American Standard 2425.018W User manual

American Standard
Brand
American Standard
Model
2425.018W
Category
Sanitary ware
Type
User manual

This manual is also suitable for

American Standard 2425.018W is a high gloss acrylic drop-in whirlpool with a nominal dimension of 60" x 32" x 21-1/2". It comes with a pre-leveled tub bottom, form-fitted backrest, and dual, molded-in armrests. The whirlpool features an eight multi-directional and flow-adjustable jets including two Ideal-flow jets, four body massage jets, and two recessed back-rest jets. It also has a deck-mounted air switch On/Off and two silent air volume controls. The whirlpool system is factory installed and tested, and it features a Quick Connect Safe-T-Heater connection system.

American Standard 2425.018W is a high gloss acrylic drop-in whirlpool with a nominal dimension of 60" x 32" x 21-1/2". It comes with a pre-leveled tub bottom, form-fitted backrest, and dual, molded-in armrests. The whirlpool features an eight multi-directional and flow-adjustable jets including two Ideal-flow jets, four body massage jets, and two recessed back-rest jets. It also has a deck-mounted air switch On/Off and two silent air volume controls. The whirlpool system is factory installed and tested, and it features a Quick Connect Safe-T-Heater connection system.

HAMPTON™ 5’ DROP-IN
WHIRLPOOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
BV-20
3/03
To Be Specified - Required:
❏ Color:
❏ Bath Faucet: (specify finish)
❏ Bath Drain: 1583.470 (specify finish)
To Be Specified - Optional:
❏ Safe-T-Heater*: 9075.120
❏ Bath Caddie: 9533.100 (in Chrome only)
❏ Jet Trim Ring Kit: 9860.200-two per kit (specify finish)
For color/finish availability and other faucet choices,
please see the Product Selector and Pricing Guide.
* NOTE: the Safe-T-Heater is designed to maintain water
temperature during operation. It will not heat cold water to
desired bathing temperature.
HAMPTON™ 5’ DROP-IN WHIRLPOOL
❏ 2425.018W Whirlpool featuring System I
• Acrylic with fiberglass reinforcement
• Pre-leveled tub bottom
• Form-fitted backrest
• Dual, molded-in arm rests
• 1.5 HP single speed, self-draining pump/motor
• Factory-installed power cord with plug
• Eight multi-directional and flow-adjustable jets
including:
- Two Ideal-flow jets
- Four body massage jets
- Two recessed back-rest jets
• Deck-mounted air switch On/Off
• Two silent air volume controls
• Quick Connect Safe-T-Heater connection
system
• Factory installed and tested whirlpool system
Whirlpool Massage featuring System I
❏ 2425.018WC StayClean™ Whirlpool Massage
featuring System I:
• Same as above except with the StayClean™
whirlpool system featuring Antimicrobial
AlphaSan®
Nominal Dimensions:
60” x 32” x 21-1/2” (1524 x 813 x 546mm)
Compliance Certifications -
Meets or Exceeds the Following Specifications:
• Underwriters Laboratories - Hydromassage
Bathtubs UL 1795
• ASME A112.19.7M for Whirlpool Appliances
• ANSI Z124.1 for Plastic Bathtubs
• ASTM E162 for Flammability
• NFPA 258 for Smoke Density
NOTE: Roughing-in dimensions and product
specifications shown on reverse side of page.
HAMPTON™ 5’ DROP-IN
WHIRLPOOL
HIGH GLOSS ACRYLIC
© 2003 American Standard Inc.
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE
INSTALLATION. SUPPORT OF BATH BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. SUPPORT AND
ENCLOSING MATERIAL BY OTHERS.
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
OPTIONAL 3 WALL TILING BEAD. KIT No. TILE-BEAD AND APRON No. WBURG5-APRON AVAILABLE AND MUST BE
ORDERED SEPARATELY.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT:
Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1
These measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or
voided leaflet.
■
19-1/2
(495mm)
21-1/2
(546mm)
1-1/2 O.D.TAILPIECE
INTEGRAL
FEET
■ LEVELING
STRINGER
NOT FOR
SUPPORT
ROUGH
FLOOR
FINISHED
WALL
60
(1524mm)
32
(813mm)
16
(406mm)
10-1/4
(260mm)
12
(305mm)
3
(76mm)
(8) JETS
3-1/2
(89mm)
2
(51mm)
CUTOUT IN FLOOR FOR DRAIN
PUMP
FINISHED
WALL
12
(305mm) OPT.
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
65 & 78
(1651 & 1981mm)
C/L OF
OVERFLOW
4
(102mm)
C/L OF
SPOUT
C/L OF
VALVES
C/L OF
SHOWER ARM
2-3/4
(70mm)
4-5/8
(117mm)
1-1/2 N.P.T.M.
THREADS
3/4
(19mm)
9
(229 mm)
C/L OF
SUPPLIES
C/L OF DRAIN
SEE FITTING
SPECS FOR
DIMENSIONS
(2) AIR VALVES
ON/OFF
SWITCH
PROVIDE ACCESS
TO PUMP FOR
SERVICE ON ALL
INSTALLATIONS
UNDERSIDE
OF DECK
SAFE-T-HEATER
REMOVABLE
BLANK
OUTLINE OF CUTOUT
58-1/2 X 30-1/2
(1486 X 775mm)
GENERAL SPECIFICATIONS FOR 2425 WHIRLPOOL
WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP 1.6 HP, 9.7 AMPS,120V.
60 x 32 x 21-1/2 (1524 x 813 x 546mm)
115 Lbs. (52 Kg.)
574 Lbs. (258 Kg.)
55 Gal. (208 L.)
45 Gal. (171 L.)
16-1/4 x 38-1/4 (413 x 972mm)
26-1/4 x 52-1/2 (667 x 1334mm)
15 (381mm)
43 Lbs./Sq.Ft. (208 Kgs./Sq.m)
15.6
35.3
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
3
)
  • Page 1 1
  • Page 2 2

American Standard 2425.018W User manual

American Standard
Brand
American Standard
Model
2425.018W
Category
Sanitary ware
Type
User manual
This manual is also suitable for

American Standard 2425.018W is a high gloss acrylic drop-in whirlpool with a nominal dimension of 60" x 32" x 21-1/2". It comes with a pre-leveled tub bottom, form-fitted backrest, and dual, molded-in armrests. The whirlpool features an eight multi-directional and flow-adjustable jets including two Ideal-flow jets, four body massage jets, and two recessed back-rest jets. It also has a deck-mounted air switch On/Off and two silent air volume controls. The whirlpool system is factory installed and tested, and it features a Quick Connect Safe-T-Heater connection system.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers