Whirlpool WIXXL126 Owner's manual

1

GB

Instruction booklet

WASHING MACHINE

WIXXL 126

English

GB

Contents

Installation, 2-3

Unpacking, 2

Remove the transit fixings, 2

Levelling, 2

Water connections, 2

Drainage and electrical connections, 3

Technical Details, 3

Washing machine description, 4-5

Control panel, 4

LEDs, 5

Starting and programmes, 6

Briefly: starting a programme, 6

Programme table, 6

Personalisations, 7

Setting the temperature, 7

Setting the spin speed, 7

Options, 7

Detergents and laundry, 8

Detergent dispenser, 8

Maximum load size, 8

Precautions and advice, 9

General safety, 9

Disposal, 9

Saving energy and respecting

the environment, 9

Care and Maintenance, 10

Switching off the water or electricity supply, 10

Cleaning, 10

Caring for your appliance door and drum, 10

Cleaning the pump, 10

Checking the water inlet hose, 10

Troubleshooting, 11

Service, 12

Before calling for assistance, 12

WIXXL126-GB-indesit.p65 25/07/05, 16.271

2

GB

Keep this instruction manual in a safe place for future

reference. Should the appliance be sold, transferred or

moved, make sure the instruction manual

accompanies the washing machine to inform the new

owner as to its operation and features.

! Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking

1. Unpack the machine.

2. Check whether the machine has been damaged

during transport. If this is the case, do not install it and

contact your retailer.

Remove the transit fixings

IMPORTANT: Follow these instructions to remove the

TWO transit fixings (see Description for location).

Situated on either side of the

rear panel,

BOTH transit boltsBOTH transit bolts

BOTH transit bolts

MUST be rMUST be r

MUST be r

emoved beforemoved befor

emoved befor

e usee use

e use.

! Failure to do so may cause

damage to your machine.

It is important the transit bolt

and spacer (see pic) come out

intact.

1. Unscrew the bolt using a

13mm spanner.

2. STOP when 3 threads can be

seen.

3. Hold, slide sideways and pull

to remove.

4. For safety, insert one of the

the plastic covers (supplied with

your machine) over the hole.

! Repeat steps 1 to 4 to remove

the second transit bolt.

! Packaging materials are not

children’s toys.

Levelling

Your machine will be noisy if the two front feet are not

adjusted so that the machine stands firm and level.

! The machine should be levelled from side to side and

from front to back.

1. Move your machine into its final location.

- Take care not to trap or kink

the hoses.

2. Turn one or both front feet

anti-clockwise by hand until the

feet cannot be turned any more.

When adjusting the feet, use a

spirit level to check the machine

stands level, from side to side

and from front to back.

- The spring on each foot will stop them coming loose.

! If it is placed on a fitted or loose carpet, adjust the

feet in such a way as to allow enough room for

ventilation beneath the machine.

Water connection

Connecting the water inlet hose.

Remember that this is a cold-fill machine.

! Check that seal is in place

inside the hose end cap.

Before making the water connections to gas ¾ thread,

allow the water to run freely from the supply tap until it

is perfectly clear.

Screw the inlet end with the blue

cap onto the cold water supply

tap.

Turn the taps on and check for leaks: tighten if

necessary.

! Make sure there are no kinks or bends in the hose.

! The water pressure at the tap must be within the

values indicated in the Technical details table (next

page).

! If the water inlet hose is not long enough, contact a

specialist store or an authorised serviceman.

! Always use new hoses.

! Check the water hose at least once a year, replace

any that are cracked as worn hoses could split under

water pressure.

Installation

WIXXL126-GB-indesit.p65 25/07/05, 16.272

3

GB

Drainage connections

A. Connect the drain

hose, without kinking it,

to a draining duct or a

wall drain fixed at a

height between 65 and

100cm from the floor.

B. Alternatively, place it

over the edge of a basin,

sink or tub, fastening the

hose supplied to the tap.

The free end of the hose should not be under water.

! We advise against the use of hose extensions. In

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150cm in length.

Electrical connections

Before plugging the appliance into the mains socket,

make sure that:

• the socket is earthed and in compliance with the

applicable law.

