Liebherr 7080 359-02 User manual

www.liebherr.com

For Service in the U.S.:

Liebherr Service Center

15545 N. 77th Street

Scottsdale, AZ 85260

Phone: (480) 998-0141

Fax: (480) 998-7877

Toll Free:

1-866-LIEBHERR

1-866-543-2437

E-mail: Liebherr@adcoservice.com

For Service in Canada:

EURO-LINE APPLIANCES

2150 Winston Park Drive - Unit 20

Oakville, Ontario, L6H 5V1

Phone: (905) 829-3980

Fax: (905) 829-3985

Toll Free:

1-800-678-8352

Part No. 7080 359-02

7080-359-02_C16_CI16_CS16Instal_3Lang.qxd 9/7/2004 8:58 AM Page 18

Installation

Instructions

For Built-In NoFrost Combined

Refrigerator-Freezers

Instructions

de montage

Pour le combiné réfrigérateur-

congélateur NoFrost encastrable

Instrucciones

de instalación

Para conbinados frigorífico-

congelador NoFrost empotrables

C 16

CI 16

7080 359-02

7080-359-02_C16_CI16_CS16Instal_3Lang.qxd 9/7/2004 8:58 AM Page i

IMPORTANT

C 16/CI 16

A delight in freshness

PLEASE READ AND FOLLOW

THESE INSTRUCTIONS

These instructions contain Warning and Caution

statements.This information is important for safe

and efficient installation.

Always read and follow all Warning and Caution

statements!

States a hazard that may cause serious

injury or death if precautions are not

followed.

Signals a situation where minor injury of

product damage may occur if you do not

follow instructions.

IMPORTANT

This highlights information that is especially

relevant to a problem-free installation.

Make sure incoming voltage is the same as the unit

rating.

To reduce the risk of fire, electric shock, or personal

injury, installation work and electrical wiring must be

done by a qualified electrician in accordance with

all applicable codes and standards, including fire-

rated construction.

TO THE INSTALLER

It is very important that the guidelines and

instructions are followed in the manual to ensure

proper installation and operation of the unit.The

Installation Guidelines section contains important

information for making sure the installation is

correct. Read and understand all the information in

Installation Guidelines, and in this manual before

the unit is installed.

CAUTION

!

WARNING

7080-359-02_C16_CI16_CS16Instal_3Lang.qxd 9/7/2004 8:58 AM Page ii

7080-359-02_C16_CI16_CS16Instal_3Lang.qxd 9/7/2004 8:58 AM Page 1

A delight in freshness

Table of Contents

1

C 16/CI 16

Contents Page

Features ....................................................................................................... 2

Installation Guidelines

Area Requirements................................................................................ 3

Electrical Requirement........................................................................... 3

Customer’s Responsibility...................................................................... 3

Blocking For Safety................................................................................ 3

Unit Venting............................................................................................ 3

Reversing the Door Hinges ................................................................... 3

Planning Information

Cabinet Opening Dimensions.................................................................4

Integrating Cabinetry

Framed Panels....................................................................................... 6

Overlay Panels....................................................................................... 7

Mounting the Upper Ventilation Grille........................................................ 10

Leveling the Refrigerator............................................................................ 11

Blocking for Safety ..................................................................................... 12

Door Stop Adjustment................................................................................ 13

Reversing Door Hinges.............................................................................. 14

Liebherr Warranty Plan.............................................................................. 17

FEATURES

2

C 16/CI 16

Figure 1

Operating and

control elements

Butter and cheese

compartment

Adjustable door racks

Adjustable shelves

Vegetable bin

Drawers

Freezing chart

Adjustable-height unit

Gallon shelf

Beverage Rack

A delight in freshness

INSTALLATION GUIDELINES

3

C 16/CI 16

Area Requirements

Verify the following:

• Floors can support refrigerator’s weight plus

approximately 1200 pounds (544 kg) of food

weight.

• Finish kitchen floor height is level. Refrigerator

must be shimmed to the floor level if the floor

heights are not equal to make sure air vents are

not obstructed.

• Remove anything attached to rear or side walls

that can obstruct refrigerator opening.

• Cutout dimensions are accurate.

• Electrical outlet is in correct location.

Do not install this unit next to another refrigerator or

freezer.This is important to prevent condensation

or consequential damage from another unit.

