QSC Audio CX702 User manual

EN

CH

DE

FR

ES

CX Series User Manual

Installed Sound Professional Audio Amplifiers

2-Channel Low-impedance Models:

CX302

CX502

CX702

CX902

CX1102

4-Channel Low-impedance Models:

CX254

CX404

70 Volt Direct Output Models:

CX204V (4-channel)

CX302V (2-channel)

CX602V (2-channel, 8 ohm capable)

CX1202V (2-channel, 4 and 8 ohm capable)

*TD-000077-00*

TD-000077-00 Rev.G

EN

2

Important Safety Precautions & Explanation of Symbols

1- Read these instructions.

2- Keep these instructions.

3- Heed all warnings.

4- Follow all instructions.

5- WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture. Do not use this apparatus near water.

6- Clean only with a dry cloth.

7- Do not block any ventilation openings.

8- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other.

A grounding plug has two blades and a grounding prong. The wide blade or third prong are provided for your safety. If the provided plug

does not fit your outlet, consult an electrician for the replacement of the obsolete outlet.

10- Protect the power cord from being walked on or pinched, particularly plugs, convenience receptacles, and the point where they exit

from the apparatus.

11- Use only attachments/accessories specified by QSC Audio Products, LLC

12- Use only with hardware, brackets, stands, and components sold with the apparatus or by QSC Audio Products, LLC

13- Unplug the apparatus during lightning storms or when unused for long periods of time.

14- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as

power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to

rain or moisture, does not operate normally, or has been dropped.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and main-

tenance (servicing) instructions in this manual.

The lightning flashes printed next to the OUTPUT terminals of the amplifier are intended to alert the user to the risk of hazardous

energy. Output connectors that could pose a risk are marked with the lightning flash. Do not touch output terminals while amplifier

power is on. Make all connections with amplifier turned off.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsu-

lated "dangerous" voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock

to humans.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED PERSONNEL.

WARNING: To prevent fire or electric shock, do not expose this equipment to rain or moisture.

FCC INTERFERENCE STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio

frequency energy and if not installed and used in accordance to the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by switching the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio or TV technician for help.

QSC® is a registered trademark of QSC Audio Products, LLC

"QSC" and the QSC logo are registered with the U.S. Patent and Trademark Office

All trademarks are the property of their respective owners.

EN

3

Introduction

Thank you for purchasing this QSC power amplifier. Please read the following directions to obtain the best results.

The CX model line-up features:

•2 channel and 4 channel low-impedance or transformerless 70V output models

•Each channel pair has its own DataPort and Mode Switch

•QSC DataPorts connect to the most advanced QSC accessories and monitoring systems

•Mode switches for Clip Limit, Low Frequency Filter, Stereo, Bridge Mono, and Parallel Inputs

•QSC PowerLight high-performance, compact, and light weight switching power supply

•Complete amplifier protection and monitoring

•Barrier strip output connectors

•XLR and terminal block balanced input connectors

•Gain controls are recessed and detented

•Security cover for gain controls prevents tampering

•Active inrush current limiting eliminates need for power sequencing

•LED indicators for power, parallel or bridge mode, input signal presence, -20dB, -10dB, and clip/protect

•Optional front panel handles

•Optional IT-42 isolated output transformer for CX302 for 25V, 70V, and 100V (or 50V, 140V, and 200V bridge mode)

Unpacking

Factory packed carton contains:

•CX amplifier

•User's manual

•Security cover for gain controls

•Adhesive rubber feet (for non-rack mount applications)

•3-pin terminal block input connectors

•Spade lug output connectors

•IEC-type detachable power cord

Use the same type carton when shipping the amplifier.

Front Panel

(CX404 shown, other models similar)

1- Power Switch

2- Cooling Air Exhaust Vents

3- LED Indicators

4- Security Panel Retaining Screw

5- Gain Controls

6- Security Panel Retaining Slots

EN

4

Rack Mounting

Optional handles shown. Use four screws and washers to mount

the amplifier to the equipment rack rails. To use the

amplifier outside a rack, attach the self-adhesive

rubber feet to the bottom.

Cooling

Air flows from the rack, into the back of the amplifier,

and out the front. This keeps the rack cool. The fan

automatically runs faster when the amp is working

hard.

Do not block the front or rear air vents!

AC Mains Connection

Connect AC power to the IEC socket on the back of the amplifier. NOTE: Turn off the AC power switch before connecting AC power. The

AC Switch must be turned on to use remote control systems or the Standby function.

