www.GEApp/iances.com
©
Safety Instructions ......... 2, 3
Operating Instructions
Controls_Control I{a]obs .... 8, 9
Controls---Touch Pads ....... 4-6
Care and Cleaning
Air Filter ................... ] ]
Front Grille ................. 10
Grille and Case .............. 10
Outdoor Coils ............... l 0
Installation Instructions
Before You Begin .......... 19, 13
Installing a .[-Model in
an Existing _4'all Case ......... 14
Through-the-_'all
Installation--Optional ........ 15
Window Installation--
Optional on models
so equipped .............. 16-91
Troubleshooting Tips ........ 92
Nomml Operating Sounds .... 92
Consumer Support
Consumer Support ... Back Co_er
_A'anantv ................... 93
Coo[ O_d) :
H_a_ P_mp:
Espahol
For a Spanish version of this manual, visit
our VVebsite at _vw.GEAppliances.com.
Para consuhar una version en espaflol de
este manual de instrucciones, visim nuestro
sido de internet www.GEAppliances.com.
Fran_aise
For a French version of this manual, visit
our _:ebsite at w_w.GEAppliances.com.
Pour une version flangaise de ce manuel
d'utilisation, veuillez visitor notre site web
l'adresse www.GEAppliances.com.
Write the modeland serial
numbers here:
Model #
Serial #
Fim_dthese mmJ)ers om_a label on
the {ixm t o{ th e base [m N_behim_ d
the t_'ont g_i]]e.
TINSEA380JBRZ 49-7512 07-05 Jfl
IMPORTANTSAFETYINFORMATION.
READALLINSTRUCTIONSBEFOREUSING.
WARNING'!
For your safe_ the information in this manual must be followed to minimize the risk of fire, electric
shock or personal injury.
SAFETYPRECAUTIONS
iiiiiiiiiiii_iii
iiiiiiiiiiii_iii
iiiiiiiiiiii_iii
Use this appliance only %r its intended
pml)ose as described in this Owner's
Manua].
This air conditioner must be properly
installed in accordance with the
Installation Instructions before it is used.
Ne_er unplug your air conditioner by
pulling on tim power cord. Always glip
plug firefly and pull straight out fiom the
receptacle.
Repair or replace immediately all elecuic
service cords that haxe become fiwed or
otherwise damaged. Do not use a cord
that shows cracks or abrasion damage
along its length or at either the plug or
connector end.
Turn the mode control OR=and unplug
your air conditioner before making any
repairs or cleaning.
NOTE:Westronglyrecommendthat anyservicing
beperformedbya qualifiedindividual.
For your safety...do not store or use
combustible materials, gasoline or oflmr
flammable vapors or liquids in the vicinity
of this or any other appliance.
All air conditioners contain refi-igerants,
which under federal law must be remoxed
prior to product disposal. If you are getting
rid of an old product with refcigerants,
check with the company handling disposal
about what to do.
HOWTOCONNECTELECTRICITY
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
For personal safety, this appliance must be
properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which
mates with a standard 3-prong (grounding)
wall outlet m minimize rite possibility of
electric shock hazard from dlis appliance.
Power cord may include a cmxent
intemq)ter device. A test and reset button is
provided on the plug case. The device should
be tested on a periodic basis by first pressing
the TESTbutton and then the RESErbutton.
If the rESTb, tto, does not trip or if the
RESt'button will not stay engaged,
discontinue use of the air conditioner
and contact a qualified service technician.
Haxe the wall outlet and circuit checked
by a qualified electrician to make sure the
outlet is properly grounded.
'_&'herea 9-prong wall outlet is encountered,
it is your personal responsibility and
obligation to haxe it replaced with a properly
grounded 3-piong wall outlet.
The air conditioner shou]d alwws be plug\g_d
into its own individual electrica] outlet which
has a x_ltag> rating flint matches file rating
plate.
This provides the best perfommnce and also
prevents oxerloading house wiring circuits
which could cause a fire hazard from
oxerheated x_,ires.
See the Installation Instructions, Electrical
Requirements section for specific electrical
connection requirements.
2
www.GEAppliances.com
WARNING!
USEOFEXTENSIONCORDS--115-Voltmodelsonly
Because of potential safety hazards under
certain conditions, we strongly recommend
against the use of an extension cord.
