Honeywell HZ221 TrueZONE Control Panel Installation guide

Brand: Honeywell

Model: HZ221 TrueZONE Control Panel

Type: Installation guide

Zone Panel Professional Installation Guide

HZ221 TrueZONE

69-2200-01

firealarmresources.com

Installation Guide

 69-2200—0

TABLE OF CONTENTS

Read and save these instructions.

Need Help?

For assistance with this product please visit http://yourhome.honeywell.com

or call Honeywell Zoning Hotline toll-free at 1-800-828-8367

® U.S. Registered Trademark.

Patents pending.

Specifications and Accessories ...................................................................................................1

Installation ......................................................................................................................................2

Wiring ..............................................................................................................................................3

Operation ........................................................................................................................................5

Warranty .........................................................................................................................................6

firealarmresources.com

HZ22 TrueZONE

 69-2200—0

SPECIFICATIONS AND ACCESSORIES

Input Ratings:

Voltage: 18-30 VAC 50/60 Hz transformer of 40 VA

or more.

Current Draw:

Zone Panel: 6.25 VA max.

All VA specifications at 24 VAC.

Wiring:

18–20-gauge solid (not stranded) wire.

Humidity Ratings:

5% to 90% RH non-condensing.

Temperature Ratings:

Shipping: -20° to 150°F (-29° to 66°C)

Operating: -40° to 165°F (-40° to 74°C)

Dimensions:

See below.

Emissions:

Complies with FCC Class B, part 15 requirements.

M24742A

8 (203)

8-1/8

(206)

1-55/64

(47)

HZ221 TrueZONE panel dimensions in in. (mm).

RECOMMENDED THERMOSTATS, DAMPERS, AND

ACCESSORIES

The following are suggested thermostats, dampers, and

accessories for use with the TrueZONE panel.

Table 1. Recommended Thermostats.

System Non-Programmable Programmable

Heat

Pump

TH3210D, TH5220D,

TH5320U

TH4210D, TH6220D,

TH8220U, TH8321U,

YTH9421C

Note: These thermostat models all have different four-

digit suffixes. All versions of the model numbers listed

above will work with the applications they're listed for.

Table 2. Recommended Dampers.

Type Honeywell

Damper

Round Rectangular

Zone Spring-open/

power-closed

ARD ZD

Zone Power-open/

power-closed

MARD/

RRD

For recommended

dampers call the

Honeywell Zoning

Hotline at

1-800-828-8367.

Bypass Static pres-

sure regulat-

ing damper

SPRD SPRD

Table 3. Maximum Dampers.*

Ambient Temp. Maximum Damper VA per Zone

100°F (38°C) 28.8

160°F (71°C) 16.8

* Use an SDCR (Slave Damper Control Relay) for addi-

tional dampers.

Maximum dampers per panel is limited by transformer

size.

Ensure transformer is large enough to power the panel

(6.25 VA) and dampers.

Table 4. Accessories.

Accessory Description

40 VA transformer* AT140A1042*

75 VA transformer AT175A1008

Discharge Air

Temperature Sensor

(DATS)*

DATS C7735A1000*

SDCR Slave Damper Control Relay

* Included in HZ221K kit.

firealarmresources.com

Installation Guide

69-2200—0 2

 69-2200—0

INSTALLATION

Mount the HZ221 TrueZONE

panel near the HVAC equip-

ment; locate it on a wall,

stud, roof truss, or cold-air

return.

NOTE: The HZ221

TrueZONE panel can be

mounted in any orientation;

level it for appearance only.

DATS

M28164

SUPPLY

DUCT

RETURN

DUCT

BYPASS

DAMPER

ZONE PANEL

(DUCT MOUNT)

ZONE PANEL

(WALL MOUNT)

ARD

DAMPERS

DATS

(ALTERNATE LOCATION)

Separate the zone panel cover from the base, and use the base as a template to drill mounting holes.

Attach the base to the wall, stud, roof truss, or duct with appropriate screws (not included).

Use two screws for attaching to a stud or roof truss, or

four screws for duct or drywall/plaster installations.

M24803

firealarmresources.com

69-2200—0 2

HZ22 TrueZONE

 69-2200—0

WIRING

Install thermostats using instructions provided with thermostats.