The correct AC line voltage is shown on the serial number label, on the rear panel. Connecting to the wrong line volt-

age may damage the amplifier or increase the risk of electric shock.

Air flow in QSC amplifiers: Cool air is drawn

into the rear of the amplifier by the cooling fan.

Warm air exits the front of the amplifier.

1- CH1 Terminal Block Input Connectors

2- DataPort Connector

3- CH2 Terminal Block Input Connectors

4- Mode Switches

5- Barrier Strip Output Connectors

6- Cooling Air Inlet Vents

7- Mode Switch Setting Diagrams

8- IEC Power Connector

Rear Panel

(CX404 shown, other models similar, 2-Ch. models equipped with XLR inputs as well)

EN

5

Stereo Mode - Switches 4, 5, 6

and 7 are all set to the DOWN

position.

Parallel Mode - Switches 4, 5,

and 6 are set to the UP position.

Switch 7 is set to the DOWN

position.

Bridge Mode- Switches 4, 5, 6

and 7 are all set to the UP posi-

tion.

Low Frequency Filter (“V” model

shown): Each channel has its

own switches for LF filter on/off

and frequency selection.

•The first channel uses switches

2,3. The second channel uses

switches 8,9.

•Switches 3 and 8 turn the LF fil-

ter ON or OFF.

•Switches 2 and 9 select 33/75 Hz

(low Z) or 50/75 Hz (“V” models)

or 75 Hz.

•On four-channel models, the

second mode switch has

switches for Ch.3 and Ch.4

Setting the Mode Switches

Two-Channel Models: One mode switch controls each channel’s indepen-

dent clip limiting and low frequency (LF) filtering. The switches can set the

amplifier’s operating mode for Stereo, Parallel, or Bridge operation.

Four-Channel Models: There are two mode switches; one controls the

operation of channels 1-2, the other controls the operation of channels 3-4.

It is not possible to bridge or parallel channels 1 or 2 with channels 3 or 4.

Setting Clip Limiters

Each channel has a clip limiter with its own on-off switch. The limiter only

responds to actual clipping, and automatically compensates for load and

voltage variations. Clip limiting is generally recommended, especially to

protect high frequency drivers.

Set switch UP (ON position) to use Clip Limiting.

Switch 1 controls the first channel.

Switch 10 controls the second channel.

Selecting Stereo, Parallel, or Bridge Mode

Each of the channel pairs can be set for normal Stereo operation, Parallel

Input mode, or Bridge Mono mode. On four-channel models, Ch.1 can be

bridged or paralleled with Ch.2; Ch.3 can be bridged or paralleled with Ch.4.

Stereo Mode- Each channel within the pair remains independent, and

each may be used for a different signal.

Parallel Mode - This setting connects both inputs of a pair together. One

signal feeds both channels. Do not connect different sources to each input.

Each channel's Gain control and speaker connection remain independent.

Bridge Mode- This setting combines both channels of a pair into a single

channel with twice the output voltage. Use only the first channel's input

and Gain control. Set the second channel's Gain control at minimum.

Do not connect different inputs to each side of a channel pair

when operating in parallel or bridge mode.

Setting Low Frequency Filters

Each channel has a 12dB per octave Low Frequency filter that can be set on

or off. Low impedance models can be set for 33 or 75 Hertz and distributed

output (“V” models) for 50 or 75 Hertz to prevent saturation of the 70V

speaker transformers. This reduces distortion and prevents amplifier over-

load.

Low Impedance Models: The filter should only be turned off for driving

subwoofers. The 33 Hz setting usually works well with loudspeakers that

have large LF drivers (12” or larger). The 75 Hz setting works well with com-

pact (smaller size) loudspeakers. Check the loudspeaker’s specifications and

select the setting closest to the loudspeaker’s low frequency capability.

High Impedance (“V”) Models: The filter should only be turned off for

driving subwoofers with special low frequency transformers. The 50 Hz set-

ting usually works well with high quality speaker transformers. The 75 Hz

setting works well with speech-grade speakers and transformers.

Each channel has its own switch

for Clip Limiter on/off.

The first channel uses switch 1.

The second channel uses switch

10. On four-channel models, the

second mode switch has

switches for Ch.3 and Ch.4

Typical Mode Switch block as

seen from the rear of the amplifier

(CX404V model shown).

