Hitachi VM-E625LA User manual

Brand: Hitachi

Model: VM-E625LA

Category: Camcorders

Type: User manual

This manual is also suitable for

VME-625LA - Camcorder

For Your Safety - 1 -

Instruction Manual

8mm Video Camcorder

VM-E625LA

Hitachi Home Electronics (America), Inc. HITACHI (HSC) CANADA INC

3890 Steve Reynolds Blvd., Norcross, GA 30093 3300 Trans Canada Highway, Pointe Claire,

Tel. 770-279-5600 Quebec, H9R 1B1, CANADA

Tel. 514-697-9150

HITACHI SALES CORPORATION OF HAWAII, INC

3219 Koapaka Street, Honolulu, Hawaii 96819

Tel. 808-836-3621

Thank you for buying a Hitachi product. Please take time to become familiar with the manual and how it is set up.

Keep it handy for feature reference.

QR15092 © Hitachi, Ltd. 1996 Printed in Japan KR-R(N)

For Your Safety - 2 -

TABLE OF CONTENTS

For Your Safety.........................................................................................................................................3

IMPORTANT SAFEGUARDS.................................................................................................................4

IMPORTANT SAFETY INSTRUCTIONS FOR AC ADAPTER/CHARGER....................................7

Read This First..........................................................................................................................................7

Before You Begin .....................................................................................................................................8

Features.................................................................................................................................................8

Components and Accessories............................................................................................................8

Optional RF Adapter............................................................................................................................9

Attaching the Shoulder Strap..............................................................................................................9

Lens Cap................................................................................................................................................9

Getting Started........................................................................................................................................10

Charging the Battery..........................................................................................................................10

Adjusting the Electronic Viewfinder.................................................................................................12

Eyepiece Adjustment.........................................................................................................................12

Adjustment the Hand Strap...............................................................................................................12

Loading Batteries................................................................................................................................13

Using Alternative Power Sources....................................................................................................17

Inserting and Removing Cassettes..................................................................................................18

Using the Linear Time Counter........................................................................................................19

Remaining Tape .................................................................................................................................19

Setting the Date and Time................................................................................................................20

Getting Started, Identifying Controls ...................................................................................................21

Basic Techniques...................................................................................................................................25

Making a Basic Recording................................................................................................................25

Playback...............................................................................................................................................25

Playing Back Your Recording on Your TV .....................................................................................27

Advanced Techniques...........................................................................................................................28

Changing the Angle of the LCD Monitor when Recording...........................................................28

Date Recording...................................................................................................................................29

Using the Power Zoom......................................................................................................................30

Using the Digital Zoom ......................................................................................................................31

Using the INST. ZOOM (Instant Zoom) Button..............................................................................31

Using Auto Focus...............................................................................................................................32

Using Manual Focus..........................................................................................................................33

Using the Electronic Image Stabilizer .............................................................................................33

Using Fade ..........................................................................................................................................34

Using 16x9...........................................................................................................................................35

Using Instant Review.........................................................................................................................35

Using Quick Edit.................................................................................................................................35

Using Macro ........................................................................................................................................36

Date Search.........................................................................................................................................36

Using Memory.....................................................................................................................................37

Using the Display Button...................................................................................................................37

Using the Wireless Remote Control................................................................................................38

Creating and Recording A Title........................................................................................................38

Dubbing from the camcorder to a VCR...........................................................................................40

Using Synchro Edit.............................................................................................................................40

For Your Safety - 3 -

Simple Programmable Edit (Edit remote control is optional accessory)....................................41

Controlling Your TV with the Camcorder's Remote Control........................................................44

Using Audio/Video Dubbing..............................................................................................................45

Recording Television Programs.......................................................................................................45

Attaching the Optional Wide or Tele Converter Lens...................................................................46

Attaching the Optional DC Camera Light .......................................................................................46

General Maintenance.............................................................................................................................48

Cleaning the camcorder Heads........................................................................................................48

Cleaning the Lens and Picture Tube of the Electronic Viewfinder .............................................48

Periodic Maintenance........................................................................................................................49

Troubleshooting..................................................................................................................................49

Specifications......................................................................................................................................52

Accessories Add Excitement................................................................................................................53

Available Accessories........................................................................................................................53

More Available Accessories..............................................................................................................53

To Order in the United States...........................................................................................................53

For Your Safety

The CAM/OFF/VIDEO switch turns the camcorder on and off, leaving the date/time feature unaffected. If the unit

is to be left unattended for a long period of time, turn the camcorder off and attach the lens cap.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

The camcorder and AC adapter/charger have the following caution marks.