Howe_; ifvo/l Ill/lSt use all extension cord,
it is absolutely necessal T that it be a UL-listed,
14 gauge, 3-wire grounding type appliance
extension cord having a grounding type plug
and outlet and that file electrical radng of
the cord be 15 amperes (minimum) and
125 x_lts.
CAUtiON:
DONOT use an extension cord with any ofthe
230/208 volt models.
USEOFADAPTERPLUGS--115-Voltmodelsonly
Because of potential safety hazards under
certain conditions, we strongly recommend
against the use of an adapter plug.
Howex>i; if you must use an adaptei; where
local codes permit, a temporary connection
may be made m a properly grounded
9-prong wall outlet by use of a UiAismd
adaptor available at most local hardware
stores.
When disconnecting die power cord fiom
the adapter; always hold the adaptor in place
with one hand while pulling the power cord
plug with the other hand. If this is not done,
the adapter ground te_ninal is x>tT likely to
break with repeated use.
If the adapter ground temfinal breaks,
DONOTUSEthe air conditioner until a
proper gTound has been established.
The larger slot in file adaptor must be
aligned with the larger slot in die wall
outlet m provide proper polarity in the
connec6on of the power cord.
Attachingtheadaptergroundtermbal to a waft
outlet coverscrewdoesnotgroundtheappliance
unlessthecoverscrewis metal,notlesulated,and
thewaftoutlet isgroundedthroughthehousewiring.
Youshouldhavethe circuitcheckedbya qualified
electriciantomakesuretheoutlet isproperly
grounded.
READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.
SAVETHESEINSTRUCtiONS
3
Aboutthecontrolsontheair conditioner--modelswith touchpads.
Appearance may vary.
]
Air ConditionerControls
Lightsbesidethetouchpadsonthe airconditioner
controlpanelindicatetheselectedsettings.
RemoteControl
Controls
Whenthe airconditioneristurnedon,it will
automaticallystartin thesettinglastused.
O ON/ITOPo o
Turn,_ air c nditi net on and off.
Display
_k MODE
r On tile remote control, rise to set tile air
conditioner to COOL or FANmode.
On tile air conditioner controls, use to set
COOLor FANmode at HIGH,MED or LOW
tim speed. Indicator lights on tile air
conditioner controls will show tile mode
and tan speed selected.
O TEMP Increase •/Decrease • Pads
Use to set temperature when in COOL
illode,
O an Speeds (Remote controlonly)
Use to set tile tim speed at LOW,MEDor
HIGH.
O TIMER
ON--\._q/en tile air conditioner is off, it
can be set to automatically mrn on in half
an horn" to 24 hours at its previous setting.
Each touch will set the time in half horns
up to l0 and then in horns up to 24.
To cancel (CI,) tile On Timer press tile
ONpad again.
OFF--_A]mn tile air conditioner is on, it
can be set to automatically tm'n off in half
an hour t() 94 h()ms. Each touch will set
tile time in half hom_ up to l 0 and then
in hom_ up to 24.
To cancel (CI,) the OffTimer press the
OEEpadagain.
To cancel tile time_; press tile ONor OFF
pads/mtil tile display time disappears.
O SLEEP
Press to set tile air conditioner to run for
S hom_ before it automatically returns to
the previous setting.
X&]mn the sleep timer is set, the set
temperature will automatically increase
2°F atter tile second horn" then l °F each
hour over tile next two hotllS.
To cancel tile sleep mode, press tile MODE
pad or tile SLEEPpada second time.
O RemoteControlSignal Receiver
4
Remote Control
[] To ensure proper operation, aim tile
remote control at tile signal receixer
on tile air conditioner
[] Tile remote control si_mal has a range of
up t() 21 feet.
[] Make sm'e nothing is between tile air
conditioner and tile remote control that
could block the signal.
[] Make sure batteries are fl'esh and installed
con'ecflx_see tile Care and gleaning section.
wnnN.GEAppliances.com
COOLMODE
RemoteControl
l. Px_ssCOOLpad.
2.P*_ssLOW.MEDor HIpads to set desired fire speed.
3.Px_ssdieINCREASEA/DECREASETpadstoset the
desix_d temperature 60°Fto 85°F ill l°Fincrements.
ControlPanel
l. Pless die MODEpad until tile COOLindicator lig]lt is
lit and the LOW.MEDor Hlin(ficator light is lit for
dm desil_d t_m speed.
2. Pl_ss the INCREASE&/DECREASET pads to set the
desil_d temperature 60°F to 85°F ill l °F increments.