EN

6

DataPort

Two-channel models have one DataPort, four-channel models have two DataPorts (one Ch.1-2, one for Ch.3-4).

The DataPort connects to optional QSC accessories and processing devices. DataPort devices provide remote

Standby control, monitoring, DSP processing, filter and crossover functions. The CX’s DataPort supports the full

"V1" DataPort feature set. Two-channel models support directly-mounted DSP “modules”. Four channel models

require remote mounting of accessory modules connected with DataPort cables.

Each DataPort connects to its respective channel pair; Ch.1-2 or Ch.3-4. Each channel pair may use its DataPort

or the Terminal Block inputs. When using the DataPort, do not connect to that channel's Terminal Block inputs.

Amplifier Standby is controlled only by the Ch.1- 2 DataPort.

DataPort Tips:

1- DataPort 1-2 controls Standby for the entire amplifier. The AC switch must be turned ON before the DataPort

can control the power.

2- Each DataPort controls and monitors the signals to its respective channel pair (Ch.1-2, Ch.3-4).

3- Do not use the Bridge Mono or Parallel mode switches when using DataPort Inputs. The signal level may be reduced. For more infor-

mation, see the Owner's Manual for the DataPort device.

4- A DataPort device is normally used to control the signal gain before entering the amplifier. Set the front panel Gain controls at max-

imum after confirming correct operation. If desired, install the protective cover to prevent tampering.

5- Each channel uses a separate internal heat sink. The heat sink temperatures are reported on that pair's DataPort.

6- Consult your QSC dealer or the QSC web site for the latest DataPort products.

Inputs

Each channel has a balanced 3-pin terminal block input. Two channel models also feature XLR inputs. The input impedance is 12k ohm

balanced or 6k ohm unbalanced. A set of terminal block connectors is included in the carton. Terminal block wiring is connected with

simple hand tools, and inputs can be changed quickly. XLR inputs are connected with standard cables and can be changed quickly.

Pinouts are marked on the rear panel.

Balanced connections are recommended to reduce AC hum and interference, especially with long cable runs. Unbalanced connections

may be suitable for short cables. The signal's source impedance should be less than 600 ohms. If the DataPort is being used for input

signals, do not connect cables to the terminal blocks.

Terminal Block Connectors

Balanced inputs: Strip the wires ¼ inch (6mm) and connect to the plug

as shown. Be sure to tighten the screws firmly.

Unbalanced inputs: Strip the wires ¼ inch (6mm) and connect to the

plug as shown. The middle pin must be connected to the shield pin as

shown. Be sure to tighten the screws firmly.

XLR Inputs (2-Ch. models only)

Balanced inputs: Connect to the plug as shown.

Unbalanced inputs: Connect to the plug as shown.

Pin 3 and pin 1 must be connected with a jumper as

shown.

DataPorts on a 4-Ch. amplifier.

EN

7

70V stereo or parallel

connection- Each 70V

zone connects to its

respective channel.

Ensure that all speaker

connections maintain

proper polarity.

140V Bridge connection-

Wire each bridged pair to

a 140V circuit as shown.

Check for proper polarity.

Outputs

Wiring connections are shown on the back of the chassis. Carefully note the

polarity marks, which are arranged to make Bridge Mode connections easier.

Four-channel models are shown in the examples; two-channel models are similar.

OUTPUT TERMINAL SAFETY WARNING! Do not touch output termi-

nals while amplifier power is on. Make all connections with ampli-

fier turned off. Risk of hazardous energy!

Low Impedance Outputs

Stereo and Parallel Mode- Connect each loudspeaker to its own channel of

the amplifier, as shown on the chassis label. The mode configuration switches

must be set for Stereo or Parallel mode.

Bridge Mode- Bridge mode configures the channel pair to drive a single high-

power loudspeaker load. The mode configuration switches must be set for Bridge

mode. Use only the first channel's input and Gain control. Set the second chan-

nel's Gain control at minimum.

Distributed Outputs (“V” models, 70V/140V)

Stereo and Parallel Mode- Connect each 70V circuit to its own channel of the

amplifier, as shown on the chassis label. The mode configuration switches must

be set for Stereo or Parallel mode.

70V Output- Risk of hazardous energy! Class 2 wiring shall be used

for 70V outputs.

Bridge Mode- Bridge mode configures the channel pair to drive a single 140V

audio circuit. The mode configuration switches must be set for Bridge mode. Use

only the first channel's input and Gain control. Set the second channel's Gain

control at minimum. Connect the load as shown on the chassis label.