Connect thermostat to zone panel. To connect wire to the panel, strip

approximately 1/4 in. of insulation and push wire into terminal. To

release wire, press the button on top of the terminal. In retrofit applica-

tions, trim end of wire if not straight.

If the thermostat has separate E and Aux terminals, install a jumper

between the two terminals.

Wires can be run behind the panel, through

wire channels on the panel's sides, and

must be attached to a wiring anchor with a

cable tie.

M24743

ZONE 2 THERMOSTAT

M28234B

AUX

O/B

ZONE 2

DAMPER

THERMOSTAT

E/AUX

Wiring must comply with applicable codes, ordinances, and regulations.

Install dampers using instructions provided

with dampers. Connect dampers to zone

panel.

NOTE: Multiple dampers can be wired in

parallel.

M28235

ARD OR ZD DAMPER

SPRING-OPEN POWER-CLOSED

ZONE 2

DAMPER

ZONE 1

DAMPER

RRD OR MARD DAMPER

POWER-OPEN

POWER-CLOSED

M4 OPEN

M6 CLOSED

M1 COMMON

ARD OR ZD DAMPER SPRING-OPEN POWER-CLOSED

ZONE 2

DAMPER

CAUTION: Voltage Hazard.

Can cause electrical shock or equipment damage. Disconnect power before beginning installation.

Wire entire panel before applying transformer power.

Connect DATS as shown.

C7735A1000 M24804

DATS

SENSOR

firealarmresources.com

Installation Guide

69-2200—0 

 69-2200—0

The DS/BK terminal is used with a variable-speed fan.

Connect to the DS, BK, or ODD terminal on the furnace

equipment. When only one zone calls for heat, cool, or

fan, the DS/BK terminal operates the fan at low speed

to reduce airflow.

7Connect transformer as shown.

Connect equipment as shown.

WIRING

DEDICATED TRANSFORMER

M28237

POWER

(HOT)

M28236A

EQUIPMENT

E/Aux

DS/BK

AIR

HANDLER

FAN RELAY

AUX/EM HEAT

HEAT PUMP

24 VOLT TRANS.

C R

REVERSING

VALVE

M27339

E/Aux

DS/BK

AIR

HANDLER

FAN RELAY

AUX HEAT

HEAT PUMP

24 VOLT TRANS.

C R

REVERSING

VALVE

ZONE 2 THERMOSTAT

ARD OR ZD DAMPER

SPRING-OPEN

POWER-CLOSED

PURGE OVERRIDE

EQUIPMENT

M4 OPEN

M6 CLOSED

M1 COMMON

E/AUX

THERMOSTAT

AUX

O/B

RRD OR MARD DAMPER

POWER-OPEN

POWER-CLOSED

E/AUX

THERMOSTAT

ZONE 1

DAMPER

ZONE 2

DAMPER

DEDICATED

TRANSFORMER

(HOT)

C7735A1000

DATS

HEAT

COOL

FAN

PURGE

ZONE 1

ZONE 2

EM HEAT

EMERGENCY HEAT

POWER

SENSOR

The following diagram is an overall view of wiring for a heat pump system as depicted in steps 3–7.

firealarmresources.com

69-2200—0 

HZ22 TrueZONE

 69-2200—0

The HZ221 TrueZONE panel contains an LED display that communicates system and zone status. The LEDs indicate

the following information.

OPERATION

HZ221

HEAT

COOL

FAN

PURGE

ZONE 1

ZONE 2

EM HEAT

M28239A

LED display.

Table 5. LED Operation.

LED Description

HEAT Solid when in heat.

Blinking when DATS temperature exceeds 120°F

(49°C) and calling for heat pump only.

Blinking when DATS temperature exceeds 160°F

(71°C) and calling for heat pump and auxiliary

heat. At 150°F (66°C), auxiliary heat is disabled.

COOL Solid when in cool. Blinking when 45°F (7°C) DATS

low limit mode has been reached.

FAN Solid when in operation.

PURGE Solid when in purge (lasts 2 minutes at power-up

and after a call for heat or cool). Blinking when the

DATS sensor has failed, or the wires are shorted or

open. Will blink for 3 minutes at power-up if DATS

is not present.

ZONE 1, 2 Solid green when open or opening.

