Josef Kihlberg a.560B22CL User manual

Brand: Josef Kihlberg

Model: a.560B22CL

Category: Power tools

Type: User manual

BATTERY-POWERED

TOP STAPLER

BATTERI-DRIVEN

LOCKHÄFTARE

c.561B a.560B

c.561B22 a.560B22

Patent pending

Patentsökt

V 05.19

EN PAGE 2 OPERATING MANUAL

SE SIDA 25 ANVÄNDARHANDBOK

EN 2

Original operating manual according to “Machine Directive” 2006/42/EEC.

Read this manual carefully.

This manual is part of the product and therefore should be kept for later use or a future owner.

Validity

c.561B from Series no 1904xxx

c.561B22 from Series no 1904xxx

a.560B from Series no 1904xxx

a.560B22 from Series no 1904xxx

Manufacturer / Customer service

Josef Kihlberg AB

Industrigatan 37B

544 50 Hjo, SWEDEN

www.kihlberg.com

(or local sevice center)

(for stapling tools with LED indicators only)

TABLE OF CONTENTS

Table of contents

1 General information ................................................................................. 4

1.1 Conventions and symbols used within this manual ...................................... 4

1.2 Disposal and environmental protection ........................................................4

2 Safety ........................................................................................................ 5

2.1 Intended Use ................................................................................................5

2.2 Forseeable misuse .......................................................................................5

2.3 Working safely ..............................................................................................5

2.4 General safety warnings for power tools ......................................................6

2.5 Safety instructions for stapling tools .............................................................8

3 Getting to know your stapler ................................................................ 10

3.1 Overview ....................................................................................................10

3.2 User Interface .............................................................................................11

3.3 Tool status indicator ...................................................................................11

3.4 Battery and charger ....................................................................................11

3.5 Function .....................................................................................................12

3.6 Transporting the stapler .............................................................................13

3.7 Scope of delivery ........................................................................................13

3.8 Optional features ........................................................................................13

4 Preparing for operation ......................................................................... 14

4.1 Charging the battery ...................................................................................14

4.2 Inserting/removing battery from tool ...........................................................14

4.3 Checking charge status ..............................................................................14

4.4 Setting/description of operating modes ......................................................15

4.5 Loading the stapler .....................................................................................15

5 Operation ................................................................................................ 16

5.1 Activating the stapler from sleep mode ......................................................16

5.2 Operating the stapler ..................................................................................16

5.3 Checking staple clinch ...............................................................................17

5.4 Adjusting staple leg length .........................................................................17

5.5 Adjusting penetration depth .......................................................................18

5.6 Adjusting staple clinch ................................................................................18

6 Preventive and corrective maintenance .............................................. 19

6.1 Preventive maintenance schedule .............................................................19

6.2 Cleaning the stapler ...................................................................................19

6.3 Removing jammed staples .........................................................................19

6.4 Removing/installing the magazine .............................................................20

6.5 Cleaning/replacing the driver blade (pos. 3) ..............................................20

6.6 Cleaning/replacing the clinchers (pos. 4) ...................................................21

7 Troubleshooting .....................................................................................22

8 Technical data ........................................................................................ 23

EC Declaration of Conformity (copy) ............................................................. 24

EN 4

GENERAL INFORMATION

1 General information

1.1 Conventions and symbols used within this manual

DANGER

Indicates a hazard with a high level of risk, which, if not avoided, will result in death or serious

injury.

WARNING

Indicates a hazard with a moderate level of risk, which, if not avoided, may result in death or

serious injury.

CAUTION

Indicates a hazard with a minor level of risk, which, if not avoided, may result in minor or moder-

ate injury.

ATTENTION

Indicates a situation that can lead to material or environmental damage or poor operating

results.

INFO

Indicates hints and recommendations.

►This symbol identies action steps.

→This symbol indicates results from action steps.

●This symbol identies list items.

1.2 Disposal and environmental protection

These tools are manufactured without any chemical substances which

could be dangerous to health. Nevertheless, potential health damage

may occur from battery liquid if batteries are treated or disposed of

inadequately. Therefore, it is important to protect health and also

promote the reuse and environmentally-appropriate recycling of waste.

Chargers and batteries should be sorted for environmentally-friendly

recycling and disposed of separately.

