PURSUIT OS 315 Owner's manual

OS 315

Part Number 921287

August 2008

OS 315

OWNER’S MANUAL

FISHING BOATS

3901 St. Lucie Blvd.

Ft. Pierce, Florida 34946

Your Owner’s Manual was written to include

safety instructions to ensure safe operation

and maintenance of your boat. Safety alerts

symbols are used to alert potential personal

injury hazards.

All instructions are viewed from the stern look-

ing toward the bow, with starboard (to your

right) and port (to your left). A glossary of boat-

ing terms is included.

Your boat produces carbon monoxide (CO)

and uses flammable fuel. CO will cause

BRAIN DAMAGE or DEATH. Carbon monox-

ide gas (CO) is colorless, odorless and

extremely dangerous.

Every precaution has been taken by Pursuit

Fishing Boats to reduce the risks associated

with death, possible injury and damage from

fire or explosion. Your own precaution and

good maintenance procedures are necessary

in order to enjoy safe operation of your boat.

! DANGER

Indicates a hazardous situation which, if

not avoided, will result in death or seri-

ous injury.

! WARNING

Indicates a hazardous situation which, if

not avoided, could result in death or

serious injury.

! CAUTION

Indicates a hazardous situation which, if

not avoided, could result in minor or

moderate injury.

! NOTICE

Indicates a potentially hazardous situa-

tion which, if not avoided, may result in

property damage.

! DANGER

Exposure to carbon monoxide will

cause death or serious injury. Avoid

direct and prolonged exposure to CO.

Gasoline and other fuels are extremely

flammable and highly explosive under

certain conditions.

• DO NOT smoke or allow open flame

or sparks nearby when fueling.

• DO NOT block fuel vents.

• DO NOT store fuel in any containers

or compartments which are not des-

ignated for storing fuel.

