Phoenix Gold TI600.4 User manual

Brand: Phoenix Gold

Model: TI600.4

Category: Car audio amplifiers

Type: User manual

This manual is also suitable for

Amplifier Manual

Manuel de l’amplificateur

Features

Models: Ti1500.1, Ti2500.1

Ti600.4, Ti800.4

• 24dBVariableLowPassandSubsonicCrossovers(Ti2500.1,Ti1500.1)

• 18dBVariableHighandLowPassCrossovers(Ti800.4,Ti600.4)

• Crossoversfeature41DetentsforExactFrequencySelection

• AudiophileBi-PolarOutputTransistors(Ti800.4,Ti600.4)

• HighEfciencyClassDTopology(Ti2500.1,Ti1500.1)

• MassiveUnregulatedPowerSuppliesfeaturingHandWoundTransformers

• PowerOutputPeakIndicators

• 1/0GaugeDirectInsertPowerTerminals

• LPL44-LowPassLevelControlReady

• RMD-RemoteMonitoringDisplayPort

• AdvancedThermalandProtectionCircuitry

phoenix gold ti amp manual.indd 1 3/2/10 11:20:39 AM

Amplier Owner’s Manual

MONOBLOCK SPECIFICATIONS

Frequency Response: ± 1dB from 20Hz to 300Hz

Signal to Noise Ratio: >90dB

Subsonic and Low Pass Crossovers: 24dB per octave

Low Pass Crossover Range: 30Hz to 300Hz

Subsonic Crossover Range: 10Hz to 55Hz

Bass Boost @ 45Hz: 0 to +18dB

Low Level Input Range: 200 millivolts to 8 volts

Lowest Recommend Load: 1 ohm

Typical Efciency: 80%

Damping Factor: Greater than 200

FOUR CHANNEL SPECIFICATIONS

Frequency Response: ± 1dB from 20Hz to 20kHz

Signal to Noise Ratio: >110dB

High and Low Pass Crossovers: 18dB per Octave

Low Pass Crossover Range: 40Hz to 400Hz

High Pass Crossover Range: 20Hz to 400Hz

Bass Boost @ 45Hz: 0 to +18dB

Low Level Input Range: 200 millivolts to 8 volts

Lowest Recommend Load: 4 ohm Bridged or 2 ohm Stereo

Typical Efciency: 50%

Damping Factor Greater than 200

Ti1500.1

Dynamic Power 14.4Vdc >1% THD 1100 x 1 @ 2 ohm

1500 x 1 @ 1 ohm

RMS Power 14.4Vdc ≤ 1% THD 900 x 1 @ 2 ohm

1250 x 1 @ 1 ohm

Recommended Fuse Size: 100A

Minimum Power/Ground Wire Size: 4 Gauge

Dimensions: 16.85” L x 9.8” W x 2.5” H

428mm x 252mm x 62mm

Ti2500.1

Dynamic Power 14.4Vdc >1% THD 1500 x 1 @ 2 ohm

2500 x 1 @ 1 ohm

RMS Power 14.4Vdc ≤ 1% THD 1100 x 1 @ 2 ohm

1650 x 1 @ 1 ohm

Recommended Fuse Size: 200A

Minimum Power/Ground Wire Size: 1/0 Gauge

Dimensions: 20.4” L x 9.8” W x 2.5” H

518mm x 252mm x 62mm

Ti600.4

Dynamic Power 14.4Vdc >1% THD 100 x 4 @ 4 ohm Stereo

150 x 4 @ 2 ohm Stereo

300 x 2 @ 4 ohm Bridged

RMS Power 14.4Vdc ≤1% THD 90 x 4 @ 4 ohm Stereo

120 x 4 @ 2 ohm Stereo

240 x 2 @ 4 ohm Bridged

Recommended Fuse Size: 80A

Minimum Power/Ground Wire Size: 4 Gauge

Dimensions: 16.85” L x 9.8” W x 2.5” H

428mm x 252mm x 62mm

Ti800.4

Dynamic Power 14.4Vdc >1% THD 125 x 4 @ 4 ohm Stereo

200 x 4 @ 2 ohm Stereo

400 x 2 @ 4 ohm Bridged

RMS Power 14.4Vdc ≤1% THD 115 x 4 @ 4 ohm Stereo

150 x 4 @ 2 ohm Stereo

300 x 2 @ 4 ohm Bridged

Recommended Fuse Size: 100A

Minimum Power/Ground Wire Size: 4 Gauge

Dimensions: 20.4” L x 9.8” W x 2.5” H

518mm x 252mm x 62mm

Specifications

phoenix gold ti amp manual.indd 2 3/2/10 11:20:39 AM

Amplier Owner’s Manual

INPUT

Connectpreampsignalcablesfromtheheadunittotheseterminals.

