Denon AVR-5308CI(A) User guide

AV SURROUND RECEIVER

AVR-5308CI

Owner’s Manual

 GraphicalUserInterface

Use this manual in combination with the operating

guide displayed on the GUI screen.

GUI Menu Operation (vpage 25)

GUI Menu Map (vpage 26)

Language (vpage 44)

Remote Control Unit Operations (vpage 78)

n

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning ﬂash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufﬁcient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature

accompanying the appliance.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

SAFETY INSTRUCTIONS

1. Read Instructions – All the safety and operating instructions should be read

before the product is operated.

2. Retain Instructions – The safety and operating instructions should be

retained for future reference.

3. Heed Warnings – All warnings on the product and in the operating

instructions should be adhered to.

4. Follow Instructions – All operating and use instructions should be followed.

5. Cleaning – Unplug this product from the wall outlet before cleaning. Do not

use liquid cleaners or aerosol cleaners.

6. Attachments – Do not use attachments not recommended by the product

manufacturer as they may cause hazards.

7. Water and Moisture – Do not use this product near water – for example,

near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement;

or near a swimming pool; and the like.

8. Accessories – Do not place this product on an unstable cart, stand, tripod,

bracket, or table. The product may fall, causing serious injury to a child or

adult, and serious damage to the product. Use only with a cart, stand,

tripod, bracket, or table recommended by the manufacturer, or sold with the

product. Any mounting of the product should

follow the manufacturer’s instructions, and should

use a mounting accessory recommended by the

manufacturer.

9. A product and cart combination should be moved

with care. Quick stops, excessive force, and

uneven surfaces may cause the product and cart

combination to overturn.

10. Ventilation – Slots and openings in the cabinet are provided for ventilation

and to ensure reliable operation of the product and to protect it from

overheating, and these openings must not be blocked or covered. The

openings should never be blocked by placing the product on a bed, sofa,

rug, or other similar surface. This product should not be placed in a built-in

installation such as a bookcase or rack unless proper ventilation is provided

or the manufacturer’s instructions have been adhered to.

11. Power Sources – This product should be operated only from the type of

power source indicated on the marking label. If you are not sure of the type

of power supply to your home, consult your product dealer or local power

company. For products intended to operate from battery power, or other

sources, refer to the operating instructions.

12. Grounding or Polarization – This product may be equipped with a polarized

alternating-current line plug (a plug having one blade wider than the other).

This plug will ﬁt into the power outlet only one way. This is a safety feature.

If you are unable to insert the plug fully into the outlet, try reversing the

plug. If the plug should still fail to ﬁt, contact your electrician to replace your

obsolete outlet. Do not defeat the safety purpose of the polarized plug.

13. Power-Cord Protection – Power-supply cords should be routed so that they

are not likely to be walked on or pinched by items placed upon or against

them, paying particular attention to cords at plugs, convenience receptacles,

and the point where they exit from the product.

15. Outdoor Antenna Grounding – If an outside antenna or cable system is

connected to the product, be sure the antenna or cable system is grounded

so as to provide some protection against voltage surges and built-up static

charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides

information with regard to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna discharge unit, size

of grounding conductors, location of antenna-discharge unit, connection to

grounding electrodes, and requirements for the grounding electrode. See

Figure A.

16. Lightning – For added protection for this product during a lightning storm,

or when it is left unattended and unused for long periods of time, unplug it

from the wall outlet and disconnect the antenna or cable system. This will

prevent damage to the product due to lightning and power-line surges.

17. Power Lines – An outside antenna system should not be located in the

vicinity of overhead power lines or other electric light or power circuits, or

where it can fall into such power lines or circuits. When installing an outside

antenna system, extreme care should be taken to keep from touching such

power lines or circuits as contact with them might be fatal.

18. Overloading – Do not overload wall outlets, extension cords, or integral

convenience receptacles as this can result in a risk of ﬁre or electric shock.

19. Object and Liquid Entry – Never push objects of any kind into this product

through openings as they may touch dangerous voltage points or short-out

parts that could result in a ﬁre or electric shock. Never spill liquid of any kind

on the product.

20. Servicing – Do not attempt to service this product yourself as opening or

removing covers may expose you to dangerous voltage or other hazards.

Refer all servicing to qualiﬁed service personnel.

21. Damage Requiring Service – Unplug this product from the wall outlet

and refer servicing to qualiﬁed service personnel under the following

conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating

instructions as an improper adjustment of other controls may result in

damage and will often require extensive work by a qualiﬁed technician to

restore the product to its normal operation,

e) If the product has been dropped or damaged in any way, and

f) When the product exhibits a distinct change in performance – this

indicates a need for service.

22. Replacement Parts – When replacement parts are required, be sure the

service technician has used replacement parts speciﬁed by the manufacturer

or have the same characteristics as the original part. Unauthorized

substitutions may result in ﬁre, electric shock, or other hazards.

23. Safety Check – Upon completion of any service or repairs to this product,

ask the service technician to perform safety checks to determine that the

product is in proper operating condition.

24. Wall or Ceiling Mounting – The product should be mounted to a wall or

ceiling only as recommended by the manufacturer.

25. Heat – The product should be situated away from heat sources such as

radiators, heat registers, stoves, or other products (including ampliﬁers) that

produce heat.

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL

ELECTRICAL CODE

"/5&//"

-&"%*/

8*3&

(306/%

$-".1

&-&$53*$

4&37*$&

&26*1.&/5

"/5&//"

%*4$)"3(&6/*5

/&$4&$5*0/

(306/%*/($0/%6$5034

/&$4&$5*0/

(306/%$-".14

108&34&37*$&(306/%*/(

&-&$530%&4:45&.

/&$"351"35)

/&$/"5*0/"-&-&$53*$"-$0%&

I

• Avoid high temperatures.

Allow for sufﬁcient heat dispersion when

installed in a rack.

• Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur

sufﬁsante lors de l’installation sur une

étagère.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du

cordon.

• Keep the unit free from moisture, water,

and dust.

• Protéger l’appareil contre l’humidité, l’eau

et la poussière.

• Unplug the power cord when not using the

unit for long periods of time.

• Débrancher le cordon d’alimentation

lorsque l’appareil n’est pas utilisé pendant

de longues périodes.

