Kutai DSP-10 Owner's manual

Brand: Kutai

Model: DSP-10

Type: Owner's manual

KUTAI ELECTRONICS INDUSTRY CO., LTD.

TEL : +886-7-8121771 FAX : +886-7-8121775 Website : www.kutai.com.tw

Headquarters : No.3, Ln. 201, Qianfu St., Qianzhen Dist., Kaohsiung City 80664, Taiwan

DSP-10

Genset Multi-Function Display Module

Model DSP-10 is a small integrated digital display showing

Voltage, Amp, Hz, and Hour Meter. It can be used

individually or jointly with a GCU-10 (Automatic Engine

Control Module) and a GCU-11R (Relay Module); jointly they

reduce cost, and installation time, simplifying equipment set

up.

This attractive little display is multitalented and its uses are

only limited by your imagination. It is equipped with DIN

terminal plugs that improve serviceability. The DSP-10

display can be used in any number of applications where

accurate reading of Voltage, Amps and Hertz are needed.

Front Panel Layout and Operation

DSP-10 Display panel

has three four Digits

bright LED’s that

shows (RMS) Voltage -

Amps – Hertz – Hour

Meter and Battery

Voltage. The operator

can change the display

to be fixed or cycling

from phase to phase

by simply using the

button next to each

display.

To change the display mode, press the button next to it. See

diagram.

Running Hour (Hr) Reset

To reset the Engine Running Hour to zero, press (Func)

button on the front panel until the (Hr) mode is displayed, and

then press (V) + (A) button together for 5 seconds erasing the

EEPROM and the hour meter back to zero.

Rear Panel Layout

Recommended Cut-Out 66 66 ± 0.5 mm

Voltage and Current Adjustment (If Need)

In the back of the DSP-10 module we have 4 push buttons for

voltage 【V & V】 and current 【A & A】 adjustment.

The Module comes factory tested and calibrated and

normally no changes are necessary. But if any modifications

are required, follow the procedures below.

Voltage Adjustment

(Please use and accurate RMS Voltmeter as your

reference)

1. Start the generator. Set your reference AC voltage using

your Voltmeter.

2. Select the desire phase you need to re-calibrate using the

front display V button on the display and hold.

3. Repeatedly press V) or V on back of module to

adjust the displayed voltage equivalent to your voltmeter.

4. Release the front V button. The LED display will flash

continuously for 5 seconds.

5. After for 5 seconds then the system will automatically

record the new setting and return to normal.

6. If the display shows FAIL the setting is invalid, and step

3 must be repeated.

Current Adjustment Procedure

(Please use Standard RMS Current meter for readings)

1. Set the dip switches to the correct CT in use.

2. Start the generator. And wait for the generator to stabilize.

3. Slowly add load to the genset until maximum rated load

current is reached for the CT in use.

4. Select desire phase current to calibrate using the front A

button.

5. Repeatedly press A or A on the back panel to

adjusts the displayed current to its equivalent on the

current meter.

6. Release the front A button. The LED on the display will

flash continuously for 5 seconds.

7. After 5 seconds the system will automatically record the

new setting and return to normal.

8. If the panel display shows FAIL then the previous

setting is invalid, please return to step 5.

L23 Fix Mode

L31 Fix Mode

L12 Fix Mode

Cyclic Mode

Setting The CT Value

Set the 5 pin dip switch for the CT (Current Transformer) and

the system phase you are using.

DIP Switch Setting Reference Diagram

50/5A

100/5A

150/5A

200/5A

250/5A

300/5A

400/5A

500/5A

600/5A

800/5A

1000/5A

1200/5A

1500/5A

1600/5A

2000/5A

3000/5A

Programmer Table =ON =OFF

System Phase select 5

= 3 Phase

= 1 Phase

1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4

Current Transformer (CT)

Specification

ITEM

DESCRIPTION

DC Supply

9.0  36 Vdc

Alternator Input Range

10  500 Vac (Ph-Ph)

Alternator Input Frequency

50/60 Hz

CT Burden

Above 2.5VA

CT Secondary

Max. CT Rated

3000A / 5A

Operating Temperature

-20 to 60 ˚C

Relative Humidity

Under 90 %

Power Consumption

Under 2W

Weight

179 g +/- 2%

Three Phase System Standard Wiring Diagram

Single Phase System Standard Wiring Diagram

Please link to http://www.kutai.com.tw for detailed manual

LOAD

CT-L3

GL2

Battery

Emergency Stop

Accessory

J3-10

L1L3 L2

J3-1 J3-3J3-2

NV+

J3-4 J3-11

V-

J3-12

0.5A0.5A

0.5A

"ON"

Stop

Start

Pre-Heat

J3-5 J3-6 J3-8J3-7 J3-9

35A

35A 35A

Pre-Heat

Start

Stop

Temp SW

OIL SW

Remote Start

AUX. Alarm

J1-5

J4-8J4-1 J4-3J4-2

L2 L1L3

J1-6 J1-2J1-4

J4-5J4-4 J4-6 J4-7

V+V-

J2-8J2-9 J1-1 J1-2

J2-12 J2-13

J2-15J2-14

J4-9J4-13 J4-12 J4-10 J4-11

J1-4J1-6 J1-7

J2-11 J2-10

5A5A 5A

J2-13J1-3 J2-8J2-12 J2-9

GCU-10 GENERATOR CONTROL UNIT

Governor

Electronic

Idle Control

Idle control

J2-15J2-14

K L

CT-L1

CT-L2

GCU-11R

DSP-10 Meter

Advance Terminals

For DSP-11 Module

F2F3 F1

J4-1 J4-3J4-2

GCU-11R

J4-5J4-4 J4-6 J4-7

35A35A 35A

"ON"

Stop

Start

Pre-Heat

J3-6J3-5 J3-9J3-7 J3-8

35A

J4-9

Pre-Heat

J4-13 J4-12

Start

Stop

J4-10 J4-11

Temp SW

OIL SW

Emergency Stop

Remote Start

AUX. Alarm

J1-5

DSP-10 Meter

J1-6

J1-4 J1-2

L1L2

J2-12

J2-8

V+

J2-9

V-

J1-1 J1-2

J2-15

K L

CT-L1

GCU-10 GENERATOR CONTROL UNIT

5A5A 5A5A

J1-4J1-6 J1-7 J2-11 J2-10 J1-3 J2-13 J2-8J2-12 J2-9

Electronic

Governor

Idle Control

Idle control

J2-15J2-14

Advance Terminals

For DSP-11 Module

Accessory

Battery

LOAD

GL1

J3-10

J4-8

L1L2

J3-3J3-2J3-1

V-V+

J3-4 J3-12J3-11

0.5A0.5A 0.5A

Kutai DSP-10 Owner's manual

Kutai DSP-10 Owner's manual

Kutai DSP-10 Owner's manual

Related papers

Other documents