OUTPUT

Providesafullrangesignalforanadditionalamplier.Thereisnosignal

lossifusingthisoutput.

CROSSOVER FREQUENCY

Controlsthelowpasscrossoverpointforthespeakeroutputs.

BASS BOOST

Variablebassboostfrom0to+18dB@45Hz.

LOW PASS LEVEL CONTROL (LPL)

Thisportisforconnectingtheoptionalremotelevelcontrol(LPL44).This

allowsupto20dBofvolumeadjustment.Thisisnotabassboost,it

controlsthelevelofthelowpasssignal.

REMOTE MONITORING DISPLAY (RMD)

ConnectoptionalRMDVoltageDisplaytothisport

LEVEL

Usedtoreachmaximumamplierpowerwithawidevarietyofheadunits.

SUBSONIC CROSSOVER FREQUENCY

Controlsthehighpasscrossoverpointforthespeakeroutputstoeliminateextreme

lowfrequencies.

PEAK INDICATOR

Lightswhentheamplierreachesnearmaximumoutput.Undernormal

operationthepeakindicatorshouldbeashingduringthepeaksofthe

music.Peakindicatorshouldnotstaylitforlongperiodsoftime(more

than2or3seconds),ifthisisthecaseyouneedtoreducesystemvolume

orleveloftheamplier.

PROTECT INDICATOR

Lightsredifthereisaproblemwiththeaudiosystem.Forexample,speakerwireis

pinched/shortedtogetherortheamplierisrunningtoolowofanimpedance.

12V+

Thismustbeconnectedtothefusedpositiveterminal(+12V)ofthecar’s

battery.Thefusemustbelocatedwithin18inchesofthebattery.

REMOTE

Thismustbeconnectedtoswitched+12V,usuallyatriggerwirecoming

fromtheheadunitorignition.

GND

Thismustbeconnectedtothenegativeterminalofthecar’sbatteryor

boltedtoaclean,unpaintedpartofthechassisofthevehicle.

SPEAKER OUTPUTS

Usedtoconnecttheampliertospeakers.Minimumimpedanceis1ohm.

ti2500.1 - ti1500.1

Monoblock Power Amplifier

phoenix gold ti amp manual.indd 3 3/2/10 11:20:40 AM

Amplier Owner’s Manual

INPUT

Connectpreampsignalcablesfromtheheadunittotheseterminals.

CROSSOVER FREQUENCY

Controlsthecrossoverpointforthespeakeroutputs.

BASS BOOST

Variablebassboostfrom0to+18dB@45Hz.

2ch/4ch MODE

2ch:HeadunithasonepairofcablesintofrontInput.

4ch:Headunithastwopairsofcablesintofrontandrearinputs.

LOW PASS LEVEL CONTROL (LPL)

Thisportisforconnectingtheoptionalremotelevelcontrol(LPL44).Thisallows

upto20dBofvolumeadjustment.Thisisnotabassboost,itcontrolsthelevelof

theentirelowpasssignaloftherearchannels.

REMOTE MONITORING DISPLAY (RMD)

ConnectoptionalRMDVoltageDisplaytothisport

LEVEL

Usedtoreachmaximumamplierpowerwithawidevarietyofheadunits.

CONFIG

FLAT:Crossoversareturnedoff

HP:Highpasscrossoverison

LP/BP:LowandHighPasscrossoversareon,creatingaBandpass(BP)setting

formidbassdriversorsubwoofers.Forastandardsubwoofersystem,the

highpassfrequencynowbecomesasubsoniclter.Toturnsubsoniclter

off,turntheHPFREQ(SubsonicFilter)to20HzorFullCounterClockwise.

12V+

Thismustbeconnectedtothefusedpositiveterminal(+12V)ofthe

car’sbattery.Thefusemustbelocatedwithin18inchesofthebattery.

REMOTE

Thismustbeconnectedtoswitched+12V,usuallyatriggerwire

comingfromtheheadunitorignition.

