803-WH Installation guide

Related papers

Other documents