Identifications of caution marks

This symbol warms the user that uninsulated voltage within the unit may have sufficient magnitude to

cause electrical shock. Therefore, it is dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the operation and maintenance of

this unit has been included. Therefore, it should be read carefully to avoid any problems.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT OPEN.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

AND FULLY INSERT PLUG.

WARNING: Many television programs and films are copyrighted. In certain circumstances, copyright law may

apply to private in-home videotaping of copyrighted materials.

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

The liquid crystal display (LCD) panel is made by highly precise technology. More than

99.99% of its picture elements (pixels) are effective, but some (less than 0.01%) may appear

IMPORTANT SAFEGUARDS - 4 -

as colored bright dots. This does not indicate a fault as the LCD panel stretches the limits of

current technology.

Warning: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant of Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct by one or

more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Caution to the user: Changes or modifications not expressly approved by the manufacture could void the

user's authority to operate the equipment.

"Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to

Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the

cable ground shall be connected to the grounding system of the building, as close to the point of cable entry

as practical".

Notes:

• This unit uses 8mm video format cassettes.

• It records and plays back in the SP mode (14.3 mm/sec).

• It cannot record and play back in the LP mode (7.2 mm/sec).

• This camcorder uses a Hi-Fi stereo sound system. When a tape recorded by this camcorder is played by a

conventional 8mm camcorder, monaural sound is output. When a tape recorded by a conventional 8mm

camcorder is played by this machine, monaural sound is output.

MOISTURE

Avoid operating your camcorder immediately after moving it from a cold place to a

warm, humid place. Give the camcorder 2 to 3 hours to stabilize in the ambient

conditions of the surroundings before inserting a cassette. When moved from a cold

place to a warm, humid place, moisture may condense on the head drum inside the

machine. This moisture could cause the tape to stick to the headwheel and damage the

headwheel or tape.

When a small amount of moisture is sensed, "TAPE" flashes in the viewfinder. Remove

the cassette and set the CAM/OFF/VIDEO switch to OFF, then wait for about one hour.

IMPORTANT SAFEGUARDS

In addition to the careful attention devoted to quality standards in the manufacture of your video product, safety is

a major factor in the design of every instrument. But, safety is your responsibility too.

This page lists important information that will help to assure your enjoyment and proper use of a Video camcorder

and accessory equipment. Please read it carefully before operating your video product and keep it in a handy

place for future reference.

INSTALLATION

1 Read and Follow Instructions -- All the safety and operating instructions should be read before the video

product is operated. Follow-all operating and use instructions.

IMPORTANT SAFEGUARDS - 5 -

2 Retain Instructions -- The safety and operating instructions should be retained for future reference.

3 Heed Warnings -- Comply with all warnings on the video product and in the operating instructions.

4 Polarized Plug -- This video product is equipped with a polarized alternating-current line plug (a plug having

one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you

are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your

electrician to replace your obsolete outlet. To prevent electric shock do not use this polarized plug with an

extension cord, receptacle or other outlet unless the blades can be fully inserted without blade exposure. If you

need an extension, use a polarized cord.

5 Power Sources -- This video product should be operated only from the type of power source indicated on the

marking label. If you are not sure of the type of power supply to your home, consult your video dealer or local

power company. For video products intended to operate from battery power, or other sources, refer to the

operating instructions.

6 Overloading -- Do not overload wall outlets and extension cords as this can result in a risk of fire or electric

shock. Overloaded AC outlets and extension cords are dangerous, and so are frayed power cords, damaged or

cracked wire insulation and broken plugs. They may result in a shock or fire hazard. Periodically examine the cord

and have it replaced by your service technician if appearance indicates damage or deteriorated insulation.