* (For apparatuses with ventilation holes)

• Do not obstruct the ventilation holes.

• Ne pas obstruer les trous d’aération.

• Do not let foreign objects into the unit.

• Ne pas laisser des objets étrangers dans

l’appareil.

• Do not let insecticides, benzene, and

thinner come in contact with the unit.

• Ne pas mettre en contact des insecticides,

du benzène et un diluant avec l’appareil.

• Never disassemble or modify the unit in

any way.

• Ne jamais démonter ou modiﬁer l’appareil

d’une manière ou d’une autre.

n

NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION

II

FCC Information (For US customers)

1. COMPLIANCE INFORMATION

Product Name: AV Surround Receiver

Model Number: AVR-5308CI

This product contains FCC ID: BV2- MPGBR052.

This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

product may not cause harmful interference, and (2) this product must accept any interference received, including

interference that may cause undesired operation.

Denon Electronics (USA), LLC

100 Corporate Drive, Mahwah, NJ 07430-2041

Tel. 201-762-6500 (Main)

2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modiﬁcation not expressly approved by DENON may void your authority, granted by the FCC, to use the product.

3. CAUTION

• To comply with FCC RF exposure compliance requirement, separation distance of at least 20 cm must be

maintained between the antenna of this product and all persons.

• This product and its antenna must not be co-located or operating in conjunction with any other antenna or

transmitter.

4. NOTE

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation.

This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this product does cause harmful interference to radio or

television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the product into an outlet on a circuit different from that to which the receiver is connected.

• Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for

help.

IC Information (For Canadian customers)

1. PRODUCT

This product contains IC 6963A-MPGBR052.

This product complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:

(1) this product may not cause harmful interference, and (2) this product must accept any interference received,

including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

APPAREIL

Cet appareil contiens IC 6963A- MPGBR052.

Cet appareil est conforme à la norme CNR-210 du Canada. L

’utilisation de ce dispositif est autorisée seulement

aux deux conditions suivantes : (1) il ne doit pas produire de brouillage, et (2) l’utilisateur du dispositif doit être

prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le

fonctionnement du dispositif.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

2. CAUTION

To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the

equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication.

ATTENTION

Aﬁn de réduire le risque d’interférence aux autres utilisateurs, il faut choisir le type d’antenne et son gain de façon à

ce que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne soit pas supérieure au niveau requis pour l’obtention

d’une communication satisfaisante.



Accessories ·····················································································3

Cautions on Handling ·····································································3

Cautions on Installation ································································· 3

About the Remote Control Unit ···················································· 3

Inserting the Batteries ·······························································3, 4

Operating Range of the Remote Control Unit ································4

Part Names and Functions ····························································4

Front Panel ·················································································4, 5

Display ···························································································5

Rear Panel ······················································································6

Remote Control Unit ······································································7

Getting Started

Preparations ····················································································8

Cables Used for Connections ························································8

Video Conversion Function ····························································9

Speaker Installation ·····································································10

Speaker Layout ············································································10

Speaker Connections ·····························································10, 11

Connecting Equipment with HDMI connectors ·························12

Connecting the Monitor ·······························································13

Connecting the Playback Components ······································ 13

DVD Player ···················································································13

Record Player ···············································································14

CD Player ·····················································································14

iPod

®

····························································································14

TV/CABLE Tuner ··········································································15

Satellite Receiver ·········································································15

Connecting the Recording Components ····································16

Digital Video Recorder ·································································16

Video Cassette Recorder ·····························································17

CD Recorder / MD Recorder / Tape Deck ····································17

Connections to Other Devices ·····················································18

Components Equipped with a DENON LINK connector ·············· 18

Video Camera / Game Console ····················································18

Component with Multi-channel Output connectors ·····················18

External Power Ampliﬁer ·····························································19

USB Port ······················································································19

XM Connector ··············································································20

Antenna terminals ·······································································21

Network Audio ·············································································22

Multi Zone ····················································································23

External Controller ·······································································24

Connecting the Power Cord ························································ 24

Once Connections are Completed ·············································· 24

Connections

Preparations ··················································································27

Auto Setup ····················································································27

a Auto Setup ········································································ 27, 28

Error Messages·······································································29

s Option ·····················································································29

d Parameter Check ···································································· 29

Auto Setup

Source Select

Contents

Surround Mode

Example of the Display of the GUI Mark at a Title ···················· 25

Example of Display of Default Values ········································25

Examples of GUI Screen Displays ··············································· 25

Example: Browse Menu (Top Menu) ···········································25

Example: Menus with Illustrations (Auto Setup) ··························25

Cursor Position Display ································································25

Operations ·····················································································25

GUI Menu Map ··············································································26

GUI Menu Operations

Speaker Setup ··············································································30

a Speaker Conﬁguration·····························································30

s Subwoofer Setup ···································································· 30

d Distance ·················································································· 31

f Channel Level ········································································· 31

g Crossover Frequency ························································ 31, 32

h THX Audio Setup·····································································32

j Surround Speaker ··································································· 32

HDMI Setup ··················································································· 33

a Color Space ·············································································33

s RGB Range ············································································· 33

d Auto Lip Sync ··········································································33

f Audio ·······················································································33

g Monitor Out ············································································ 33

h HDMI Control ··········································································33

Audio Setup ·················································································· 34

a EXT. IN Setup··········································································34

s 2ch Direct/Stereo ···································································· 34

d Downmix Option ·····································································34

f Auto Surround Mode ······························································ 34

g Manual EQ ··············································································35

Network Setup ·············································································35

a Network Setup ································································35 ~ 38

s Other ·······················································································38

d Network Information ·······························································38

Zone Setup ····················································································39

a ZONE2 ···················································································· 39

s ZONE3 ···················································································· 39

d OSD ························································································ 39

Option Setup ·················································································39

a Amp Assign·············································································40

s Volume Control ·······································································40

Manual Setup

d Source Delete ·········································································40

f GUI ··························································································40

g Quick Select Name ·································································40

h Trigger Out 1 ···········································································41

j Trigger Out 2 ···········································································41

k Trigger Out 3 ···········································································41

l Trigger Out 4 ···········································································41

A0 Transducer Setup ····································································41

A1 Digital Out ··············································································· 41

A2 Remote ID···············································································41

A3 2Way Remote ········································································· 41