Electrical Requirement

If codes require a separate grounding circuit to be

used, have a qualified electrician install the circuit.

Do not ground to a gas pipe. Check with a

qualified electrician if you are not sure the

appliance is properly grounded. Do not

have a fuse in the neutral or grounding

circuit.

ELECTRICAL SHOCK HAZARD

• Electrically ground refrigerator.

• Do not use an extension cord.

• Failure to follow these instructions

could result in fire or electrical shock.

!

WARNING

!

WARNING

ELECTROCUTION HAZARD

Electrical Grounding Required.This

appliance is equipped with a three-prong

(grounding) polarized plug for your

protection against possible shock hazards.

•

DO NOT remove the round grounding

prong from the plug.

•

DO NOT use a two-prong grounding

adapter.

•

DO NOT use an extension cord to

connect power to the unit.

Customer’s Responsibility

A 115 Volt, 60 Hz, 15 Amp (20 Amp for side-by-side

installation) fused electrical supply is required.We

recommend using a dedicated circuit for this

appliance to prevent electrical overload. Follow the

National Electrical Code and local codes and

ordinances when installing the receptacle.

Blocking For Safety

The anti-tip brackets must be installed to prevent

the unit from tipping after it is installed. Refer to

Blocking For Safety.

Unit Venting

DO NOT restrict the air flow. Air flow must be

provided for the unit to operate.The factory air

vents provide 31 square inches (200 cm

2

) of air

flow. If you are replacing the factory air vents with

an overlay, the air flow must be the same or greater

than the factory air vents.

Reversing the Door Hinges

If the hinges and door handles are reversed, you

must obtain the Reverse Set.The Reverse Set is

not included with the unit. Contact your Liebherr

retailer, only for CI 16 unit.The door handles must

be installed before the screw covers are installed. If

you fail to install the handles before the screw

covers, you can damage the covers.The screw

covers are taped to the unit door during shipping.

Use care when removing the covers.

!

WARNING

A delight in freshness

PLANNING INFORMATION

4

C 16/CI 16

A delight in freshness

Cabinet Opening Dimensions

Figure 2

7" (17.8 cm)

6" (15.2 cm)

29-1/2" (75 cm)

83-3/4" (212.7 cm)

24" (61 cm)

75-1/2" (192 cm)

3" (7.6 cm)

18" (45.7 cm)

LOCATE WATER SUPPLY

WITHIN BOTTOM

SHADED AREA

ELECTRICAL OUTLET

LOCATION

Allow units to open a minimum of 90° to prevent

problems removing drawers.With the door opening

90°, you may have to move drawers slightly to clear

the door interior.

Refer to the minimum door clearances in the Pre-

Installation Specifications chart.

• Allow for a minimum 2" (5.08 cm) filler, for corner

installations, so the door can open to 90°. If

you’re using raised panels, consider using a

wider filler.

• Use a filler strip when units are installed side by

side.The width of this filler strip will vary

depending on the configuration and panels used.

• Be sure to add the filler strip width to the finished

rough-in dimension. In any side by side

installation, add an additional 1/2" (1.27 cm) to

the combined numbers.

IMPORTANT

Refer to the scaled illustrations at the end of

this section for specifics on door openings

and filler size alternatives.

PLANNING INFORMATION

5

C 16/CI 16

A delight in freshness

Figure 3

30" (76.2 cm)

83.9" (213 cm)*

24-1/2" (62 cm) - CI 16

24" (60,9 cm) - C 16

26" (66 cm)

81" (206 cm)*

90˚

130˚

29" (73.7 cm)

22.9" (58.2 cm)

30" (76.2 cm)

52.7" (134 cm)

47" (449.5 cm)

1.8" (4.6 cm)

19" (48.2 cm)

DOOR SWING CLEARANCE

Air Vent

* Overall height can be

increased 5/8" (1.59 cm)

by turning the adjustable

roller base.

INTEGRATING CABINETRY - CI 16 ONLY

6

C 16/CI 16

A delight in freshness

Framed Panels

If the thickness of the custom panels is less than

1/4" (0.635 cm), they must be backed up with a

sheet of shim material to build the total thickness to

1/4" (0.635 cm). If the panel is thicker than 1/4"

(0.635 cm), an edge must be routed around the

panel to ensure a proper fit.