140V BRIDGE MODE PRECAUTIONS:

Class 3 Wiring shall be used for bridged mono 140V outputs.

Connect only 140V distributed audio circuits in bridged mode. Do not

use 70V loads in bridge mode! Use Stereo or Parallel mode channels

to drive 70V loads. 140V is the minimum for bridge mode operation.

Low Impedance Stereo or

Parallel Connection- Each

loudspeaker load con-

nects to its respective

channel. Four channel

model shown. Ensure that

all speaker connections

maintain proper polarity.

Low Impedance Bridge

Connection- Each loud-

speaker load connects to a

bridged channel pair. Four-

channel model shown.

Check for proper polarity.

Loads Rated by Model

Be sure the model

amplifier you are using

is rated for the load!

An asterisk (*)indicates the

model is rated for the load.

(S/P)= Stereo/Parallel mode

(Br.)= Bridge mode

EN

8

LED Indicators

The LED indicators can be used to monitor system operation and identify common prob-

lems.

POWER: GREEN, above the BRIDGE (BRDG) and PARALLEL (PAR) indicators.

Normal indication: AC switch ON: LED will illuminate.

If no indication: Check AC power cord and AC outlet. Confirm that DataPort 1-2 is

not holding the amp in 'Standby' mode.

CLIP: RED, adjacent the channel number markings.

Normal indication: illuminates whenever the amplifier is driven beyond full power.

The resulting distortion corresponds to the brightness of the LED. Distortion that

causes only brief flashing may not be audible.

-During muting, the LED fully illuminates. This occurs during normal "On-Off" muting.

Abnormal indication:

-Bright red illumination while the amp is being used indicates either thermal muting

or a shorted output.

-If the amplifier overheats, the fan will run at full speed, and operation should resume

within one minute. Allow the fan to run, and make sure the amplifier ventilation is

adequate.

-A shorted or overloaded output circuit will cause excessive Clip flashing and possible

overheating.

If distortion is audible without a Clip indication, the problem is either before or after

the amplifier. Check for damaged speakers or overloaded signal source. The amplifier

Gain control should be in the upper half of its range to prevent input overload.

SIGNAL, -20dB, -10dB: GREEN, under each Clip LED.

Normal indication: The SIGNAL indicator illuminates when the input signal exceeds

-35 dB, the -20dB indicator illuminates when the signal exceeds -20dB, and the -10dB

indicator illuminates when the signal exceeds -10dB.

If no indication: check Gain settings and increase gain if necessary. Check input con-

nections and audio source for signal. If the Clip LED illuminates with little or no Signal

indication, check the output wiring for shorts.

Abnormal indication: If the SIGNAL (SIG), -20dB, or -10dB LED illuminates with no

signal input, there may be system oscillations or some other malfunction. Disconnect

the load and fully reduce the gain. If the LED remains on, the amp may need servicing.

BRDG and PAR:

Each channel pair has a YELLOW LED for Bridge Mode, and an ORANGE LED for Paral-

lel mode. These show how the rear panel switches are set (see Setting the Mode

Switches). In Stereo mode, both LEDs should be OFF.

LED indicators on 2-channel models.

LED indicators on 4-channel models.

EN

9

Gain Controls

The Gain controls are recessed and can be adjusted with

a small screwdriver or flat tool. If desired, the Gain Con-

trol Security Cover can be installed to prevent changes

to the installer's settings.

Turn the gain controls clockwise to increase gain and

counter clockwise to decrease gain. The maximum volt-

age gain of the amplifier varies depending on the model

designation. Maximum voltage gain for each model is

shown on the front panel label in parentheses adjacent

the 0dB attenuation setting.

The Gain controls are marked in dB of attenuation. There

are 21 detents for repeatable adjustments. The upper 14

steps are about 1 dB each, and settings should normally

be made within this range. The range below -14 dB

should not be used for normal program levels, as the

input headroom could be exceeded, but can be used for

testing at reduced levels. At the minimum setting, the

signal is completely cut off.

Gain Control Security Plate

The cover blocks access to the Gain settings. The LED

indicators are still visible to monitor the system's opera-

tion.

1. Use a 9/64" or 3.5 mm hex driver to loosen the screw

several turns. Do not remove it completely.

2. Slide the right end of the cover under the loosened

screw.