Safety Information

Table of Contents

OS 315

Specifications.....................................1

Boat Information ................................ 9

Warranty and Warranty Registration

Cards ..............................................10

Federal Boat Safety Act .................. 10

Product Changes ............................10

Transferring the Warranty .............. 10

Owner/Operator Responsibilities ... 10

Propulsion Systems ..............1-1

1.1 General ............................................... 1-1

1.2 Saltwater Application ........................ 1-1

1.3 Engine Lubrication ............................ 1-2

1.4 Engine Cooling System ..................... 1-2

1.5 Propellers ........................................... 1-2

1.6 Engine Instrumentation ..................... 1-3

Helm Systems ........................2-1

2.1 General ............................................... 2-1

2.2 Helm Access ...................................... 2-1

2.3 Engine Throttle and Shift Controls .. 2-1

2.4 Neutral Safety Switch ........................ 2-2

2.5 Engine Power Tilt and Trim .............. 2-2

2.6 Engine Stop Switch ........................... 2-2

2.7 Automatic Fire Extinguisher System

(with Optional Generator) .............. 2-3

2.8 Steering System ................................. 2-3

2.9 Trim Tabs ............................................ 2-4

2.10 Compass ........................................... 2-5

2.11 Bow Thruster (Optional) .................. 2-5

2.12 Control Systems Maintenance ....... 2-5

Fuel Systems .........................3-1

3.1 General ............................................... 3-1

3.2 Fuel System ........................................ 3-1

3.3 Diesel Generator Fuel System

(Optional) ........................................ 3-3

3.4 Fueling Instructions ........................ 3-3

3.5 Fuel System Maintenance ............... 3-4

Electrical Systems ................4-1

4.1 General ................................................4-1

4.2 DC System ...........................................4-1

4.3 12-Volt DC Panels ...............................4-4

4.4 AC System .........................................4-6

4.5 AC Main Distribution ..........................4-7

4.6 Battery Charger Operation ................4-8

4.7 Shore Power Connection ...................4-8

4.8 Generator (Optional) ..........................4-9

4.9 Electrical System Maintenance .........4-9

Plumbing System ..................5-1

5.1 Fresh Water System ...........................5-1

5.2 Raw Water Washdown .......................5-2

5.3 Livewell ................................................5-3

5.4 Drainage ..............................................5-3

5.5 Plumbing System Maintenance .........5-5

Ventilation System ................6-1

6.1 Cabin Ventilation ................................6-1

6.2 Windshield Ventilation .......................6-1

6.3 Carbon Monoxide and Proper

Ventilation ........................................6-1

6.4 Bilge Compartment Ventilation .........6-1

6.5 Maintenance ........................................6-1

Exterior Equipment ...............7-1

7.1 Deck .....................................................7-1

7.2 Cockpit ................................................7-3

7.3 Tower (Dealer Installed) .....................7-5

Table of Contents

OS 315

Interior Equipment ................ 8-1

8.1 Companionway Door .........................8-1

8.2 Mid-Berth .............................................8-1

8.3 Head Compartment ............................8-1

8.4 Galley ...................................................8-2

8.5 Convertible V-Berth and Table ..........8-3

8.6 Carbon Monoxide Detector ...............8-3

8.7 Air Conditioner (Optional) .................8-3

8.8 Audio and Video Systems .................8-4

Safety Equipment .................. 9-1

9.1 General ................................................9-1

9.2 Engine Alarms ....................................9-1

9.3 Neutral Safety Switch .........................9-1

9.4 Engine Stop Switch ............................9-1

9.5 Automatic Fire Extinguishing System

(with Optional Generator) ...................9-2

9.6 Carbon Monoxide Hazards ................9-2

9.7 First Aid ...............................................9-5

9.8 Required Safety Equipment ..............9-5

9.9 Additional Safety Equipment ............9-8

Operation ............................. 10-1

10.1 General ............................................10-1

10.2 Homeland Security Restrictions ...10-1

10.3 Rules of the Road ...........................10-2

10.4 Pre-Cruise Check ...........................10-3

10.5 Operating your Boat .......................10-4

10.6 Fishing .............................................10-6

10.7 Tower Operation (Dealer

Installation) ...................................10-6

10.8 Docking, Anchoring and

Mooring .........................................10-7

10.9 Controls, Steering or Propulsion

System Failure .............................10-8

10.10 Collision .......................................10-9

10.11 Grounding, Towing and Rendering

Assistance ....................................10-9

10.12 Flooding or Capsizing .................10-9

10.13 Transporting your Boat ............10-10

10.14 Trailering your Boat ..................10-10

10.15 Water Skiing ..............................10-11

10.16 Man Overboard ..........................10-12

10.17 Trash Disposal ..........................10-12

Routine Maintenance ...........11-1

11.1 General ........................................... 11-1

11.2 Exterior Hull and Deck .................. 11-1

11.3 Seats, Upholstery, Canvas and

Enclosures ................................ 11-5

11.4 Cabin Interior ................................. 11-6

11.5 Bilge ............................................... 11-6

11.6 Generator (Optional) .....................11-6

Seasonal Maintenance ....... 12-1

12.1 Storage and Lay-up .......................12-1

12.2 Winterizing .....................................12-2

12.3 Recommissioning ......................... 12-4

APPENDIXES

Glossary of Terms .................A-1

Maintenance Schedule .........B-1

Maintenance Log ..................B-2

Boating Accident Report ......C-1

Float Plan ...............................D-1

Troubleshooting Guide ........E-1

Specifications

1

OS 315

Small Craft Owner's

Manual Supplement

OS 315

Boat Manufacturer/Model: Constructeur/Modèle du bateau: Modelo/Fabricante de la Embarcación:

Boothersteller/Model: Costruttore/modello della barca: Fabricante/Modelo do Barco:

Design Category: C-Inshore Propulsion Type: Tipo di propulsione:

Categorie de conception:

C-

à proximité de la côte

A

ntriebsart: Tipo de propulsión:

Categoria de Diseño: C-Costera Type de propulsion: Tipo propulsão:

Konstruktionskategorie: C-Küstennane

Gewässer

Outboard

Categoria di progetto:

C-Costeira

Categoria de Design:

C-Perto da Costa

Intended Use:

Verwendungszweck: Hull Identification Number:

HIN Label

Usage prévu: Rumpfunner:

Utilizzo previsto: Nemero d'identification de coque:

Uso previsto: Nemero identificazione scafo:

Utilização: Numero de Identificacion del Casco:

Recreation

Número de Identificação do Casco:

Maximum Recommended Load:

Charge maximale recommandée:

Carga Máxima recomendada:

1151 kg.

Empfohiene Beladung Maximum:

Carico massimo ammesso:

Carga Máxima Recomendada:

Recommended Number of Persons: Maximum Rated Engine Power:

Nombre de personnes recommandé: Puissance nominale maximale du moteur:

Número recomendado de personas: Potencia máxima del motor:

Empfohlene Personenanzahl: Maximale Motorleistung:

Omologazione al trasporto di n. persone: Massima potenza nominale motore:

Número de Pessoas Recomendado: Máxima potência nominal do motor:

9 373 kw.

Engine Installed, Manufacturer, Model and Number(s):

Moteur installé, Fabricant, modèle et numéros(s):

Motor instalado, Fabricante, modelo y numero(s):

Motor instaliert, Hersteller, modell, nummer(en):

1.

Motore istallato, Costruttore, modello e numero(s): 2.