• the socket is able to sustain the appliances

maximum power load indicated in the Technical

Details table (on the right).

• the supply voltage is included within the values

indicated in the Technical Details table (on the right).

• the socket is compatible with the washing machines

plug. If this is not the case, replace the socket or

the plug.

! The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to leave

it exposed to rain and thunderstorms.

! When the washing machine is installed, the mains

socket must be within easy reach and should be

connected to a suitable electrical supply.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or

dangerously compressed.

! The power supply cable must only be replaced by an

authorised serviceman.

! The company denies all liability if and when these

norms are not respected.

The first wash cycle

Once the appliance has been installed and before you

use it for the first time, run a wash cycle without

detergent and no laundry, setting the 90°C

programme without a pre-wash cycle.

B

A

WIXXL126-GB-indesit.p65 25/07/05, 16.273

TECHNICAL DETAILS

Model

WIXXL 126

Dimensions

59.5 cm wide

85 cm high

52.5 cm deep

Capacity

from 1 to 7 kg

Electric

connections

voltage 220 - 240 volts 50 Hz

Absorbed power 1700 - 2100 W

Water

connection

maximum pressure 1 MPa (10 bar)

minimum pressure 0,05 MPa (0,5 bar)

drum capacity 53 litres

Spin speed

up to 1200 rpm

Control

programmes

according to

the IEC456

directive

programme 2 with temperature set to

60°C run with a load of 7 kg.

This appliance is compliant with the

following European Community

directives:

- 73/23/CEE of 19/02/73 (Low Voltage)

and subsequent amendments

- 89/336/CEE of 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments

4

GB

Detergent dispenser

Control panel

Washing Machine Description

Detergent dispenser: to add detergent and fabric

softener (see page 8).

LEDS:

to find out which wash cycle phase is under

way.

If the Delay Timer option has been set, the time left

until programme starts will be indicated (see page 5).

SPIN SPEED knob: to set the spin speed or exclude

the spin cycle completely (see page 7).

OPTION buttons: to select the options available.

The button corresponding to the selected option will

remain on.

TEMPERATURE knob: to set the temperature or the

cold wash cycle (see page 7).

START/RESET button: to start the programmes or

cancel any incorrect settings.

ON-OFF/DOOR LOCK LED: to find out whether the

washing machine is on and if the appliance door can

be opened (see page 5).

ON/OFF button: to turn the washing machine on and

off.

PROGRAMME knob: to select the wash

programmes. The knob stays still during the cycle.

OPTION

Buttons

LEDs

ON-OFF/DOOR

LOCK LED

START/RESET

Button

ON/OFF

Button

PROGRAMME

Knob

SPIN SPEED

Knob

TEMPERATURE

Knob

WIXXL126-GB-indesit.p65 25/07/05, 16.274

5

GB

LEDs

The LEDs provide important information.

This is what they can tell you:

Delay set:

If the Delay Timer option has been enabled (see page

7), once you have started the programme, the LED

corresponding to the delay set will begin to flash:

As time passes, the remaining delay will be displayed,

and the corresponding LED will flash:

Once the set delay is complete, the flashing LED will

turn off and the programme set will start.

Cycle phase under way:

During the wash cycle, the LEDs gradually illuminate

on to indicate the cycle phase under way:

Prewash

Wash

Rinse

Spin cycle

Note: during draining, the LED corresponding to the

Spin cycle phase will be turned on.

Option buttons:

The OPTION buttons also act like LEDs.

When an option is selected, the corresponding button

is illuminated.

If the option selected is incompatible with the

programme set, the button will flash and the option

will not be enabled.

If you set an option that is incompatible with another

option you selected previously, only the last one

selected will be enabled.

ON-OFF / DOOR LOCK LED:

If the LED is on, the appliance door is locked to prevent it from being opened accidentally; to avoid any damages,

wait for the LED to flash before you open the appliance door.

! The rapid flashing of the ON-OFF/DOOR LOCK LED together with the flashing of at least one other LED indicates

there is an abnormality. Call for Technical Assistance.

WIXXL126-GB-indesit.p65 25/07/05, 16.275

6

GB

Briefly: starting a programme

1. Switch the washing machine on by pressing button .

All the LEDs will light up for a few seconds and the

ONOFF / DOOR LOCK LED will begin to flash.

