Clarke CDM-45 Operating instructions
- Category
- Multimeters
- Type
- Operating instructions
This manual is also suitable for
DIGITAL
MULTIMETER
OPERATING
INSTRUCTIONS
MODEL CDM-45
Part No.4500065
0404
DIGITAL
MULTIMETER
OPERATING
INSTRUCTIONS
MODEL CDM-45
Part No.4500065
0404
2
The Meter may be hung on a wall,
or supported as shown,
depending upon which support is
used.
The probes may be located as
shown, allowing easy one hand
operation.
GENERAL CHARACTERISTICS
Maximum Display :1999 counts (3½ digits) with auto polarity
indication and eng. unit.
Measuring Method : Dual-Slope integration A-D convertor
system.
Overrange Indication : Figure “1” displayed on the LCD.
Max. common mode voltage : 500V dc/ac rms.
Temp. for guaranteed accuracy : 23OC to ± 5OC.
Temperature Ranges : Operating 0OC to 40OC, 32OF to 104OF.
: Storage-10OC to 50OC, 14OF to 122OF.
Power Supply : 1x 9V battery (NEDA 1604, 6F22 type or
equiv).
Low Battery Indication : - + On left of display.
Dimensions incl. Holster : 201L x 100W x 55H mm.
Weight : 478g (incl. 9 volt battery & holster).
Accessories : Operating manual, set of test leads.
Holster,
PARTS & SERVICE TEL: 020 8988 7400
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]
For Spare Parts and Service, please contact your nearest dealer,
or CLARKE International, on one of the following numbers.
PARTS & SERVICE CONTACTS
11
MAINTENANCE
Battery and/or fuse replacement should only be done after the test leads
have been disconnected.
Battery and Fuse Replacement
Note the condition of the 9-volt battery using the procedure described
above. If the battery needs to be replaced, unscrew the four screws and
remove the back cover. Replace the spent battery with one of the same
type (NEDA.1604, 6F22 or equiv). The same procedure is used to replace
the fuses. Ensure replacements are of the same size and value as the original.
Replacement Parts.
1. Test Leads (pair) Part No. HYTL060
2. Holster (Size A) Part No. HYHT60
Fuse : F200mA / 250V (quick acting)
Temperature Measurement
1. Set the Function switch to OC position and the LCD display will show ambient
temperature.
2. Insert the ‘K’ type thermocouple into the TEMP socket and contact the object
to be maesured with the thermocouple probe. Read the display.
WARNING. To avoid an electric shock, ensure the therrmocouple has been
removed before changing to another function.
Frequency Measurement
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the VΩ Hz jack
2. Set the Function switch to 20kHz and connect test leads across the source or
load under measurement.
NOTE:
1. Reading is possible above 10V rms, but accuracy is not guaranteed.
2. in a noisy environment, it is preferable to use shielded cable to measure small
signals.
2
The Meter may be hung on a wall,
or supported as shown,
depending upon which support is
used.
The probes may be located as
shown, allowing easy one hand
operation.
GENERAL CHARACTERISTICS
Maximum Display :1999 counts (3½ digits) with auto polarity
indication and eng. unit.
Measuring Method : Dual-Slope integration A-D convertor
system.
Overrange Indication : Figure “1” displayed on the LCD.
Max. common mode voltage : 500V dc/ac rms.
Temp. for guaranteed accuracy : 23OC to ± 5OC.
Temperature Ranges : Operating 0OC to 40OC, 32OF to 104OF.
: Storage-10OC to 50OC, 14OF to 122OF.
Power Supply : 1x 9V battery (NEDA 1604, 6F22 type or
equiv).
Low Battery Indication : - + On left of display.
Dimensions incl. Holster : 201L x 100W x 55H mm.
Weight : 478g (incl. 9 volt battery & holster).
Accessories : Operating manual, set of test leads.