Motor Instalado, Fabricante, Modelo e Número(s):

Mass of Craft (Approximate) With Largest Equipped Engine and permanently attached items,

Masses de Navire (Approximatives) plus full water and fuel, plus maximum recommended load:

Peso de la embarcación (aproximado) Avec le plus grand moteur équipé et systèmes en liaison

Gewicht des Bootes (Nährungswert) permanente, plus pleine charge d'eau et de carburant, plus

Massa dell'imbarcazione (approssimativa) charge maximale recommandée:

Massa da Embarcação (Aproximada) Con el mayor motor equipado y elementos permanentemente

With Largest Equipped Engine and instalados, más combustible y aqua, más la carga máxima recomendada:

permanently attached items: Mit größter Motorausführung und fest installiertem Inventar sowie

Avec le plus grand moteur équipé et vollen Wasser- und Kraftstofftanks und empfohlener Maximalbeladung:

systèmes en liaison permanente: Con il motore di maggiore cilindrata, attrezzature permanenti, più

Con el mayor motor equipado y elementos rifornimento di axqua e carburante e carco massimo ammesso:

permanentemente instalados: Com o maior motor instalado e os equipamentos permanentes, mais a

Mit größter Mororausführung und fest capacidade máxima de água e combustível, mais a carga máxima

installiert em Inventar: recomendada:

Con il motore di maggiore cilindrata e

6675

k

g

.

attrezzature permanenti: Trailerable Weight (engine, fuel and water, batteries and options):

Cim o maior motor instaldo e os Masse pour remorquage (moteur, carburant et eau, batteries et options):

epuipamentos permanentes: Peso remolcable (motor, combustible y agua, baterías y opciones):

4996

k

g

.

Auf Anhänger verladbares Gewicht (Motor, Kraftstoff und Wasser, Batterien

und Sonderausstattung):

Note:Information obtained from 2008 CE

Certificate and/or Specification Sheet

6/18/07 rev.D

Peso rimorchiabile su strada (motore, combustible e acgua, batterie ed

accessori):

Peso Rebocável (motor, combustível e água, baterieas e opções):

5910

k

g

.

2

Specifications

OS 315

Fuel Tank Capacity (0.73kg/Liter): 1075.06 Liters

Kraftstofftankkapazität

Fuel Type:

9

Gasoline

9

Diesel 1075.06 Liter

Oil Tank Capacity: N/A Liters Kraftstoffart:

9

Benzin

9

Diesel

Oil Type: 10-40

Öltankkapazität:

N/A Liter

Water Tank Capacity (1kg/Liter): 113.56 Liters

Ölsorte:

10-40

Holding Tank Capacity: 68.14 Liters Wassertankkapazität (1kg/Liter): 113.56 Liter

Speichertankkapazität: 68.14 Liter

Number and Type of Fire Extinguishers: Feuerlöscheranzahl und -typ:

Number and Type of CO Detectors: Rauchdetektoranzahl und -typ

N/A = Not Applicable n.z. = nicht zuttrefend

Contenance réservoir carburant

Capacità serbatoio carburante

(0,73kg/litre): 1075.06 litres (0,73kg/l): 1075.06 litri

Type de

carburant:

9

gasoil

9

diesel Tipo carburante:

9

Benzina

9

Diesel

Contenance réservoir d'huile: N/A litres

Capacità serbatoio olio:

N/A litri

Type d'huile: 10-40 Tipo oilio: 10-40

Contenance réservoir de'eau (kg/litre) 113.56 litres

Capacità serbatoio acqua (1kg/l):

113.56 litri

Contenance réservoir de rétention: 68.14

Capacità cassa di zavorra:

68.14 litri

Nombre et type d'extincteurs: Numbero e tipo di estintori:

Nombre et type de détecteurs de fumée: Nummero e tipo di rivelatori di esalazioni:

N/A = non applicable N/A = non pertinente

Capacidad del Depósito de Combustible Capacidade do Depósito de Combust

ível:

(73Kg/Litro): 1075.06 Litros (0,73kg/Litro): 1075.06 Litros

Tipo de

Combustible

9

Gasolina

9

Diesel Tipo de Combustível:

9

Gasolina

9

Gasóleo

Capacidad del Depósito de Aceite: N/A Litros

Capacidade do Depósito de Óleo:

N/A Litros

Tipo de Aceite: 10-40

Tipo de

Ó

leo:

10-40

Capacidad del Depósito de Agua

Capacidade do Depósito de Água:

(1Kg/Litro): 113.56 Litros (1kg/Litro): 113.56 Litros

Capacidad del Tanque de Retención:

68.14 Litros

Capacidade do Depósito Provisório:

68.14 Litros

Número y Tipo de Extintores de Incendios:

Número e Tipo de Extintores de Incêndio:

Número y Tipo de Detedtores de Humos:

Número e Tipo de Detectores de Fumo:

N/A = no aplicable N/A = Não Aplicàvel

OS 315

Small Craft Owner's

Manual Supplement

(2) A,B,C

(0,73 kg/Liter):

(2) A,B,C

22

(2) A,B,C

2

(2) A,B,C

EN

(2) A,B,C

2

FR IT

ES PT

DE

2.82

.4

3.25

9.97

10.64

.8

Specifications

3

OS 315

Locate and Identify: Localizar e identificar: Localizzazione e identificazione de

i

A

) Fuel Tank

A

) Depósito de Combustible componenti:

B) Fuel Tank Filling Poin

t

B) Punto de Carga del Depósito de

A

) Serbatoio carburante

C) O

il Tank

(

N

/

A

)

Combustible B) Bocchettone di riempimento

D

)O

il Tank Filling Point

(

N

/

A

)

C)

Depósito de Aceite

(

N

/

A

)

serbatoio carburante

E

)O

il Tank Emptying Poin

t

(

N

/

A

)

D) Punto de Carga del Depósito de

C) S

erbatoio olio

(

N

/

A

)

F) Water Tank

Aceite

(

N

/

A

)

D) Bocchettone di riempimento

G) Water Tank Filling Point

E

)

Punto de Descarga del Depósito

(

N

/

A

)

serbatoio olio

(

N

/

A

)

H) Holding Tank de Aceite

E

)S

carico serbatoio olio

(

N

/

A

)

I) Holding Tank Emptying Poin

t

F) Depósito de Agua F) Serbatoio acqua

J) Seacocks G) Punto de Carga del Depósito de G) Bocchettone di riempimento

K) Through-Hull Fittings Agua serbatoio acqua

L) Fire Extinguishe

r

H) Tanque de Tetención H) Cassa zavorra

M) Carbon Monoxide Detecto

r

I) Punto de Descarga del I) Scaric cassa zavorra

N) Escape Hatch Tanque de Tetención J) Valvole di presa acqua dal mare

O) Fire Escapes J) Válvula de Toma de Agua de Ma

r

K) Raccorderia passante nello scafo

P) Life Raft Stowage K) Accesorios Pasantes del Casco L) Estintore

Q) Safety Equipmen

t

L) Extintor de Incendios M) Rivelatore monossido di carbonio

R) Anchor Strong Points M) Detector de Monóxido de N) Boccaporto di sfuggita

S) Mooring Strong Points Carbono O) Uscite di sicurezza

T

)

Towing

S

trong Points

(

N

/

A

)

N) Escotilla de Seguridad P) Stivaggio zattera di salvataggi

o

O) Escalera de Incendios Q) Dotazioni di sicurezz

a

P) Almacenamiento de balsas R) Punti di attaco per l'ancoraggio

salvavidas S) Punti di attacco per l'ormeggio

Q) Equipos de seguridad

T

)

Punti di attacco per il traino

(

N

/

A

)

R) Puntos fuertes de anclaje

S) Puntos fuertes de amarre

T

)

Puntos

f

uertes de remolque

(

N

/

A

)

Small Craft Owner's

Manual Supplement

OS 315

EN ES IT

K

J

AA

AH

J

K K

F

N/OR/S

B

Diesel

I

G

R/S

B

J

Q

S

LL

L

M

AAF

L

Q

L

M

N/O

P

L

S

K

4

Specifications

OS 315

Small Craft Owner's

Manual Supplement

OS 315

Repèrez et identifiez: Position and Beschreibung: Localizar e Identificar:

A

) Réservoir de carburant

A

) Kraftstofftank

A

) Depósito de Conbustível

B) Point de remplissage réservoir B) Kraftstofftankfüllpunkt B) Ponto de Enchimento do Depósito de

de carburant

C)

Ö

ltank (n.z.)

Combustível

C) Réservoir d'huile (N/A) D)

Ö

ltankfüllpunkt (n.z.) C) Depósito de

Ó

leo (N/A)

D) Point de remplissage réservoir

E)

Ö

ltankablasspunkt (n.z.)