7 Power-Cord Protection -- Power-supply cords should be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the appliance.

8 Ventilation -- Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the

video product and to protect it from overheating. These openings must not be blocked or covered. The openings

should never be blocked by placing the video product on a bed, sofa, rug or other similar surface. This video

product should never be placed near or over a radiator or heat register. This video product should not be placed

in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the video product

manufacturer's instructions have been followed.

9 Attachments -- Do not use attachments unless recommended by the video product manufacturer as they may

cause hazards.

Caution: Maintain electrical safety. Powerline operated equipment or accessories connected to this unit

should bear the UL listing mark or CSA certification mark on the accessory itself and should not have been

modified so as to defeat the safety features. This will help avoid any potential hazard from electric shock or

fire. If in doubt, contact qualified service personnel.

10 Water and Moisture -- Do not use this video product near water - for example, near a bath tub, wash bowl,

kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

11 Accessories -- Do not place this video product on an unstable card, stand, tripod, bracket, or table. The

video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only

IMPORTANT SAFEGUARDS - 6 -

with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any

mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory

recommended by the manufacturer.

11A An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven

surfaces may cause the appliance and cart combination to overturn.

12 Outdoor Antenna Grounding -- If an outside antenna or cable system is connected to the video product, be

sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-

up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with

respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding

electrodes, and requirements for the grounding electrode. See example below:

EXAMPLE OF ANTENNA GROUNDING

13 Power Lines -- An outside antenna system should not be located in the vicinity of overhead power lines or

other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an

outside antenna system, extreme care should be taken to keep from touching or approaching such power lines or

circuits as contact with them might be fatal. Installing an outdoor antenna can be hazardous and should be left to

a professional antenna installer.

USE

14 Cleaning -- Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or

aerosol cleaners. Use a damp cloth for cleaning.

15 Object and Liquid Entry -- Never push objects of any kind into this video product through openings as they

may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill

liquid of any kind on the video product.

16 Lightning -- For added protection for this video product during a lightning storm, or when it its left unattended

and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable-system.

This will prevent damage to the video product due to lightning and power-line surges.

SERVICE

17 Servicing -- Do not attempt to service this video product yourself as opening or removing covers may expose

you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18 Conditions Requiring Service -- Unplug this video product from the wall outlet and refer servicing to

qualified service personnel under the following conditions.

a. When the power-supply cord or plug is damaged

b. If liquid has been spilled, or objects have fallen into the video product.

c. If the video product has been exposed to rain or water.

d. If the video product does not operate normally by following the operating instructions. Adjust only those controls

that are covered by the operating instructions. Improper adjustment of other controls may result in damage and

will often require extensive work by a qualified technician to restore the video product to its normal operation.

IMPORTANT SAFETY INSTRUCTIONS FOR AC ADAPTER/CHARGER - 7 -

e. If the video product has been dropped or the cabinet has been damaged.

f. When the video product exhibits a distinct change in performance - this indicates a need for service.

19 Replacement Parts -- When replacement parts are required, have the service technician verify that the

replacements he uses have the same safety characteristics as the original parts. Use of replacements specified

by the video product manufacturer can prevent fire, electric shock or other hazards.

20 Safety Check -- Upon completion of any service or repairs to this video product, ask the service technician to

perform safety checks recommended by the manufacturer to determine that the video product is in safe operating

condition.

21 Heat -- The product should be situated away from heat sources such as radiators, heat registers, stoves, or

other products (including amplifiers) that produce heat.

IMPORTANT SAFETY INSTRUCTIONS FOR AC ADAPTER/CHARGER

1. Save these Instructions -- This page contains important safety and operating instructions for AC

Adapter/Charger Model VM-AC 85A.

2. Before using AC Adapter/Charger, read all instructions and cautionary markings on (1) AC Adapter/Charger,

(2) battery and (3) product using battery.

3. Also read all instructions on pages 4 and 5.

4. Caution -- To reduce risk of injury, charge only rechargeable battery, VM-BP82G, VM-BP82 or VM-BP84.

Other types of batteries may burst causing personal injury and damage.