Holster,
PARTS & SERVICE TEL: 020 8988 7400
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]
For Spare Parts and Service, please contact your nearest dealer,
or CLARKE International, on one of the following numbers.
PARTS & SERVICE CONTACTS
11
MAINTENANCE
Battery and/or fuse replacement should only be done after the test leads
have been disconnected.
Battery and Fuse Replacement
Note the condition of the 9-volt battery using the procedure described
above. If the battery needs to be replaced, unscrew the four screws and
remove the back cover. Replace the spent battery with one of the same
type (NEDA.1604, 6F22 or equiv). The same procedure is used to replace
the fuses. Ensure replacements are of the same size and value as the original.
Replacement Parts.
1. Test Leads (pair) Part No. HYTL060
2. Holster (Size A) Part No. HYHT60
Fuse : F200mA / 250V (quick acting)
Temperature Measurement
1. Set the Function switch to OC position and the LCD display will show ambient
temperature.
2. Insert the ‘K’ type thermocouple into the TEMP socket and contact the object
to be maesured with the thermocouple probe. Read the display.
WARNING. To avoid an electric shock, ensure the therrmocouple has been
removed before changing to another function.
Frequency Measurement
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the VΩ Hz jack
2. Set the Function switch to 20kHz and connect test leads across the source or
load under measurement.
NOTE:
1. Reading is possible above 10V rms, but accuracy is not guaranteed.
2. in a noisy environment, it is preferable to use shielded cable to measure small
signals.
INTRODUCTION
Thank you for purchasing this Clarke Multi-Range Digital Multimeter.
This instrument is a compact, rugged, battery operated hand held 3½ digit,
digital multimeter. It is designed to measure AC and DC voltage, AC and
DC current, Resistance, Diode, Capacitance and for testing Transistors,
Continuity, and Thermocouple temperature.
The dual-slope A-D converter uses C-MOS technology for auto zeroing,
polarity selection and over-range indication.
It is an ideal instrument for use in the field, laboratories, workshops, and for
hobby and home applications.
GUARANTEE
This product is guaranteed against faults in manufacture for 12 months from
purchase date. Please keep your receipt as proof of purchase.
This guarantee is invalid if the product has been abused or tampered with
in any way, or not used for the purpose for which it is intended.
The reason for return must be clearly stated.
This guarantee does not affect your statutory rights.
FEATURES
• Push button ON/OFF power switch.
• Auto Power OFF after approx 40 min.
• Single 32 position rotary switch for FUNCTION and RANGE selection.
• Auto over-range indication, with “1” being displayed on the LCD.
• Automatic reverse polarity indication on DC ranges.
• All ranges (except 10A current ranges) fully protected.
• DC Voltage measurement 200mV to 1,000V.
• AC Voltage measurement 2mV to 700V rms.
• DC current measurement 20µA to 10A.
• AC current measurement 200µA to 10A rms.
• Resistance measurement 200Ω to 200MΩ.
• Diode testing with 1mA fixed current.
• Transistor hFE test with 10µA
• Temperature measurement.
• Frequency measurement.
• Holster with 2 position stand, and test lead holders to ease the taking
of readings whilst holding the meter.
3
Note:
1. If the resistance value being measured exceeds the maximum value of
the range selected, an over-range indication will be displayed(“1”).
Select a higher range.
For resistance of approx. 1 Megohm and above, the meter may take a
few seconds to become stable. This is normal for high resistance readings.
2.. When the input is not connected, i.e. an open circuit, the figure’1’ will be
displayed for an over-range condition.
3. When testing in-circuit resistance, ensure all power has been removed
and all capacitors are fully discharged.
4. When using the 200Megohm range, the display is 10 counts. These counts
must be subtracted from the reading.... eg. when measuring a 100MW
resistance, the reading will display 101.0.
The correct measuring result iis 101.0 - 1.0 = 100MW
Diode Measurement
1. Connect the BLACK test lead to the COM jack and the RED test lead to the
V/Ω jack.
(Note: The polarity of the RED test lead is “+”).
2. Set the FUNCTION switch to the position and connect the test
leads across the diode under test, red lead to the anode, black to the
cathode. Display shows the approx. forward voltage drop of the diode.
Continuity Test.
1. Connect the BLACK test lead to the COM jack and the RED test lead to the
V/Ω jack.
(Note: The polarity of the RED test lead is “+”).
2. Set the FUNCTION switch to the position and Connect the test
leads to two points of circuit, if the resistance is lower than approx. 70Ω,
the buzzer sounds.
10
Transistor hFE Test
1. Set the FUNCTION switch to the hFE range.
2. Determine whether the transistor is NPN or PNP and locate the Emitter,
Base and Collector leads. Insert the leads into the proper holes in the
socket on the front panel.
3. Display will read approx. hFE value at the test condition/Base Current
10µA VCE 3.2V
INTRODUCTION
Thank you for purchasing this Clarke Multi-Range Digital Multimeter.
This instrument is a compact, rugged, battery operated hand held 3½ digit,
digital multimeter. It is designed to measure AC and DC voltage, AC and
DC current, Resistance, Diode, Capacitance and for testing Transistors,
Continuity, and Thermocouple temperature.
The dual-slope A-D converter uses C-MOS technology for auto zeroing,
polarity selection and over-range indication.
It is an ideal instrument for use in the field, laboratories, workshops, and for
hobby and home applications.
GUARANTEE
This product is guaranteed against faults in manufacture for 12 months from
purchase date. Please keep your receipt as proof of purchase.
This guarantee is invalid if the product has been abused or tampered with
in any way, or not used for the purpose for which it is intended.
The reason for return must be clearly stated.
This guarantee does not affect your statutory rights.
FEATURES
• Push button ON/OFF power switch.
• Auto Power OFF after approx 40 min.
• Single 32 position rotary switch for FUNCTION and RANGE selection.
• Auto over-range indication, with “1” being displayed on the LCD.
• Automatic reverse polarity indication on DC ranges.
• All ranges (except 10A current ranges) fully protected.
• DC Voltage measurement 2mV to 1,000V.
• AC Voltage measurement 200mV to 700V rms.
• DC current measurement 20µA to 10A.
• AC current measurement 200µA to 10A rms.
• Resistance measurement 200Ω to 200MΩ.
• Diode testing with 1mA fixed current.
• Transistor hFE test with 10µA
• Temperature measurement.
• Frequency measurement.
• Holster with 2 position stand, and test lead holders to ease the taking
of readings whilst holding the meter.
3
Note:
1. If the resistance value being measured exceeds the maximum value of
the range selected, an over-range indication will be displayed(“1”).
Select a higher range.
For resistance of approx. 1 Megohm and above, the meter may take a
few seconds to become stable. This is normal for high resistance readings.
2.. When the input is not connected, i.e. an open circuit, the figure’1’ will be
displayed for an over-range condition.
3. When testing in-circuit resistance, ensure all power has been removed
and all capacitors are fully discharged.
4. When using the 200Megohm range, the display is 10 counts. These counts
must be subtracted from the reading.... eg. when measuring a 100MW
resistance, the reading will display 101.0.
The correct measuring result iis 101.0 - 1.0 = 100MW
Diode Measurement
1. Connect the BLACK test lead to the COM jack and the RED test lead to the
V/Ω jack.
(Note: The polarity of the RED test lead is “+”).
2. Set the FUNCTION switch to the position and connect the test
leads across the diode under test, red lead to the anode, black to the
cathode. Display shows the approx. forward voltage drop of the diode.
Continuity Test.
1. Connect the BLACK test lead to the COM jack and the RED test lead to the
V/Ω jack.
(Note: The polarity of the RED test lead is “+”).
2. Set the FUNCTION switch to the position and Connect the test
leads to two points of circuit, if the resistance is lower than approx. 70Ω,
the buzzer sounds.
10
Transistor hFE Test
1. Set the FUNCTION switch to the hFE range.
2. Determine whether the transistor is NPN or PNP and locate the Emitter,
Base and Collector leads. Insert the leads into the proper holes in the
socket on the front panel.
3. Display will read approx. hFE value at the test condition/Base Current
10µA VCE 3.2V
SAFETY PRECAUTIONS
Read this information before using the meter, taking special care regarding
any WARNING or IMPORTANT notices. The following safe practices and proper
operating procedures should be followed when using any multimeter:
•Inspect the test leads for insulation damage or exposed metal.
Damaged leads should be replaced.
•Select the proper function and range tor your measurement.
•Avoid severe shocks and do not drop the multimeter.
•Do not allow the meter to be used if it is damaged or if its safety is impaired
•WARNING: To AVOID ELECTRIC SHOCK, USE CAUTION WHEN WORKING
ABOVE 40V DC OR 25V AC RMS. SUCH VOLTAGES POSE A SHOCK HAZARD.
•Electrically disconnect the live, or hot test lead before disconnecting
the common test lead.
•Follow all equipment safety procedures. Disconnect the input power
and discharge all high-voltage capacitors through a protective
impedance before testing in Ω and with the multimeter.
•Avoid working alone.
•When making a current measurement, turn the power off before
connecting the multimeter in the circuit. Overloading a current shunt
will cause excessive heat.
•When measuring transformer secondary or motor winding current, check
the multimeter fuses first.
•When testing circuits take extra care not to touch any bare metal
including the ends of the test probes.
•The use of makeshift fuses and the short-circuiting of fuse holders is prohibited.
•Whenever it is likely that the protection has been impaired, the meter shall
be made inoperative and be secured against any unintended operation.
•Never attempt to measure a voltage or current higher than the maximum
rating of the meter.
•Never perform resistance measurements on a live circuit.
4
DC Current Measurement
WARNING, Do not attempt to measure a current in excess of 10 Amps
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the mA jack for a maximum of 2A. For inputs greater than 10A, move
the red test lead to the 10A jack.
2. Set the FUNCTION switch to the A --- range to be used and connect the
test leads in series with the load under measurement. Reverse polarity is
indicated by a “—” sign being displayed in front of the reading.
Note:
1. If the current range is not known beforehand, set the FUNCTION switch
to a high range and work down.
2. When only the figure “1” is displayed over range is being indicated and the
FUNCTION switch must be set to a higher range.
3. The maximum input current is 2A, or 10A depending on the jack used.
Excessive current will blow the fuse which must be replaced. The 10A
range is not protected by a fuse. The fuse rating should be 2A and
no more to prevent damage to the internal circuitry. The maximum
terminal voltage drop is 200mV.
AC Current measurement
WARNING, Do not attempt to measure a current in excess of 10 Amps
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the mA jack for a maximum of 2A. For a maximum of 10A, move the
RED test lead to the 10A jack.
2. Set the FUNCTION switch to the A~ range to be used and connect the
test lead in series with the load to be measured.
Note: See DC Current Note 1 - 3
Resistance Measurement
IMPORTANT. When checking in-circuit resistance, ensure the circuit under test
has all power removed and that all capacitors are fully discharged.
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the V/Ω jack. Note
: the polarity of the RED test lead is “+”.
2. Set the FUNCTION switch to the range to be used and connect the test
leads across the resistance to be measured.
9
SAFETY PRECAUTIONS
Read this information before using the meter, taking special care regarding
any WARNING or IMPORTANT notices. The following safe practices and proper
operating procedures should be followed when using any multimeter:
•Inspect the test leads for insulation damage or exposed metal.
Damaged leads should be replaced.
•Select the proper function and range tor your measurement.
•Avoid severe shocks and do not drop the multimeter.
•Do not allow the meter to be used if it is damaged or if its safety is impaired
•WARNING: To AVOID ELECTRIC SHOCK, USE CAUTION WHEN WORKING
ABOVE 40V DC OR 25V AC RMS. SUCH VOLTAGES POSE A SHOCK HAZARD.
•Electrically disconnect the live, or hot test lead before disconnecting
the common test lead.
•Follow all equipment safety procedures. Disconnect the input power
and discharge all high-voltage capacitors through a protective
impedance before testing in Ω and with the multimeter.
•Avoid working alone.
•When making a current measurement, turn the power off before
connecting the multimeter in the circuit. Overloading a current shunt
will cause excessive heat.
•When measuring transformer secondary or motor winding current, check
the multimeter fuses first.
•When testing circuits take extra care not to touch any bare metal
including the ends of the test probes.
•The use of makeshift fuses and the short-circuiting of fuse holders is prohibited.
•Whenever it is likely that the protection has been impaired, the meter shall
be made inoperative and be secured against any unintended operation.
•Never attempt to measure a voltage or current higher than the maximum
rating of the meter.
•Never perform resistance measurements on a live circuit.
4
DC Current Measurement
WARNING, Do not attempt to measure a current in excess of 10 Amps
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the mA jack for a maximum of 2A. For inputs greater than 10A, move
the red test lead to the 10A jack.
2. Set the FUNCTION switch to the A --- range to be used and connect the
test leads in series with the load under measurement. Reverse polarity is
indicated by a “—” sign being displayed in front of the reading.
Note:
1. If the current range is not known beforehand, set the FUNCTION switch
to a high range and work down.
2. When only the figure “1” is displayed over range is being indicated and the
FUNCTION switch must be set to a higher range.
3. The maximum input current is 2A, or 10A depending on the jack used.
Excessive current will blow the fuse which must be replaced. The 10A
range is not protected by a fuse. The fuse rating should be 2A and
no more to prevent damage to the internal circuitry. The maximum
terminal voltage drop is 200mV.
AC Current measurement
WARNING, Do not attempt to measure a current in excess of 10 Amps
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the mA jack for a maximum of 2A. For a maximum of 10A, move the
RED test lead to the 10A jack.
2. Set the FUNCTION switch to the A~ range to be used and connect the
test lead in series with the load to be measured.
Note: See DC Current Note 1 - 3
Resistance Measurement
IMPORTANT. When checking in-circuit resistance, ensure the circuit under test
has all power removed and that all capacitors are fully discharged.
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the V/Ω jack. Note
: the polarity of the RED test lead is “+”.
2. Set the FUNCTION switch to the range to be used and connect the test
leads across the resistance to be measured.
9
Input Impedance: 10M ohms on all ranges.
Frequency Range: 40Hz to 400 Hz
Overload Protection: 700V RMS or 1000V peak continuous on
AC ranges, except 200mV AC range
(15 sec. max. above 300V RMS).
SPECIFICATIONS
Accuracies are ± (% reading ± the number indicated in the
respective chart, added or deducted from the digit, or right hand
column of the reading)
AC Voltage
2mV
2V
20V
200V
700V
Range Accuracy Resolution
±0.8% of rdg ± 3 digits
±1.2% of rdg ± 3 digits
100µA
1mV
10mV
0.1V
1V
5
Input Impedance: 10M ohms on all ranges.
Overload Protection: 220V RMS on 200mV range and 1000V DCor
peak AC all others
± 0.8 of rdg ± 2 digit
200mV
2V
20V
200V
1000V
100µV
1mV
10mV
0.1V
1V
Range Accuracy Resolution
±0.5% of rdg ± 1 digit
DC Voltage
±1.2% of rdg ± 3 digits
1. Check the 9-volt battery by setting the ON-OFF switch to ON, if the
battery is weak, a + - sign will appear on the display. If this does not
appear on the display, proceed as below. See MAINTENANCE if the
battery has to be replaced.
2. The mark, or symbol, next to the test lead jacks, is a warning that the
input voltage or current should not exceed the indicated values, to
prevent damage to internal circuitry.
3. The function switch should be set to the range which you want to test
before operation.
DC Voltage Measurement
WARNING. Use extreme caution measuring high voltages, and do not
attempt to measure voltages greater than 1000 Volts, as this can
damage internal circuitry.
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the V/Ω jack.
2. Set FUNCTION switch to V --- range to be used and connect test leads
across source or load. Reverse polarity is indicated by a “—” sign being
displayed in front of the reading.
Note:
1. If voltage range is not known beforehand, set the FUNCTION switch to a
high range and work down.
2. When only the figure “1” is displayed, over-range is being indicated,
and the FUNCTION switch must be set to a higher range.
AC Voltage Measurement
WARNING. Use extreme caution measuring high voltages, and do not
attempt to measure voltages greater than 700 Volts RMS, as this can
damage internal circuitry.
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the V/Ω jack.
2. Set the FUNCTION switch to the V~ range to be used and connect the
test leads across the source or load under measurement.
Notes: See DC Voltage measurement Note 1.2.
OPERATION
8
Input Impedance: 10M ohms on all ranges.
Frequency Range: 40Hz to 400 Hz
Overload Protection: 700V RMS or 1000V peak continuous on
AC ranges, except 200mV AC range
(15 sec. max. above 300V RMS).
SPECIFICATIONS
Accuracies are ± (% reading ± the number indicated inh the
respective chart, added or dxceducted from the digit, or right
hand column of the reading)
AC Voltage
2mV
2V
20V
200V
700V
Range Accuracy Resolution
±0.8% of rdg ± 3 digits
±1.2% of rdg ± 3 digits
100µA
1mV
10mV
0.1V
1V
5
Input Impedance: 10M ohms on all ranges.
Overload Protection: 220V RMS on 200mV range and 1000V DCor
peak AC all others
± 0.8 of rdg ± 2 digit
200mV
2V
20V
200V
1000V
100µV
1mV
10mV
0.1V
1V
Range Accuracy Resolution
±0.5% of rdg ± 1 digit
DC Voltage
±1.2% of rdg ± 3 digits
1. Check the 9-volt battery by setting the ON-OFF switch to ON, if the
battery is weak, a + - sign will appear on the display. If this does not
appear on the display, proceed as below. See MAINTENANCE if the
battery has to be replaced.
2. The mark, or symbol, next to the test lead jacks, is a warning that the
input voltage or current should not exceed the indicated values, to
prevent damage to internal circuitry.
3. The function switch should be set to the range which you want to test
before operation.
DC Voltage Measurement
WARNING. Use extreme caution measuring high voltages, and do not
attempt to measure voltages greater than 1000 Volts, as this can
damage internal circuitry.
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the V/Ω jack.
2. Set FUNCTION switch to V --- range to be used and connect test leads
across source or load. Reverse polarity is indicated by a “—” sign being
displayed in front of the reading.
Note:
1. If voltage range is not known beforehand, set the FUNCTION switch to a
high range and work down.
2. When only the figure “1” is displayed, over-range is being indicated,
and the FUNCTION switch must be set to a higher range.
AC Voltage Measurement
WARNING. Use extreme caution measuring high voltages, and do not
attempt to measure voltages greater than 700 Volts RMS, as this can
damage internal circuitry.
1. Connect the BLACK test lead to the COM jack and the RED test lead to
the V/Ω jack.
2. Set the FUNCTION switch to the V~ range to be used and connect the
test leads across the source or load under measurement.
Notes: See DC Voltage measurement Note 1.2.