D) Ponto de Enchimento do Depósito de

d'huile (N/A)

F) Wassertank

Ó

leo (N/A)

E) Point de vindage réservoir G) Wassertankablasspunkt E) Ponto de Esvaziamento do Depósito

d'huile (N/A)

H) Speichertank

de

Ó

leo (N/A)

F) Réservoir d'eau I) Speichertankablaßpunkt F) Depósito de

Á

gua

G) Point de remplissage réservoir J) Flutventile G) Ponto de Enchimento do Depósito de

d'eau K) Rumpfdurchgangsanbauten

Á

gua

H) Réservoir de rétention L) Feuerlöscher H) Depósito Provisório

I) Point de vidange résevoir de M) Kohlenmonoxiddetektor I) Ponto de Esvaziamento do Depósito

rétention N) Notausstieg Provisório

J) Prises d'eau à la mer O) Reuerrettungswege J) Torneiras de tomada de àgua do mar

K) Raccords traversant la coque P) Rettungsfloßunterbringung K) Acessórios de Todo o Casco

L) Extincteur Q) Sicherheitsausrüstung L) Extintor de Incêndios

M) Détecteur de monoxyde de R) Ankerpunkte M) Detector de Monóxide de Carbono

carbone S) Vertäuungspunkte N) Escotilha de Fuga

N) Ecoutille d'évacuation

T) Abschlepppunkte (n.z.)

O) Saídas de Incêndio

O) Echelles de sauvetage P) Acondicionamento do Barco

P) Arrimage du radeau de Salva-vidas

sauvetage Q) Equipamento de Segurança

Q) Equipement de sécurité R) Pontos Fortes da Ancoragem

R) Points d'ancrage S) Pontos Fortes da Amaragem

S) Points d'amarrage

T) Pontos Fortes da Rebocagem (N/A)

T) Points de remorquage (N/A)

FR DE

PT

K

J

AA

AH

J

K K

F

N/OR/S

B

Diesel

I

G

R/S

B

J

Q

S

LL

L

M

AAF

L

Q

L

M

N/O

P

L

S

K

Specifications

5

OS 315

Working Deck Area OS315

11/21/2007

Working Deck

Areas for occupation during

normal operation of the boat

6

Specifications

OS 315

1/28/2008

Warning

Label

Locations

OS 315

Detail A

Helm Wing

Detail B

Port Transom

545175 Attached

to the ladder

545251

545355

Attached to the steering wheel

Detail C

Stbd Cockpit

Ste

p

Bas

e

545055

545450

545055

543775

Affixed to the bottom of the hatch

545449

Specifications

7

OS 315

1/28/2008

545519

545006

545012

545055

545369

545118

545365

Detail B

545118

Detail A

Detail of

Label

Locations

OS 315

545065

or

o

r

545126

545017

Detail C

545316

545055

545112

8

Specifications

OS 315

1/28/2008

545368

545011

Next to the cabin floor drain

Interior

Warning

Label

Locations

OS 315

543019

545368

545201

General Information

9

OS 315

Boat

Model: Hull Serial #:

Purchase Date: Delivery Date:

Ignition Keys # Registration #:

Draft: Weight:

Engine(s)

Make: Model:

Port Serial #: Starboard Serial #:

Transmission(s) (Inboard)

Make: Model:

Port Serial #: Starboard Serial #:

Ratio:

Outdrive(s) (Inboard/Outboard)

Make: Model:

Port Serial #: Starboard Serial #:

Propeller(s)

Make: Blades:

Diameter/Pitch: Other:

Generator

Make: Model:

Serial #: kW

Dealer Pursuit

Name: Phone:

Dealer/Phone: Representative:

Salesman: Address:

Service Manager:

Address:

Boat Information

Fill out the following information and leave it in your PURSUIT Owner’s Manual. This

information will be important for you and PURSUIT service personnel to know, if and

when you may need to call PURSUIT for technical assistance or service.

PURSUIT Fishing Boats reserves the right to make changes and improvements in

equipment, design and vendor supplied equipment at any time without notification.

10

General Information

OS 315

Warranty and Warranty

Registration Cards

The PURSUIT Limited Warranty Statement

is included with your boat. It has been writ-

ten to be clearly stated and easily under-

stood. If you have any questions after

reading the warranty, please contact PUR-

SUIT Customer Relations.

PURSUIT, engine manufacturers, and the

suppliers of major components maintain

their own manufacturer's warranty and ser-

vice facilities. It is important that you prop-

erly complete the warranty registration cards

included with your boat and engine(s) and

mail them back to the manufacturers to reg-

ister your ownership. This should be done

within 15 days of the date of purchase and

before the boat is put into service. A form for

recording this information is provided at the

beginning of this manual. This information

will be important for you and service person-

nel to know, if and when you may need ser-

vice or technical information.

The boat warranty registration requires the

Hull Identification Number “HIN” which is

located on the starboard side of the transom,

just below the rub rail. The engine warranty

registration requires the engine serial num-

ber(s). Please refer to the engine owner's

manual for the location of the serial num-

ber(s).