The legal prescriptions for disposal of all parts must be observed.

►Chargers and batteries should be sorted for environmentally-friendly recycling.

►Observe warnings and instructions of the battery manufacturer stated in the operating instruc-

tions of the battery.

The following harmonised standards have also been taken into consideration:

●Directive 2011/65/EU of 8 June 2011 on the restriction of the use of certain hazardous substan-

ces in electrical and electronic equipment (RoHS II).

●Directive 2012/19/EU of 4 July 2012 on waste electrical and electronic equipment (WEEE II).

SAFETY

2 Safety

2.1 Intended Use

These tools are intended for closing boxes made from cardboard. These tools are intended

for stapling with staples as specied in Section “8”. Only use these tools as described in this

manual.

2.2 Forseeable misuse

●Do not use staples which are not listed in Section “8”.

●Do not place any staples into unsuitable material.

●Never use these tools to attach electrical cables.

●Do not modify tools without prior authorisation.

●If your stapler is equipped with a position guidance laser (option) never direct laser at persons.

Do not look directly into the laser.

2.3 Working safely

This manual must always be available at the place of operation of the

stapling tool. It must be read and observed by all persons working with

or in the vicinity of the stapling tool.

Preventive and corrective maintenance on the tool may only be carried

out by trained personnel. In addition to this manual, the applicable local

rules for accident prevention and safe and professional operation must

be observed.

The operator or his supervisor is responsible for safe stapling and the selection of the correct

staples (as specied in Section “8”) for the package, depending on its dimensions, weight, stabil-

ity and the way it will be transported and stored.

Only staples specied for the tool type (Section “8”) must be used. The tools should be adjusted

appropriately for the staples and the package used. The operator is responsible for the correct

tool settings and adjustments.

Wear protective equipment

When operating the tool, wear hand protection (cut-proof gloves) and

safety shoes.

Safety goggles should always be worn by the operator and others in

the work area when loading, operating or servicing these tools.

EN 6

SAFETY

2.4 General safety warnings for power tools

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, re and/or serious

injury. Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

2.4.1 Work area safety

a) Keep the work area clean and well lit. Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of ammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a power tool. Distractions can cause you to

lose control.

2.4.2 Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will

reduce the risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords

increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of electric shock.

2.4.3 Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do

not use a power tool while you are tired or under the inuence of drugs, alcohol or medication.

A moment of inattention while operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protective equipment such as

dust masks, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will

reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to the

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

nger on the switch or energising power tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

SAFETY

g) If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

2.4.4 Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application. The correct power

tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the power tool before

making any adjustments, changing accessories, or storing power tools. Such preventive safety

measures reduce the risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the

power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and

any other condition that may affect the power tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking

into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

2.4.5 Battery tool use and care

a) Recharge only with the charger specied by the manufacturer. A charger that is suitable for one

type of battery pack may create a risk of re when used with another battery pack.

b) Use power tools only with specically designated battery packs. Use of any other battery packs

may create a risk of injury and re.

c) When the battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection from one

terminal to another. Shorting the battery terminals together may cause burns or a re.

d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, ush with water. If liquid contacts eyes, additionally seek medical help. Liquid

ejected from the battery may cause irritation or burns.

2.4.6 Service

a) Have your power tool serviced by a qualied repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

EN 8

SAFETY

2.5 Safety instructions for stapling tools

WARNING

Read all safety warnings and all instructions in this manual and in the battery charger

operating instructions.

Failure to follow the warnings and instructions may result in electric shock, re and/or serious

injury. The following hazards can result in serious injuries.

Stapling tool safety warnings:

Always assume that the tool contains staples. Careless handling of the stapling tool can

result in unexpected ring of staples and personal injury.

Do not point the tool towards yourself or anyone nearby. Unexpected triggering will dis-

charge the staple causing an injury.

Do not actuate the tool unless the tool is placed rmly against the workpiece. If the tool is

not in contact with the workpiece, the staple may be deected away from your target.

Disconnect the tool from the power source when the staple jams in the tool. While remov-

ing a jammed staple, the stapling tool may be accidentally activated if it is plugged in.

Use caution while removing a jammed staple. The mechanism may be under

compression and the staple may be forcefully discharged while attempting to free a jammed

condition.