2. Load your laundry into the washing machine and

shut the appliance door.

3. Set the PROGRAMME knob to the programme

required.

4. Set the wash temperature (see page 7).

Starting and Programmes

5. Set the spin speed (see page 7).

6. Add the detergent and any fabric softener (see page 8).

7. Start the programme by pressing the START/RESET

button for at least 2 seconds.

8. When the programme is finished, the ON-OFF /

DOOR LOCK LED will flash to indicate that the

appliance door can be opened. Take out your

laundry and leave the appliance door ajar to allow

the drum to dry thoroughly. Turn the washing

machine off by pressing the button

.

Programme table

Notes

- For Programmes 8 and 10, we advise against exceeding a wash load of 3.5 kg.

- For Programmes 13 and 9, we advise against exceeding a wash load of 2 kg.

- For the anti-crease option: see Easy Iron (opposite page). The information contained in the table is purely indicative.

Special programme

Daily (programme 11 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only

lasts 30 minutes and allows you to save on both time and energy. By setting this programme (11 at 30°C), you can

wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg.

We recommend the use of liquid detergent.

* To select a lower temperature (60° or 40°), the temperature reduction rotary is to be used.

WIXXL126-GB-indesit.p65 25/07/05, 16.276

Detergent

Type of fabric and degree of soil

Programmes

Tempe-

rature

Pre-

wash

Fabric

softener

Cycle

length

(minutes)

Description of wash cycle

Standard

Extremely soiled whites

(sheets, tablecloths, etc.)

1

90°

135

Pre-wash, wash cycle, rinse cycles,

intermediate and final spin cycles

Extremely soiled whites

(sheets, tablecloths, etc.)

2

90°

150

Wash cycle, rinse cycles,

intermediate and final spin cycles

Heavily soiled whites and fast colours

2

60°

*

140

Wash cycle, rinse cycles,

intermediate and final spin cycles

Heavily soiled whites and delicate colours

2

40°

*

105

Wash cycle, rinse cycles,

intermediate and final spin cycles

Slightly soiled whites and delicate colours

(shirts, jumpers, etc.)

3

40°

70

Wash cycle, rinse cycles,

intermediate and final spin cycles

Heavily soiled fast colours (baby linen, etc.)

4

60°

75

Wash cycle, rinse cycles, anti-crease

or delicate spin cycle

Heavily soiled fast colours (baby linen, etc.)

4

40°

60

Wash cycle, rinse cycles, anti-crease

or delicate spin cycle

Delicate colours (all types of slightly soiled

garments)

5

40°

60

Wash cycle, rinse cycles, anti-crease

or delicate spin cycle

Wool

6

40°

50

Wash cycle, rinse cycles, anti-crease

and delicate spin cycle

Very delicate fabrics (curtains, silk, viscose,

etc.)

7

30°

45

Wash cycle, rinse cycles, anti-crease

or draining cycle

Time for You

Heavily soiled whites and fast colours

8

60°

60

Wash cycle, rinse cycles,

intermediate and final spin cycles

Slightly soiled whites and delicate colours

(shirts, jumpers, etc.)

9

40°

50

Wash cycle, rinse cycles,

intermediate and final spin cycles

Delicate colours (all types of slightly soiled

garments)

10

40°

40

Wash cycle, rinse cycles, delicate

spin cycle

Delicate colours (all types of slightly soiled

garments)

11

30°

30

Wash cycle, rinse cycles and delicate

spin cycle

Sport

Sports shoes (MAX 2 pairs)

12

30°

50

Cold wash (without detergents),

wash cycle, rinse cycles and delicate

spin cycle

Fabrics for sportswear (Tracksuits, shorts, etc.)

13

30°

60

Wash cycle, rinse cycles,

intermediate and final spin cycles

PARTIAL PROGRAMMES

Rinse

Rinse cycles and spin cycle.

Spin cycle Draining and spin cycle

Drain Draining

7

GB

Setting the temperature

Turn the TEMPERATURE knob to set the wash

temperature (see Programme table on page 6).

The temperature can be lowered, or even set to cold

wash (

).