Federal Boat Safety Act

All boat manufacturers are required by the

Federal Boat Safety Act of 1971 to notify first

time owners in the event any defect is dis-

covered “which creates a substantial risk of

personal injury to the public.” It is essential

that we have your warranty registration card

complete with your name and mailing

address in our files so that we can comply

with the law if it should become necessary.

Product Changes

PURSUIT is committed to the continuous

improvement of our boats. As a result, some

of the equipment described in this manual or

pictured in the catalog may change or no

longer be available.

PURSUIT reserves the right to change

standard equipment, optional equipment

and specifications without notice or obli-

gation. If you have questions about the

equipment on your PURSUIT, please con-

tact PURSUIT Customer Relations.

Transferring the Warranty

For a Transfer fee, S2 Yachts will extend

warranty coverage to subsequent owners of

PURSUIT models for the duration of the

original warranty period. Please refer to the

PURSUIT Limited Warranty Statement for

the procedure to transfer the warranty. To

take advantage of this program, notification

of the change of ownership, including the

new owner's name, address and telephone

number together with the appropriate fee,

must be sent to PURSUIT Fishing Boats,

Customer Relations Department, 3901 St.

Lucie Boulevard, Ft. Pierce, Florida 34946,

within 30 days of the date of resale.

S2 Yachts will confirm, in writing, that the

transfer of the warranty has taken place.

After which, the transferee will be treated as

the original purchaser as outlined in the

PURSUIT Limited Warranty Statement.

Owner/Operator

Responsibilities

Registration and Documentation

Federal law requires all undocumented ves-

sels equipped with propulsion machinery be

registered in the state of principal use. A cer-

tificate of documentation will be issued upon

registration. These registration numbers

must be displayed on your boat. The owner/

operator of a boat must carry a valid certifi-

cate of registration whenever the boat is in

use. When moved to a new state of principal

use, the certificate is valid for 60 days.

In order to be valid, the numbers must be

installed to the proper specifications. Check

with your dealer or state boating authority for

numbering requirements. The Coast Guard

issues the certificate of number in Alaska; all

others are issued by the state.

General Information

11

OS 315

Insurance

In most states the boat owner is legally

responsible for damages or injuries the boat

causes. Responsible boaters carry ade-

quate liability and property damage insur-

ance for their boat. You should also protect

the boat against physical damage and theft.

Some states have laws requiring minimum

insurance coverage. Contact your dealer or

state boating authority for information on the

insurance requirements in your boating

area.

Reporting Boating Accidents

All boating accidents must be reported by

the owner or operator of the boat to the

proper marine law enforcement authority for

the state in which the accident occurred.

Immediate notification is required if a person

dies or disappears as a result of a recre-

ational boating accident.

If a person dies or there are injuries requir-

ing more than first aid, a formal report must

be filed within 48 hours.

A formal report must be made within 10 days

for accidents involving more than $500.00

damage or the complete loss of a boat.

A "Boating Accident Report" form is located

near the back of this manual to assist you in

reporting an accident. If you need additional

information regarding accident reporting,

please call the Boating Safety Hotline, 800-

368-5647 or uscgboating.org.

Education

If you are not an experienced boater, we rec-

ommend the boat operator and other people

that normally accompany the operator, enroll

in a boating safety course. Organizations

such as the U.S. Power Squadrons, United

States Coast Guard Auxiliary, State Boating

Authorities and the American Red Cross

offer excellent boating educational pro-

grams. These courses are worthwhile even

for experienced boaters to sharpen your

skills or bring you up to date on current rules

and regulations. They can also help in pro-

viding local navigational information when

moving to a new boating area. Contact your

dealer, State Boating Authority or the Boat-

ing Safety Hotline, 800-368-5647 or uscg-

boating.org for further information on boating

safety courses.

Required Equipment

U.S. Coast Guard regulations require certain

equipment on each boat. The Coast Guard

also sets minimum safety standards for ves-

sels and associated equipment. To meet

these standards some of the equipment

must be Coast Guard approved. “Coast

Guard Approved Equipment” has been

determined to be in compliance with USCG

specifications and regulations relating to

performance, construction or materials. The

equipment requirements vary according to

the length, type of boat, and the propulsion

system. Some of the Coast Guard equip-

ment is described in the Safety Equipment

Section of this manual. For a more detailed

description, obtain “Federal Requirements

and Safety Tips for Recreational Boats” by

contacting the Boating Safety Hotline 800-

368-5647, uscgboating.org or your local

marine dealer or retailer.

Some state and local agencies go beyond

USCG regulations or impose similar equip-

ment requirements on waters that do not fall

under Coast Guard jurisdiction. Contact your

dealer or local boating authority, they can

provide you with additional information for

the equipment requirements for that boating

area.