5. Do not expose charger to rain or snow.

6. Use of an attachment nor recommended or sold by the battery charger manufacturer may result in a risk of fire,

electric shock, or injury to persons.

7. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting charger.

8. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or

stress.

9. Do not operate charger with damaged cord or plug - replace them immediately.

10. An extension cord should not be used unless absolutely necessary.

Use of improper extension cord could result in a risk of fire and electric shock. If extension cord must be used,

make sure:

A. The pins on plug of extension cord are the same number, size, and shape as those of plug on charger.

B. That extension cord is properly wired and in good electrical condition; and

C. That wire size should be met below:

Minimum

AWG size Length of extension cord (feet)

18 Equal to or less than 100

16 Equal to or less than 150

11. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take

it to a qualified serviceman.

12. Do not disassemble charger: take it to a qualified serviceman when service or repair is required. Incorrect

reassembly may result in a risk of electric shock or fire.

13. To reduce risk of electric shock, unplug charger from outlet before attempting any maintenance or cleaning.

Read This First

To guide you, we've included:

• A "Before You Begin" section containing important cautions for your family's safety as well as instruction for

getting your video camcorder ready for use. Please read and understand this section thoroughly before moving

on.

• A "Getting Started" section to familiarize yourself with the controls and prepare you for recording.

• A "Basic Techniques" section to allow you to use your video camcorder quickly and confidently before advancing

to the more sophisticated features of the Hitachi VM-E625LA.

• "Advanced Techniques" to help you with some of the exciting, sophisticated features of the Hitachi VM-E625LA.

We hope you will take the time to learn about these functions since they have been designed for you. You can

use the video camcorder without reading this section.

• A "General Maintenance" section to help keep your purchase in good repair.

We want this manual to be as helpful as possible, so it includes two easy ways to find the information you need:

Before You Begin - 8 -

• A quick index for the information you use most often (this page).

• A detailed table of contents directing you to specific information quickly (page 10).

Get to know your video camcorder by using this manual, and get to know Hitachi. We appreciate your business.

Quick Index

Charging the Battery.....12

Making a Basic Recording.....27

PlayBack.....27

Using Power Zoom.....35

Using Digital Zoom.....35

Using the Wireless Remote Control.....42

Dubbing from camcorder to VCR.....45

Before You Begin

Any problems that occur as a result of any of the following conditions will not be covered by our warranty.

 Be careful that no water, dust or sand enters the camcorder and all accessories.

 When you shoot at a scene which contains an extremely bright object such as the sun or a light source, a bright

vertical bar may appear in the picture.

Your camcorder is functioning properly, but the solid-state pickup device (C.C.D) usually causes this as an

inherent characteristic. Try to avoid shooting an excessive bright object directly.

 Be sure not to leave the camcorder in a place where the temperature exceeds 140°F (60°C), or the pickup

device may be damaged.

Dangerous includes:

• Inside a car with the windows closed and in direct sunshine.

• Near heating appliances.

 Do not leave the viewfinder lens facing sunlight for a prolonged period, or the phosphorescent surface of the

cathode ray tube or the liquid crystal display (LCD) panel may be damaged.

Features

• Easy to use

• 3-inch color liquid display (LCD) monitor

• 24x zoom ratio

• Instant zoom

• Multi-function TV/Cam remote control

• Electronic image stabilization (EIS)

• Recorded date search

• Automatic title recording

With this camcorder you can view the picture being recorded or the playback picture whether

on the LCD monitor or in the viewfinder. Opening or closing the LCD monitor switches the

picture to appear on the LCD monitor or in the viewfinder. The following text describes the

operation assuming that the viewfinder is used as a major monitor device.

Components and Accessories

Check that you have all the following components and accessories before preceding.

1. Audio/video cable

2. Battery pack

3. AC adapter/charger

4. Batteries for date/title and remote control

5. Shoulder strap

Before You Begin - 9 -

6. DC cord

7. Remote control

8. Lens cap string

Optional RF Adapter

If you wish to connect this camcorder to a television that does not have audio/video input jacks you will need to

use the optional RF adapter model VM-RF86A (R).