A them/osmt is used to maintain tile roon/
tempenmlre. Tile con/pressor will (3cle on and off
to keep tile room at tile set level of comfi)rt. Set file
thermostat at a lo_r number and tim indoor air will
become coolel; Set tile thermostat at a higJmr nm-nber
and tile indoor air will become _mnel:
NOTE:ff theair conditioner is off andis thenturned on
while set toCOOL,it will take approximately3minutes for
the compressortostart and cooling tobegin.
CoolingDescriptions
ForNormalCooling--Selectthe COOLmode and
HIGHor MEDtim with a middle set temperature.
ForMaximumCooling--Select tile COOLmode
and HIGHfire with a lower set temperaU/l>.
ForQuieter&NighttimeCoolino--Selecttile COOLmode
and LOWfimwifl_a middle set temperature.
NOTE:If youswitchfroma COOLsettingtoOFFor to
afansetting,waitatleast3minutesbeforeswitchingback
toaCOOLsetting.
Fan Switch
Tile tim switch is located behind tile ti'ont grille on the
control box. Access through a hole ill control box.
_A]mn set at CYCLE((]o_n) tile thn e_cles on and oti_
When set at CONT(continuous, up) tile tim runs all tile
time providing a mol_ balanced mmperaull_. The unit
is shipped ill the cONrsetting.
FAN MODE
Use tile FANmode to pro\ide _drcirculation and
filtering without cooling. Since fire only settings do not
provide cooling, a temt)emture setting will not be
displa}ed.
RemoteControl
Pl>ss FANpad. Press LOW,MEDor HI pads to set
desil_d Jim speed.
ControlPanel
Pless die MODEpad until tile FANindicator light is lit
and tile LOW, MEOor HIin(ficator light is lit fi)r the
desil>d Jim speed.
Vent Control
Tile vent control is located behind tile ti'ont grille on
tile right side of tile air (fischarge area. "_lmn set at
CLOSE,only tile air inside file room will be circulated
and conditioned. When set at OPEN, some inside air is
exhausted outside.
To opell or close tile vent:
1. Remove the ti'ont grille.
2. Remove tile vent card scions.
3. Remove vent card, turn it o\'er and replace it b}
locating rear hole ill card over locating pin inside air
discharge and reattaching scre_ at fi'ont.
Theunitleavesthefactoryset attheCLOSEposition.
._Locating hole
Screwhole "_.
OPENposition
(Meshendtowardback)
Screwho
CLOSEposition
(Meshendtowardfront)
A# Direction
Horiz(mt_fl lomers
(m tim front grille let
you control tile _dr
(lirecti(m up and
doPvI/.
Remo\'e tile fl'ont
,grille to a(!just file
vertical louvers
side-to_ide to
dilect the air
left or fight.
Aboutthecontrolsonthe air conditionermmodels with touchpads.
Auxiliary Controls- TemperatureLimiting
To reach the auxiliary controls remove the fl'ont
g_ille. Access them through the small rectangular
opening above the control panel.
Temperature limiting can reduce energy
costs by limiting the lowest temperature that
can be set for cooling. Temperature limiting is
controlled bv switches 1-3 of a u_lia_w controls.
TL1(C){Temp.Limit1 Cod)
TL2(C){Temp.Limit2 Cool)
TL3(C}{Temp.Limit3 Cool}
UP
-- Nofunction(reserved
for futureuse)
DOWN
Temperaturelimiting during COOLmode
(all temperatures shown in °F)
UP DOWN Minimum Maximum
NONE 1,2,3 60° 85°
1 2,3 64° 85°
1,2 3 66° 85°
2 1,3 68° 85°
2,3 1 70° 85°
1,2,3 NONE 72° 85°
1,3 2 74° 85°
3 1,2 76° 85°
@
Aboutthecontrolsontheair conditioner--modelswith controlknobs.
LOW
FAN
OFF • HIGH
r_j_l _ FAN
LOW_ _ I I I _ ALOW
HEAT'!I I yCOOL
HIGH_ll I I Ill HIGH
HEAT--_" COOL
OFF
LOWa _ a LOW
FAN_COOL
HIGHm • I I •_ HIGH
FAN w_w COOL
i
S
/
/
8
MODECONTROL TEMPCONTROL
0
o Mode Control
HIGHCOOLand LOWCOOLl)r°'_ide cooling
with different tim speeds,
HIGHHEATand LOWHEATprovide heating
with different Lm speeds,
LOWFAN or HIGH FAN provides air
circulation and filtering without cooling
or heating.