A4 Dimmer ··················································································· 42

A5 Setup Lock ·············································································· 42

A6 Maintenance Mode ·································································42

A7 Firmware Update ····································································42

A8 Add New Feature ····································································42

Language ·······················································································43

Input Source Selection ·································································43

Settings Related to Playing Input Sources ································ 44

a Play ························································································· 44

s Auto Preset ············································································· 44

d Preset Skip ··············································································44

f Preset Name ··········································································· 44

g Video ······················································································· 45

h Input Mode ······································································· 45, 46

j Rename···················································································46

k Source Level ···········································································46

l Playback Mode (iPod)······························································46

A0 Assign ···············································································46, 47

A1 Playback Mode········································································47

A2 Still Picture ·············································································· 47

A3 Antenna Aiming ······································································ 47

HOME THX CINEMA ····································································· 48

Surround Playback of 2-channel Sources ·····································48

Playing Multi-channel Sources (Dolby Digital, DTS, etc.) ············· 48

Standard Playback ········································································48

Surround Playback of 2-channel Sources ·····································48

Playing Multi-channel Sources (Dolby Digital, DTS, etc.) ············· 49

Dolby Headphone ········································································49

DSP Simulation Playback ····························································49

Stereo Playback ············································································49

Direct Playback ············································································· 50

Playback in the PURE DIRECT Mode ···········································50



Multi-Zone Settings with the Amp Assign Function ········85 ~ 88

Multi-Zone Settings and Operations ··········································89

Multi-Zone Operations ································································· 90

Turning the Power On and Off ·····················································90

Selecting the Input Source ···························································90

Adjusting the Volume ···································································90

Turning off the Sound Temporarily ··············································90

Amp Assign / Multi-Zone Connections and Operations

Troubleshooting ······························································ 106 ~ 110

Speciﬁcations ····································································· 110, 111

Other Information ······························································91 ~ 105

List of preset codes ··········································· End of this manual

Audio ·····························································································50

a Surround Parameters ······················································50 ~ 52

s Tone ························································································ 52

d Room EQ ················································································ 53

f Dynamic EQ ············································································ 53

g RESTORER ············································································· 53

h Night Mode ············································································· 53

j Audio Delay ·············································································54

Picture Adjust ···············································································54

a Contrast ·················································································· 54

s Brightness ···············································································54

d Chroma Level ··········································································54

f Hue ························································································· 54

g DNR ························································································ 54

h Enhancer ················································································· 54

j Sharpness ···············································································54

Parameter

Status ····························································································54

a MAIN ZONE ············································································ 54

s ZONE2/3/4 ·············································································· 54

Audio Input Signal ········································································55

HDMI Information ········································································· 55

a Signal Information ··································································· 55

s Monitor1 ················································································· 55

d Monitor2 ················································································· 55

Auto Surround Mode ··································································· 55

Quick Select ·················································································· 55

Preset Station ··············································································· 55

Information

Playback

Main Remote Control Unit ··························································76

Operating DENON Audio Components ········································76

Presetting ·····················································································76

Operating Preset Components ············································76 ~ 78

Setting the Remote ID ·································································79

Learning Function ··································································79, 80

System Call Function ···································································80

Punch Through Function ······························································80

Setting the Time the Backlight Stays Lit ······································81

Adjusting the Backlight’s Brightness ···········································81

Resetting the Main Remote Control Unit ····································81

Sub Remote Control Unit Operations ·································· 82, 83

Switching Zones ··········································································84

Setting the Zone for Which the Sub Remote Control Unit

is Used (ZONE SELECT LOCK Mode) ··········································84

Setting the Remote ID ·································································84

Resetting the Settings ·································································84

Remote Control Unit Operations

Other Operations ·········································································· 71

Playing Super Audio CD ·······························································71

Recording on an External Device (REC OUT mode) ··············71, 72

Convenient Functions ·································································· 73

HDMI Control Function ································································73

Channel Level ··············································································74

Fader Function ·············································································74

Quick Select Function ··································································74

Personal Memory Plus Function ··················································75

Last Function Memory ·································································75

Backup Memory ···········································································75

Resetting the Microprocessor ·····················································75

Other Operations and Functions

Preparations ··················································································56

Turning the Power On ··································································56

Operations During Playback ·························································56

Playing Video and Audio Equipment ··········································56

Basic Operation ············································································56

Listening to FM/AM Broadcasts ················································· 57

Basic Operation ············································································57

Presetting Radio Stations (Preset Memory) ································· 57

Listening to Preset Stations ·························································58

RDS (Radio Data System) ····························································58

RDS Search ··················································································58

PTY Search ···················································································59

TP Search ·····················································································59

RT (Radio Text) ·············································································59

Listening to XM Satellite Radio Programs ·································60

Basic Operation ············································································60

Checking the XM Signal Strength and Radio ID ···························60

Searching Categories ···································································61

Accessing XM Radio Channels Directly ·······································61

Listening to HD Radio™ Stations ··············································· 61

Basic Operation ············································································62

Selecting Audio Programs ····························································62

Check the HD Radio Reception Information ································62

iPod

®

Playback ·············································································63

Basic Operation ············································································63

Listening to Music ·································································63, 64

Viewing Still Pictures or Videos on the iPod ································64

Playing Network Audio,

USB Memory Devices or Rhapsody ······································ 64, 65

Basic Operation ······································································65, 66

Listening to Internet Radio ···························································66

Playing Files Stored on a Computer ·············································67

Playing Files Stored on USB Memory Devices ······················ 67, 68

Listening to Rhapsody ···························································68, 69

Operating the AVR-5308CI Using a Browser (Web control) ··69, 70



Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

In addition to the AVR-5308CI, the included main remote control unit

(RC-1067) can also be used to operate the equipment listed below.

q DENON system components

w Non-DENON system components

• By setting the preset memory (vpage 76 ~ 78)

• By using the learn function (vpage 79)

q Lift the clasp and remove the rear lid.

e Put the rear cover back on.

(RC-1067) (RC-1070)

LR6/AA

R03/AAA

w Load the two batteries properly as indicated by the marks in the

battery compartment.

About the Remote Control Unit

Inserting the Batteries

• Before turning the power switch on

Check once again that all connections are correct and that there are

no problems with the connection cables.

•

Power is supplied to some of the circuitry even when the unit is

set to the standby mode. When traveling or leaving home for long

periods of time, be sure to unplug the power cord from the power

outlet.

• About condensation

If there is a major difference in temperature between the inside of

the unit and the surroundings, condensation (dew) may form on

the operating parts inside the unit, causing the unit not to operate

properly.

If this happens, let the unit sit for an hour or two with the power

turned off and wait until there is little difference in temperature

before using the unit.

• Cautions on using mobile phones

Using a mobile phone near this unit may result in noise. If so, move

the mobile phone away from this unit when it is in use.

• Moving the unit

Turn off the power and unplug the power cord from the power

outlet.

Next, disconnect the connection cables to other system units before

moving the unit.

•

Note that the illustrations in these instructions may differ from the

actual unit for explanation purposes.

Note:

For proper heat dispersal, do not install this unit in a conﬁned

space, such as a bookcase or similar enclosure.

b Note

b

Wall

b

Cautions on Handling

Cautions on Installation

Check that the following parts are supplied with the product.

q Owner’s manual ...................................................................... 1

w Warranty (for North America model only) ................................ 1

e Service station list ................................................................... 1

r Power cord (Cord length: Approx. 5 ft /1.5 m) ........................ 1

t Main remote control (RC-1067) ............................................... 1

y LR6/AA batteries (for RC-1067) ............................................... 2

u Sub remote control (RC-1070) ................................................. 1

i R03/AAA batteries (for RC-1070) ............................................. 2

o FM indoor antenna .................................................................. 1

Q0 AM loop antenna (small, for AM broadcasts) .......................... 1

Q1 AM loop antenna (large, for HD Radio broadcasts) ................. 1

Q2 Dipole antenna (for HD Radio broadcasts) .............................. 1

Q3 Rod antenna for wireless LAN connection .............................. 1

Q4 Setup microphone (Cord length: Approx. 25 ft / 7.6 m) .......... 1

r t u

Q1

o

Q4Q3

Q0

Q2

Thank you for purchasing this DENON product. To ensure proper

operation, please read this owner’s manual carefully before using the

product.

After reading them, be sure to keep them for future reference.

Getting Started

Accessories

Getting Started



Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

For buttons not explained here, see the page indicated in parentheses ( ).

q w e r t

yioQ0

Q1 Q2 Q3 Q4

u

Part Names and Functions

Front Panel

q Power operation button

(ON/STANDBY) ·······································································(56)

w Power indicator ·······································································(56)

e Power switch (hON jOFF) ··················································(56)

r Door ····························································································(5)

t QUICK SELECT buttons / indicators ······································ (74)

y MASTER VOLUME control knob ············································(56)

u Master volume indicator

i Display ························································································(5)

o Remote control sensor ·····························································(4)

Q0 SOURCE SELECT knob ···························································(43)

Q1 SOURCE button ·······································································(43)

Q2 TUNING PRESET button ·························································(57)

Q3 ZONE2/3/4 / REC SELECT button ····································(71, 90)

Q4 VIDEO SELECT button ····························································(45)

30°

Approx. 23 feet / 7 m

or

(RC-1067)

(RC-1070)

NOTE

• Replace the batteries with new ones if the set does not operate

even when the remote control unit is operated close to the unit.

• The supplied batteries are only for verifying operation.

• When inserting the batteries, be sure to do so in the proper direction,

following the “q” and “w” marks in the battery compartment.

• To prevent damage or leakage of battery ﬂuid:

• Do not use a new battery together with an old one.

• Do not use two different types of batteries.

• Do not attempt to charge dry batteries.

• Do not short-circuit, disassemble, heat or dispose of batteries in

ﬂames.

• If the battery ﬂuid should leak, carefully wipe the ﬂuid off the inside

of the battery compartment and insert new batteries.

• Remove the batteries from the remote control unit if it will not be in

use for long periods.

• When replacing the batteries, have the new batteries ready and

insert them as quickly as possible.

Operating Range of the Remote Control

Unit

Point the remote control unit at the remote sensor when operating it.

NOTE

The set may function improperly or the remote control unit may not

operate if the remote control sensor is exposed to direct sunlight,

strong artiﬁcial light from an inverter type ﬂuorescent lamp or infrared

light.

Getting Started



Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

t

uQ4Q8Q9 o iQ1

Q0Q6 Q2

Q3Q5Q7 y

wq e r

q Input signal indicators

w Input signal channel indicators

These light when digital signals are input.

e Information display

The input source name, surround mode, setting

values and other information are displayed

here.

r Output signal channel indicators

t Surround speaker indicators

These light according to the settings of the

surround A and B speakers.

y Monitor output indicators

These light according to the HDMI monitor

output setting. When set to “Auto (Dual)”, the

indicators light according to the connection

status.

u Master volume indicator

i AUDYSSEY DYNAMIC EQ indicator

This lights when the Dynamic EQ is selected.

o AUDYSSEY MULTEQ XT indicator

This lights when the room equalizer is selected.

Q0 Recording output source indicator

This lights when the REC OUT mode is

selected.

Q1 NIGHT indicator

This lights when the night mode is selected.

Q2 Multi zone indicators

These light when the power for the respective

zone is turned on.

Q3 RESTORER indicator

This lights when the RESTORER mode is

selected.

Q4 ADVANCED AL24 indicator

This lights when Advanced AL24 Processing is

activated (vpage 95).

Q5 D.LINK indicator

This lights when playing using DENON LINK

connections.

Q6 Input mode indicators

Q7 HDMI indicator

This lights when playing using HDMI

connections.

Q8 Decoder indicators

These light when the respective decoders are

operating.

Q9 Tuner reception mode indicators

These light according to the reception conditions

when the input source is set to “TUNER” or

“HD Radio”.

• AUTO

This lights when in the auto tuning mode.

• RDS

These light when receiving RDS broadcasts.

• STEREO

In the FM mode, this lights when receiving

analog stereo broadcasts.

• TUNED

This lights when the broadcast is properly tuned

in.

Display

q DIRECT/STEREO button ···························· (49)

w Headphones jack (PHONES) ················ (56, 72)

e CINEMA button ·········································· (48)

r RESTORER button ······································ (53)

t MUSIC button ············································· (48)

y NIGHT button ············································· (53)

u MENU button ·············································· (25)

i CH SEL / ENTER button ························(25, 74)

o RETURN button ·········································· (25)

Q0 V.AUX INPUT connectors ·························· (18)

Q1 ROOM EQ button ······································· (53)

Q2 SETUP MIC jack ·········································· (27)

Q3 DYNAMIC EQ button ·································· (53)

Q4 STATUS button ·········································· (55)

Q5 DIMMER button ·········································· (42)

Q3Q4Q5Q6Q7Q8Q9W0W1W2W3W4W5W6W7W8W9

q w e r t y u i o Q0 Q1 Q2

GWith the door openH

Q6 SCALE button ············································· (45)

Q7 USB port ······················································ (19)

Q8 ZONE4 ON/OFF button ······························ (90)

Q9 ZONE3 ON/OFF button ······························ (90)

W0 ZONE2 ON/OFF button ······························ (90)

W1 AUDIO DELAY button ································ (54)

W2 Cursor buttons (uio p) ·························· (25)

W3 GAME button ········································ (14, 48)

W4 INPUT MODE button ·································· (45)

W5 7CH STEREO button ··································· (49)

W6 DSP SIMULATION button ·························· (49)

W7 HOME THX CINEMA button ······················ (48)

W8 STANDARD button ····································· (48)

W9 PURE DIRECT button ································· (50)

Getting Started



Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

q

W0 W1 W2

w e r t y

ui

oQ0Q1Q2Q3Q4Q5Q6Q7Q8Q9u

q RS-232C connector ····································· (24)

w Analog audio connectors (AUDIO) ··········· (13)

e PRE OUT connectors ···························· (19, 23)

r EXT. IN connectors ····································· (18)

t AC inlet (AC IN) ··········································· (24)

y AC OUTLETS ··············································· (24)

u Speaker terminals (SPEAKERS) ················ (10)

i HD Radio antenna terminals

(DTU ANTENNA) ········································ (21)

o COMPONENT VIDEO connectors ·············· (13)

Q0 Digital audio connectors

(OPTICAL / COAXIAL / BNC) ··············· (13, 23)

Q1 HDMI connectors ········································ (12)

Q2 ETHERNET connector ································ (22)

Q3 USB port ······················································ (19)

Q4 XM connector (SAT TU) ····························· (20)

Q5 WLAN ANTENNA terminal ························ (22)

Q6 FM/AM antenna terminals

(TUNER ANTENNA) ···································· (21)

Q7 DENON LINK connector ····························· (18)

Rear Panel

Q8 TRIGGER OUT jacks ··································· (24)

Q9 REMOTE CONTROL jacks ·························· (23)

W0 DOCK CONTROL jack ································· (14)

W1 SIGNAL GND terminal ······························· (14)

W2 VIDEO / S-VIDEO connectors ···················· (13)

Getting Started



Connections Setup Playback Remote Control Multi-Zone Information Troubleshooting

q

i

w

e

r

t

y

u

o

Q1

Q3

Q4

Q2

Q0

Q5

Q6

Q7

Q9

W0

W2

W5

W7

W6

W4

W3

W1

Q8

q Signal transmission indicator ··················· (76)

w Mode select buttons ·································· (76)

e Quick select / System call buttons ······(74, 80)

r Surround mode buttons ····················(48 ~ 50)

t System buttons ·····································(77, 78)

y Audio delay button (A. DL) ························ (54)

u Tuner system buttons ································ (57)

i Input mode button (INPUT) ······················· (45)

o MENU button ·············································· (25)

Q0 Cursor buttons (uio p) ························· (25)

Q1 Parameter / Search button

(PARA / SRCH) ·························· (50, 58, 61, 64)

Q2 Monitor select (M. SEL) /

HOME button ········································ (33, 76)

Q3 Channel buttons (CH) ································· (57)

Q4 Input source select /

Number buttons ··································· (43, 56)

Q5 Remote control signal transmitter ············· (4)

Q6 Device select indicators (DEV1 / DEV2) ··· (76)

Q7 ZONE3 / ZONE4 select indicators

(Z3 / Z4) ······················································· (90)

Q8 RESTORER button (RSTR) ························· (53)

Q9 Night button (NGT) ···································· (53)

W0 Test tone button (TEST) ···························· (31)

W1 Surround speaker select button (SPKR) ···· (32)

W2 POWER buttons ·········································· (56)

W3 Channel select (CH SEL) /

ENTER button ········································(25, 74)

W4 Return button (RTN) ·································· (25)

W5 Master volume control buttons (VOL) ····· (56)

W6 Muting button (MUTE) ························ (56, 90)

W7 Main remote control unit setup button

(RC SETUP) ················································· (76)

q

r

t

y

i

o

Q0

u

e

w

Q4

Q7

Q8

Q9

W0

Q6

Q5

Q2

Q3

Q1

q ZONE indicators ········································· (84)

w Advanced setup button ····························· (84)

e Input source select buttons ······················· (43)

r CHANNEL buttons ······································ (57)

t SHIFT button ··············································· (57)

y MENU button ·············································· (25)

u Cursor buttons (uio p) ························· (25)

i SEARCH button ······························ (58, 61, 64)

o REPEAT button ··········································· (63)

Q0 RANDOM button ········································ (64)

Q1 Remote control signal transmitter ············· (4)

Q2 ZONE SELECT button ································ (84)

Q3 Zone power on/off buttons

(ZONE ON / ZONE OFF) ····························· (90)

Q4 Master volume control buttons

(VOLUME) ·················································· (56)

Q5 Muting button (MUTE) ························ (56, 90)

Q6 ENTER button ············································· (25)

Q7 RETURN button ·········································· (25)

Q8 System buttons ·······························(57, 82, 83)

Q9 ALL MUSIC/FAVORITES

(DIRECT PLAY) button ······························ (82)

W0 USB (DIRECT PLAY) button ······················· (82)

n Main remote control unit (RC-1067) n Sub remote control unit (RC-1070)

The time for which the backlight stays on can

be changed (vpage 81 “Setting the Time the

Backlight Stays Lit”).

Remote Control Unit

NOTE

The ZONE2 mode QUICK SELECT (1 ~ 3), A. DL,

RSTR, NGT, INPUT, SPKR, TEST and surround

mode buttons cannot be used.

NOTE

The AUX-1, AUX-2, AUX-3 and OPTION buttons

cannot be used.

Getting Started



Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

Audio cables Video cables

Coaxial digital connections

(Orange)

Coaxial digital (75 Ω/ohms pin-plug) cable

Optical digital connections

Optical cable

BNC digital connections

BNC (75 Ω/ohms) cable

Analog connections (stereo)

(White)

(Red)

R

L

R

L

Stereo pin-plug cable

Analog connections (monaural, for subwoofer)

(Black)

Pin-plug cable

DENON LINK connections

DENON LINK cable

Speaker connections

Speaker cables

Network connections (wired LAN)

Ethernet cable

Component video connections

(Green)

(Blue)

(Red)

(Y)

(PB/CB)

(PR/CR)

Component video cable

(Green)

(Blue)

(Red)

(Y)

(PB/CB)

(PR/CR)

BNC (75 Ω/ohms) cable

S-Video connections

S-Video cable

Video connections

(Yellow)

75 Ω/ohms pin-plug video cable

Audio and video cables

HDMI connections

19-pin HDMI cable

Signal direction

Audio signal: Video signal:

Output

Input

Output

Input

Output

Connections

NOTE

• Do not plug in the power cord until all connections have been

completed.

• When making connections, also refer to the operating instructions of

the other components.

• Be sure to connect the left and right channels properly (left with left,

right with right).

• Do not bundle power cords together with connection cables. Doing

so can result in humming or noise.

Connections for all compatible audio and video signal formats are

described in these operating instructions. Please select the types

of connections suited for the equipment you are connecting.

With some types of connections, certain settings must be made

on the AVR-5308CI. For details, refer to the instructions for the

respective connection items below.

Cables Used for Connections

Select the cables according to the equipment being connected.

Preparations

Connections



Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

GFlow of video signals for ZONE2H

• This function automatically converts various formats of video signals input to the AVR-5308CI into the

format used to output the video signals from the AVR-5308CI to a monitor.

• The AVR-5308CI’s video input/output circuitry is compatible with the following four types of video

signals:

Digital video signals: HDMI

Analog video signals: Component video, S-Video and Video

Video Conversion Function

GFlow of video signals inside the AVR-5308CIH

MAIN ZONE

High picture

quality playback

HDMI connector

Component video

connectors

S-Video connector

Video connector

Monitor

HDMI connector

Component video

connectors

S-Video connector

Video connector

Video inputs Video outputs

: When 480i/576i signals are input

Component video

connectors

S-Video connector

Video connector

Component video

connectors

Video connector

Video inputs Video outputs

ZONE2

NOTE

• For optimum video performance, THX recommends that you set the conversion mode to “OFF” to use

video signals pass through system without up conversion.

Example: The video input signals from the component video can be enjoyed through the video output

signals from the component video.

• HDMI signals cannot be converted into analog signals.

• 1080p component input video signals cannot be output to anything other than component video

connectors.

• 480p/576p, 1080i and 720p component video input signals cannot be converted into S-Video or Video

format.

• When using the component video output connectors for connection to the ZONE2 monitor, the ZONE2’s

on-screen display is not displayed.

• When a non-standard video signal from a game machine or some other source is input, the video

conversion function might not operate.

• When not using this function, connect a monitor output with the same type of connector as the video

input connector.

• The resolution of the HDMI input-compatible monitor connected to the AVR-5308CI can be checked at

GUI menu “Information” – “HDMI Information” – “Monitor1” or “Monitor2” (vpage 55).

High picture

quality playback

ZONE2

monitor

GFlow of video signals for ZONE3H

S-Video connector

Video connector Video connector

Video inputs Video outputs

ZONE3

High picture

quality playback

ZONE3

monitor

S-Video connector

Connections

0

Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

Speaker Installation

(L)

(R)

w q

*/

(L)

(R)

(L)

(R)

(L)

w q

*/ */

The illustration below shows a basic example of installation of the ampliﬁer combined with 8 speakers and

a monitor.

Speaker Layout

Subwoofer Center speaker

Surround speakers

Front speakers

Place the front speakers to the

sides of the monitor or screen and

as ﬂush with the screen surface as

possible.

Surround back speakers

The table below shows a typical speaker conﬁguration for the AVR-5308CI.

FRONT

CENTER

SURROUND

A

SURROUND

B

SURROUND BACK

SUBWOOFER

(b)

L R L R L R L R 1 only

9.1-channels

S S S S S S S S S

–

S

7.1-channels

S S S S S

– –

S S

–

S

6.1-channels

S S S S S

– – – –

S S

5.1-channels

S S S S S

– – – – –

S

3.1-channels

S S S

– – – – – – –

S

2.1-channels

S S

– – – – – – – –

S

2-channels

S S

– – – – – – – – –

Speaker Connections

Example: 9.3-channels and ZONE2 use

Front speaker (R) Center speaker Subwoofer 1

Subwoofer

with built-in

ampliﬁer

Surround

speaker-

A (R)

Surround

speaker-

B (R)

ZONE2 speakers

ZONE2

When using just one surround back speaker, connect it to the left channel (SBL).

NOTE

By default, the AVR-5308CI’s “Amp Assign” setting is set to “ZONE2”, so sound is not output simply by

connecting a speaker to the surround back terminal. To use as the surround back speaker for the MAIN

ZONE, either turn the ZONE2 power off or change the “Amp Assign” setting (vpage 85 ~ 88).

b L : Left

R : Right

Two surround back speakers are required to use the THX Ultra2 Cinema,THX Music mode and THX Games

mode.

Set the surround back speakers so that the distance to the listening position is the same for both the left

and right speakers. It is also recommended that the deviations of the distance from the listening position

to L and R channel speakers (front left (FL) and front right (FR), surround left (SL) and surround right (SR),

surround back left (SBL) and surround back right (SBR)) is less than 2 ft (60 cm).

Front speaker (L)

Surround

back

speaker

(R)

Surround

speaker-

B (L)

Surround

speaker-

A (L)

b The AVR-5308CI can be connected to a maximum of 3 subwoofers.

Connections

Subwoofer with built-in

ampliﬁer

Surround

back

speaker

(L)

Subwoofer 3 Subwoofer 2



Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

Connecting the Speaker Cables

Carefully check the left (L) and right (R) channels and + (red) and –

(black) polarities on the speakers being connected to the AVR-5308CI,

and be sure to interconnect the channels and polarities correctly.

1

Peel off about 0.03 ft/10 mm of sheathing

from the tip of the speaker cable, then

either twist the core wire tightly or

terminate it.

2

Turn the speaker terminal

counterclockwise to loosen it.

3

Insert the speaker cable’s core wire to

the hilt into the speaker terminal.

4

Turn the speaker terminal clockwise to

tighten it.

When using a banana plug

Tighten the speaker terminal ﬁrmly before

inserting the banana plug.

NOTE

• Use speakers with an impedance of 6 to 16 Ω/ohms. When using

surround A and B speakers simultaneously, use speakers with an

impedance of 8 to 16 Ω/ohms.

• Connect the speaker cables in such a way that they do not stick out

of the speaker terminals. The protection circuit may be activated if

the core wires touch the rear panel or if the + and – sides touch each

other (v “Protection circuit”).

• Never touch the speaker terminals while the power supply is

connected. Doing so could result in electric shock.

Protection circuit

If speakers with an impedance lower than speciﬁed (for example

4 Ω/ohms speakers) are used for an extended period of time with

the volume turned up high, the temperature may rise, activating the

protection circuit.

When the protection circuit is activated, the speaker output is shut

off and the power indicator ﬂashes red. If this happens, unplug

the power cord, then check the speaker cable and input cable

connections. If the set is extremely hot, wait for it to cool off and

improve ventilation around it. Once this is done, plug the power cord

back in and turn the set's power back on.

If the protection circuit is activated again even though there are no

problems in the ventilation around the set nor in the connections,

the set may be damaged. Turn the power off, then contact a DENON

service center.

Connections



Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

With HDMI connections, the video and audio signals can be transferred

with a single cable.

065

)%.*

*/

)%.*

Compatible audio

format

Details

Discs

(examples)

2-channel linear PCM

2ch 32-192 kHz

16/20/24 bits

CD, DVD-Video,

DVD-Audio

Multi-channel linear

PCM

8ch 32-192 kHz

16/20/24 bits

DVD-Audio

Dolby Digital, DTS Bitstream DVD-Video

DSD

2/5.1ch

2.8224 MHz

1 bit

SACD

Dolby Digital Plus,

Dolby TrueHD,

DTS-HD

Bitstream

HD DVD,

Blu-ray Disc

MonitorDVD player

b The AVR-5308CI is supported to the feature of HDMI listed below.

• 30 and 36 bit Deep Color

• xvYCC

• Auto Lipsync Correction

Copyright protection system (HDCP)

In order to play the digital video and audio signals of a DVD- Video or

DVD-Audio disc using HDMI/DVI connections, both the connected

DVD player and monitor must be equipped for a copyright protection

system called “HDCP” (High-bandwidth Digital Content Protection).

HDCP is a copy protection technology consisting of data encoding

and mutual identiﬁcation of the devices.

The AVR-5308CI is HDCP-compatible. For details on the DVD player

or monitor you are using, refer to its operating instructions.

• When the AVR-5308CI and DVD player are connected using an HDMI

cable, also connect the AVR-5308CI and monitor using an HDMI

cable.

• If the connected monitor or DVD player only has a DVI-D connector,

use an HDMI/DVI converter cable. When using a DVI cable, no audio

signals are transmitted.

• Use a Deep Color compatible cable for connection to Deep Color

compatible devices.

When connecting with an HDMI/DVI converter cable

(adapter)

• HDMI video signals are theoretically compatible with the DVI

format.

When connecting to a monitor, etc., equipped with a DVI-D

connector, connection is possible using an HDMI/DVI converter

cable, but depending on the combination of components in some

cases the video signals will not be output.

• When connecting using an HDMI/DVI converter adapter, the video

signals may not be output properly due to poor connections with

the connected cable, etc.

• By default, the HDMI audio signals are output from the speakers

connected to the AVR-5308CI.

• To output the sound from the TV, make the settings at GUI menu

“Manual Setup” – “HDMI Setup” – “Audio” – “TV” (vpage 33).

NOTE

• Use a CPPM-compatible DVD player to play DVD-Audio discs that are

copyright-protected by CPPM.

• The audio signals output from the HDMI connector (sampling

frequency, bit rate, etc.) may be restricted by the connected device.

• Video signals are not output properly when using devices that are

not HDCP-compatible.

• Video signals are not output if the input video signals do not match

the monitor’s resolution. In this case, switch the DVD player’s

resolution to a resolution with which the monitor is compatible.

• If the GUI menu “Manual Setup” – “HDMI Setup” – “Audio” setting

(vpage 33) is set to “Amp”, the sound may be interrupted when the

monitor’s power is turned off.

• Use a cable on which the HDMI logo is indicated (a certiﬁed HDMI

product) for connection to the HDMI connector. Normal playback

may not be possible when using a cable other than one on which the

HDMI logo is indicated (a non-HDMI-certiﬁed product).

• If the monitor or DVD player does not support Deep Color, Deep

Color signal transfer is not possible.

• If the monitor or DVD player does not support xvYCC, xvYCC signal

transfer is not possible.

• If the monitor does not support “Auto Lipsync Correction” function,

this function will not work.

• The AVR-5308CI is compatible with the HDMI’s CEC (Consumer

Electronics Control) function. Please note the following.

•

It may not work depending on the device it is connected to and its

setup.

•

It does not operate with televisions or players that are not

compatible with HDMI’s CEC.

Connecting Equipment with HDMI

connectors

Connections



Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

• Connect the cables to be used (vpage 9 “Video Conversion Function”).

• With HDMI connections, the video and audio signals can be transferred with a single cable.

• To output the audio signals to the monitor with HDMI connections, set GUI menu “Manual Setup”

– “HDMI Setup” – “Audio” to “TV” (vpage 33).

Connecting the Monitor

47*%&0

*/

7*%&0

$0.10/&/57*%&0

: 1# 13

7*%&0

*/

)%.*

*/ */

47*%&0

065

"6%*07*%&0

$0.10/&/57*%&0

: 1# 13

7*%&0

065 065

"6%*0

$0"9*"-

065

3-

065065

)%.*

R

L

R

L

Monitor

Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect

correctly.

Connecting the Playback Components

DVD Player

• Connect the cables to be used.

