Balboa Plug N' Click Heater User manual

Brand: Balboa

Model: Plug N' Click Heater

Type: User manual

Balboa Water Group Plug N' Click Heater is an easy-to-install heater that can be used to heat up your spa or hot tub. It comes with a 3/8” (9.5mm) open end wrench, 3/8” (9.5mm) nut driver, flat-head and Phillips screwdriver. The heater has a power male terminal that you need to apply NYOGEL 760G to before inserting it into the power plug. When you hear a CLICK, this means the power plug is inserted correctly and locked in place. The heater also has 2 sensors that you need to reinsert before you can turn on the power to the system and enjoy your heated spa or hot tub

Balboa Water Group Plug N' Click Heater is an easy-to-install heater that can be used to heat up your spa or hot tub. It comes with a 3/8” (9.5mm) open end wrench, 3/8” (9.5mm) nut driver, flat-head and Phillips screwdriver. The heater has a power male terminal that you need to apply NYOGEL 760G to before inserting it into the power plug. When you hear a CLICK, this means the power plug is inserted correctly and locked in place. The heater also has 2 sensors that you need to reinsert before you can turn on the power to the system and enjoy your heated spa or hot tub

Installation Of A New Plug N’ Click Heater

– Turn off power to the system.

– Using a Phillips screwdriver remove the

2 screws on top of the enclosure and open the cover.

– Locate the 2 sensors holder on the circuit board.

– Remove the 2 heater sensors by depressing the

clip and gently pulling on the wire to remove

each sensor cable.

– Unplug the heater power connector by depressing

the holder clip to release the female connector.

– Remove the 2 heater nuts with a 3/8” (9.5mm)

open wrench.

– Remove heater from system.

PARTS AND TOOLS YOU NEED

– 3/8” (9.5mm) open end wrench

– 3/8” (9.5mm) nut driver

– Flat-head and Phillips screwdriver

– Replacement Balboa Heater

– Nyogel 760G (36308) and a stick

STEP 1 OPEN THE SYSTEM BOX

STEP 3 REMOVE THE 2 HEATER SENSORS

STEP 2 UNPLUG HEATER CONNECTOR

STEP 4 REMOVE NUTS ON HEATER

WARNING!

Please contact an electrician or your local electrical company when

connecting any spa electrical components. DO NOT OPEN THE SPA

SYSTEM AND ATTEMPT TO CONNECT THE CABLE CONNECTORS

YOURSELF. The high electrical voltage will harm or kill you.

Balboa Heater

Nyogel 760G (36308) and a stick

REPLACEHEATER 06/25/2014

©2014 Balboa Water Group. Single Source Solution. All rights reserved.

1382 Bell Avenue | Tustin, CA 92780 | p 714.384.0384 | www.balboawater.com

We reserve the right to change technical data without further notice.

42270_A

– Place your new heater in the system rack. – Tighten the 2 nuts to secure

the heater in place.

– Reinsert your 2 sensors.

STEP 5 INSTALL HEATER CABLES, NUTS AND SENSORS

STEP 6 APPLY NYOGEL 760G TO THE HEATER POWER MALE TERMINAL

STEP 6 REINSERT THE POWER TERMINAL

– Use a ﬂat stick apply NYOGEL 760G

to all 3 sides of the heater

power male terminal.

Apply NYOGEL 760G here.

– Reinsert the heater power plug. When you

hear a CLICK, this means the power plug is

inserted correctly and locked in place.

– Reinsert the spa cover and tighten the 2

screws.

– Turn on power to the system and ENJOY!

PLUG N’

CLICK

Applying NYOGEL

to a stick

1
2

Balboa Plug N' Click Heater User manual

Brand: Balboa

Model: Plug N' Click Heater

Type: User manual

Balboa Water Group Plug N' Click Heater is an easy-to-install heater that can be used to heat up your spa or hot tub. It comes with a 3/8” (9.5mm) open end wrench, 3/8” (9.5mm) nut driver, flat-head and Phillips screwdriver. The heater has a power male terminal that you need to apply NYOGEL 760G to before inserting it into the power plug. When you hear a CLICK, this means the power plug is inserted correctly and locked in place. The heater also has 2 sensors that you need to reinsert before you can turn on the power to the system and enjoy your heated spa or hot tub

Download PDF

Related papers

Other documents