3. Insert the left end tabs into the last row of ventilation

slots, and slide the panel fully to the right. It should

lock into the slots.

4. Confirm that the LED's are visible through the cover.

Tighten the hex screw carefully.

Gain controls on 2-channel models.

Markings will vary depending on model.

Gain controls on 4-channel models.

Markings will vary depending on model.

CX902 shown with gain control security plate installed.

EN

10

Specifications 2-Channel Low-Impedance Models

CX302 CX502 CX702 CX902 CX1102

OUTPUT POWER (Watts)

20 - 20k Hz, 0.03% THD, 8 Ohms/Ch. 200 300 425 550 700

20 - 20k Hz, 0.05% THD, 4 Ohms/Ch. 325 500 700 900 1100

1k Hz, 1.0% THD (EIA), 8 Ohms/Ch. 215 325 475 625

1k Hz, 1.0% THD (EIA), 4 Ohms/Ch. 375 550 825 1050

1k Hz, 1.0% THD (EIA), 2 Ohms/Ch. 600 800 1200 1500 1700

Bridge Mono, 20 - 20k Hz, 0.1% THD, 16 Ohms 400 600 850 1100 1400

Bridge Mono, 20 - 20k Hz, 0.1% THD, 8 Ohms 700 1000 1500 2000

Bridge Mono, 1k Hz, 1.0% THD, 8 Ohms

Bridge Mono, 1k Hz, 1.0% THD, 4 Ohms 1200 1600 2400 3000 3400

DISTORTION, SMPTE-IM <0.01% <0.01% <0.02% <0.02% <0.02%

FREQUENCY RESPONSE 20 - 20k Hz, ±0.2dB at 10dB below rated output power, all models (-3dB points: 8 Hz and 100 kHz)

SIGNAL to NOISE, unweighted, 20 - 20k Hz -106 dB -107 dB -106 dB -104 dB -106 dB

VOLTAGE GAIN 31.5x (30dB) 40.0x (32dB) 50.5x (34dB) 56.6x (35dB) 56.6x (35dB)

INPUT SENSITIVITY, Vrms

for rated power into 8 Ohms 1.26 (+4.2dBu) 1.23 (+4.0dBu) 1.16 (+3.5dBu) 1.17 (+3.6dBu) 1.35 (+4.8dBu)

for rated power into 4 Ohms 1.14 (+3.4dBu) 1.12 (+3.2dBu) 1.05 (+2.6dBu) 1.06 (+2.7dBu) 1.17 (+3.6dBu)

OUTPUT CIRCUIT TYPE AB AB H H H

INPUT IMPEDANCE 6k ohms unbalanced, 12k ohms balanced, all models

DYNAMIC HEADROOM 2 dB at 4 Ohms, all models

DAMPING FACTOR >500 at 8 Ohms, all models

AMPLIFIER PROTECTION Short circuit, open circuit, thermal, ultrasonic and RF protection. Stable into reactive or mismatched loads

COOLING Continuously variable speed fan; back-to-front air flow through heat sink tunnel

CONTROLS Front: AC POWER switch, gain controls (1 control per channel, 21 detents)

Back: 10-position DIP switch with Clip Limiter (1 per Ch.), LF Filter on/off (1 per Ch.)

LF filter select: 33 or 50 Hz (1 per Ch.), Stereo/Parallel/Bridge mode selection switches

LED INDICATORS POWER (green, 1 each), SIGNAL, -10dB, -20dB (green, 1 each per Ch.), CLIP (red, 1 each per channel),

BRDG and PAR (yellow, 1 each)

CONNECTORS Input: 3-pin terminal blocks ("euro" or "Phoenix" type) and XLRs (pin 2 positive)

Output: barrier strip connectors with protective shroud

Other: QSC DataPort connector (supports full “V1”feature set)

LOAD PROTECTION Turn-on/turnoff muting, AC coupling (DC fault blocking), Clip limiting.

POWER REQUIREMENTS Refer to rear panel serial number label. Configured at factory for 100, 120 or 220-240 VAC, 50- 60 Hz.

DIMENSIONS 19.0" (48.3 cm) W, 3.5" (8.9 cm) H, 14" (35.6 cm) D (from front mounting rails, including rear support ears)

WEIGHT 21 pounds (9.5 kg) net; 27 pounds (12.3 kg) shipping

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

EN

11

Specifications 4-Channel Low-Impedance Models

CX254 CX404

OUTPUT POWER (Watts)

20 - 20k Hz, 0.03% THD, 8 Ohms/Ch. 170 250

20 - 20k Hz, 0.05% THD, 4 Ohms/Ch. 250

1k Hz, 1.0% THD (EIA), 8 Ohms/Ch.