Do not use this tool for fastening electrical cables. It is not designed for electric cable

installation and may damage the insulation of electric cables thereby causing electric shock or

re hazards.

Danger of jamming and crushing. Do not place hands or other body parts between or under

the tool and the packaged goods during the stapling process.

Loose and falling packaged goods in the case of faulty stapling.

Check the staple seal. Never transport packaged goods if loads look unbalanced or incorrect.

Risk of explosion in EX (Explosive) zones. The tool must not be used in areas where explo-

sions can occur as a result of the environment or products being used.

Damage due to humidity. Do not clean the tool with water or steam. When using the tool

outdoors, protect it from rain. If the tool or the battery has water damage, it can cause re or

explosion.

Compressed air for cleaning work, risk of injury. When cleaning with compressed air, no air

must penetrate the body via skin lesions. Use only clean and dry compressed air. Use a blow

gun with a multi-hole nozzle. Wear eye protection.

SAFETY

CAUTION

The following dangers can result in minor or moderate injury:

Noise exposure

Wearing hearing protection is recommended.

Vibration exposure

The vibration level of these tools is lower than the permissible exposure limit.

The vibration level specied in this manual has been measured according to a measurement

method standardised in EN 60745 and can be used for the comparison of power tools with each

other. It is also suitable for a preliminary estimation of the vibration load.

The vibration emission value measured may, however, deviate from the specied value depend-

ing on the actual application and the manner of operation. Under certain circumstances, the

vibration load may be increased temporarily or may be signicantly smaller over the entire work

period. For a more accurate assessment of the actual vibration load, the times should also be

considered when the device is switched off, or is running but not actually being used. This could

reduce the vibration load signicantly over the entire work period.

Therefore, dene additional safety measures against the effect of vibrations for the protection of

the operator, such as, for example: maintenance of the tool and organisation of work processes.

Warning sign on protection plate at the bottom of the stapler and on rear

housing.

Since the box detection sensors do not distinguish between cardboard and e.g. by the ngers

of the operator, there is a risk that the operator may be injured when operating the trigger by

driving staples (extending driver blade and clinchers).

ATTENTION

Avoid damage to the tool:

Use only original JOSEF KIHLBERG staples.

Using non-original staples may impair operational safety and will void the warranty and any

liability.

Use only original JOSEF KIHLBERG spare parts.

Using non-original spare parts may impair operational safety will void the warranty and any

liability.

Use only Bosch batteries and chargers.

Batteries and chargers are described in Section “3.7”.

EN 10

GETTING TO KNOW YOUR STAPLER

3 Getting to know your stapler

3.1 Overview

1 Battery

2 Battery release

3 Magazine pusher

4 Magazine with staple type

indication

5 Staples

6 Safety latch

7 Trigger

8 Magazine quick snap system

9 Tool status indicator

10 Screw for staple length

adjustment

11 Penetration depth setting knob

12 Staple clinch adjusting nut

13 Mode button

14 Suspension hanging port

(for stationary workplaces)

15 Battery charge status indicator

16 Clinchers

17 Box detection

18 Locking screw

(for staple length adjustment)

19 Company label (sticker)

Serial number syntax is as follows (JJMMYYYY)

JJ → Year; MM → Month; YYYY → consecutive number

13 3

16 16

GETTING TO KNOW YOUR STAPLER

3.2 User Interface

1 Display “Battery charge status” (see also Section “4.3”)

2 Mode indicators: MAN, SEMI, AUTO (see also Section “4.4”)

3 Button “Mode”

→One click: select mode of operation

→Hold button (approx. one second): activate or deactivate

optional laser

3.3 Tool status indicator

3.4 Battery and charger

1 Battery

2 Charger

3 Battery release

4 LED indicator

For detailed information, refer to the operating instructions

of battery and charger.

Whilst getting started:

blue LED pulsating twice:

indicates that battery has been inserted and trigger has

been actuated once → tool turns on

During operation:

blue LED slowly pulsating “ready for operation”

green LED permanently on “tool in stapling position”:

indicates activated box detection and nger on trigger

(trigger sensor)

red LED slowly pulsating / permanently on “tool error”:

(see also Section “7”)

EN 12

GETTING TO KNOW YOUR STAPLER

3.5 Function

The stapling tool is positioned on the package to be closed (box detection sensors activated).