Setting the spin speed

Turn the SPIN SPEED knob to set the spin speed for

the programme selected.

The maximum spin speeds for each programme are as

follows:

Programmes Maximum spin speed

Cotton 1200 r.p.m.

Synthetics 800 r.p.m.

Wool 600 r.p.m.

Silk no

The spin speed can be lowered, or the spin cycle can

be excluded altogether by selecting the symbol

.

The washing machine will automatically prevent you

from selecting a spin speed higher than the maximum

speed for each programme.

Personalisations

Options

To enable an option:

1. press the button corresponding to the desired

option, according to the table below.

2. the option is enabled when the corresponding

button is illuminated.

Note: The rapid flashing of the button indicates that

the corresponding option cannot be selected for the

programme set.

WIXXL126-GB-indesit.p65 25/07/05, 16.277

Option Effect

Comments

Enabled with

programmes

Delay Timer

Delays the start of the

wash by up to 9

hours.

Press the button repeatedly until the LED corresponding

to the delay is turned off.

The fifth time the button is pressed, the option will be

disabled.

N.B. Once you have pressed the Start/Reset button, the

delay can only be decreased if you wish to modify it.

All

Mini Load

For washing a smaller

load.

In addition to reducing actual washing time, this option will

reduce water and energy consumption by up to 50%.

Note: You can reduce the amount of detergent you use

with this wash.

1, 2, 3, 4, 5

Rinse cycle

Easy Iron

This option reduces

the amount of

creasing on fabrics,

making them easier

to iron.

When this option is set, programmes 4, 5, 6, 7 and Rinse

cycle will end with the laundry left to soak (Anti-crease)

and the Rinse cycle phase LED will flash.

- to conclude the cycle, press the START/RESET button.

- to run the draining cycle alone, set the knob to the

relative symbol and press the START/RESET button.

3, 4, 5, 6, 7,

8, 9, 10,

Rinse cycle

Extra Rinse

Increases the

efficiency of the rinse.

Recommended when the appliance has a full load or with

large quantities of detergent.

1, 2, 3, 4, 5,

8, 9, 10, 12, 13

Rinse cycle

8

GB

Detergents and Laundry

Detergent dispenser

! Do not put any items into the drawer, other than

detergents designed to be released from the drawer,

as they may cause damage or blockage.

1. Pre-wash detergent

compartment.

Maximum 200 ml

powder or 100 ml liquid

2. Main wash detergent

compartment.

Maximum 400 ml

powder or 200 ml liquid

3. Fabric conditioner

compartment.

Maximum 120 ml.

Dispensing powder detergent

To achieve the best wash results the manufacturer’s

recommended amount of detergent should be

measured and added to the main detergent

compartment.

Dispensing liquid detergent

We recommend the use of a detergent dosing ball, as

provided by your detergent manufacturer.

Adding fabric conditioner

Pour the recommended amount of fabric conditioner

into the compartment. Do not exceed the maximum fill

line.

Pre-wash

(Programme 1)(Programme 1)

(Programme 1)

When selecting programme 1 add detergent to both

the pre-wash and the main wash compartment.

! Do not use in drum dosing devices with pre-wash

programme 1.

Maximum load size

• Divide your laundry according to:

- the type of fabric/the symbol on the label.

- the colours: separate coloured garments from

whites.

• Empty all pockets and check for loose buttons.

• Do not exceed the weight limits stated below, which

refer to the weight when dry:

Sturdy fabrics : max. 7kg

Synthetic fabrics : max. 3kg

Delicate fabrics : max. 2kg

Wool : max. 1kg

! DO NOT overload the machine as this could result in

reduced performance.

How much does your laundry weigh?

1 sheet 400-500g

1 pillow case 150-200g

1 tablecloth 400-500g

1 bathrobe 900-1200g

1 towel 150-250g

3

2

1

WIXXL126-GB-indesit.p65 25/07/05, 16.278

9

GB

Precautions and advice

! The machine was designed and built in compliance

with the applicable international safety regulations.

The following information is provided for your safety

and should consequently be read carefully.

General safety

• This appliance has been designed for non-

professional, household use and its functions must

not be changed.