1k Hz, 1.0% THD (EIA), 4 Ohms/Ch. 450

1k Hz, 1.0% THD (EIA), 2 Ohms/Ch. 450

Bridge Mono, 20 - 20k Hz, 0.1% THD, 16 Ohms 340 500

Bridge Mono, 20 - 20k Hz, 0.1% THD, 8 Ohms 500

Bridge Mono, 1k Hz, 1.0% THD, 8 Ohms 900

Bridge Mono, 1k Hz, 1.0% THD, 4 Ohms 900

DISTORTION, SMPTE-IM <0.01% <0.01%

FREQUENCY RESPONSE 20 - 20k Hz, ±0.2dB at 10dB below rated output power, all models (-3dB points: 8 Hz and 100 kHz)

SIGNAL to NOISE, unweighted, 20 - 20k Hz -106 dB -106 dB

VOLTAGE GAIN 29.0x (29dB) 36.5x (31dB)

INPUT SENSITIVITY, Vrms

for rated power into 8 Ohms 1.28 (+4.4dBu) 1.22 (+3.9dBu)

for rated power into 4 Ohms 1.08 (+2.9dBu) EIA: 1.16 (+3.5dBu)

OUTPUT CIRCUIT TYPE AB AB

INPUT IMPEDANCE 6k ohms unbalanced, 12k ohms balanced, all models

DYNAMIC HEADROOM 2 dB at 4 Ohms, all models

DAMPING FACTOR >500 at 8 Ohms, all models

AMPLIFIER PROTECTION Short circuit, open circuit, thermal, ultrasonic and RF protection. Stable into reactive or mismatched loads

COOLING Continuously variable speed fan; back-to-front air flow through heat sink tunnel

CONTROLS Front: AC POWER switch, gain controls (1 control per channel, 21 detents)

Back: 10-position DIP switch (1 per channel pair) with Clip Limiter (1 per Ch.), LF Filter on/off (1 per Ch.)

LF filter select: 33 or 50 Hz (1 per Ch.), Stereo/Parallel/Bridge mode selection switches (1 set per Ch. pair)

LED INDICATORS POWER (green, 1 each), SIGNAL, -10dB, -20dB (green, 1 each per Ch.), CLIP (red, 1 each per channel),

BRDG and PAR (yellow, 1 each per Ch. pair)

CONNECTORS Input: 3-pin terminal block ("euro" or "Phoenix" type)

Output: barrier strip connectors with protective shroud, one barrier strip per Ch. pair

Other: two QSC DataPort connectors (supports full “V1”feature set), one DataPort per Ch. pair

LOAD PROTECTION Turn-on/turnoff muting, AC coupling (DC fault blocking), Clip limiting.

POWER REQUIREMENTS Refer to rear panel serial number label. Configured at factory for 100, 120 or 220-240 VAC, 50- 60 Hz.

DIMENSIONS 19.0" (48.3 cm) W, 3.5" (8.9 cm) H, 14" (35.6 cm) D (from front mounting rails, including rear support ears)

WEIGHT 21 pounds (9.5 kg) net; 27 pounds (12.3 kg) shipping

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

EN

12

Specifications 2- and 4-Channel Distributed 70V Line Models

CX204V CX302V CX602V CX1202V

OUTPUT POWER (Watts)

20 - 20k Hz, 0.03% THD, 70V/Ch. 200 200 400 800

20 - 20k Hz, 0.03% THD, 8 Ohms/Ch. 550 700

20 - 20k Hz, 0.05% THD, 4 Ohms/Ch. 1100

1k Hz, 0.05% THD (EIA), 70V/Ch. 220 250 440 1000

1k Hz, 0.1% THD (EIA), 70V/Ch. 300 600 1200

1k Hz, 1.0% THD (EIA), 70V/Ch. 300

Bridge Mono, 140V, 20 - 20k Hz, 0.1% THD 400 400 800 850

Bridge Mono, 140V, 1k Hz, 0.1% THD 440 600 1200 2400

Bridge Mono, 1k Hz, 0.1% THD, 16 Ohms 1200 1400

Bridge Mono, 1k Hz, 0.1% THD, 8 Ohms 2300

DISTORTION, SMPTE-IM <0.02%, all models

FREQUENCY RESPONSE 20 - 20k Hz, ±0.2dB at 10dB below rated output power, all models (-3dB points: 8 Hz and 100 kHz)