GND

Thismustbeconnectedtothenegativeterminalofthecar’sbatteryor

boltedtoaclean,unpaintedpartofthechassisofthevehicle.

SPEAKER OUTPUTS

Usedtoconnecttheampliertospeakers.Usetheleft+andright-terminalsfor

bridgedmode.Minimumimpedanceis4ohmbridgedor2ohmstereo.

ti800.4 - ti600.4

4 Channel Power Amplifier

phoenix gold ti amp manual.indd 4 3/2/10 11:20:41 AM

Amplier Owner’s Manual

Allcrossoverfrequencypotentiometershave41detentsor“clicks”sotheendusercansettheexactcrossoverfrequencydesired.Nomoreturningthe

potentiometerandguessingwhereyourcrossoverpointsare.Yougetexactcontrolofyouramplier’soutput.

Crossover Settings

Ti2500.1 - Ti1500.1

clicks

Subsonic

(10~55hz)

(30~300Hz)

BassBoost

1 55 313 0.0

2 52 313 0.0

3 52 313 0.0

4 52 313 0.0

5 52 289 0.2

6 48 289 0.4

7 48 268 0.6

8 48 268 0.7

9 48 247 0.9

10 48 247 1.0

11 44 229 1.1

12 44 229 1.2

13 44 212 1.3

14 41 212 1.4

15 41 196 1.6

16 41 181 1.8

17 38 181 2.0

18 38 167 2.2

19 35 143 2.5

20 32 122 2.9

21 30 105 3.2

22 30 97 3.6

23 28 89 4.2

24 26 76 4.8

25 24 71 5.8

26 22 65 7.0

27 20 60 7.4

28 19 56 7.9

29 17 52 8.4

30 16 48 9.0

31 15 44 9.6

32 15 41 10.5

33 14 41 10.9

34 13 38 11.5

35 13 35 12.1

36 12 35 12.8

37 12 32 13.7

38 11 32 14.6

39 11 30 15.8

40 11 30 17.1

41 10 30 17.2

Ti800.4 - Ti600.4

clicks

(20~400hz)

(40~400Hz)

BassBoost

1 434 434 0.1

2 433 432 0.1

3 427 415 0.3

4 416 385 0.6

5 404 361 0.9

6 392 343 1.3

7 382 325 1.7

8 371 309 2.0

9 362 295 2.4

10 353 283 2.7

11 336 275 3.1

12 301 229 3.5

13 276 204 4.0

14 266 187 4.5

15 253 169 5.0

16 234 156 5.7

17 219 144 6.3

18 204 134 7.2

19 192 125 7.9

20 181 117 8.7

21 170 110 9.5

22 161 94 10.5

23 153 77 11.7

24 127 65 13.1

25 109 57 13.5

26 96 96 13.8

27 86 86 14.3

28 77 77 14.8

29 70 70 15.3

30 65 65 15.8

31 60 60 16.1

32 56 56 16.5

33 52 52 16.8

34 49 49 17.1

35 46 46 17.5

36 43 43 17.9

37 41 41 18.3

38 39 39 18.7

39 35 38 19.0

40 30 38 19.0

41 25 38 19.0

phoenix gold ti amp manual.indd 5 3/2/10 11:20:41 AM

Amplier Owner’s Manual

How to strap two monoblocks

Strapping or linking two Ti ampliers allows you to deliver a ton of power into a single voice coil commonly used in SPL competitions. The example below

shows two Ti1500.1s delivering a total of 3000 watts into a single 2 ohm voice coil. DO NOT STRAP AMPLIFIERS INTO A 1 OHM LOAD.

NOTES: The “Master” amplier’s preamp section controls both ampliers. “Slave” amplier’s pre-amp control are disabled.

Min Load is 2 ohm when strapped.

HEADUNIT

MASTER

SLAVE

SINGLE

CHANNEL

RCA

NOT USED

Speaker (- )is shorted

together using 12 gauge

speaker wire.

phoenix gold ti amp manual.indd 6 3/2/10 11:20:42 AM

Page is loading ...