The RF adapter can be purchased by calling the telephone number below. For your convenience Visa, Master

Card, and American Express credit cards are accepted. The RF adapter can also be purchased by mail by

sending either money order or your credit card information to the following address:

HiTRON, Inc.

675, Old Peachtree RD.

Suwanee, GA 30174

Tel: 1-800-995-4500

For more information concerning the purchase of camcorder accessories, please see the optional accessory

listing on page 65.

Attaching the Shoulder Strap

Thread the ends of the provided shoulder strap through the slots at the back of the camcorder and thread through

the shoulder straps' buckles.

Note: Make sure that the straps are securely fastened before using the shoulder strap to carry the camcorder.

Lens Cap

Getting Started - 10 -

Using the lens cap string:

Pass the string through the lens cap and grip belt and attach it as shown in the figure.

Removing the lens cap

Always attach the lens cap to protect the lens when carrying or storing the camcorder. During shooting attach the

lens cap as shown in the figure to prevent it from being lost.

Getting Started

This section guides you through the initial preparation of the camcorder. None of these processes are complex.

Set aside some time, relax, and familiarize yourself with this quality instrument.

Enjoy getting to know all about your Hitachi 8mm camcorder. The more comfortable and familiar you are with the

machine and its features, the more you can make it do for you. Let's get started!

It is crucial that you read and understand all the safety instructions before you begin. If you haven't read the safety

instructions yet, please take the time to do so now.

Charging the Battery

The first step is to set the battery to charge. It takes approximately 1 1/4 hours (VM-BP84), enough time to

familiarize yourself with some of the basic features of the camcorder. Once fully charged the battery will give an

operating time of approximately 40 minutes, but this is reduced to a half to one-third depending on how often you

use zoom and start/stop functions.

Charge the battery at a temperature range of 50°F(10°C) - 86°F(30°C) to prevent damage to the battery.

1. Plug the AC adapter/charger power cord into an AC outlet. Make sure that the wide blade fits into the wide slot.

If it doesn't fit try reversing it. If you still cannot make fit the blades fully into the outlet either contact an electrician

to replace your obsolete outlet, or use a polarized cord or outlet accessory.

2. To insert the battery into the charger align the reference arrow on the battery with the reference arrow on the

AC adapter/charger. Push the battery till it is flush with the AC adapter/charger sliding it in the direction of the

arrow as shown in the figure.

3. The CHARGE light remains on while the battery charges, turning off when charging completes.

Note: Remove the DC cord from the AC adapter/charger before attempting to charge the battery. The

CHARGE light flashes if the DC cord remains connected while you attempt to charge the battery.

Note: Do not operate the battery at temperature below 14°F (-10°C) or above 95°F (35°C). At extremely low

Getting Started - 11 -

temperatures operation time decreases, while at high temperature the battery may be damaged.

After charging set the mark switch to red so that you may quickly identify whether the battery is

charged or uncharged.

Note: The marker switch does not guarantee the batteries charge status.

Additional Information

To use a battery in optimum condition:

• Use the battery until the low charge light (

) flashes. Using a battery for a short time and then recharging it

may shorten the operation time.

• It is recommended to refresh a battery before recharging it when it has not been used for long time; otherwise its

operation time becomes short. Press the refresh button.

After refreshing is complete, the REFRESH light turns off and the CHARGE light turns on and charging begins

automatically.

Refreshing a fully charged battery takes approximately 5 hours (VM-BP84), adding considerable time to battery

charging.

With repeated normal charging and use the battery will gradually lose operating time. When operation time

becomes too short to be useful, replace the battery.

If the POWER light begins to flash during charging, remove the battery and then reattach it to the AC

charger/adapter. If the POWER light continues to flash after several attempts to attach it, the battery is unable to

take a charge and must be replaced.

Do not attach a hot battery to the AC adapter/charger. Allow it to cool. Attaching a hot battery to the AC

adapter/charger causes the POWER light to flash.

THERE ARE NO USER-SERVICEABLE PARTS INSIDE THE BATTERY OR AC ADAPTER/CHARGER.