SIGNAL to NOISE, unweighted, 20 - 20k Hz -106 dB. all models

VOLTAGE GAIN 56.6x (35dB) all models

INPUT SENSITIVITY, Vrms 1.26V (+4.2dBu) for rated power at 70.7V

OUTPUT CIRCUIT TYPE AB AB AB H

INPUT IMPEDANCE 6k ohms unbalanced, 12k ohms balanced, all models

DYNAMIC HEADROOM 2 dB at 4 Ohms, all models

DAMPING FACTOR >500 at 8 Ohms, all models

AMPLIFIER PROTECTION Short circuit, open circuit, thermal, ultrasonic and RF protection. Stable into reactive or mismatched loads

COOLING Continuously variable speed fan; back-to-front air flow through heat sink tunnel

CONTROLS Front: AC POWER switch, gain controls (1 control per channel, 21 detents)

Back: 10-position DIP switch with Clip Limiter (1 per Ch.), LF Filter on/off (1 per Ch.)

LF filter select: 33 or 50 Hz (1 per Ch.), Stereo/Parallel/Bridge mode selection switches

LED INDICATORS POWER (green, 1 each), SIGNAL, -10dB, -20dB (green, 1 each per Ch.), CLIP (red, 1 each per channel),

BRDG and PAR (yellow, 1 each)

CONNECTORS Input: 3-pin terminal blocks ("euro" or "Phoenix" type)and XLRs (pin 2 positive)

Output: barrier strip connectors with protective shroud

Other: QSC DataPort connector (supports full “V1”feature set)

LOAD PROTECTION Turn-on/turnoff muting, AC coupling (DC fault blocking), Clip limiting.

POWER REQUIREMENTS Refer to rear panel serial number label. Configured at factory for 100, 120 or 220-240 VAC, 50- 60 Hz.

DIMENSIONS 19.0" (48.3 cm) W, 3.5" (8.9 cm) H, 14" (35.6 cm) D (from front mounting rails, including rear support ears)

WEIGHT 21 pounds (9.5 kg) net; 27 pounds (12.3 kg) shipping

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

EN

13

Thermal Loss Table

This table provides typical thermal loss in BTU/

hr. and kcal/hr. for each model as a function of

load and output power level.

• 1/8 power (pink noise) represents typical pro-

gram with occasional clipping. Use this rating

for most applications.

• 1/3 power (pink noise) represents severe pro-

gram with heavy clipping.

• Full power (sine) are continuous sine wave

driven at 1% clipping.

Thermal or overcurrent cutback limits duration

of full power 2 Ohm operation.

Current Draw Table (in Amperes)

This table provides typical current draw for each model as a

function of load and output power level. Units of measurement

are Amperes r.m.s.

NOTE! Current draw shown is for 120 VAC line. For 230

VAC models, multiply values shown by 0.5 .

• 1/8 power (pink noise) represents typical program with occa-

sional clipping. Use this rating for most applications.

• 1/3 power (pink noise) represents severe program with heavy

clipping.

• Full power (sine) is continuous sine wave driven at 1% clipping.

• Thermal or overcurrent cutback limits duration of full power 2

Ohm operation.

Page is loading ...

QSC Audio Products, LLC 1675 MacArthur Boulevard Costa Mesa, California 92626 USA

How to Contact QSC Audio Products

Cómo comunicarse con QSC Audio Products

Comment prendre contact avec QSC Audio Products

Kontaktinformationen für QSC Audio Products

联系 QSC Audio Products

Mailing address: QSC Audio Products, LLC

1675 MacArthur Boulevard

Costa Mesa, CA 92626-1468 USA

Telephone Numbers: Main Number (714) 754-6175

Sales & Marketing (714) 957-7100 or toll free (USA only) (800) 854-4079

Customer Service (714) 957-7150 or toll free (USA only) (800) 772-2834

Facsimile Numbers:

Sales & Marketing FAX (714) 754-6174

Customer Service FAX (714) 754-6173

World Wide Web: www.qscaudio.com

E-mail: [email protected]

[email protected]

QSC Audio CX702 User manual

QSC Audio CX702 User manual

in other languages

Related papers

Other documents