NOTE:If youmovetheswitchfromacoolorheat
settingtoOFFortoafansettingwaitat least
3 minutesbeforeswitchingbacktoa coolorheat
setting.A.?-minutedelayisautomat/ca//yprovided
ontheHeat/CoolandHeatPumpmodels.
Cooling/HeatingDescriptions
ForNormal CoolingorHeating--Select
HIGHCOOLor HIGHHEATwith the
thermostat at mid point.
ForMaximum Cooling--Select HIGHCOOL
with the therlnostat at n/axinmln cool.
o TempControl
The telnp control is used to inaii_tain the
room telnperature. The compressor will
cycle on and off to keeI) the room at the
same level of coi/lfi)i_t. _*\]/en vou turn
the knob to COOLER(blue) the indoor air
will become cooler. Turn the knob to
WARMER (red) and the indoor air will
be('oi/l e W}llI/l el:
Heat PumpModels
When the outdoor temperature is lower
than 25°E, heat is provided by the electric
heater in the air conditioner instead ot by
the heat pump.
NOTE"Theelectricresistanceheaterin the115-volt
heatpumpmodeloperatesduringdefrostwhenthe
outdoorcoiltemperaturessbelow36°£It/2not
intendedtoprovidefurlheatcapability
For Maximum Heating_Select HIGH HEAT
with the thermostat at nlaxinlulll heat.
For Quieter & Nighttime Cooling---.Select
LOWCOOLwith the thern_ostat at mid
point.
www.GEAppliances.com
Fan Switch
To reach tile tim switch (es) remove tile
fl'ont grille.
OnHeat/Cool and Heat Pumpmodels, tile tim switch
leveI_ are located in holes accessed through tile
control box. Tile top switch is fin _COOLsettings
and tile bottom sMtch is fin" HEATsettings.
Use a small screwdriver to change tile setting.
Tile trait is shii)ped ti'om tile thctory set in tile
CONTsetting tot COOLand in tile cgCtfsetting
tot HEAT
Coolonly models have a rocker switch on tile
front of tile control box.
_._qaen set at CYCLE(down) tile tim cycles on and
off when cooling. When set at CONT (continuous,
up) tile tim runs all tile time, providing a more
balanced temperature. Tile trait is shiI)ped in
tile CONTsetting.
Temperature Limiting
Limiting tile maMmum and minimum settings
prevents useI_ ti'om ttwning tile control to tile
extreme heat or cool positions.
Tile mmnal range of tile temp control is
approximately 60°F to 85°E Tile control range
may be narrowed by the use of tile temperattu'e
limiting screws located behind tile control panel.
@
@ @
@
Limits
heat cool
temp temp
Eachposition equals approximately 3°E
Vent Control
Tile vent control is located behind tile ti'ont
grille on tile fight side of tile air discharge area.
X,_qlell set at CLOSE,onl} tile air inside tile rooln
will be circulated aim conditiolaed. When set at
OPEN, some inside air is exhausted outside.
To oi)ell or close tile vellt:
1. Remove tile front giille.
2. Ren/ove tile vent card scre_:
3. Remove vent card, turla it over and replace
it by locating rear hole in card over locating
pin inside air discharge aim reattaching
screw at Ji'Ollt.
TheunitleavesthefactorysetattheCLOSEposition.
_hole
OPENposition
(Meshendtowardback)
Screwhc
CLOSEposition
(Meshendtowardfront)
A# Direction
HolJzoHt _] ]olwers
let voll coH[i'o] [])e
air direcd(m iq:_
_tm?(] dow]L
Remove tile [_'o_1[
grille t _ a(!jl_st tl_e
vertical ]om'ers
side-to-side to
di rect tile ai r ]eft
or right,
Careand cleaningoftheair conditioner..
Grille and Case
Turn the air conditioner off and remoxe the To clean, use water and a mild detergent.
plug, ti'on_ the wall outlet before cleaning, Do not use bleach or abrasixes.
OutdoorCoils
The coils on the outdoor side ()t the air
conditioner should be checked regularly.
If they are clogged with dirt or soot they may be
professionally steam cleaned, a service available
through yore" GE se_Mce outlet.
