D-Link DCS-825L Quick Install Manual

Brand: D-Link

Model: DCS-825L

Category: Baby video monitors

Type: Quick Install Manual

D-Link DCS-825L is a Wi-Fi baby camera with a range of features to help you keep an eye on your little one. With its high-definition camera and night vision, you can see your baby clearly even in the dark. The camera also has a temperature sensor so you can make sure your baby's room is at a comfortable temperature.

The D-Link DCS-825L also has a built-in microphone and speaker so you can talk to your baby or sing them a lullaby. You can also use the mydlink Baby app to control the camera remotely, so you can check in on your baby from anywhere.

Here are some of the features of the D-Link DCS-825L:

DCS-825L

Quick Install Guide

Wi-Fi Baby Camera

Day & Night HD Cloud Camera

Before you Begin

D-Link and the D-Link logo are trademarks or registered trademarks of D-Link Corporation or

its subsidiaries in the United States or other countries. All other company or product names

mentioned herein are trademarks or registered trademarks of their respective companies.

expressed written permission from D-Link Systems, Inc.

• Please save this guide for future reference.

• Read these instructions before using your product.

• Do not cover the ventilation holes.

• Do not cover this product with a blanket.

• Do not allow children to play with this product.

• Do not allow this product to get wet. Only use a dry cloth to clean it.

• Cleaning: You only need to clean the desktop base when the sticky pad is

no longer sticky. When the pad is dirty, it easily detaches from the camera.

The pad may be cleaned with water and air-dried. (Don’t use a cloth to dry it.)

Make sure the base is completely dry before attaching it to the camera again.

• Do not place this product near water or other liquids, such as near a sink,

shower, or bathtub.

• Do not attempt to open or disassemble this product.

• Strangulation Hazard: Keep this product and any attached cords at least 3

feet out of reach of a child. Keep any attached cords out of your baby’s crib/

cot.

• This product is not a replacement for responsible adult supervision.

If any of the above items are missing, please contact your reseller.

DCS-825L Wi-Fi Baby Camera

Power Adapter

Desktop Base

Quick Install Guide

Package Contents

Wall Mount Kit

Pink Accent Rings

Minimum Requirements

• Smartphone or tablet with iPhone / iPad: iOS 5.1.1 or higher; Android

4.01 or higher

• 802.11g/n Wi-Fi network (Wireless N network recommended for

optimal performance)

• Internet access required for remote viewing

Hardware Overview

Front View

Microphone

Focus Ring

Front Accent Ring

Temperature Sensor

Camera Base

Base Accent Ring

Light Sensor

Camera Lens

Night Vision

Lights (IR)

Lullaby/Volume/

Power Buttons

Temperature Indicator

Speaker

microSD Card Slot

Micro-USB

Power Port

Back View Bottom View

Cloud LED

Reset Button

Power LED

Mounting Point

Plug in your camera and wait until the Power LED turns green.

Installation

Download the free mydlink Baby Camera Monitor app on your smartphone

or tablet.

Warning: To prevent your baby from being strangled, please keep all

cables such as the power cable out of your baby’s reach. Cables must be

at least 3 feet from the crib according to the Consumer Product Safety

Commission (CPSC).

You can use the included power adapter, or you can use a portable USB battery (not included)

that can supply 5 V / 2 A of power.

Connect to the Camera’s Wi-Fi signal. The Wi-Fi network name and password

are located on the label on the back of this booklet.

Launch the mydlink Baby app. The app will guide you through the

conguration process.

iPhone/iPad: Settings > Wi-Fi Settings

Android: Settings > Wireless & Networks

> Wi-Fi Settings

Do not overtighten the screws as this may crack the bracket.

Mount the Camera

Please refer to the steps below to assist you with mounting the camera.

We suggest that you congure the camera before mounting.

• Place the wall mount where you want to

position the camera and use a pencil to

mark the holes.

• Use a 6mm drill bit to drill both holes at

least 30mm deep.

• Use a mallet to insert the wall anchors into

the holes.

• Place the mounting base over the holes

that are in the wall.

• Make sure to align the mounting base

holes with the holes in the wall and then

use the supplied screws to attach the

mounting base to the surface of the wall.

Warning: Placing your camera around water may cause accidental shocks.

• Place the base cover over the mounting

base and screw the camera stem into the

mounting base.

• Remove the base from the camera by

simply pulling it o.

• Loosen the collar on the camera stem

and then screw the camera stem into the

bottom of the camera. Turn the securing

wheel to ensure the connection to the

camera is snug.

• Adjust the angle of the camera as desired

and then tighten the collar on the camera

stem to lock it in place.

FAQs

1. The Image is out of focus.

You can turn the white focus ring on the front of the camera to adjust the focus.

2. How do I change the accent rings?

Rotate the access ring counterclockwise, then lift it o. Put the new ring on and rotate

it clockwise until it clicks into place.

3. How do I select a dierent lullaby?

Use the mydlink Baby app to change the lullaby. Click on the music icon on the camera’s

live view screen. Select a lullaby from the list or select to play all.

4. I started the mydlink Baby Camera Monitor app, but I can’t nd my camera.

• Make sure your camera is turned on and receiving power.

• If you are setting up a new camera, make sure your smartphone or tablet is connected

to the camera’s Wi-Fi signal (not your wireless router).

• The Wi-Fi network name should be [myBabyCam-XXXX], where XXXX is a 4-digit code

(the last 4 digits of your camera’s MAC address).

• The Wi-Fi network name and password is printed on a label on the bottom of your

camera and on the back of this install guide.

• If you still can’t nd your camera, reset your camera by pressing its reset button for

10 seconds (while it is powered on).

5. Why is there a white haze when viewing in night vision mode?

The night vision lights on the camera may be reecting o a nearby surface. Try

repositioning and aiming the camera.

Notes

Technical Support

This guide is only for the rst time conguration. Please refer to the user manual to

learn more or visit http://support.dlink.com for more information. Also feel free to

http://support.dlink.com

USA

Version 1.00(US)

September 18, 2013

6DCS825LQN01G

subsidiaries. Other trademarks are the property of their respective owners. Maximum wireless signal rate derived from IEEE

Standard 802.11g and 802.11n specications. Actual data throughput will vary. Network conditions and environmental

factors, including volume of network trac, building materials and construction, and network overhead, lower actual

data throughput rate. Environmental factors will adversely aect wireless signal range. Product specications, size

and shape are subject to change without notice, and actual product appearance may dier from that depicted on the

packaging. Visit dlink.com (US) or dlink.ca (Canada) for more details.

Camera Wi-Fi Network Details:

Your Camera

Password:

D-Link DCS-825L Quick Install Manual

Brand: D-Link

Model: DCS-825L

Category: Baby video monitors

Type: Quick Install Manual

Here are some of the features of the D-Link DCS-825L:

Download PDF

report

D-Link DCS-825L Quick Install Manual

D-Link DCS-825L Quick Install Manual

Related papers

Other documents