Panels 1/4" (0.635 cm) thick or less

Trim reveal

1/4" min.

1/4" Panel

Panels thicker than 1/4" (0.635 cm)

Rout to 1/4"

thickness

Trim reveal

1/4" min.

FRAMED PANEL SPECIFICATION

28.9" (73.5 cm) 46.3" (117.6 cm)

28.4" (72.1 cm)

Refrigerator

Panel

Freezer

Panel

Figure 4

IMPORTANT

If you are replacing the factory air vents with

an overlay, DO NOT restrict the air flow.The

air flow must be the same or greater than the

factory air vents of 31 square inches (200

cm

2

).

The door handles must be installed before the

screw covers are installed. If you fail to install

the handles before the screw covers, you can

damage the covers.The screw covers are

taped to the unit doors during shipping. Use

care when removing covers.

The door panel weight must not exceed 25 lb

(11.3 kg).

INTEGRATING CABINETRY - CI 16 ONLY

7

C 16/CI 16

A delight in freshness

Overlay Panels

The overlay design line allows decorative panels to

cover the door trim for a more seamless

appearance that blends with the design of the

room.To achieve this look, the most common way

is to work with three panels, the decorative overlay

panel, a 0.10" (0.25 cm) spacer panel and a 1/4"

(0.635 cm) backer panel.

Overlay Panel 28.7" (72.9 cm)

Spacer Panel 27.4" (69.6 cm)

Backer Panel 28.2" (71.7 cm)

Overlay Panel 47.6" (120.9 cm)

Spacer Panel 45.3" (115 cm)

Backer Panel 46.3" (117.6 cm)

Overlay Panel 29.2" (74.3 cm)

Spacer Panel 27.9" (70.9 cm)

Backer Panel 28.9" (73.5 cm)

Refrigerator

Panel

Freezer

Panel

0.1" (0.25 cm)

0.0625" (0.16 cm)

0.6" (1.5 cm)

Overlay Panel

Spacer Panel

1/4" (0.635 cm)

Backer Panel

7080 010

Figure 5

Depending on your cabinet manufacturer, this could

be one panel routed for different dimensions or,

more likely, three different panels.

IMPORTANT

If you are replacing the factory air vents with

an overlay, DO NOT restrict the air flow.The

air flow must be the same or greater than the

factory air vents of 31 square inches (200

cm

2

).

The door handles must be installed before the

screw covers are installed. If you fail to install

the handles before the screw covers, you can

damage the covers.The screw covers are

taped to the unit doors during shipping. Use

care when removing covers.

The door panel weight must not exceed 25 lb

(11.3 kg).

INTEGRATING CABINETRY - CI 16 ONLY

8

C 16/CI 16

Figure 6

A = 1/4" (0.6 cm)

B = 1/2" (1.3 cm)

C = 3/4" (1.9 cm)

D = 1" (2.5 cm)

E = 1-1/4" (3.2 cm)

F = 1-1/2" (3.8 cm)

G = 1-3/4" (4.4 cm)

H = 2" (5.1 cm)

I = 2-1/4" (5.7 cm)

J = 2-1/2" (6.4 cm)

K = 2-3/4" (7.0 cm)

L = 3" (7.6 cm)

A delight in freshness

9

C 16/CI 16

A delight in freshness

INTEGRATING CABINETRY - CI 16 ONLY

The factory setting for the door to swing open is

130°. Use this illustration to ensure other cabinets

or counters do not interfere with the door opening.

Frameless cabinets:The casing trim overlaps the

cabinets at the side and top. Cabinets may require

filler strips to prevent interference with the cabinet

door swing.The door opening must allow for filler

strips.