Front Grille
The fl'ont grille can be removed tot more
thorough cleaning or to make the model and
serial n/lillbeYs accessible.
Toremove:
1. Pull the filter out.
2. Remove the two grille scre_vs.
Onsomemodels
3 Pull the r,rille out fl'om the bottom and lift up
fl'om the tabs on the top of the case.
Grille
10
Onsomemodels
To replace:
Hook the tabs on the fl'ont grille even with the
tabs on the case and snap into place,
Replace the scrmvs and filtex;
www.GEAppliances.com
Tomaintain optimum performance, clean the filter at least every 30 days.
Air Filter
Toremove the air filter, on uther models:
Pull it down.
Dirty filte_Needs cleanhTg Clogged filter Greatly
reduces coolhTg heating
and airflow.
Turn the air conditioner off before cleaning.
The most important thing you can do to
maintain the air conditioner is to clean the filter
at least ex'e_T 30 days. A clogged filter reduces
cooling, heating and air flow.
Keepingthe air filler clean will:
• Decrease cost of operation.
• Save energ 7.
• Prevent clogged heat exchanger coils.
• ]_.e(luce the risk of premature component
fifilure.
Tocleantheair filters:
• Vacumn off the heavv soil.
Toreplace the air filter."
Replace the clean filter by lmshing it back
into place.
• Rm] water through the filte_5.
• D_T thoroughly befiwe replacing.
Toremove the air filter, on some models:
Careflflly pull the tab forward, up and out.
CAUTION:oo.utoperatetheair
conditioner without the filter in place, ff a filter
becomes torn or damaged # should be replaced
immediately.
Operating without the filter in place or with a
damaged filter will allow dirt and (hlst to reach
the indoor coil and reduce the cooling, heating,
ai_low and efficiency ot the unit.
Replacement filtet_ are ax filable from your
salesl)e_on, (;E dealer, (;E Service and Pints
Center or authorized Customer Care _' servicers.
How to Insert the Batteries
] Remove the battery cover b) s]idim_g it
accordh)g to the _]']'()_r directi(m.
] In)serf i)ex{ rbnttel:ies makim)g sm'e that the
(+) amid (-) of batter_ are im_stai]ed correct]'_.
] Reattach d_e cover b} s]idim_g it back
im)[O [)Ogi[iOi).
NOTES:
[] (Ise 2 AAA (1.5 volt) batteries. Do m_ot I_se
rech a rgeab] e bat teri es.
[] Remove the bntteries {_'()m the remote col)fro]
if the s}:stem is m_ot goh_g to be I*sed for a ]om_g
[]me.
/z
Installation
Instructions
Air Conditioner
I _7 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: www.GEAppliances.com I
BEFORE YOU BEGIN
Read these instructions completely and
carefully.
• IMPORTANT - Savetheseinstructions
for local inspector's use.
• IMPORTANT -Observeallgoverning
codes and ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumer.
• Note to Consumer - Keep these instructions for
future reference.
• Skill level - Installation of this appliance requires
basic mechanical skills.
• Completion time- Approximately 1 hour
• We recommend that two people install this
product.
• Proper installation is the responsibility of the
installer.
• Product failure due to improper installation
is not covered under the Warranty.
ELECTRICAL
Some modeB require a 115/120-volt a.c.,
60 Hz grounded outbt protected with a
15-amp time deby fuse or circuit breaker.
The 3-prong grounding plug minimizes the possibility
of electric shock hazar& if the wall outlet you plan to
use is only a 2-prong outlet, it is your responsibility
to have it replaced with a properly grounded 3-prong
wall outlet.
Some models require 230/208-volt a.c,,
protected with a time delay fuse or circuit
breaker, These models should be installed
on their own single branch circuit for best
performance and to prevent overloading
house or apartment wiring circuits, which
could cause a possible fire hazard from
overheating wires.
CAUTION:
Do not, under any circumstances, cut or remove
the third (ground) prong from the power cord.
Do not change the plug on the power cord
of this air conditioner.
Aluminum house wiring may present special
problems--consult a qualified electrician.
IMPORTANT!
GE strongly recommends the removal of the old
wall case and the installation of a new GE Wall
Case. If you decide to keep the existing wall case,
you may need a kit to ensure proper performance.
If you DO NOT use a kit, you run the risk of poor
performance or product failure. This is not covered
under the terms of the GE warranty.
J-MODEL QUALIFYING QUESTIONS
J-model air conditioners may fit in existing wall cases.
However, they often need a kit to properly adapt the
case to the GE air conditioner. Answer these questions
and see the chart on the next page for the proper kit.
r_ What brand air conditioner will you be replacing?
What are the dimensions of the wall case
[] currently in use?
[] What isthe model number of the chassis
currently in use? What isthe model (or Type)
number of the wall case currently in use?
Frequently, the J-model adapter kit will apply to
another brand model "series" or specific vintage.
In these cases, you need the chassis model
number and/or the wall case or "type" number
to confirm the use of the correct adapter kit.
[] What type of outdoor grille isused with the
current wall case?
There may be an architectural grille attached to
a wall case to enhance the exterior appearance
of the building. Custom grilles may be used with
J-model wall cases provided a J-model adapter
kit is also used to ensure proper airflow.
12
mnstaJiation mnsttuctions
Read these instructions completely and carefully.
Power cord may include a current interrupter
device. A test and reset button is provided on the
plug case. The device should be tested on a
periodic basis by first pressing the TEST button
and then the RESET button. If the TEST button
does not trip or if the RESET button will not stay
engaged, discontinue use of the air conditioner
and contact a qualified service technician.
TOOLS YOU MAY NEED
Hand or Saber Saw
Pencil
Scissors or knife
Adjustable Wrench _ Level
Ruler or Tape
Measure
GE KiT NUMBERS
USE GE
KIT NUMBER: FOR: DESCRIPTION:
RAK56A100 GERAB13,14 & 15 Fitsall GEwall cases26'_/Vx 18"Hx 24"D
(ACLB& RCLChassis)
RAK1072 Hotpoint ACXB10& 11 Adapts an older Hotpoint wall caseto a "J"
(ACTBChassis) model chassis. Fits Hotpoint wall cases
25¾"W x 167X'Hx 18%"D
RAK1082 Whirlpool Type23W Adapts Whirlpool wall case to a "J"
Wall Case model chassis.FitsWhirlpool wall
cases257X_/Vx 16W'H x 23W'D
RAK1102 GERAB30 Adapts GEwall case to a "J" model chassis.
("F" models) Fitsthe RAB30 wall case 26'!/V x 18"H x 24"D
RAK123A64 FeddersWall Case"A" Adapts Fedderswall case to a "J" model chassis.
FitsFedderswall cases27"W x 163A"Hx 163A"D
RAK126 Westinghouse Wall Case Adapts Westinghouse wall case to a "J"
(Type2626D73H01) model chassis. FitsWestinghouse wall
cases257X'W x 157A6"Hx 16"D
RAB46, 47 & 48 Usethese kits for all Standardwall case for "J" model chassis.
other brands not listed. RAG13stamped aluminum exterior grille
included. Removethe existing case
and replace.
RAK690 RAB36,37, 38, 46, 47 or 48 If you attach acustom architectural outdoor
(J-Chassis) grille, usethis kit to ensureproper airflow.
RAG13 RAB36,37, 38, 46, 47 or 48 Standard aluminum exterior grille (included with RAB46,47,and 48 wall
(J-Chassis) cases)
RAG14E RAB36,37, 38, 46, 47 or 48 Architectural Iouvered exterior grille
(J-Chassis)
13
Installation Instructions
INSTALLING A J-MODEL IN AN EXISTING WALL CASE
Read these instructions completely and carefully.
[] REMOVE LOCKING PLATE ON
FRONT LEFT SIDE
Locking
plate
Remove
screw
/
[] REMOVE THREE SHIPPING PADS
INSIDE AIR CONDITIONER NEXT TO
COMPRESSOR
Remove
shipping
pads
[] REINSTALL LOCKING PLATE WITH
TAB BEHIND WALL CASE FLANGE.
TIGHTEN SCREW
[] ATTACH POWER CORD TO BASE
PAN WITH CLAMP
pan
cord
P
[] WHEN WALL OUTLET IS TO LEFT,
EXTEND CORD UNDER UNIT AND
HOLD IT IN PLACE WITH CLAMP
Power
p cord
[] CAREFULLY SLIDE AIR
CONDITIONER BACK INTO CASE
Make sure that the tubing on the unit does
not touch the wall case and that the case
installation is secure.
[] ATTACH FRONT GRILLE
An opening for the power cord is on the
bottom of the front grille.
mnstaJiation mnstructions
INSTALLING THROUGH THE WALL
Read these instructions completely and carefully.