THROWING THE BATTERY INTO FIRE OR EXPOSING IT TO EXCESSIVE HEAT (ABOVE 149°F [65°C]) MAY

CAUSE INJURY.

SHORTING THE BATTERY'S TERMINAL INCREASES RISK OF FIRE OR ELECTRICAL SHOCK.

ATTENTION:

The product that you have purchased contains a rechargeable battery. The battery is

recyclable. At the end of its useful life, under various state and local laws, it may be

illegal to dispose of this battery into the municipal waste stream. Check with your local

solid waste officials for details in your area for recycling options or proper disposal.

Getting Started - 12 -

Adjusting the Electronic Viewfinder

The electronic viewfinder adjusts simply by pivoting it to a position where it is comfortable and easy to see

through. Place the viewfinder back in its original position before storing the camcorder in its case or carrying the

camera recorder around to avoid damaging the viewfinder or camcorder.

Eyepiece Adjustment

To use the electronic viewfinder, turn this control for your optimum focus adjustment.

Adjustment the Hand Strap

Adjust the hand strap to best fit your hand. After adjustment, hook the hand strap's pad securely.

Getting Started - 13 -

Loading Batteries

Install the batteries to prevent misplacing them.

Clock Battery

1. Pull out the battery holder.

2. Insert the battery with the "+" terminal facing up.

3. Fully insert the battery holder into the camcorder.

Remote Control Battery

1. Push the tab to the right of the remote control and hold it, then remove the battery holder.

2. Press the PLAY button and hold it for about two seconds.

3. Insert the battery with the "+" terminal facing up as shown in the figure.

4. Replace the battery holder with battery in the remote control making sure that it is fully inserted.

WARNING: KEEP THE BATTERIES AWAY FROM CHILDREN AND PETS.

IF SWALLOWED CONSULT A PHYSICIAN IMMEDIATELY FOR EMERGENCY TREATMENT.

Note: Replace the batteries with 3V micro lithium cells such as Maxell CR2025 or its equivalent.

Note: Dispose of battery safely in accordance with local laws. Do not dispose of in fire.

Note: Do not short circuit the batteries.

Note: Do not take apart the batteries.

Note: Do not hold the batteries with the metallic tweezers.

Note: Do not re-charge the batteries.

Getting Started - 14 -

Note: Keep the batteries in a dark, cool, dry place.

Camcorder Batteries Using Battery Pack

Before you install the battery for the first time it must be fully charged. Refer to "Charging the Battery" on page 12

for details.

1. Lift the OPEN lever and pull it up. The power supply attachment cover will open.

2. With the battery compartment facing you, align arrow on the battery with the arrow on the camcorder.

3. Once the arrows are aligned, push down on the battery.

4. While pushing down the battery, slide it to the right until it "clicks" into place.

5. After installing the battery, close the cover. Hold the OPEN lever and align the tabs on both sides of the cover

with the end of the attachment section.

Getting Started - 15 -

Note: If the OPEN lever is flat, the cover will not close.

Note: Always remove the battery from the camcorder after use.

Note: We cannot guarantee against malfunctions of the camcorder which occur when you use battery packs

other than those specified.

Note: Always attach a battery by the procedure described here. Attaching a battery forcibly could damage it.

Removing the Battery Pack

1. Lift the OPEN lever and pull it up. The power supply attachment cover will open.

2. Push the side of the battery in the direction of the arrow. A click will be heard and the battery is released.

3. Remove the battery and close the cover.

Checking the Battery's Charge

A battery charge indicator is located on the upper right corner of the viewfinder. One of three symbols displays

when the battery is used.

This symbol indicates a fully charged battery.

This symbol indicates a partially charged battery.

This flashing symbol indicates a battery nearly out of power. Use an alternate power source or

charge the battery before continuing to use the camcorder.

Using Alkaline Dry-Cell Batteries

The camcorder can be powered by six alkaline dry-cell batteries inserted into the power supply attachment holder.

The continuous operation time of the camcorder depends on the type of alkaline batteries used. Please ensure

that CAM/OFF/VIDEO switch is in the OFF position whenever attaching or detaching any power supply (i.e.

Battery, AC adapter/charger, etc.)