• This machine should only be used by adults and in

accordance with the instructions provided in this

manual.

• Never touch the machine when barefoot or with wet

or damp hands or feet.

• Do not pull on the power supply cable to unplug the

appliance from the electricity socket. Pull the plug

out yourself.

• Do not open the detergent dispenser while the

appliance is in operation.

• Do not touch the drain water as it could reach very

high temperatures.

• Never force the machine door: this could damage

the safety lock mechanism designed to prevent

accidental openings.

• In the event of a malfunction, do not under any

circumstances touch internal parts in order to

attempt repairs.

• Always keep children well away from the appliance

while in operation.

• The appliance door tends to get quite hot during

the wash cycle.

• Should it have to be moved, proceed with the help

of two or three people and handle it with the utmost

care. Never try to do this alone, because the

appliance is very heavy.

• Before loading your laundry into the machine, make

sure the drum is empty.

Saving energy and respecting the

environment

Environmentally-friendly technology

If you only see a little water through your appliance

door, this is because thanks to the latest Indesit

technology, your machine only needs less than half the

amount of water to get the best results: an objective

reached to respect the environment.

Saving on detergent, water, energy and time

• To avoid wasting resources, the machine should be

used with a full load. A full load instead of two half

loads allows you to save up to 50% on energy.

• The pre-wash cycle is only necessary on extremely

soiled garments. Avoiding it will save on detergent,

time, water and between 5 and 15% energy.

• Treating stains with a stain remover or leaving them

to soak before washing will cut down the need to

wash them at high temperatures.

A programme at 60°C instead of 90°C or one at

40°C instead of 60°C will save up to 50% on

energy.

• Use the correct quantity of detergent, depending on

the water hardness, how soiled the garments are

and the amount of laundry you have, to avoid

wastage and to protect the environment: despite

being biodegradable, detergents do contain

ingredients that alter the natural balance of the

environment. In addition, avoid using fabric softener

as much as possible.

• If you use your machine between late in the

afternoon and the early hours of the morning, you

will help reduce the electricity board’s peak load.

• If your laundry has to be dried in a tumble dryer,

select a high spin speed. Having the least water

possible in your laundry will save you time and

energy in the drying process.

Disposal

• Disposing of the packaging material:

observe local regulations, so the packaging can be

re-used.

• Disposing of an old machine:

before scrapping your appliance, cut the power

supply cable and remove the appliance door.

Disposal of old electrical appliances

The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment (WEEE), requires

that old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected separately

in order to optimise the recovery and recycling of the

materials they contain and reduce the impact on

human health and the environment.

The crossed out "wheeled bin" symbol on

the product reminds you of your obligation,

that when you dispose of the appliance it

must be separately collected.

Consumers should contact their local

authority or retailer for information

concerning the correct disposal of their old

appliance.

WIXXL126-GB-indesit.p65 25/07/05, 16.279

10

GB

Switching off the electricity

• Turn off the water tap after every wash. This will

limit the wear of your appliance’s water system and

also prevent leaks.

• Unplug your appliance when cleaning it and during

all maintenance operations.

Cleaning

Cleaning the exterior

Use a damp cloth or silicon polish to clean the exterior

surfaces of the appliance.

Cleaning the door bowl

Clean the internal surface of the door bowl regularly

with a soft cloth. A build up of soap powder and water

hardness residue may result in water leaking from the

door.

Cleaning the dispenser drawer and

compartments

It is advisable to clean the dispenser drawer regularly.

! Do not try to clean any part of the dispenser drawer

while the machine is running.

1. Pull out the drawer until it

reaches its stop.

2. Press the drawer release

button to remove the dispenser

drawer (see figure).

3. Clean and dry the dispenser

drawer, syphons, grate and

fabric conditioner exit channel

(A). Also regularly clean the

outlet pipe area (B).

4. Relocate the dispenser drawer and push it firmly

back into place.

! Do not clean any part of the machine with abrasive

cleaners, scouring agents, acids, any bleach or metal

polish as they may cause damage.

Caring for your appliance door and

drum

• Always leave the appliance door ajar to prevent

unpleasant odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump which does not require regular maintenance.

However, it may be that small objects (coins, buttons,

etc.) fall into the pre-chamber that protects the pump

(the pump is located in the lower part of this pre-

chamber).

! Make sure that the wash cycle has finished and

remove the plug from the socket.

To access the pre-chamber:

1. remove the covering panel

on the front of the washing

machine using a screwdriver

(see figure).

2. unscrew the cover, turning it

in an anticlockwise direction

(see figure). a little water may

trickle out. This is perfectly

normal.

3. Clean the inside thoroughly.

4. Screw the cover back on.

5. Replace the cover panel, making sure that the

hooks are positioned in the right slots before pushing

the panel towards the machine.

Checking the water inlet hose

Check the water inlet hose at least once a year. If you

see any cracks, replace it immediately. During the

wash cycles, high water pressure could cause a

cracked hose to split open.

! Never use hoses that have already been used.

Care and Maintenance

B

A

WIXXL126-GB-indesit.p65 30/08/05, 9.5910

11

GB

Troubleshooting

Your washing machine could fail to work. Before calling for Assistance (see page 12), make sure the problem can’t

easily be solved by consulting the following list:

Possible causes / Solution:

• The appliance is not plugged into the socket, or not enough to make

contact.

• There has been a power failure.

• The appliance door is not shut properly.

• The

button has not been pressed.

• The START/RESET button has not been pressed.

• The water tap is not turned on.

• A delayed start has been set (using the Delay Timer. see page 7)

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap is not turned on.

• There is a water shortage.

• The water pressure is insufficient.

• The START/RESET button has not been pressed.

• The drain hose is not fitted between 65 and 100cm from the floor (see

page 3).

• The free end of the hose is underwater (see page 3).

• The wall drainage system doesn’t have a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and call for Assistance. If the dwelling is on one of the

upper floors of a building, there may be drain trap problems causing the

washing machine to load and unload water continuously. In order to avoid

such an inconvenience, special anti-drain trap valves are available in shops.

• The programme does not foresee the draining. Some programmes require

enabling the draining manually (see page 6).

• The Easy Iron option is enabled: to complete the programme, press the

START/RESET button (see page 7).

• The drain hose is bent (see page 3).

• The drain duct is clogged.

• The drum was not unblocked correctly during installation (see page 2).

• The washing machine is not level (see page 2).

• The washing machine is closed in between furniture cabinets and the wall

(see page 2).

• The water inlet hose is not screwed on correctly (see page 2).

• The detergent dispenser is obstructed, (to clean it see page 10).

• The drain hose is not secured properly (see page 3).

• Call for Assistance because this means there is an abnormality.

• The detergent is not suitable for machine washing (it should bear the

definition “for washing machines” or “hand and machine wash”, or the

like.)

• You used too much detergent.

Problem:

The washing machine won’t

start.

The wash cycle won’t start.

The washing machine fails to

load water.

The washing machine

continuously loads and unloads

water.

The washing machine does not

drain or spin.

The washing machine vibrates

too much during the spin cycle.

The washing machine leaks.

The ON-OFF/DOOR LOCK LED

flashes rapidly at the same time

as at least one other LED.

There is too much foam.

WIXXL126-GB-indesit.p65 25/07/05, 16.2711

12

GB

Service

Before calling for Assistance:

• Use the troubleshooting guide to see if you can

solve the problem yourself (see Troubleshooting).

• If not, turn off the appliance and call the Service

Centre closest to you.

What to tell the Service Centre:

• name, address and post code.

• telephone number.

• the type of problem.

• the date of purchase.

• the appliance model (Mod.).

• the serial number (S/N).

This information can be found on the data label inside

the door of the machine.

Spare Parts

This appliance is a complex machine. Repairing it

yourself or having a non-authorised person try to

repair it could cause harm to one or more persons,

could damage the machine and could invalidate the

spare parts warranty.

Call an authorised technician if you experience

problems while using the machine.

The spare parts have been designed exclusively for

this appliance and not for other uses.

WIXXL126-GB-indesit.p65 28/07/05, 11.1112

Page is loading ...

Whirlpool WIXXL126 Owner's manual

This manual is also suitable for

Whirlpool WIXXL126 Owner's manual

in other languages

Related papers

Other documents