12

Operator Notes

OS 315

Propulsion Systems

1-1

Section 1

OS 315

Propulsion Systems

1.1 General

Your Pursuit boat is designed to be powered

with twin 2-cycle or 4-cycle outboard

engines.

Each manufacturer of the various outboard

engines provides an owner’s information

manual which includes its limited warranty

statement with its product. It is important you

read and understand the information and

become familiar with the warranty, operation

and maintenance of the engines and drive

systems. A warranty registration card has

been furnished with each new engine and

can be located in the engine owner’s man-

ual. All information requested on this card

should be filled out completely by the dealer

and purchaser and returned to the respec-

tive engine manufacturer as soon as possi-

ble.

1.2 Saltwater Application

Each outboard engine is a complete drive

system with the gear case (transmission),

forward of the propeller and connected to

the power head with a vertical drive shaft.

Other than the routine maintenance outlined

in the engine owner’s manual, there is little

to be concerned with unless the boat is to be

kept in saltwater for extended periods.

Marine growth will occur when components

are left in the water for extended periods and

can cause poor performance or permanent

damage to the exposed components. The

type of growth and how quickly it occurs is

relative to the water conditions in your boat-

ing area. Water temperature, pollution, cur-

rent, etc. can have an effect on marine

growth.

Galvanic corrosion is the corrosion process

occurring when different metals are sub-

merged in an electrolyte. Sea water is an

electrolyte and submerged engine compo-

nents must be properly protected. Outboard

engines are equipped with sacrificial anodes

to help prevent galvanic corrosion problems.

The anodes must be monitored and

replaced as necessary. For locations and

maintenance, refer to the engine owner’s

manual.

When leaving the boat in the water, tilt the

motors as high as possible to decrease the

risk of marine growth around the cooling

inlets, propeller and exhaust ports and dam-

age from galvanic corrosion.

! NOTICE

DO NOT attempt to service any part of

the outboard or boat systems unless

you are familiar or qualified to do so.

Do not use parts which are not

designed for a marine application.

! WARNING

MOVING PARTS HAZARD.

Contact with moving parts can entan-

gle, cut and cause death or serious

injury. DO NOT get close enough to

make contact with any running

machinery moving parts, i.e., engine

or propeller. Contact can result in loss

of body parts, strangulation, burns

and/or severe loss of blood resulting

in death or serious injury.

! NOTICE

Use only the fuel recommended by the

engine manufacturer. Use of old, con-

taminated fuel can cause the engine

to malfunction or severe damage.

1-2

Section 1 Propulsion Systems

OS 315

1.3 Engine Lubrication

4-cycle engines have an oil sump in the

crankcase. The oil type, grade and level

must be followed in accordance with the

engine manufacturer’s recommendation. It is

normal for 4-cycle engines to consume a

small amount of oil. Check the oil level

before each use and change it following the

engine manufacturer’s recommendation.

2-cycle outboard engines are lubricated by

an oil injection system. Check the oil level

before each use and use only type specified

by the engine manufacturer. Also monitor

the oil level by checking the gauge in the

helm or visually checking the oil level, in the

tank by using the reference marks on the

tanks. Refer to the engine owner’s manual

for oil specifications and additional informa-

tion on the oil injection system. Refer to the

Fuel System Section.

1.4 Engine Cooling System

Outboard engines are raw water (sea water)

cooled. Water is pumped through the water

inlets, circulated through the engine block,

and expelled with the exhaust through

exhaust port, water port and the propeller

hub. The water pump uses a small impeller

made of synthetic rubber. The impeller and

water pump cannot run dry for more than a

few seconds. In most outboard engines,

some cooling water is diverted through ports

below the engine cowling. This allows the

operator to visually check the operation of

the cooling system. When the engine is

started, make sure a steady stream of water

is present.

If the boat is used in salt or badly polluted

water, flush the engines after each use to

reduce corrosion. Refer to the engine

owner’s manual for the proper engine flush-

ing procedure.

1.5 Propellers

The propellers convert the power of the

engines into thrust. Propellers vary in style,

diameters and pitch. The best set for your

needs will depend on your application and

expected average load. Propeller sizes are

identified by two numbers stamped on the

prop in sequence; the first is the diameter

and the second is the pitch (example 14 x

21). Pitch is the theoretical distance the pro-

peller will travel in one rotation. Repair or

replace a propeller immediately if it has been

damaged. A damaged propeller can cause

! CAUTION

DO NOT use copper-based coatings or

any coatings not approved for use

with aluminum. Some paint manufac-

turers claim their paints are safe for

aluminum. Copper components and

copper-based paints can cause severe

corrosion to aluminum. DO NOT use

copper-based paints.