Note: When alkaline batteries are used to power the camcorder, power is not supplied to the LCD monitor, so

Getting Started - 16 -

you cannot view a picture on the LCD screen.

1. Lift the OPEN lever and pull it up. The power supply attachment cover will open.

2. Lift the battery holder plates at the center of the attachment holder.

3. Insert six alkaline batteries with the correct polarities.

4. After installing the batteries, close the cover. Hold the OPEN lever and align the tabs on both sides of the cover

with the end of the attachment section.

Note: Use only "AA" alkaline batteries marked "LR6". (Manganese batteries cannot be used to power the

camcorder.)

Note: It is recommended that you use alkaline batteries within the recommended period of use or within two

years of the date of manufacture.

Note: Be careful of the following to prevent the leakage of liquid or an explosion.

• Check that the orientation (polarity) of the batteries is correct.

• Remove the batteries when not using the camcorder.

• Remove the used batteries from the camcorder.

• Do not use batteries made by different manufacturers at the same time.

Getting Started - 17 -

• Do not use old and new batteries at the same time.

Note: If the liquid leaks, remove the batteries immediately and ask your nearest dealer to inspect the

camcorder (this will be at your own expense).

Note: Do not let the batteries or the terminals of the camcorder get dirty. If they are dirty, use a dry cloth to

wipe off the dirt completely.

Note: It is recommended that you use a battery pack to power the camcorder when using a DC camera light.

If a camera light is used when the camcorder is powered by batteries, the required supply voltage will be very

short and the camcorder will turn off soon.

Note: When the batteries are used to power the camcorder in a cold place, it may not operate normally; the

operation time may become extremely short or the camcorder may not be turned on. It is recommended that

you use a battery pack to power the camcorder in a cold place. (At 50°F (10°C), the chemical reaction

decreases the capacity of battery to one-tenth when compared to that at normal temperature 68°F (20°C).)

Note: Noise may appear momentarily in the viewfinder when recording is started or stopped.

Note: Be careful when touching the batteries with your bare hand to remove them as they are warm during

and just use.

Note: Since the supply voltage from batteries decreases more abruptly when compared to that from a battery

pack, the battery remaining level indicator ( ) may not flash in the viewfinder, noise may occur, the picture

and sound may not be recorded normally and/or the power may be turned off soon. These phenomena occur

because the capacity of batteries becomes low. So turn the power switch off and replace the batteries. If the

power switch is left turned on in this state, the power may turn on temporarily and turn off again repeatedly.

Note: Be sure not to short, disassemble, heat or throw batteries into fire. This is very dangerous.

Using Alternative Power Sources

Using the AC Adapter/Charger

Please ensure that the CAM/OFF/VIDEO switch is in the OFF position whenever attaching or detaching any

power supply (ie. battery, AC adapter/charger, etc.)

1. Plug the AC adapter/charger power cord into an AC outlet. Make sure that the wide blade fits into the wide slot.

If it doesn't fit try reversing it. If you still cannot make fit the blades fully into the outlet either contact an electrician

to replace your obsolete outlet, or use a polarized cord or outlet accessory.

2. Connect one end of the DC cord (provided) to the DC IN jack of the camcorder. Connect the other end of the

DC cord to the DC OUTPUT of the AC adapter/charger.

Note: The AC adapter/charger can be used around the world. An AC plug adapter is required in some foreign

countries. If you need one purchase it at your Hitachi distributor.

Note: The battery level indicator sometimes displays the partial charge symbol when using the AC

adaptor/charger. Ignore this indicator when using the AC adaptor/charger.

Using a Car Battery

The camcorder can be powered with a car battery by using an optional car battery cord (Hitachi VM-CC80A) to

plug the camcorder into the car's cigarette lighter socket. Please ensure that the CAM/OFF/VIDEO switch is in the

OFF position whenever attaching or detaching any power supply (ie. battery, AC adapter/charger, etc).

Getting Started - 18 -

1. Plug the car battery cord into the car's cigarette lighter socket.

2. Connect one end of the DC cord (provided) to the DC IN jack of the camcorder. Connect to other end of the DC

cord to the DC OUTPUT of the car battery cord.

