Atlantis A05-17AM-L02 User manual

I-See S 173

A05-17AM-L02

USER MANUAL

A05-17AM-L02_MX01

Page is loading ...

A05-17AM-L02_MX01

Copyright

The Atlantis Land logo is a registered trademark of Atlantis Land SpA.

All other names mentioned mat be trademarks or registered

trademarks of their respective owners. Subject to change without

notice. No liability for technical errors and/or omissions.

CE Mark Warning

This is a Class B product. In a domestic environment, this product

may cause radio interference, in which case the user may be required

to take adequate measures.

Important Note

The antenna(s) used for this equipment must be installed to provide a

separation distance of at least 30 cm from all persons.

FCC Warning

This equipment has been tested and found to comply with the

regulations for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and

used in accordance with this user’s guide, may cause harmful

interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference, in which case

the user will be required to correct the interference at his own

expense.

Page is loading ...

A05-17AM-L02_MX01

8

APPENDICE C: RESOLUTION TABLE

RISOLUZIONE FREQUENZA

ORIZZONTALE

RISOLUZIONE FREQUENZA

VERTICALE

640×480 60Hz 800×600 75Hz

720×400 70Hz 1024×768 60Hz

640×480 72Hz 1024×768 70Hz

640×480 75Hz 1024×768 75Hz

800×600 56Hz 1280×1024 60Hz

800×600 60Hz 1280×1024 75Hz

800×600 72hz

APPENDICE D: CAVO D-SUB

PIN NO. DESCRIZIONE PIN NO. DESCRIZIONE

1. Red 9. +5V

2. Green 10. Ground

3. Blue 11. Ground

4. Ground 12. DDC-Serial Data

5. Ground 13. H-Sync

6. R-Ground 14. V-Sync

7. G-Ground 15. DDC-Serial Clock

8. B-Ground

A05-17AM-L02_MX01

9

ENGLISH

1.0 Before start

This monitor is a high-performance intelligent multi-scanning color

monitor adopting active matrix TFT LCD display that uses amorphous

silicon TFT as a switching devices. With very low radiation, anti-glary

surface treatment and occupying small place , it is very suitable for

home and office applications.

1.2 Features

• LCD TFT monitor

• Built-in multimedia speakers

• Multi-language OSD interface

• Image auto regulation

• White and black reference voltage auto-calibration

• Plug & Play

1.3 Check List

Check the list before operating this monitor, please make sure that all

of the following items are included.

1. LCD monitor

2. AC adapter

3. Power cord

4. Signal cable

5. Audio cable

6. User’s manual

7. Warranty certification

If any of above listed items is missing, please contact your dealer for

technical support or customer service.

2. Installation

The following chapters explain how to install the base and connect

the monitor to your personal computer.

2.1 Install the monitor

Make sure that the computer and monitor’s power are both turned off,

before start installation. Please follow the steps to install your LCD

monitor:

1. Signal cable connection: firstly lock the base and knighthead,

then Plug one end of the signal cable into computer and lock the

A05-17AM-L02_MX01

10

two bolts to ensure firmly grounding. Then plug the other into the

monitor and lock the two bolts.

2. Power cord connection: connect the AC adapter and AC power

source with power cord. then connect the AC adapter output to

the power input of the monitor.

3. Audio cable connection: Insert one end of the audio cable to the

audio output of the PC audio card and the another to the audio

input of LCD monitor.

4. Power on: turn on both of the monitor and computer. After the

monitor is power on, the LED lights up green or blue, If the LED

become red and flashing, please check the video signal cable. If

LED is off, please press power on switch.

2.2 Product positioning

• Avoid a direct lightening of the monitor by sources of light. To

control natural light, is possible to use curtains, better ones of a

neutral colour.

• The screen should be put aside walls with windows and if you

have a window in front of you it must be screened with curtains.

• Most used documents should be kept near the monitor in order

to have not to turn your head frequently always changing your

focus.

• Most used objects should be positioned as near as possible, the

ones less used can be kept a little further, but they should be

easily reachable too.

3.0 Operating instructions

3.1 Front panel controls

• Auto Adjust Key:

When OSD menu is in off status, press this button direct to

activate the Auto adjustment function.

The Auto Adjustment function is used to set the Hpos, Vpos,

Clock and Focus.

This button is the input switch for analog /digital signal while with

DVI function.

• Brightness

:

Adjust brightness or adjust function (tone down the volume while

have the audio frequency)

A05-17AM-L02_MX01

11

• Contrast :

Adjust contrast or adjust function.(tone up the volume while have

the audio frequency)

• MENU ：

Activate the OSD menu or confirm the function adjusting.

• Power Key

：

Press this button to switch ON/OFF of monitor’s power.

• Power Indicator:

Blue/Green ---- Power On mode.

Orange/Red ---- Off mode.

3.2 How to adjust a setting

1. Press the MENU button to activate the OSD window.

2. Press

or to select the desired function, then press the

MENU button again.

3. Press

or to change the settings of the current function

,press the MENU button to confirm it.

4. If you want to adjust any other function, repeat steps 2-3.

5. If you want to exit the OSD image, select the “exit function/EXIT

OSD”, or leave the monitor alone for 20 seconds (Windows

default), the OSD window will close and sure automatically.

6. When the OSD window is active, it shows the input signal timing.

3.3 Adjusting the picture

1. BRIGHTNESS

1.1 Auto gain control: Adjust the gain automatically.

1.2 Brightness: Adjust the brightness automatically.

1.3 Contrast: Adjust the contrast automatically.

1.4 Exit

2. COLOR (In the state of DVI without this item)

2.1 Auto color: Adjust the color automatically.

2.2 Exit

A05-17AM-L02_MX01

12

3. IMAGE (In the state of DVI without this item)

3.1 Auto configuration: Adjust the image position automatically

3.2 Clock: Adjust the image clock.

3.3 Phase: Adjust the image focus

3.4 H-Position: Adjust the image horizontal position

3.5 V-Position: Adjust the image vertical position.

3.6 Exit

4. TOOLS

4.1 OSD Timeout: Control the quit time of quit the OSD menu

automatically.

4.2 OSD H-Position: Adjust the horizontal position of OSD menu.

4.3 OSD V.-Position: Adjust the vertical position of OSD menu.

4.4 Volume(with the function of audio frequency): Adjust the volume

of the speaker.

4.5 Factory reset: Recall to factory setting

4.6 Exit

5. COLOR TEMP: selection 5000k warm, 6500k standard, 9300k

cool. If 5000k,6500k,9300k can’t meet your need, you can use USER-

DEFINED menu to adjust the red , green and blue to gain the color

which you like.

6. LANGUAGE: Choose the language of OSD menu, you can choose

English 、Czech、Russia、German、Polish etc.

7. ANALOG/DIGITAL (with the function of DVI): Select the right input.

8. EXIT: Exit OSD menu.

4.0 Trouble-Shooting

Problem & Question Possible Solution

Power LED is not on Check if the Power Switch is in the ON

position

Power Cord should be connected

No Plug & Play Check if the PC system is Plug & Play

A05-17AM-L02_MX01

13

compatible

Check if the Video Card is Plug & Play

compatible

Check if the D-15 plug pin of Video

Cable is bent

Picture is fuzzy Adjust the Contrast and Brightness

Controls.

Picture bounces or a

wave pattern is present

in the picture

Move electrical devices that may cause

electrical interference.

The power LED is

ON(Red) but there's no

video or no picture.

Computer Power Switch should be in the

ON position.

Computer Video Card should be snugly

seated in its slot

Make sure monitor's video cable is properly

connected to the computer.

Inspect monitor's video cable and rnake

sure none of the pins are bent.

Make sure computer is operational by

hitting the CAPS LOCK key on the

keyboard while observing the CAPS LOCK

LED. The LED should either turn ON or

OFF after hitting the CAPS LOCK key.

Missing one of the

primary

colors(RED,GREEN,or

BLUE)

Inspect the monitor's video cable and make

sure that none of the pins are bent.

Screen image is not

centered or sized

properly.

Adjust pixel frequency(CLOCK) and

PHASE or press hot-key (AUTO)

Picture has color

defects (white does not

look white)

Adjust RGB color or select color

temperature

Poor brightness or

The life time of the back-light is limited. In

30000 Hours the luminance of the light has

A05-17AM-L02_MX01

14

contrast been reduced to half of its original value.

Please send the monitor to an authorized

service Agent for service.

Horizontal or vertical

disturbances on the

screen

Use win 95/98/2000/XP shut-down mode

Adjust CLOCK and PHASE or perform hot-

key(AUTO-key).

APPENDIX A: SPECIFICATIONS

Model

A05-17AM-L02

Panel

17”

Resolution

1280 x 1024

Active area

337.920 x 270.336 mm

Pixel pitch

0.264 mm

Contrast

500:1

Brightness

300 cd/m

2

Response time

8 ms

Display colors

16.7 M

Viewing angle

H: -75°/+75°, V: -75°/+60°

H-Frequency

30~81 KHz

V-Frequency

55~75 Hz

Plug & Play

Yes

Input signal

Analog

Video Input connector

15 pins D-Sub

Audio input connector

1 Stereo input

Built-in speakers

2 x 2 W

Power input connector

Power jack

Maximum power cons.

<40 W

Stand-by power cons.

<5 W

Off mode powert cons.

<3 W

Power supply for adapter

100 V~240 VAC 60/50Hz

Power supply for monitor

12 VDC 4 A

Power saving control

Yes

Norms

CE

Storage temperature

-20°C~+55°C

Operating temperature

5°C~40°C

Humidity

10%~85%

Page is loading ...

A05-17AM-L02_MX01

16

APPENDIX D: D-SUB CABLE

PIN NO. DESCRIPTION PIN NO. DESCRIPTION

1. Red 9. +5V

2. Green 10. Ground

3. Blue 11. Ground

4. Ground 12. DDC-Serial Data

5. Ground 13. H-Sync

6. R-Ground 14. V-Sync

7. G-Ground 15. DDC-Serial Clock

8. B-Ground

Page is loading ...

Important information for the correct recycle/treatment procedures of this

equipment

The crossed-out wheeled bin symbol printed on the unit label or unit packaging

indicates that this equipment must not be disposed of as unsorted municipal waste but

it should be collected separately.

The waste of electric and electronic equipment

must be treated separately, in order to ensure

that hazardous materials contained inside the

equipment are not buried thereby providing

potential future problems for the environment

and human health. Moreover, it will be

possible to reuse and recycle some parts of

the waste of electric and electronic equipment,

contributing to reduce the quantities of waste

to be disposed of and the depletion of natural

resources.

As user of this equipment, you are responsible to return this waste of electronic

equipment to an authorised collection facility set up by your Municipality. More

detailed information on your nearest collection centre can be obtained from your

Municipality or from other competent local entities.

If you are replacing the old equipment with a new equivalent product, the distributor

must take-back the old equipment free of charge on a one-to one basis as long as the

equipment is of equivalent type and fulfilled the same functions as the supplied

equipment.

Your rôle in participating to the separate collection of waste of electric and electronic

equipment is essential to ensure that environmental protection and human health

objectives connected to a responsible treatment and recycling activities are achieved.

PS.: The above mentioned information are reported herewith in compliance with

Directive 2002/96/CE, which requires a separate collection system and specific

treatment and disposal procedures for the waste of electric and electronic equipments

(WEEE). For further and more detailed information, we invite you to visit our website at

www.atlantis-land.com

Page is loading ...

Atlantis Land S.p.A.

Viale De Gasperi, 122

20017 Mazzo di Rho (MI)

E-Mail: [email protected]

WWW: http://www.atlantis-land.com

Atlantis A05-17AM-L02, S 173 User manual

Related papers

Other documents