Solid red when closed or closing.

Blinking amber when there is a damper or thermo-

stat short circuit (circuit breaker trip).

EM HEAT Solid when in Em Heat mode.

HZ221

2 Zones, 2H/1C

LED Status

Heat LED Heating Mode

Flashing Heat LED High Limit

Cool LED Cooling Mode

Flashing Cool LED Low Limit

Purge LED Purge Mode

Flashing Purge LED Sensor Failure

Fan LED Fan On

Zone LEDs Green - Open

Red - Closed

Flashing - Short

Zone Names

Zone 1 _______________________

Zone 2 _______________________

Technical Support: 1-800-828-8367

Customer.Honeywell.com

Patents Pending

50031314-001 Rev. A

M28240A

Em Heat LED Em Heat Mode

Much of this information is also listed on the label on the

inside of the HZ221 cover.

When the zone panel cover is off, the EMERGENCY HEAT/PURGE OVERRIDE button

is visible.

When the panel is in Purge (at startup or after a call for heat/cool), pressing this but-

ton stops the Purge, which saves time during installation or troubleshooting.

All other times, pressing the button puts the zone panel into Em Heat mode so that

all calls for heat are handled by the auxiliary heat.

M24741A

HZ311

HEAT

COOL

FAN

PURGE

ZONE 1

ZONE 2

ZONE 3

ZONE 1

DAMPER THERMOSTAT

DATS

EQUIPMENTPOWERSENSOR ZONE 3

DAMPER

THERMOSTAT

ZONE 2

DAMPER THERMOSTAT

PURGE OVERRIDE

EMERGENCY HEAT

firealarmresources.com

Honeywell International Inc.

1985 Douglas Drive North

Golden Valley, MN 55422

customer.honeywell.com

Automation and Control Solutions

Honeywell Limited-Honeywell Limitée

35 Dynamic Drive

Toronto, Ontario M1V 4Z9

Printed in U.S.A. on recycled

paper containing at least 10%

post-consumer paper fibers.

® U.S. Registered Trademark.

Patents pending

69-2200—01 M.S. 04-08

WARRANTY

Honeywell warrants the products in this catalog (except those parts designated on Honeywell’s price lists as not covered by this warranty) to be free from defects due

to workmanship or materials, under normal use and service, for the following warranty periods. Honeywell VisionPRO®, Commercial VisionPROTM, FocusPRO®, PRO

4000, PRO 3000, LineVoltTM PRO, Digital RoundTM, and Modern RoundTM (T87K, N) Series Thermostats with a date code of 0501 or later: sixty (60) months from date of

installation. CommercialPRO, PRO 2000 and PRO 1000 thermostats: twenty-four (24) months from date of installation. All other Honeywell thermostats and thermo-

stats with a date code of 0452 or earlier: twelve (12) months from date of installation, unless specified otherwise. Honeywell Air Cleaners, Humidifiers, Ventilators,

Ultraviolet Treatment and Zoning Products with a date code of 0501 or later, excluding replacement maintenance parts: sixty (60) months from date of installation. All

other Honeywell indoor air quality and zoning products with a date code of 0452 or earlier: twenty-four (24) months from date of installation, unless specified other-

wise. Variable frequency drive devices (VFD) and accessories: new products for thirty-six (36) months and factory refurbished drives for twelve (12) months from date

of installation when start-up and commissioning is performed by Honeywell VFD Authorized and trained personnel. All VFD warranty return products must have prior

authorization (Form No. 87-0284) and be returned only to the VFD Service Center in Chattanooga, TN. MS, MN and Fact Acting 2-position Direct Coupled Actuators:

sixty (60) months from date of installation. The warranty period for all other products is twelve (12) months from date of installation.

If a product is defective due to workmanship or materials, is removed within the applicable warranty period, and is returned to Honeywell in accordance with the pro-

cedure described below, Honeywell will, at its option, either repair, replace or credit the customer for the purchase price of the product, in accordance with the proce-

dure described below. This warranty extends only to persons or organizations who purchase products in this catalog for resale.

The expressed warranty above constitutes the entire warranty of Honeywell with respect to the products in this catalog and IS IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL

HONEYWELL BE RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY NATURE WHATSOEVER.

firealarmresources.com