Chief FCA650S Installation guide

FCA650S
Chief
Brand
Chief
Model
FCA650S
Category
Mounting kits
Type
Installation guide

This manual is also suitable for

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
CPU Holder for Fusion™ Cart/Stand
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCA650/651
FCA650/651 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the CPU holder does not
exceed 25 lbs (11.34 kg) for the FCA650 or 10 lbs (4.5 kg) for
the FCA651.
WARNING: Use this mounting system only for its intended
use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
WARNING: Never operate this mounting system if it is
damaged. Return the mounting system to a service center for
examination and repair.
WARNING: Do not use this product outdoors.
WARNING: RISK OF INJURY TO PERSONS! Do not
place video equipment such as televisions or computer
monitor on CPU holder.
--SAVE THESE INSTRUCTIONS--
Installation Instructions FCA650/651
3
DIMENSIONS
5.40
137.1
0.38
9.5
157.5
6.20
88.9
3.50
16.00
406.4
SECURITY HOLE FOR
5/16" DIAMETER PAD LOCK
INTERNAL SLOTS
FOR TIE DOWN STRAPS
PANEL NOT SHOWN FOR CLARITY
15.00
381.0
MAX CPU LENGTH
565.0
22.24
15.00
381.0
MAX CPU HEIGHT
5.13
130.2
MAX CPU WIDTH
FCA650
PANEL NOT SHOWN FOR CLARITY
10.00
254.0
MAX CPU LENGTH
399.9
15.74
10.00
254.0
MAX CPU HEIGHT
3.63
92.1
MAX CPU WIDTH
3.90
99.0
0.38
9.5
88.9
3.50
11.00
279.4
SECURITY HOLE FOR
5/16" DIAMETER PAD LOCK
INTERNAL SLOTS
FOR TIE DOWN STRAPS
FCA651
FCA650/651 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions FCA650/651
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
5/32" (security) (included)
3/16" (included)
1/8" (included)
B (1)
[adapter bracket]
C (1)
[accessory bracket]
E (2)
1/4-20 x 3/8"
F (1)
1/4-20 x 3/8"
A (1)
[CPU holder]
D (4)
5/16-18 x 1/2"
G (1)
3/16"
H (1)
5/32" (security)
J (1)
1/8"
(FCA651 shown)
FCA650/651 Installation Instructions
6
Assembly And Installation
NOTE: The following procedure assumes the Fusion Cart/
Stand has already been completely assembled.
IMPORTANT ! : The FCA650/651 has been designed
specifically for Chief’s Fusion™ Series Carts and Stands.
DO NOT attempt to install this CPU holder onto any other
cart or stand!
1. Remove back cover from cart/stand. (See Figure 1)
2. Remove column inner cover from cart/stand. (See Figure 1)
3. Remove side cover from cart/stand by sliding it up the side
channel on the side where the CPU holder will be installed.
(See Figure 1)
Figure 1
4. Partially install 1/4-20 x 3/8" set screw (F) into accessory
bracket (C). (See Figure 2)
5. Slide accessory bracket (C) with set screw into side channel
where CPU holder will be installed. (See Figure 2)
Figure 2
6. Slide accessory bracket up or down in side channel until
desired mounting height is reached. (See Figure 3)
7. Tighten set screw (F) to lock bracket in position. (See Figure
3)
8. Use two 1/4-20 x 3/8" button head cap screws (E) to secure
adapter bracket (B) to accessory bracket (C). (See Figure 3)
Figure 3
(display not shown for clarity)
2
2
3
1
1
side covers
column inner
cover
back cover
(display not shown for clarity)
(C)
(F)
4
5
(B)
(E) x 2
8
6
7
Installation Instructions FCA650/651
7
9. Use 5/32" security hex key (H) to remove two security
screws holding side panel to CPU holder (A). (See Figure 4)
10. Slide side panel up to remove it from CPU holder. (See
Figure 4)
Figure 4
11. Use four 5/16-18 x 1/2" button head cap screws (D) to
secure CPU holder (A) to adapter bracket (B). (See
Figure 5)
Figure 5
12. Install CPU to CPU holder.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the CPU holder does not
exceed 25 lbs (11.34 kg) for the FCA650 or 10 lbs (4.5 kg) for
the FCA651.
13. Replace side panel back into its original position on CPU
holder (A). (See Figure 6)
14. Use security screws (removed in Step 9) to reattach side
panel to CPU holder (A). (See Figure 6)
15. (Optional) Use padlock (not provided) to provide further
security to CPU holder. (See Figure 6)
Figure 6
16. Reinstall back cover to cart/stand.
17. Reinstall inner column cover to cart/stand.
Adjustments
Height Adjustment
1. Remove side panel and CPU from CPU holder (A).
2. Loosen set screw (F). (See Figure 7)
3. Loosen two button head cap screws (E). (See Figure 7)
4. Adjust height as desired.
5. Tighten two button head cap screws (E). (See Figure 7)
6. Reinstall CPU and side panel to CPU holder.
Figure 7
9
side panel
(A)
10
10
(B)
11
(D) x 4
(A)
14
15
13
13
2
3 5
4
FCA650/651 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P 800.582.6480 / 952.225.6000
F 877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P +31 (0) 495 580 852
F +31 (0) 495 580 845
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002263 Rev01
2012 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
11/12
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief FCA650S Installation guide

FCA650S
Chief
Brand
Chief
Model
FCA650S
Category
Mounting kits
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents