Response QC 3674 Operation Instruction Manual

Brand: Response

Model: QC 3674

Category: Security cameras

Type: Operation Instruction Manual

Installation and Operating Instructions

These instructions should be retained in a safe place for future reference.

CONTENTS

1. PLANNING YOUR LAYOUT (3)

2. KIT CONTENTS (5)

3. INSTALLATION (8)

4. CAMERA SETUP (9)

5. ABOUT DIGITAL WIRELESS TECHNOLOGY (12)

6. PRODUCT SPECIFICATION (13)

PLANNING YOUR LAYOUT:

SAFETY AND INSTALLATION TIPS:

DVR

• keep away from heat sources and high temperature places

• Avoid direct sunlight

• Avoid humid places

• avoid vibration

• Install in a ventilated environment

• do not replace the supplied 2GB memory card with a greater capacity(the unit may

fail to operate properly).

TV/Monitor

Receiver

DVR

Front Door

Camera 2

Camera 1

Max 5m

Max 5m Max 5m

Max 5m

Ensure the distance from camera to power

outlet does not exceed the length of the

camera power adapter cable

15mm diameter

cable hole

(to allow camera

cable and connector

to pass through)

Camera(s) and DVR

NIGHT VISION:

Do not attempt to open the units with the power adaptor plug connected to avoid any risk

of personal injury.

When installing CCTV camera(s), always foloow manufacturer's advice when using

power tools, steps, ladders, etc. and wear suitable protective equipment (e.g. safety

goggles)when drilling holes. Before drilling holes through walls check for hidden

electricity cables and water pipes. The use of cable/pipe detector is advisable.

It is also advisable to avoid exposing any cameras to extreme weather conditions (e.g,

under a gutter which is prone to any water leaks). When installing any cameras with this

unit, it is advisable to use cable conduit to protect any video/power extension cables

from being exposed externally and to prevent/reduce the chances of the cables being

tampered with. After drilling any hole though an external wall for a cable, ensure the hole

is sealed up around the cable using a sealant to prevent drafts.

To prevent a re or electrical shock hazard, do not attempt to open the housing while

the unit is exposed to rain, water or wet conditions. There are no user serviceable

parts inside. Refer servicing to qualified service personnel. Avoid pointing the

camera(s) directly at the sun or any bushes, tree branches or moving objects that might

unnecessary cause the DVR to record due to winds for example. System also provides

"Masking" function, user may screen out motion detection area in parts of the picture

which motion detection is not required.

The camera has built-in infra-red LEDs to allow you to view at night for 24hrs

surveillance. The LEDs will automatically activate at night and the picture viewed will turn

to black and whit. The night viewing range is up to 7m.

 x Digital Wireless Camera

 x 5V/1A Power Adapter



x Camera Stand

x )L[LQJ3DFN

x Camera Antenna

x Manual

Tools Required:

Electric drill

5mm masonry drill bit

15mm masonry drill bit

No. 2 Philips screwdriver

KIT CONTENTS

Digital Wireless Camera

5V/1A Power Adapter for

Camera and Receiver

)L[LQJ3DFN

Camera Stand

Camera Antenna

Manual

Digital Wireless Colour Camera

Recordable CCTV Kit

Installation and Operating Instructions

YOUR HELPLINE 0844 736 9149

www.friedland.co.uk

Lines open Monday to Friday 9.00am to 5.00pm. Calls charged at local rates.

These instructions should be retained in a safe place for future reference.

Setting the Camera Channel

Pairing the Camera to Receiver (Optional)

The wireless monitor support up to 4 wireless cameras. Follow the step below to set or

change the monitor channel of the camera. If you are adding another camera to link with the

supplied monitor in this kit, then ensure its channel is set to a different channel to the existing

camera(s).

Follow the steps in CAMERA SETUP section

to set or change the channel of the camera. If

you are adding another camera to link with the supplied receiver in this kit, then ensure its

channel is set to a different channel to the existing camera(s).

Pairing Key

INSTALLATION

Attach Stand to Mounting Surface

A.Secure camera stand on the wall

B. Loosen up the Thumb screw

C.Adjust proper view angle then secure the joint with T-bolt.

CAMERA INSTALLATION

Select CAMERA SETUP, press MENU key once to enter sub-menu.

CAMERA SETUP

Use▼▲to select the camera to set up (1-4).

Use◄►to select [PAIRING] [BRIGHTNESS] [CAMERA ON/OFF]

Camera Pairing

With PAIRING section highlighted, press MENU key once to begin camera pairing (pair

LED on camera will blink once and following with LED blinking continuously indicating

data transmission in process.

System will conrm pairing process is successful with "PAIRED" displaying on screen.

System will indicate pairing process failed with "PAIRING FAIL" displaying on screen.

Press ESC to return to main menu.

With BRIGHTNESS section highlighted, use ▼▲ to adjust camera brightness.

Press ESC to return to main menu.

Camera Brightness Adjustment

With ACTIVATION section highlighted, use ▼▲ to enable or disable camera.

Press ESC to return to main menu.

NOTE:

Make sure camera(s) paired is enabled for SCAN or QUAD to function properly

(camera "ON" can only be selected when camera has been paired to system.).

Camera Activation

About Digital Wireless Technology

This section offers some helpful in for mation to overcome most of the

problems you may encounter. We hope this section can help you to enjoy

a pleasant setup.

Problems Diagnosis

About 2.4GHz Digital Wireless Signal

How to improve the wireless signal quality?

Why Image Compression?

This innovative digital wireless solution integrates advance Frequency

Hopping Spread spectrum (FHSS) technology. This technology greatly

reduce the interference that comes from other devices using the same

radio frequency (2.4GHz), e.g. WIFI, Bluetooth, Zigbee, cordless

phone...etc. You now can enjoy a more pleasant wireless surveillance

quality without flicking and noisy image. However, weaker signal (lag

or still image) can be observed yet from time to time, depending on the

environment where the sysgtem is installed.

complied with FCC part 15.247,ETSI(EN)300 328, audio / video signals

transmitted out about or over 500 foot / 150metre in line of sight should

be supported. Line of sign installatiom, though, is usually not a common

practice. Factors affecting transmission include microwave ovens or other

high frequency electromagnetic waves. Reinforced concrete walls, large

scale metal products and metal furniture should not be located near the

camera or the receiver. Water creates an obstacle and should not be

placed neqr. Human bodies such as a person passing through may cause

unstable signal quality

If possible, remove obstacles in between cam era and receiver that might

reect the signal. These could include fumiture, cabinets, and walls. If you

feel the wireless signal is not improvement. Or simply relocate the camera

closer to the receiver.

In order to provide a private and interference free wireless service,

this digital wireless solution works on a 2Mb narrow hopping band,

Different from traditional 2.4GHz analog signal, this digital wireless signal

is compressed and presented as Motion JPEG(MJPEG) format. By

digitalizing and compressing the raw analog data, the bandwidth is used

more efficiently and securely. Consequentially, you might observe an

indent image line on a larger display monitor or plasma TV.

Product Specication

Camera

Maximum Channels 4

Communication Range 150 metres in open space

Monitor Resolution 800X480

Camera Resolution 640X480

Operating Temperature -10°C ~ 50°C

Operating Voltage DC 5V / 1A

Curren Consumption 550mA(max)

Night Vision 5m

Dimension 123x65x65 mm

Response QC 3674 Operation Instruction Manual

Brand: Response

Model: QC 3674

Category: Security cameras

Type: Operation Instruction Manual

Download PDF

report

Response QC 3674 Operation Instruction Manual

Response QC 3674 Operation Instruction Manual

Related papers

Other documents