A

B

C

D

E

F

G

H

I

J

K

L

M

L

K

J

I

H

G

H

I

J

K

L

A = 3" (7.6 cm)

B = 2-3/4" (7 cm)

C = 2-1/2" (6.4 cm)

D = 2-1/4" (5.8 cm)

E = 2" (5.1 cm)

F = 1-3/4" (4.5 cm)

G = 1-1/2" (3.8 cm)

H = 1-1/4" (3.2 cm)

I = 1" (2.5 cm)

J = 3/4" (1.9 cm)

K = 1/2" (1.3 cm)

L = 1/4" (0.6 cm)

M = 0"

23-5/8" (60 cm)

to rear of Liebherr

Nominal Overall

Width of Liebherr

Door closed

Overlay Panel

(

3/4" Nominal Size)

Door Open @ 130˚

Figure 7 - CI 16 only

INTEGRATING CABINETRY - CI 16 ONLY

10

C 16/CI 16

Figure 8

Nominal Overall

Width of Liebherr

Door Closed

Door Open 130˚

A

B

C

D

E

F

G

H

I

J

K

L

B

C

D

E

F

0˚

A = 1/4" (0.6 cm)

B = 1/2" (1.3 cm)

C = 3/4" (1.9 cm)

D = 1" (2.5 cm)

E = 1-1/4" (3.2 cm)

F = 1-1/2" (3.8 cm)

G = 1-3/4" (4.4 cm)

H = 2" (5.1 cm)

I = 2-1/4" (5.7 cm)

J = 2-1/2" (6.4 cm)

K = 2-3/4" (7.0 cm)

L = 3" (7.6 cm)

A delight in freshness

11

C 16/CI 16

A delight in freshness

INTEGRATING CABINETRY - CI 16 ONLY

The optional setting for the door to swing open is

90°. Use this illustration to ensure other cabinets or

counters do not interfere with the door opening.

Frameless cabinets:The casing trim overlaps the

cabinets at the side and top. Cabinets may require

filler strips to prevent interference with the cabinet

door swing.The door opening must allow for filler

strips.

23-5/8" (60 cm)

to rear of Liebherr

Main Frame

Nominal Overall

Width of Liebherr

Door closed

Door Open 90˚

Overlay Panel

(3/4" Nominal Size)

A

B

C

D

E

F

G

F

E

D

C

B

A = 0" (0 cm)

B = 1/4" (0.6 cm)

C = 1/2" (1.3 cm)

D = 3/4" (1.9 cm)

E = 1" (2.5 cm)

F = 1-1/4" (3.2 cm)

G = 1-1/2" (3.8 cm)

Figure 9 - CI 16 only

INTEGRATING CABINETRY - CI 16 ONLY

12

C 16/CI 16

Figure 10

Nominal Overall

Width of Liebherr

Door Closed

Door Open 90˚

A

B

C

D

E

F

G

H

I

J

K

L

B

C

D

E

F

0˚

A = 1/4" (0.6 cm)

B = 1/2" (1.3 cm)

C = 3/4" (1.9 cm)

D = 1" (2.5 cm)

E = 1-1/4" (3.2 cm)

F = 1-1/2" (3.8 cm)

G = 1-3/4" (4.4 cm)

H = 2" (5.1 cm)

I = 2-1/4" (5.7 cm)

J = 2-1/2" (6.4 cm)

K = 2-3/4" (7.0 cm)

L = 3" (7.6 cm)

A delight in freshness

13

C 16/CI 16

A delight in freshness

MOUNTING THE UPPER

VENTILATION

GRILLE

Figure 11

Screws

Grille

Installation Frame

Position the ventilation grille at the top of the

installation frame and attach it later with

countersunk screws (4 pieces, provided). Make

sure the grille fits flush laterally with the installation

frame.

IMPORTANT

If you are replacing the factory air vents with

an overlay, DO NOT restrict the air flow.The

air flow must be the same or greater than

the factory air vents of 31 square inches

(200 cm

2

).

14

C 16/CI 16

A delight in freshness

LEVELING THE REFRIGERATOR

1. Loosen the lower ventilation grille screws

(Fig. 12, 1).

The height can be adjusted in front by twisting

the leveling wheels (Fig. 12, 2).

2. Twist the adjusting bolt (Fig. 12, 3) to set up the

back of the refrigerator.

3. Rotate leveling until firmly in place against the

floor.

4. Align refrigerator with sides of kitchen cabinets

by adjusting leveling wheels and the supports.

5. Install the ventilation grille.

Figure 12

2

1

3

2

3

15

C 16/CI 16

A delight in freshness

BLOCKING FOR SAFETY

1. Secure the refrigerator in place so it does not tip

forward when the fully stocked door is opened.

2. Measure the distance from the floor to the upper

edge of the unit.