Manuel de l’amplicateur

Réglages du filtre passif

Ti2500.1 - Ti1500.1

clicks

Subsonic

(10~55hz)

(30~300Hz)

BassBoost

1 55 313 0.0

2 52 313 0.0

3 52 313 0.0

4 52 313 0.0

5 52 289 0.2

6 48 289 0.4

7 48 268 0.6

8 48 268 0.7

9 48 247 0.9

10 48 247 1.0

11 44 229 1.1

12 44 229 1.2

13 44 212 1.3

14 41 212 1.4

15 41 196 1.6

16 41 181 1.8

17 38 181 2.0

18 38 167 2.2

19 35 143 2.5

20 32 122 2.9

21 30 105 3.2

22 30 97 3.6

23 28 89 4.2

24 26 76 4.8

25 24 71 5.8

26 22 65 7.0

27 20 60 7.4

28 19 56 7.9

29 17 52 8.4

30 16 48 9.0

31 15 44 9.6

32 15 41 10.5

33 14 41 10.9

34 13 38 11.5

35 13 35 12.1

36 12 35 12.8

37 12 32 13.7

38 11 32 14.6

39 11 30 15.8

40 11 30 17.1

41 10 30 17.2

Ti800.4 - Ti600.4

clicks

(20~400hz)

(40~400Hz)

BassBoost

1 434 434 0.1

2 433 432 0.1

3 427 415 0.3

4 416 385 0.6

5 404 361 0.9

6 392 343 1.3

7 382 325 1.7

8 371 309 2.0

9 362 295 2.4

10 353 283 2.7

11 336 275 3.1

12 301 229 3.5

13 276 204 4.0

14 266 187 4.5

15 253 169 5.0

16 234 156 5.7

17 219 144 6.3

18 204 134 7.2

19 192 125 7.9

20 181 117 8.7

21 170 110 9.5

22 161 94 10.5

23 153 77 11.7

24 127 65 13.1

25 109 57 13.5

26 96 96 13.8

27 86 86 14.3

28 77 77 14.8

29 70 70 15.3

30 65 65 15.8

31 60 60 16.1

32 56 56 16.5

33 52 52 16.8

34 49 49 17.1

35 46 46 17.5

36 43 43 17.9

37 41 41 18.3

38 39 39 18.7

39 35 38 19.0

40 30 38 19.0

41 25 38 19.0

phoenix gold ti amp manual.indd 10 3/2/10 11:20:45 AM

Manuel de l’amplicateur

Comment sangle deux monoblocs

AUTORADIO

MASTER

SLAVE

CABLE RCA

PRINCIPAL

PAS UTILIZE

Relier ensemble

les bornes haut-parleur

négatives (-) des

amplificateurs.

phoenix gold ti amp manual.indd 11 3/2/10 11:20:46 AM

Phoenix Gold

A Division of AAMP of America™

13190 56th Court

Clearwater, Florida 33760

P: 888-228-5560

[email protected]

www.phoenixgold.com

Designed and Engineered in the USA

PhoenixGoldProductWarranty

LIMITEDWARRANTYONAMPLIFIERS

PhoenixGoldwarrantsthisproducttobefreeofdefectsinmaterialsandworkmanshipforaperiodofone(1)yearsfromtheoriginaldateofpurchase.This

warrantyisnottransferableandappliesonlytotheoriginalpurchaserfromanauthorizedPhoenixGolddealerintheUnitedStatesofAmericaonly.Should

servicebenecessaryunderthiswarrantyforanyreasonduetomanufacturingdefectormalfunction,PhoenixGoldwill(atitsdiscretion),repairorreplace

thedefectiveproductwithneworremanufacturedproductatnocharge.Damagecausedbythefollowingisnotcoveredunderwarranty:accident,misuse,

abuse,productmodicationorneglect,failuretofollowinstallationinstructions,unauthorizedrepairattempts,misrepresentationsbytheseller.Thiswarranty

doesnotcoverincidentalorconsequentialdamagesanddoesnotcoverthecostofremovingorreinstallingtheunit(s).Cosmeticdamageduetoaccidentor

normalwearandtearisnotcoveredunderwarranty.

INTERNATIONALWARRANTIES:

ProductspurchasedoutsidetheUnitedStatesofAmericaarecoveredonlybythatcountry’sAuthorizedPhoenixGoldresellerandnotbyPhoenixGold.

Consumersneedingserviceorwarrantyinformationfortheseproductsmustcontactthatcountry’sresellerforinformation.

phoenix gold ti amp manual.indd 12 3/2/10 11:20:46 AM