Owners Manual
Mounting instruction Öhlins front fork kit
FG 832 for Honda VTR 1000 SP1
Rebound damping
adjuster
Compression
damping adjuster
Öhlins front fork 43
Your Öhlins front fork 43 is an upside down type
front fork featuring the following adjusters.
Compression damping adjuster
Adjustments are made at the bottom of the front
fork leg. Use a 3 mm allen key.
Rebound damping adjuster
Adjustments are made at the top of the fork leg.
Use a 3 mm allen key.
Spring preload adjuster
Adjustments are made by turning the nut at the
top of the fork leg. Clockwise for harder adjust-
ment, counter clockwise too release the preload.
Use a 17 mm wrench.
NOTE!
When delivered the Öhlins front fork is dialed to
recommended settings for the specific brand and
make of the motorcycle. If you have changed the
setting check like this:
The adjusters have a normal right hand thread. Turn
the damping adjusters clockwise to fully closed (pos.
zero [0]). Turn counter clockwise to open and count
the clicks until you reach the recommended number
of clicks. See Setup data at page 4.
CAUTION!
Do not use to much force, delicate sealing
surfaces can be damaged.
Spring preload
adjuster
Bike on a stand.
F1
R1
Bike on the ground.
F2
R2
Bike with rider on.
F3
R3
Set-up data:
Lenght 755 mm
Stroke 120 mm
Rebound adjustment 12 clicks
Compression adjustment 10 clicks
Spring preload 10 mm
Spring rate 9.5 N/mm
Oil level 85 mm
Checking sag and ride height
Front suspension
F1. Bike on a stand with the
suspension fully extended = ............
F2. Bike on the ground without rider = ............
F3. Bike on the ground with rider = ............
Free sag
F1 - F2 = ............
Ride height
F1 - F3 = ............
Rear suspension
R1.Bike on a stand with the
suspension fully extended = ............
R2.Bike on the ground without rider = ........... .
R3.Bike on the ground with rider = ............
Free sag
R1 - R2 = ............
Ride height
R1 - R3 = ............
NOTE!
If ride height is higher than recommended,
softer spring/springs must be used.
If ride height is lower than recommended,
harder spring/springs must be used.
Contact your Öhlins dealer for advice.
Öhlins Racing AB, Box 722, S-194 27 Upplands Väsby, Sweden.
Phone +46 8 590 025 00. Fax +46 8 590 025 80.
www.ohlins.com
Part No. FG 832. Issued 02 09 03
Before installation
Öhlins Racing AB can not be held responsible for
any damage whatsoever to front fork or vehicle,
or injury to persons, if the instructions for fitting
and maintenance are not followed exactly.
Similarly, the warranty will become null and void
if the instructions are not adhered to.
WARNING!
1. Installing a front fork, that is not approved by
the vehicle manufacturer, may affect the stability
of your vehicle. Öhlins Racing AB cannot be held
responsible for any personal injury or damage
whatsoever that may occur after fitting the front
fork. Contact an Öhlins dealer or other qualified
person for advice.
2. Please study and make certain that you fully
understand all the mounting instructions and
the owners manuals before handling this front
fork kit. If you have any questions regarding
proper installation procedures, contact an
Öhlins dealer or other qualified person.
3. The vehicle service manual must be referred
to when installing the Öhlins front fork
Safety signals
Important information concerning safety is
distinguished in this manual by the
following notations:
The Safety alert symbol means:
Caution! Your safety is involved.
WARNING!
Failure to follow warning instructions
could result in severe or fatal injury
to anyone working with, inspecting or
using the suspension, or to bystanders.
CAUTION!
Caution indicates that special pre-
cautions must be taken to avoid dam-
age to the suspension.
NOTE!
This indicates information that is of
importance with regard to procedures.
Öhlins products are subject to continual improve-
ment and development. Consequently, although
these instructions include the most up-to-date
information available at the time of printing, there
may be minor differences between your suspen-
sion and this manual. Please consult your Öhlins
dealer if you have any questions with regard to
the contents of the manual.