3. Locate and mark two wall studs against the wall

where the refrigerator will be located.The space

between the unit top and the bottom of the

brackets must not be more than 1/4" (0.635 cm).

4. Make sure the screws extend a minimum of 1"

(2.54 cm) into each of the wall studs.

5. Make sure the anti-tip brackets extend at least 3"

(7.62 cm) over the unit and are securely in place.

IMPORTANT

The anti-tip brackets can be installed in either

direction or closer together. Always position

the anti-tip brackets as wide apart as

possible, but make sure they are anchored to

two studs.

6. Using the front and rear levelers, raise the unit

until it makes contact with the brackets. Make

sure the front levelers are firmly on the floor to

prevent appliance from tipping forward.

IMPORTANT

If your unit is positioned in between the wall

studs, a board can be secured to the wall.

Make sure the board is secured to the studs

with screws that will penetrate into the studs a

minimum 1" (2.54 cm).The board should be a

minimum of 1" x 6" (2.54 cm x 15.24 cm) and

long enough to secure both ends to the wall

studs.

Figure 13

Wall Stud

Screws

Bracket

min 3"

16

C 16/CI 16

A delight in freshness

DOOR STOP ADJUSTMENT

Figure 15

1

2

Select between two opening angles: 130° and 90°.

Your appliance was delivered with a door opening

of 130°. If 90° opening angle is required, use this

procedure:

1. Close the refrigerator door.

2. Turn screw (1), provided, into bore (2).

Use the same procedure to set up the freezer door.

Figure 14

1

2

NOTES

17

C 16/CI 16

A delight in freshness

18

C 16/CI 16

A delight in freshness

REVERSING DOOR HINGES - CI 16

13. Mount the right installation frame (10) on the

other side. Discard the two other frames (11).

14. Mount the two enclosed frames (12) on the

right side. Do not forget the angle bracket

corner (13).

15. Lock the angle bracket (13) with the installation

frame.

16. Remove the door mounting from the refrigerator

and attach it on the other side (14).

17. Remove hinge sockets (15).

18. Remove door change frames (16).

19. Pull out shrouded-type panel (17) at the door

change frame at the handle side.

20. Remove screws (19).

21. Remove handle (18).

22. Remove the other door change frames (20) and

mount them on the opposite side.

23. Insert handle brackets (21) again into the slots

and attach handle.

24. Push shrouded-type panel (22) in the door

change frames.

25. Mount door change frames above and down

(23).

26. Insert hinge socket (24) into the frames.

27. Attach hinge socket (25) with screws to the

door.

28. Follow these instructions to change the other

door.

29. Insert spacers (26) for the upper door.

30. Attach center door fixture (27).

31. Place down lower door again on the lower door

mounting bracket.

32. Insert the metal pin (28) into the sleeve.

33. Position other door on the door mounting

center. Use other spacer (29) and attach door

with hinge bolt (30).

34. Mount the upper ventilation grille (Figure 11).

IMPORTANT

If the hinges and door handles are reversed,

you must obtain the Reverse Set.The

Reverse Set is not included with the unit.

Changing the door stop must be made by

two people to prevent personal injury and

damage to the doors.

1. Remove the upper ventilation grille if already

installed.

2. Remove the screw (1) at the door fixture.

Secure door to prevent personal injury

and to prevent the door from falling down.

3. Remove spacers (2).

The door can now be lifted and placed on the

floor.

4. Pull out the bearing pin (3) at the door fixture

center.

Secure door to prevent personal injury

and to prevent the door from falling down.

5. Lift the door and place it on the floor.

6. Remove the door fixture (4).

7. Loosen the screws at the door fixture.

8. Remove the screw (5) at the lower door fixture

and turn it into the other bore.

The door fixture down can be mounted again

on the other side (6).

9. Pull out plastic sleeve and assemble on the

opposite side of the bracket (7).

10. Remove both screws (8) at the back of the

installation frame.

11. Remove the 18 mounting screws (9) to

dismantle the installation frame.

12. Mount the installation frame.

CAUTION

!

CAUTION

!

CAUTION

!

Page is loading ...

Liebherr 7080 359-02 User manual

This manual is also suitable for

Liebherr 7080 359-02 User manual

in other languages

Related papers

Other documents