• With HDMI connections, the video and audio signals can be transferred with a single cable.

DVD player

NOTE

• The component video connectors may be indicated differently on your monitor. For details, see the

monitor’s operating instructions.

• The audio signals output from the HDMI connectors are only the HDMI input signals.

• Connect an HDP (High-Deﬁnition Player) in the same way.

• When using an optical cable or a BNC cable for the digital audio connection, make the settings at GUI

menu “Source Select” – “DVD” – “Assign” – “Digital” (vpage 46).

• When using a BNC cable for the component video connection, make the settings at GUI menu “Source

Select” – “DVD” – “Assign” – “Component” (vpage 47).

Connections



Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

Record Player

• When connecting a record player with an MC cartridge, use a

commercially available MC head ampliﬁer or a step-up transformer.

• Induction humming (a booming sound) may be produced from the

speakers if the volume is raised with no record player connected.

• With some record players, noise may be generated when the ground

wire is connected. If so, disconnect the ground wire.

(/%

"6%*0

065

R

L

Turntable (MM cartridge)

NOTE

The AVR-5308CI’s SIGNAL GND terminal is meant to reduce noise

when a record player is connected. This is not a safety ground

terminal.

R

L

R

L

"6%*0

$0"9*"-

065

3-

065

CD Player

Connect the cables to be used.

CD player

iPod

®

Example :

R

L

R

L

"4%3

iPod

When using an optical cable or a BNC cable for the digital audio

connection, make the settings at GUI menu “Source Select” – “CD”

– “Assign” – “Digital” (vpage 46).

• With the default settings, the iPod can be used connected to the VCR

(iPod) connector.

• To assign the iPod to a connector other than VCR (iPod), make the

settings at GUI menu “Source Select” – “(input source to which iPod

dock assigned)” – “Assign” – “iPod dock” (vpage 47).

Use a DENON Control Dock for iPod (ASD-1R, sold separately) to

connect the iPod to the AVR-5308CI. For instructions on the Control

Dock for iPod settings, refer to the Control Dock for iPod’s operating

instructions.

Connections



Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

47*%&0

065

"6%*07*%&0

$0.10/&/57*%&0

: 1# 13

7*%&0

065 065

"6%*0

3-

065065

R

L

R

L

015*$"-

TV/CABLE Tuner

Connect the cables to be used.

TV tuner

• When using a coaxial digital cable or a BNC cable for the digital audio connection, make the settings at

GUI menu “Source Select” – “TV/CBL” – “Assign” – “Digital” (vpage 46).

• When using a BNC cable for the component video connection, make the settings at GUI menu “Source

Select” – “TV/CBL” – “Assign” – “Component” (vpage 47).

Satellite Receiver

Connect the cables to be used.

47*%&0

065

"6%*07*%&0

$0.10/&/57*%&0

: 1# 13

7*%&0

065 065

"6%*0

3-

065

R

L

R

L

065

)%.*

$0"9*"-

065

DBS / BS tuner

• When using an optical cable or a BNC cable for the digital audio connection, make the settings at GUI

menu “Source Select” – “SAT” – “Assign” – “Digital” (vpage 46).

• When using a BNC cable for the component video connection, make the settings at GUI menu “Source

Select” – “SAT” – “Assign” – “Component” (vpage 47).

Connections



Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

Carefully check the left (L) and right (R) channels and the inputs and outputs, and be sure to interconnect correctly.

Connecting the Recording Components

Digital Video Recorder

Connect the cables to be used.

R

L

R

L

R

L

R

L

47*%&0 47*%&0

*/

3-3-

*/

"6%*0 "6%*07*%&0 7*%&0

*/065

015*$"- 015*$"-

065

"6%*0 "6%*0

065

7*%&0 7*%&0

065

)%.*

$0.10/&/57*%&0

: 1# 13

065

Digital video recorder

NOTE

• Do not connect the output of the component connected to the AVR-

5308CI’s OPTICAL2 output connector to any input connector other

than OPTICAL2.

• Do not connect the output of the component connected to the AVR-

5308CI’s OPTICAL3 output connector to any input connector other

than OPTICAL3.

• Make analog connections if you wish to record analog audio signals.

• When recording to a digital video recorder, it is necessary that the

type of cable used with the playback source equipment be the same

type that is connected to the AVR-5308CI DVR-1 OUT connector.

Example: TV IN → S-Video cable : DVR-1 OUT → S-Video cable

TV IN → Video cable : DVR-1 OUT → Video cable

• Connect a DVR-2 in the same way.

• When using a component video cable or a BNC cable for the

component video connection, make the settings at GUI menu

“Source Select” – “DVR-1” or “DVR-2” – “Assign” – “Component”

(vpage 47).

Connections



Getting Started Setup Playback Remote Control Multi-Zone Information Troubleshooting

R

L

R

L

R

L

R

L

47*%&0 47*%&0

*/

3-3-

*/

065

"6%*0 "6%*07*%&0 7*%&0

*/065

015*$"- 015*$"-

065

"6%*0 "6%*07*%&0 7*%&0

065

)%.*

Video Cassette Recorder

Connect the cables to be used.

Video cassette recorder

• When recording to a VCR, it is necessary that the type of cable used with the playback source equipment

be the same type that is connected to the AVR-5308CI VCR OUT connector.

Example: TV IN → S-Video cable : VCR OUT → S-Video cable

TV IN → Video cable : VCR OUT → Video cable

• When using a component video cable or a BNC cable for the video connection, make the settings at GUI

menu “Source Select” – “VCR” – “Assign” – “Component” (vpage 47).

NOTE

Do not connect the output of the component connected to the AVR-5308CI’s OPTICAL4 output connector

to any input connector other than OPTICAL4.

3-3-

*/ */065

015*$"- 015*$"-

065

"6%*0"6%*0

"6%*0

R

L

R

L

R

L

R

L

CD Recorder / MD Recorder / Tape Deck

Make analog connections if you wish to record analog audio signals, or digital connections if you wish to

record digital audio signals, depending on the types of connectors on the components being used.

CD recorder /

MD recorder / Tape deck

NOTE

Do not connect the output of the component connected to the AVR-5308CI’s OPTICAL4 output connector

to any input connector other than OPTICAL4.

Connections

Page is loading ...

Denon AVR-5308CI(A) User guide

Related papers

Other documents