Mercury or mer-

cury-based compounds that come

into contact with aluminum will result

in severe corrosion.

! NOTICE

Use only the oil recommended by the

engine manufacturer, and monitor the

oil level. Use of any other type of oil

can cause the engine to malfunction

or severe damage.

! CAUTION

DO NOT operate an engine out of the

water, even momentarily. Water must

be supplied to the cooling system of

the power head and water pump, or

serious damage will result. If it is nec-

essary to run the engine out of the

water, connect it to a engine flush

attachment design for your specific

engine.

Propulsion Systems

1-3

Section 1

OS 315

vibration that can be felt in the boat and can

damage the engine gear case. Refer to the

engine owner’s manual for information on

propeller removal and installation.

1.6 Engine Instrumentation

The helm station is equipped with a set of

engine instruments and alarms. The instru-

ments allow the operator to monitor the

operational conditions of the engines. Moni-

toring the instrumentation allows the opera-

tor to operate the engines most efficiently

and prevent serious costly damage. The

instrumentation is unique to the type of out-

board engines installed on your Pursuit.

Your boat may not be equipped with all of

the following gauges.

Some models may be equipped with

Yamaha Command Link Integrated Infor-

mation System®. Refer to the Yamaha

manuals for information on the operation

of this system.

Tachometer

The tachometer displays the speed of the

engine in revolutions per minute (RPM). This

speed is not the boat speed or the speed of

the propeller. The tachometer may not regis-

ter zero with the key in the “OFF” position.

Speedometer

The speedometer indicates the speed of the

boat in miles per hour (MPH). Most speed-

ometers measure the water pressure

against a small hole in a pick-up tube

located in the gear case or mounted on the

bottom of the transom.

Temperature Warning

The temperature warning indicates the tem-

perature of the engine. A sudden increase in

the temperature could indicate an obstructed

water inlet or an impeller failure.

Fuel Gauge

The fuel gauge indicates the approximate

fuel level in the fuel tanks. This gauge is a

relative indication of the fuel supply avail-

able; it is not a calibrated instrument. On

Yamaha equipped boats, fuel level is dis-

played in the speedometer.

Voltmeter

The voltmeter displays the voltage for the

battery and the charging system. The nor-

mal voltage is 11 to 12 volts with the

engine(s) off and 13 to 14.5 volts with the

engine(s) running.

Hourmeter

The hourmeter keeps a running total of

engine hours while operating.

Tilt/Trim Gauge

The tilt/trim gauge monitors the position of

the outboard engine. The upper range of the

gauge indicates the tilt, which is used for

shallow water operation, trailering and to

keep the gear case out of the water. The

lower range indicates the trim position. Trim

is used to adjust the hull angle while operat-

ing your boat on plane. Refer the engine

owner’s manual for more information on the

operation of the outboard power tilt and trim.

! NOTICE

DO NOT exceed maximum recom-

mended engine RPM. Exceeding,

maintaining or close to maintaining

maximum can reduce engine life.

! NOTICE

Continued operation of an overheated

engine will cause severe engine dam-

age. If the engine overheats, shut off

the engine, investigate the problem

and correct it.

1-4

Section 1 Propulsion Systems

OS 315

Engine Alarms

Most outboards are equipped with an audi-

ble alarm system mounted in the helm area

to monitor selected critical engine systems

and functions. The alarm will sound if one of

these systems begins to fail. Refer to the

engine owner’s manual for information on

the alarms installed with your engines.

Fuel Management

Fuel management systems are standard

equipment with some outboard engines. On

Yamaha® engines, the fuel management

gauge is a multifunction gauge used to mon-

itor fuel consumption of the engines. If your

boat is equipped with this system, refer to

the engine or fuel management manual.

Instrument Maintenance

Electrical system, instruments and ignition

circuitry are protected by a circuit breaker or

fuse located on the engine. The ignition

switches and all instruments, controls, etc.

must be protected from the weather when

not in use. Excessive exposure can lead to

gauge and ignition switch failures.

Moisture may fog the inside of the gauge

lens. Turning the gauge lights on will help

dry the lenses. Fogging will normally not

harm the gauges, but if the fogging contin-

ues and moisture accumulates, the excess

water can damage the gauges. The gauges

are designed with drain holes to reduce the

accumulation of moisture. Make sure that if

a gauge is removed, it is reinstalled with the

drain holes in the proper position.

! CAUTION

If an engine alarm sounds, shut off the

engine, investigate the problem and

correct it.

Page is loading ...

PURSUIT OS 315 Owner's manual

This manual is also suitable for

PURSUIT OS 315 Owner's manual

Related papers

Other documents