By actuating the trigger the stapling process is started:

→During the downward movement of the driver blade (1), a staple (2) is sheared off the staple

strip.

→The staple is pushed into the package by the driver blade and bent (4) using the clinchers

(3).

→The clincher and driver blade are released from the packaged goods in an upward move-

ment and brought into the initial position.

You can choose between three operating modes: (see also Section “4.4”)

→Manual

→Semi-automatic

→Automatic

You can also choose between different staple types:

→c.561B: Width 32 mm (11/4″) / Length 15–18 mm (5/8–3/4″)

→c.561B22: Width 32 mm (11/4″) / Length 22 mm (7/8″)

→a.560B: Width 35 mm (13/8″) / Length 15–18 mm (5/8–3/4″)

→a.560B22: Width 35 mm (13/8″) / Length 22 mm (7/8″)

→Staple length 15 mm (5/8″) for total cardboard thickness 5–9 mm (0.20–0.35″)

→Staple length 18 mm (3/4″) for total cardboard thickness 7–12 mm (0.28–0.47″)

→Staple length 22 mm (7/8″) for total cardboard thickness 11–16 mm (0.43–0.63″)

●The staple leg length can be set (see Section “5.4”).

●The staple penetration depth can be set (see Section “5.5”).

●The staple clinch can be set (see Section “5.6”).

GETTING TO KNOW YOUR STAPLER

3.6 Transporting the stapler

To prevent accidental triggering while carrying the tool, make sure that the handle is gripped by

hand and the index nger is behind the shoulder (1).

3.7 Scope of delivery

For stapling tools

c.561B / a.560B: ●Battery BOSCH Li-Ion 12 V/4.0 Ah (EU) part no 137035

●Battery charger BOSCH GAL 1230 CV (230 V) (EU) part no 137033

or for USA version: ●Battery BOSCH Li-Ion 12 V/4.0 Ah, BAT420 part no 137034

●Battery charger BOSCH BC330 (115 V) part no 137032

Tool kit consisting of (including

in the scope of delivery) ●Allen key Torx T10, part no 942070

●Allen key Torx T20, part no 942071

3.8 Optional features

Position guidance laser system

Depending on which model you have chosen, your stapler may be

equipped with one of two position guidance laser systems:

●Line-Laser (front laser)

For positioning guidance with one front laser.

●Cross-Laser (three lasers)

For positioning guidance with one front and two side lasers.

If your stapler is equipped with this position guidance laser feature,

additional risks may be involved, if the laser is, for instance, directed at

persons:

The laser is only activated when the trigger is actuated.

A disruptive effect is possible with a laser device of class 1.

This means that persons in the immediate vicinity can feel disturbed or

distracted by the laser.

(Predictable misapplication: Laser is directed at persons. Look directly

into the laser)

LASER 1

EN 14

PREPARING FOR OPERATION

4 Preparing for operation

4.1 Charging the battery

For detailed information, see enclosed operating instructions of battery and charger.

WARNING

Only use Bosch batteries and chargers for your country as described in this manual (see

Section “3.7”). Use of other batteries/chargers can result in injury or re. To avoid the risk of

personal injury or re, read the battery charger operating instructions prior using the charger and

battery.

►Connect charger to mains.

→Green LED illuminates (charger ready for use).

►Insert battery in charger.

→Green LED ashes: Battery is being charged.

→Green LED illuminates continuously: Battery is fully charged.

→Red LED illuminates continuously: Battery temperature

outside charge-temperature range.

→Red LED ashes: see operating instructions for charger.

●Charging time: Charging of empty battery (80% / 100%):

approx. 60 / 80 min. (US: approx. 120 / 160 min.)

●Ideal battery temperature during charging process: 15–40 °C

(59–104 °F)

●Avoid battery temperatures below 0 °C (32 °F) and higher than

+45 °C (113 °F) during the charging process.

●Battery can be charged at any time, regardless of charge status.

4.2 Inserting/removing battery from tool

►Insert the charged battery into the tool. The unlock buttons must engage in the tool.

→The tool status indicator, indicates: Bright blue pulsating LED (2x).

→If the tool is not used for approx. two minutes the tool changes into sleep mode. Cancel

sleep mode by actuating trigger once.

→If the tool is not used for a long period (days) the battery must be removed from the tool.

►Press the unlock buttons and remove the battery at the same time.

4.3 Checking charge status

LED display "Battery charge status" on digital user interface with battery inserted:

1 maximum battery charge

2 high battery charge

3 good battery charge

4 empty battery (battery must be charged)

12 3 4

PREPARING FOR OPERATION

hold

4.4 Setting/description of operating modes

►Press the “MODE” button shortly.

→The mode changes to MAN, SEMI or AUTO.

MAN (Manual stapling)

Individual staples are inserted. A cycle is initiated after the tool is

placed on the package and the trigger is actuated manually.

Recommended for varying (soft, hard) packaged goods.

SEMI (Semi-automatic stapling)

Several staples can be inserted. Actuate trigger and hold it. As soon as the stapler is placed on a package,

a stapling cycle is activated via box detection. A new cycle is then started, if the stapler is lifted off and

placed back on the package (with the trigger held continuously). Recommended for large quantities of

identical packaged goods.

AUTO (Automatic stapling)

Several staples can be inserted over a predened interval. As soon as the stapler is placed on a package

and the trigger is being actuated and held in this mode, staples will be inserted over the predened period.

With every further actuation (and holding) of the trigger, this cycle starts anew. A maximum of 20 staples will

be inserted without lifting off. Recommended for large quantities of identical packaged goods or long

packages.

4.5 Loading the stapler

There is a reloading mark (arrow) (1) on both sides of the magazine. If

there are just a few staples left in the magazine, the staples should be

lled up. The correct type of staple is marked on the left side of the

magazine. Make sure to use the right length of staples for your

application.

WARNING

Unexpected startup during loading.

• Remove the battery!

►Pull the pusher (2) all the way out and x it in the rear position.

►Place staple strips (3) into magazine from the top.

CAUTION

Danger of crushing.

• Active feeding of the pusher until it reaches the staples.

►Lift the pusher to release it.

►Move the pusher forward carefully until it reaches the staples.

►Insert the battery into the tool.

►If necessary, adjust staple length (see Section “5.4”)

EN 16

OPERATION

5 Operation

5.1 Activating the stapler from sleep mode

To avoid unnecessary battery discharge, the tool switches to ener-

gy-saving mode (sleep mode) after a short time.

→The user interface goes dark (not illuminated).

→The tool status indicator is switched off.

►Release the safety latch and actuate the trigger once.

→The sleep mode is switched off again.

→The tool status indicator changes to blue and pulsates slowly.

→The user interface switches on.

5.2 Operating the stapler

Preconditions

a) The tool is adjusted to correct staple lengths and penetration depth (see Section “5.4”/“5.5”).

b) The charged battery is inserted (see Section “4.2”).

c) The desired operating mode is set (see Section “4.4”). In this description it is assumed that

the selected operating mode (default mode) is “MAN” (manual stapling).

WARNING

Danger of injury!

Always place yourself in a rmly balanced position when using or handling the tool.

►Place tool on package and hold the tool against package (box detection covered).

WARNING

Danger of injury!

Before stapling, ensure that your hand or any other part of your body is not underneath the tool

or in the package to be closed.

►Pull the safety latch (1).

►Actuate the trigger (2).

The position of the tool status indicator (3) on both

sides of the tool is equal to the stapling line (position).

►Move the tool and repeat until the stapling is nished.

►Carry out a visual inspection of the staple clinch (see Section

“5.3”).

OPERATION

5.3 Checking staple clinch

WARNING

Danger of injury!

Never transport or move packaged goods with improperly performed stapling.

Perform staple check after each stapling.

Performing a staple check by visual inspection

1 Good staple clinch

2 Poor staple clinch

→Leg length of staple too long or overbent

3 Poor staple clinch

→Leg length of staple too short or not bent enough

Always use JOSEF KIHLBERG original staples!

►If necessary adjust staple clinch (see Section “5.6”).

►If good stapling is not achieved, the tool must be checked by an authorized service center.

5.4 Adjusting staple leg length

The stapler can be adjusted to a 15 (5/8″) or 18 mm (3/4″) staple leg length.

►Remove battery from tool.

►Adjust penetration depth to deep (MAX) (see Section “5.5”).