[] PREPARE OPENING IN WALL
Make certain a wall receptacle is
available close to the hole location or make
arrangements to install a receptacle.
The cord length for the 115-volt models is 72"
to the right and 47" to the left.
For the 230/208-volt models the cord length is
65" to the right and 39" to the left.
[] SUPPORT REQUIREMENTS FOR
AIR CONDITIONER
The air conditioner wall case may be installed
with 1/4" min. extension out from the inside
wall or with 1/4" min. extension out from the
outside wall.
The finished sides of the opening should be
structural wall members.
Lintel - Use a lintel in brick veneer and brick
and block types of wall to support the bricks
or blocks above the opening. Do not allow the
wall case to be used in lieu of a lintel.
Flashing- Install flashing (drip rail) as shown
to prevent water from dripping inside the wall
and down the outside of the building.
Lintel angle
(if required) _ Plaster
Caulking _ line
(on all 4_
sides on the Trim
outside of molding
the case) (if desired)
Room side
Flashing
(drip rail)
i
1/4" min. extension J
inside the wall from
the trim molding
[] SUPPORT REQUIREMENTS FOR
AIR CONDITIONER
Mortar between the case and the brick all
around the case may be undercut at about 45 °
for improved caulking.
Inside
Top of case
Caulking
Outside
mortar
15
JnstaJJation instructions
WINDOW INSTALLATION--OPTIONAL
FOR MODELS AJES06LSB, AJES08ASB, AJES10DSB and AJHS08ASB
Read these instructions completely and carefully.
Sill support
bracket (2) x_k
2 angles_
(left and
right hand)
° B
Right
side
d)
-(:
¢0
I A •
J
'_Left side
Filler
Panels m
60
Cut panels _
and
discard o
center
piece m
u i o
L I
B I
_-_ Case side
gasket (2)
F inyl window
gasket
Foam top
_ _ window gasket
Spring \ Case top gasket
clip (4) \
_Bottom window gasket
Window
_ locking
bracket
Air conditioner
Type A (9)
'i
Type B (2)
Type C (painted) (6)
Type D (2)
Type E (4)
Support bracket hardware
4'
Spacer (2)
Lock nut (2)
&
Adjusting bolt (2)
@
Large washer (2)
[] WINDOW REQUIREMENTS
• These instructions are for a standard double-hung
window. You will need to modify them for other
types of windows.
• The air conditioner can be installed without the
accordion panels if needed to fit in a narrow
window. See the window opening dimensions
to the right.
• All supporting parts must be secured to firm wood,
masonry or metal.
• The electrical outlet must be within reach of the
power cord.
, 17minII
_ (Wit h31'il_°r43anels)_'-1
26 Y4" min.
(Without filler panels)
Window opening dimensions are for a
standard double-hung window.
16
Installation Instructions
[]STORM WINDOW REQUIREMENTS
A storm window frame will not allow the air
conditioner to tilt towards the outside and will
keep it from draining properly. To adjust for this,
attach a piece of wood to the stool.
1/2" Mgher _ ,_./Wood
than A
, ame oi¢
Storm " _ II
window II II
frame 1_ II
WOOD PIECES:
WIDTH: 2"
LENGTH: Long enough to fit inside the window
frame.
THICKNESS: To determine the thickness, place a
piece of wood on the stool to make it 1/2" higher
than the top of the storm window frame.
Attach securely with nails or screws provided by
the installer.
131REMOVEAIR CONDITIONER FROM CASE
[] Remove the front grille. See the Care and
Cleaning section.
[] Find the locking plate located on the front
left side.
[] Remove the screw and the locking plate to
Locking
plate
screw
unlock the air conditioner.
[]
Remove and discard the shipping screw
on the back of the air conditioner to allow
removal of the air conditioner from the
case.
[]
Remove
screw
Pull the bottom corners of the air
conditioner and slide it out of the case.
[] Remove the three shipping pads inside the air
conditioner next to the compressor.
Remove
shipping
pads
[] Remove the rear grille that is taped to the back
of the case. Remove the packet of screws taped
to the back of the grille. While holding the grille
at a 45°angle, insert it into the clips at the top of
the case and push the bottom in. Keep slight
upward pressure on the grille until it fits flush
with the bottom of the case.
If attaching the grille
from the outside of
the case use the 2
long screws.