Note: Only use the car battery cord with cars having 12/24 volt negative ground system.

Inserting and Removing Cassettes

A power source must be connected before inserting or removing cassettes. Once connected cassettes can be

inserted or removed whether the CAM/OFF/VIDEO switch is on or off.

Inserting a Cassette

1. Press the PUSH OPEN button to open the LCD monitor ("Opening the LCD Monitor", p25).

2. Press the EJECT button. The cassette door opens automatically.

Caution: Be careful not to catch your fingers between the cassette door and the camcorder as it could cut

you.

3. Place the cassette in the cassette holder so that the transparent window faces away from the body of the

camcorder and the sprockets toward the body of the camcorder.

4. Push the cassette holder, which is embossed PUSH LOCK on the left hand side, until it "clicks" into place. The

camcorder automatically closes.

Caution: Be sure that you push the cassette holder embossed PUSH LOCK to close the holder. Otherwise,

the holder will not click into place and the tape may be slack which could lead to damage.

Getting Started - 19 -

Note: If TAPE flashes in the viewfinder, remove the cassette and check that the tape is not damaged, is not

slack or no dust adheres to it, etc. After making sure that there is no abnormality, reinsert the cassette. If

TAPE reappears, see "Troubleshooting" on page 59.

Removing a Cassette

Slide the EJECT switch in the direction of the arrow. The cassette door opens automatically. Remove the

cassette.

Protecting Recorded Material

Protect 8mm cassettes from accidental erasure by sliding the tab on the side of the cassette towards the opposite

side until the tab is completely visible. Slide the tab in the opposite direction, until the tab disappears, to record on

the cassette again.

Using the Linear Time Counter

The linear time counter displays the tape run in hours, minutes, and seconds, helping you to keep track of how

long you've been filming or time you have left to film before running out of tape.

Turn the camcorder on to display the linear time counter. The linear time counter keeps track from when you load

a cassette into the camcorder and clears to 0:00:00 when the cassette is ejected.

Remaining Tape

The tape remaining display shows the remaining tape that can be used for recording and playback, using seven

dashes. This feature is handy when recording since it lets you know how long you can record on the loaded tape.

Insert a cassette into the camcorder and start recording or playback; 10 seconds later, the remaining tape will be

displayed. When the cassette is ejected, the display will disappear. "

" is displayed for 10 seconds

after the tape starts to run.

Getting Started - 20 -

Note: The tape remaining display appears 10 seconds after the tape starts to run.

Note: When the remaining tape time becomes less than about three minutes, TAPE END flashes in the

viewfinder or LCD monitor.

Setting the Date and Time

Take the time to set the date and time now. The date and time can be recorded on your tapes to act as a handy

reference when viewing them later. Use the following procedure to set up the display for the current date and

time.

Note: Be sure to insert the clock battery before setting the date and time. Although the date and time can be

set without the clock battery inserted, they will disappear when the battery providing power to the camcorder

is removed.

Make sure that the current time is displayed correctly before you start filming.

1. Load the battery ("Loading the Batteries: Camcorder batteries" p15). Press the red button on the

CAM/OFF/VIDEO switch as you slide it to CAM.

2. Press the DATE/TITLE button and look into the viewfinder. The date and time should appear in the lower right

with the "1" flashing.

3. Pressing the F.F button gives you higher numbers while the REW button gives you lower numbers. Select the

right month and press STOP button. Use the F.F, REW and STOP buttons to select the proper day, year, hour,

minute, and AM or PM.

4. After setting the AM/PM, press the DATE/TITLE button. The display changes and the internal clock starts.

Note: After the date and time are set, " AUTO" appears and the camcorder enters the automatic date

recording mode. See "Date Recording" on page 34.

Page is loading ...

Hitachi VM-E625LA User manual

Brand: Hitachi

Model: VM-E625LA

Category: Camcorders

Type: User manual

This manual is also suitable for

VME-625LA - Camcorder

Download PDF

report

Hitachi VM-E625LA User manual

This manual is also suitable for

Hitachi VM-E625LA User manual

Related papers

Other documents