NOTE!
During storage and transportation, especially
at high ambient temperature, the oil and
grease used for assembling may run out
inside the packing and damage the expanded
polystyrene packing material. This is not
unusual and is in no way detrimental to the
front fork.
Kit contents
Before installing the front fork, please check the
contents of the kit, listed on the front page of
this instruction. If anything is missing, contact
your Öhlins dealer.
Description Pcs. Part No.
Fork legs (pair) 1 01676-07
Caliper bracket LH 1 01677-11
Caliper bracket RH 1 01677-12
Fender bracket Ring 2 01682-05
Fender bracket 2 01686-05
Fender bracket 1 01950-01
Fender bracket 1 01950-02
Bolt MC6S M4x14 4 01046-10
Screw MF6S M4x12 4 00382-04
Screw K6S M5x25 4 05323-02
Bolt MC6S M5x25 4 01046-19
Nut M5 DIN 985 4 00430-04
Shaft sleeve 22/30 1 01679-02
Shaft sleeve 27/30/44 1 01687-02
Washer 1 01952-01
Sticker Öhlins 2 00194-10
Owners Manual 1
18
15
18
WARNING!
1. It´s advisable to have an Öhlins dealer or other
qualified person to fit your front fork.
2. Instructions in the vehicle service manual are
to be followed when changing the front fork.
3. When working on a lifted vehicle it must be
securely supported to prevent it from falling.
Mounting instruction
1
Put the bike on a stand so the front wheel has
ground clearance. Make sure it´s steadily posi-
tioned and will not fall over.
2
Release the brake caliper on each side and let
them hange by the brake hoses.
3
Remove the fork wheel, by loosening and pull-
ing the shaft out.
4
Remove the front fender.
5
Release the fasternes of the front fork legs in the
lower triple clamps and loosen the screws on the
clip-on handlebars. Release the upper triple
clamps
6
Pull the fork legs out downwards and fit the Öhlin
front fork legs. Fit them to the triple clamps. Do
not tighten until the legs are in correct position,
see Note!
7
Tighten first the upper triple clamp than the lower
one to correct torque. Refit the clip-on handle-
bars. See the motorcycles Workshop manual.
9
Fit the brake caliper brackets with screws sup-
plied.
NOTE!
The fork legs are to be mounted so that the sec-
ond groove is just visible above the top edge of
the triple clamp.
CAUTION!
Do not overtighten. The legs can be deformed
and cause malfunction.
8
Fit the sleeve to the right fork bottom and the
bushing to the left fork bottom.
8
9
14
Fit the front fender.
15
Refit the wheel and the front wheel shaft. Fit the
washer (01952-01) supplied between the right
fork bottom and the shaft bolt. Do not tighten
yet.
16
Fit the brake calipers om both sides.
17
Lower the motorcycle. Brake the front wheel and
push the front suspension down, two or three
times. This will put the fork legs in a parallel po-
sition.
5 Nm
7 Nm
25 Nm
5 Nm
20 Nm
18
Tighten the wheel shaft and shaft clamps so the
fork legs are in fixed position.
19
Continue your work with Owners manual, sec-
tion Adjustments.
NOTE!
Another way is to rotate the wheel as fast as pos-
sible and bring it to a fast stop by braking. This
will bring the legs in correct position.
NOTE!
Make sure that all bolts are tightened to the cor-
rect torque and that nothing fouls or restricts
movement of the shock absorber when the sus-
pension is being fully compressed or extended.
Check with the Workshop manual of the mo-
torbike.
10
Fit the circlip model flexible fender bracket by
first pressing it over the lower fork leg.
11
Then open it slightly so it can be slided to the
fork bottom
12
Bolt the fender bracket to the brake caliper
bracket and fit the two forward fender brackets.
13
Fit the sticker to the fender bracket.
12
13
10
11
12
10 11
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Ohlins FG322 Mounting Instruction
-
-
-
-
-
-
-
-
-