If attaching the grille
on the inside of the
case use the 2 short
screws.
Clips
Insert the 2 long screws on
the outside
_illllllllllllllllllllllllllllllllllllllllllll_i
_/llllllllllllllllllllllllllllllllllllllllllll/Jl
_/11111111111111111111111111111111111111111111/H
Insert the 2 short screws
on the inside
17
mnstaJiation mnstructions
WINDOW INSTALLATION--OPTIONAL (cont.)
[] PREPAREWINDOW
[] Mark the centerline of the stool. Measure
from the centerline 1378" on both sides for
the panel cuts.
[] Measure 1278" from the centerline on both sides
for the sill support brackets.
Centerline
,stoo,
_._ 133/_,,._,_
Sill
Centerline
[] INSTALL SILL SUPPORTS
[] Assemble the sill supports. Do not fully
tighten the spacer mounting screws at this
time.
Type B
Type E
suppo_
Spacer mounting
screws Type (A)
Spacer
[] Turn the bolts and tighten the lock nuts to make
the sill supports level or tilt down 1/8" to the
outside. Line up the "V" notch with 1278" marks.
Drill pilot holes and attach the sill supports.
Average sill
Sill s_ _/_ Spacer
Narrow sill
Adjusting bolt-_
Large washer_(;_)
(For use withwood
sills)
Offset sill (such as brick or stone)
[] Before attaching the sill supports, place
them on the window stool. Select the spacer
position that will place the spacer near the
outermost point on the sill. Tighten the
spacer mounting screws.
Screws are in position
Sill
support
"V" notch
NOTES:
• On narrow sills, there may not be enough room to
use the lock nut.
• A deep offset sill may require a longer adjusting
bolt than the standard hex head bolt provided.
• On wood sills use the large washer between the
bolt head and the sill. This prevents the bolt fro m
digging into the wood.
Sill
18
JnstaJJation instructions
[] MEASURE, CUT AND INSTALL
FILLER PANELS
[] Measure from the edge of the panel marks
(see Prepare the Window) to the inside of
the window track on each side. (A and B)
Sill
Window track _,_1k
J A _'_ Width of thealr _ B
conditioner
Left side (panel marks) Right side
[] Mark the A and B measurements on each
side of the filler panel board. Cut the panels
and discard the center piece. Note position
of the notches.
° B A °
Right Left
side side
Filler
Panels °
c Cut
o panels o
'_ and
discard _"
center
o _ piece , _ °
[] Put together the panel assemblies. Remove
the paper backing from the case side gasket
and attach it to the angle. Push a pencil point
through the gaskets to locate the holes in
the angles.
Gasket--_ _j¢/_ Angle
Angle
Gasket ___Panel
Tab J
Type C
(painted
screws)
[] Install the panels in the window. Place the spring
clips 3" from the top and the bottom. Squeeze
and push the clips to fit in the window track and
the tab into the sill support.
J13"
Hook the tab into
the sill support
19
Installation Instructions
WINDOW INSTALLATION--OPTIONAL (cont.)
[] INSTALL CASE IN WINDOW
[] Peel off the backing from the bottom
window gasket.
FB] Place the gasket on the stool and over the
brackets, even with the rear edge, sticky
side down.
L J
i
Bottom window gasket
[] Carefully slide the empty case into the
window until the holes in the case line up
with the holes in the panel angles.
Case holes
!l I!
[] With the window closed, mark where the
window sash meets the case.
[] Peel off the backing from the case top gasket.
[] Hold on to the case, open the window, and
place the gasket along the mark on the case.
Put the gasket
on top of the
case where
the window
will close.
[] Place the vinyl window gasket over the case top
gasket. Insert the panel tabs through the slits in
the gasket. Cut the gasket on each side to the
width of the window.
NOTES:
• The case should have a 1/8" minimum tilt
toward the outside.
• Be sure the seal gasket and panel gaskets
remain in position and do not roll with the
case.
[] Lower the window so it fits behind the panel
tabs. Insert the 4 type A screws through the
holes in the case and into the panel angles,
2 on each side.
tabs
Case
screws
[]
tab
Vinyl window
gasket
Close the window tightly on the vinyl gasket.
Bend the gasket forward to expose the panel
tabs. Drill pilot holes into the window sash.
/_Attach the panel tab
/to the window on
II _each side with a type
I [L__/ D screw.
i i l _w
2O
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