OPERATION
8
Resistance
Range Accuracy Resolution
±0.8% of rdg ± 3 digits
±0.8% of rdg ± 1 digit
0.1Ω
1Ω
10Ω
100Ω
1KΩ
10KΩ
100KΩ
200Ω
2KΩ
20KΩ
200KΩ
2MΩ
20MΩ
200MΩ
± 1% of rdg ± 2 digits
Overload Protection: 220V DC/RMS. AC on all ranges
Open Circuit Voltage: Lower than 700mV
±5% of rdg-10 dig ±10 dig
Thermocouple Temperature
- 20O C - 0O C ±5% of rdg ± 4 digits 1O C
0O C - 400O C ±1% of rdg ± 3 digits 1O C
400O C - 1000O C ±2% of rdg 1O C
Range Temp. Range Accuracy Res.
-20OC to
1000OC
Range Accuracy Resolution
20nF
200nF
2µF
20µF
±4% of rdg ± 3 digits
10µF
0.1nF
1nF
10nF
2nF 1µF
Capacitance
7
DC Current
AC Current
Overload Protection: 20mA/250V fuse
Frequency Range: 40Hz to 400Hz.
Max. Input Current: 10A
Indication: Average. (RMS of sine wave)
6
Overload Protection: 20mA/250V fuse
Max. Input Current: 10A
20mA
200mA
10A
±0.8% of rdg ± 1 digit
±1.5% of rdg ± 1 digit
10µA
0.1mA
10mA
±2% of rdg ± 5 digits
2mA 1µA
Range Accuracy Resolution
Range Accuracy Resolution
Range Accuracy Resolution
20kHz 10µA
Frequency
±1.5% of rdg ± 5 digits
Sensitivity: 200mV rms. Input, no more than 10V rms
20mA
200mA
10A
±1% of rdg ± 3 digits
±1.8% of rdg ± 3 digits
10µA
0.1mA
10mA
±3% of rdg ± 7 digits
Resistance
Range Accuracy Resolution
±0.8% of rdg ± 3 digits
±0.8% of rdg ± 1 digit
0.1Ω
1Ω
10Ω
100Ω
1KΩ
10KΩ
100KΩ
200Ω
2KΩ
20KΩ
200KΩ
2MΩ
20MΩ
200MΩ
± 1% of rdg ± 2 digits
Overload Protection: 220V DC/RMS. AC on all ranges
Open Circuit Voltage: Lower than 700mV
±5% of rdg-10 dig ±10 dig
Thermocouple Temperature
- 20O C - 0O C ±5% of rdg ± 4 digits 1O C
0O C - 400O C ±1% of rdg ± 3 digits 1O C
400O C - 1000O C ±2% of rdg 1O C
Range Temp. Range Accuracy Res.
-20OC to
1000OC
Range Accuracy Resolution
20nF
200nF
2µF
20µF
±4% of rdg ± 3 digits
10µF
0.1nF
1nF
10nF
2nF 1µF
Capacitance
7
DC Current
AC Current
Overload Protection: 20mA/250V fuse
Frequency Range: 40Hz to 400Hz.
Max. Input Current: 10A
Indication: Average. (RMS of sine wave)
6
Overload Protection: 20mA/250V fuse
Max. Input Current: 10A
20mA
200mA
10A
±0.8% of rdg ± 1 digit
±1.5% of rdg ± 1 digit
10µA
0.1mA
10mA
±2% of rdg ± 5 digits
2mA 1µA
Range Accuracy Resolution
Range Accuracy Resolution
Range Accuracy Resolution
20kHz 10µA
Frequency
±1.5% of rdg ± 5 digits
Sensitivity: 200mV rms. Input, no more than 10V rms
20mA
200mA
10A
±1% of rdg ± 3 digits
±1.8% of rdg ± 3 digits
10µA
0.1mA
10mA
±3% of rdg ± 7 digits
-
1
-
2
-
3
-
4
-
5
-
6
Clarke CDM-45 Operating instructions
- Category
- Multimeters
- Type
- Operating instructions
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