►With a Torx T10 key, unscrew locking screw (1) below the tool by

two turns.

►With a screwdriver, adjust screw (2) to 15 (5/8″) or 18 mm (3/4″) leg

length.

►Retighten the locking screw (1).

For 22 mm (7/8″) staple leg length, use 18 mm (3/4″) setting

(c.561B22 and a.560B22 = 22 mm (7/8″).

15 mm18 mm

EN 18

OPERATION

5.5 Adjusting penetration depth

The depth of the stapling, i. e. the extent to which the driver plate penetrates the material, is

easy to adjust using the setting knob.

►Depress the setting knob and turn it to any of its ve positions.

→MIN = Lowest stapling penetration

(i. e. smallest resulting leg length)

→MAX = Deepest stapling penetration

(i. e. longest resulting leg length)

5.6 Adjusting staple clinch

It is recommended to adjust the staple clinch, i. e. how tightly the staples close.

►Remove battery from tool.

►Remove housing plug over slot.

►With a small screwdriver turn the adjusting nut behind the slot:

→Turn to the right to close the clinch (→).

→Turn to the left to open up the clinch (←).

PREVENTIVE AND CORRECTIVE MAINTENANCE

6 Preventive and corrective maintenance

WARNING

Unintended actuation of trigger and safety latch during maintenance work could lead to

injuries. Always remove battery before performing cleaning or preventive and corrective mainte-

nance work.

6.1 Preventive maintenance schedule

Task Interval (cycles)

Cleaning the stapler (see Section “6.2”) Weekly (for approx. 100-300 staplings/day)

Tool inspection (recommended) Every 2 years, service by specialist unit

(i. e. manufacturer or local dealer)

6.2 Cleaning the stapler

In the case of heavy dirt accumulation it is recommended that the tool be cleaned regularly

(daily). In particular, the driver blade, the box detection and the clinchers should be checked for

damage and kept clean.

NOTICE

Keep moisture away from the tool.

►After removing the battery from tool, clean the area of the clinchers, base plate, box detection

and magazine with a clean rag. For better access, remove magazine (see Section “6.4”).

If necessary, clean/replace the driver blade/clinchers (see Section “6.5”/“6.6”).

6.3 Removing jammed staples

►Remove battery from tool.

►Remove magazine (see Section “6.4”).

►If necessary, remove rear body (see Section “6.5”).

►If necessary, remove protection plate.

►Using a pair of pliers, remove the jammed staple.

►Reinstall parts and insert battery.

EN 20

PREVENTIVE AND CORRECTIVE MAINTENANCE

6.4 Removing/installing the magazine

Removing

►Remove battery from tool.

►Press the quick release buttons on left and right side (1) on the

stapler and pull the magazine (2) backwards (a) and afterwards

pull it downwards (b).

Installing

►Installing is performed in reverse order.

►When installing the magazine make sure that the quick release

buttons (1) are ush with the housing.

→Only then the latching of the magazine is ensured and no

malfunction (stable jam) can occur as a result.

6.5 Cleaning/replacing the driver blade (pos. 3)

Required parts Order number

c.561B /c.561B22: Driver blade (wear part) 164175

a.560B: Driver blade (wear part) 164176

a.560B22: Driver blade (wear part) 164177

Cylinder screw Torx, M4 (1) 946876

Dismantling

►Remove battery from tool.

►Remove magazine (see Section “6.4”).

►Set penetration depth to MIN (see

Section “5.5”).

►Loosen six captive cylinder screws Torx

(1) holding the rear body to the front

section.

►Pull down the rear body (2) and remove

it.

►Remove driver blade (3).

►Clean and check driver blade for wear,

if necessary replace it.

Fitting

►Fitting is performed in reverse order.

►When installing the driver blade, make

sure that the signage “visible while

assembling” (4) points outwards.

Page is loading ...

Josef Kihlberg a.560B22CL User manual

Brand: Josef Kihlberg

Model: a.560B22CL

Category: Power tools

Type: User manual

Download PDF

report

in other languages

svenska: Josef Kihlberg a.560B22CL Användarmanual

Josef Kihlberg a.560B22CL User manual

Josef Kihlberg a.560B22CL User manual

in other languages

Related papers

Other documents