SwitchBlade x8106 Chassis Switch and AT-SBx81CFC960 Card Installation Guide
11
Figure 110: Removing the Dust Cover from an SFP+ Transceiver in the AT-SBx81CFC960 Controller Fabric Card...... 169
Figure 111: Positioning the Handle on the Transceiver..................................................................................................... 169
Figure 112: Attaching a Fiber Optic Cable to an SFP+ Transceiver in the AT-SBx81CFC960 Controller Fabric Card..... 170
Figure 113: AC Sockets on the Rear Panel of the AT-SBx8106 Chassis.......................................................................... 173
Figure 114: Connecting the AC Power Cord for the AT-SBxPWRSYS1 AC Power Supply.............................................. 174
Figure 115: Securing the Power Cord for the AT-SBxPWRSYS1 AC Power Supply to an Anchor................................... 175
Figure 116: Connecting the AC Power Cord for the AT-SBxPWRPOE1 Power Supply.................................................... 176
Figure 117: Securing the Power Cord for the AT-SBxPWRPOE1 Power Supply to an Anchor........................................ 177
Figure 118: Dress and Secure AC Power Cords............................................................................................................... 178
Figure 119: Components of the AT-SBxPWRSYS1 DC Power Supply............................................................................. 180
Figure 120: Grounding Wire Terminal ............................................................................................................................... 181
Figure 121: Stripping the Stranded Grounding Wire.......................................................................................................... 181
Figure 122: Attaching the Stranded Grounding Wire to the Grounding Terminal.............................................................. 181
Figure 123: Removing the Nut and Washer from the Grounding Post.............................................................................. 182
Figure 124: Installing the Grounding Wire......................................................................................................................... 183
Figure 125: Stripping the solid or Stranded Grounding Wire............................................................................................. 184
Figure 126: Attaching the Bare Grounding Wire to the Grounding Post............................................................................ 184
Figure 127: Securing the Bare Grounding Wire to the Grounding Post............................................................................. 185
Figure 128: Power Wire Terminals.................................................................................................................................... 186
Figure 129: Stripping the Power Wires.............................................................................................................................. 187
Figure 130: Attaching the Power Wires to the Straight Terminal Lugs.............................................................................. 187
Figure 131: On/Off Switch on the AT-SBxPWRSYS1 DC Power Supply.................................................................
......... 188
Figure 132: Opening the Plastic Cover.............................................................................................................................. 189
Figure 133: Removing the Terminal Screws...................................................................................................................... 190
Figure 134: Connecting the Positive (+) Power Wire with a Straight Terminal.................................................................. 191
Figure 135: Connecting the Negative (-) Power Wire with a Straight Terminal................................................................. 192
Figure 136: Closing the Plastic Cover over the Terminal Connectors............................................................................... 193
Figure 137: Tightening the Handle Locking Screw............................................................................................................ 194
Figure 138: Stripping the Power Wires.............................................................................................................................. 195
Figure 139: Attaching the Power Wires to the Right Angle Terminals............................................................................... 195
Figure 140: Removing the Plastic Cover........................................................................................................................... 196
Figure 141: Removing the Terminal Screws...................................................................................................................... 197
Figure 142: Connecting the Positive (+) Power Wire with a Right Angle Terminal............................................................ 198
Figure 143: Connecting the Negative (-) Power Wire with a Right Angle Terminal........................................................... 199
Figure 144: Tightening the Handle Locking Screw............................................................................................................ 200
Figure 145: Stripping Solid or Stranded DC Power Wires................................................................................................. 201
Figure 146: Connecting the Positive Lead Wire ................................................................................................................ 202
Figure 147: Connecting the Negative Lead Wire............................................................................................................... 203
Figure 148: Switch Initialization Messages........................................................................................................................ 206
Figure 149: Switch Initialization Messages (Continued).................................................................................................... 207
Figure 150: Connecting the Management Cable to the Console RS-232 Port.................................................................. 212
Figure 151: SHOW VERSION Command.......................................................................................................................... 213
Figure 152: SHOW CARD Command................................................................................................................................ 214
Figure 153: Disconnecting the AC Power Cord from the AC Socket on the Back Panel................................................... 232
Figure 154: Lifting the Locking Handle on the Power Supply............................................................................................ 233
Figure 155: Removing the Power Supply from the Chassis.............................................................................................. 234
Figure 156: Installing a Blank Power Supply Slot Cover ................................................................................................... 235
Figure 157: Lowering the Locking Handle on the Power Supply Slot Cover.........................................................
............ 236
Figure 158: Loosening the Screw on the Locking Handle................................................................................................. 237
Figure 159: Opening the Plastic Window on the Terminal Block....................................................................................... 238
Figure 160: Removing the Negative Lead Wire................................................................................................................. 239
Figure 161: Removing the Positive Lead Wire from the Terminal Block ........................................................................... 240
Figure 162: Reinstalling the Screws on the Positive and Negative Terminals................................................................... 241
Figure 163: Closing the Plastic Cover ............................................................................................................................... 242
Figure 164: Removing the Grounding Wire....................................................................................................................... 243
Figure 165: Reinstalling the Nut and Washer on the Grounding Post............................................................................... 244
Figure 166: Lifting the Locking Handle and Removing the Power Supply......................................................................... 245
Figure 167: Installing a Blank Power Supply Slot Cover ................................................................................................... 246
Figure 168: Lowering the Locking Handle on the Power Supply Slot Cover..................................................................... 247
Figure 169: Loosening the Screw on the AT-SBxFAN06 Fan Module .............................................................................. 254