ATEN PE5342TG User manual

21/24/42-Outlet eco PDU

PE5221T / PE5224TA / PE5324T / PE5342T

User Manual

www.aten.com

PE5T User Manual

ii

EMC Information

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT:

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

The device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

CE Warning: This is a class A product. In a domestic environment this product may

cause radio interference in which case the user may be required to take adequate

measures.

RoHS

This product is RoHS compliant.

SJ/T 11364-2006

The following contains information that relates to China.

eco PDU User Manual

iii

User Information

Online Registration

Be sure to register your product at our online support center:

Telephone Support

For telephone support, call this number:

User Notice

All information, documentation, and specifications contained in this manual are subject

to change without prior notification by the manufacturer. The manufacturer makes no

representations or warranties, either expressed or implied, with respect to the contents

hereof and specifically disclaims any warranties as to merchantability or fitness for any

particular purpose. Any of the manufacturer's software described in this manual is sold

or licensed as is. Should the programs prove defective following their purchase, the

buyer (and not the manufacturer, its distributor, or its dealer), assumes the entire cost of

all necessary servicing, repair and any incidental or consequential damages resulting

from any defect in the software.

The manufacturer of this system is not responsible for any radio and/or TV interference

caused by unauthorized modifications to this device. It is the responsibility of the user

to correct such interference.

The manufacturer is not responsible for any damage incurred in the operation of this

system if the correct operational voltage setting was not selected prior to operation.

PLEASE VERIFY THAT THE VOLTAGE SETTING IS CORRECT BEFORE USE.

If any bodily injury or property damage with respect to operation of the product results

from users not having installed the product in accordance with the instructions provided

in the product’s user manual, or the product is used in an environment with a current

load over the designed specifications of the product, ATEN is not liable for any loss or

damage.

International http://eservice.aten.com

International 886-2-8692-6959

China 86-10-5255-0110

Japan 81-3-5615-5811

Korea 82-2-467-6789

North America 1-888-999-ATEN ext 4988

United Kingdom 44-8-4481-58923

PE5T User Manual

iv

PE Device Safety Notice

 Set the maximum permissible breaker protection in the building circuitry to the

current rating specified on the rating plate. Observe all national regulations and

safety codes as well as deviations for breakers.

 Only connect the PE Device to a grounded power outlet or a grounded system!

 Make sure that the total current input of the connected systems does not exceed

the current rating specified on the rating plate of the PE Device.

 There is a risk of explosion if the battery is replaced with an incorrect type.

Dispose of used batteries according to the relevant instructions.

eco PDU User Manual

v

Package Contents

The eco PDU PE Series package consists of:

1 PE5221T / PE5224TA / PE5324TA / PE5342TB / PE5342TG Power

Distribution Unit

1 Power Cord (PE5221T / PE5224TA only)

1 Mounting Kit

1 User Instructions*

Check to make sure that all of the components are present and in good order.

If anything is missing, or was damaged in shipping, contact your dealer.

Read this manual thoroughly and follow the installation and operation

procedures carefully to prevent any damage to the switch or to any other

devices on the eco PDU installation.

* Features may have been added to the eco PDU since this manual was

published. Please visit our website to download the most up-to-date version.

Manual Date: 2016-01-29

All other brand names and trademarks are the registered property of their respective owners.

PE5T User Manual

vi

Contents

EMC Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

SJ/T 11364-2006 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii

User Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Online Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Telephone Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

User Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii

PE Device Safety Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x

Chapter 1.

Introduction

Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Comparison Chart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Power Distribution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Remote Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

eco Sensors Energy Management Software*. . . . . . . . . . . . . . . . . . . . 5

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Sensors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Cable Holders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PE5221T Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

PE5224TA Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

PE5324TA Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

PE5342TB Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

PE5342TG Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Readout Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Chapter 2.

Hardware Setup

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

PDU Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Securing the Cables / Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Securing the Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

eco PDU User Manual

vii

Chapter 3.

Basic Operation and

First Time Setup

Operation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Browser. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

eco Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

First Time Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Network Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Changing the Administrator Login. . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Moving On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Chapter 4.

Browser Operation

Logging In . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

The eco PDU Main Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Page Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Energy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

User. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Administrator Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

The System Log Event List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Notification Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Device Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Login Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

Working Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Session Timeout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Account Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Login String / IP Filter / Mac Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Authentication & Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Private Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

PDU. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Firmware File. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

Backup/Restore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Appendix

Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

The eco PDU’s Main Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

PE5T User Manual

viii

Securing the Power Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Technical Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

North America. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

IP Address Determination. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

PE5221T(B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

PE5221T(G) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

PE5221T(J). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

PE5224TA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

PE5224TA - Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

PE5324TA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

PE5324TA - Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

PE5342TB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

PE5342TB - Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

PE5342TG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Administrator Login Failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

eco PDU User Manual

ix

About This Manual

This User Manual is provided to help you get the most from your eco PDU

system. It covers all aspects of installation, configuration and operation. An

overview of the information found in the manual is provided below.

Chapter 1, Introduction, introduces you to the eco PDU system. Its

purpose, features and benefits are presented, and its front and back panel

components are described.

Chapter 2, Hardware Setup, provides step-by-step instructions for setting

up your installation.

Chapter 3, Basic Operation and First Time Setup, explains the

procedures that the Administrator employs to set up the eco PDU network

environment, and change the default username and password.

Chapter 4, Browser Operation, describes how to log in to the eco PDU

with an Internet browser, and explains the layout and components of the eco

PDU’s user interface.

An Appendix, provides specifications and other technical information

regarding the eco PDU.

PE5T User Manual

x

Conventions

This manual uses the following conventions:

Product Information

For information about all NRGence products and how they can help you save

money in the data center, visit NRGence on the Web or contact an ATEN

Authorized Reseller. Visit ATEN on the Web for a list of locations and

telephone numbers

 International – http://www.aten.com

 North America – http://www.aten-usa.com

Monospaced Indicates text that you should key in.

[ ] Indicates keys you should press. For example, [Enter] means

to press the Enter key. If keys need to be chorded, they

appear together in the same bracket with a plus sign

between them: [Ctrl+Alt].

1. Numbered lists represent procedures with sequential steps.

♦ Bullet lists provide information, but do not involve sequential

steps.

→ Indicates selecting the option (on a menu or dialog box, for

example), that comes next. For example, Start

→ Run

means to open the Start menu, and then select Run.

Indicates critical information.

1

Chapter 1

Introduction

Overview

As part of its NRGence line, ATEN has developed a new generation of green

energy power distribution units (PDUs) to effectively increase rack space and

the efficiency of data center power usage. The NRGence PE5221T /

PE5224TA / PE5324TA / PE5342TB / PE5342TG eco PDUs are thin form

factor intelligent PDUs that contain 21/24/42 AC outlets and are available in

various IEC or NEMA socket configurations.

Thin form factor PDUs have a smaller 56 mm width to fit tight into server racks

providing more space for cooling and maintenance. The smaller design leaves

8% more space in the server rack to increase air flow and cool IT equipment

more efficiently. For full racks this means faster maintenance with easier

access to equipment installed behind PDUs.

They provide secure, centralized, intelligent, power monitoring at the PDU or

bank level with the ability to monitor the health of the data center's

environment via sensors*. The basic characteristics of each model are shown

in the table on page 3.

The NRGence eco PDUs offer real-time power measurement and threshold

alerts – allowing you to monitor the PDU’s power status, bank status and

circuit breakers*, either at the PDU device or from practically any location via

a TCP/IP connection*.

Installation and operation is fast and easy: plugging cables into their

appropriate ports and user-friendly browser-based configuration and

management is all that is entailed. Since the eco PDU firmware is upgradeable

over the Net, you can stay current with the latest functionality improvements

simply by downloading updates from our website as they become available.

NRGence eco PDU supports any 3rd party V1, V2, V3 SNMP Manager

Software and NRGence eco Sensors (eco PDU Manager Software). eco

Sensors provides you with an easy method for managing multiple devices,

offering an intuitive and user-friendly Graphical User Interface that allows you

to configure a PDU device and monitor power status of the equipment

connected to it.

The thin form factor series of ATEN PDUs have a circuit breaker alert that can

sound an alarm and send SNMP trap or e-mail alerts when a trip occurs. This

PE5T User Manual

2

feature provides a faster response time to recover servers and other devices

when a circuit overload causes a loss of power.

With its advanced security features and ease of operation, the eco PDU is the

most convenient, most reliable, and most cost effective way to remotely

monitor power and allocate power resources in the most efficient way possible.

Note: 1. Sensors are optional accessories. A sensor-enabled installation is

required to generate a more complete energy-efficient data and chart.

Higher sensor installation density is helpful to generate more accurate

data. See Optional Accessories, page 7, for further information.

2. Circuit breaker monitoring is only available on models with 30/32

amps.

3. eco PDUs are primarily designed for access via Intranets; extra

network security protection is suggested for Internet access usage.

Chapter 1. Introduction

3

Comparison Chart

Note: For the complete specifications of individual models, please reference

Specifications, page 65.

Model Inlet / Cord Outlets

Metering

Level

Amps

Per Port Total

PE5221T IEC 60320

20

21

18 x IEC320 C13

3 x IEC320 C19

PDU/

Bank

10A (Max),

16A (Max)

16A

(Max)

NEMA 6-

20p

21 PDU /

Bank

15A (Max)

12A (UL de-

rated), 20A

(Max) 16A

(UL de-rated)

20A

(Max),

16A (UL

de-rated)

NEMA L6-

20p

21 PDU /

Bank

15A (Max)

12A (UL de-

rated), 20A

(Max) 16A

(UL de-rated)

20A

(Max),

16A (UL

de-rated)

PE5224TA NEMA 5-

20P

24 24 x NEMA 5-

20R

PDU /

Bank

20A (Max),

16A(UL

de-rated)

20A

(Max),

16A (UL

de-rated)

PE5324TA NEMA L5-

30P

24 24 x NEMA 5-

20R

PDU/

Bank

15A (Max),

12A (UL

de-rated)

30A

(Max),

24A (UL

de-rated)

PE5342TB NEMA L6-

30P

42 36 x IEC320 C13

6 x IEC320 C19

PDU /

Bank

Per C13

Duplex

Receptacles:

15A (Max),

12A (UL

de-rated);

Per C19

outlet: 15A

(Max), 12A

(UL de-rated)

30A

(Max),

24A (UL

de-rated)

PE5342TG IEC 60309

32A

42 36 x IEC320 C13

6 x IEC320 C19

PDU /

Bank

Per C13

Duplex

Receptacles:

10A; Per C19

outlet: 16A

32A

(Max)

PE5T User Manual

4

Features

Power Distribution

 Thin Form Factor design with 56 mm width

 Space saving 0U rack mount with rear mounting

 IEC or NEMA outlet models

 3 digit 7-segment front panel LED shows PDU/Bank current/IP address

 Remote users can monitor PDU / Bank status via web pages on their

browsers

 2 16A slim breakers (PE5342T and PE5324T models only)

 Safe shutdown support

 Separate power for the unit's own power and its power outlets. The user

interface is still accessible even when an overload condition trips the

devices' circuit breaker

 Supports button mount on the rear of the PDU for easy installation

Remote Access

 Remote power control via TCP/IP and a built in 10/100 Ethernet port

 Network Protocols: TCP/IP, UDP, HTTP, HTTPS, SSL, SMTP, DHCP,

NTP, DNS, auto sense, Ping

 eco PDU Power Management software – eco Sensors

 Supports SNMP Manager V1, V2 & V3

Operation

 Supports multiple power control methods – Wake on LAN, System after

AC Back, Kill the Power

 Easy setup and operation via a browser-based user interface

 RTC support to keep the timer running during times of no power.

 Up to 8 user accounts and 1 administrator account.

Management

 Power status measurement at the PDU/Bank level*

 LED indicators for PDU and Bank current and IP address at the PDU

Chapter 1. Introduction

5

 Real-time aggregate current, voltage, and power and power dissipation

displayed in a browser-based UI for monitoring at the PDU level and at the

bank level*

 Environment monitoring – supports external temperature / humidity /

differential pressure sensors for rack environment monitoring

 Circuit breaker alert sounds an alarm and sends SNMP trap or e-mail alerts

when a circuit breaker trips*

 Current and voltage threshold setting

 Naming support for outlets

 User outlet access assignment on an outlet-by-outlet basis.

 Event logging and syslog support

 Upgradeable firmware

 Multi-language support: English, Traditional Chinese, Simplified Chinese,

Japanese, German, Italian, Spanish, French, Russian, Korean, Portuguese.

Note: Circuit breaker and bank level monitoring only available on 30A/32A

models.

Security

 Two-level password security

 Strong security features include strong password protection and advanced

encryption technologies – 128 bit SSL

 Remote authentication support: RADIUS

eco Sensors Energy Management Software*

 Automatic discovery of all PE devices within the same Internet

 Remote real-time power measurement and monitoring

 Real-time environment sensor monitoring

 Plotting/monitoring of all PE devices

 Exceed threshold alert through SMTP and System log

 Power Analysis report

Note: eco Senors is designed to work with NRGence PDUs and is bundled

with all PE series packages.

PE5T User Manual

6

Requirements

 Browsers accessing the eco PDU unit must support SSL 128 bit

encryption.

 For cold booting of attached computers, the computer's BIOS must

support Wake on LAN or System after AC Back.

 For Safe Shutdown:

 The computer must be running Windows (Windows 2000 or higher) or

Linux.

 The Safe Shutdown program (available by download from our website

or on the software CD included), must be installed and running on the

computer.

Chapter 1. Introduction

7

Optional Accessories

Sensors

Sensors are optional accessories. You can use the eco PDU unit without

sensors. However, if you want to have complete energy management of an

instrumented data center with the use of the eco PDU, you would need to use

eco Sensors software and install 4 sensors for each of the racks to generate a

complete energy-efficient data and chart. Higher sensor installation density is

helpful to generate more accurate data. 24/40 -port models have 2 sensor ports.

In this case, Sensor 1 needs to be installed at the intake of the rack and sensor

2 needs to be placed at the exhaust of IT equipment of the rack. A sensor-

enabled installation is required to generate a more complete energy-efficient

data and chart. Higher sensor installation density is helpful to generate more

accurate data. Available sensors are show in the table, below:

Sensor Management

Sensors can be managed via the eco PDU’s built-in graphical user interface

(GUI) or with the NRGence eco Sensors software that can be downloaded from

the ATEN website. The download link can be found on the software CD

provided with the eco PDU package.

Cable Holders

Cable holders are optional accessories. For added safety, use ATEN Lok-U-

Plug cable holders and EZ-Lok Plug Connectors to secure the cables from your

attached devices in place on the eco PDU unit. Use only the ATEN Lok-U-Plug

cable holders and EZ-Lok Plug Connectors that have been specifically

designed to work with the eco PDU. Using any other kind of cable securing

device could be highly dangerous.

Sensor Part Number

Temperature EA1140

Temperature / Humidity EA1240

Differential Pressure / Temperature EA1340

Part Number Description

2X-EA07 Lok-U-Plug Cable Holder (10 pcs)

2X-EA08 Lok-U-Plug Installation Tool (4 pcs)

2X-EA10 C14 EZ-Lok Plug Connector

2X-EA11 C20 EZ-Lok Plug Connector

PE5T User Manual

8

Components

PE5221T Front View

2

5

1

3

4

Chapter 1. Introduction

9

Note: Holes for ATEN Lok-U-Plug cable holders are located around the

outlets. See Securing the Cables / Plugs, page 23, for further

information.

No. Item Description

1 Power Inlet The power cord that connects the unit to an AC

power source plugs into this IEC 60320 C20

socket.

2 Power Outlets* 21 in total (18 x IEC320 C13 + 3 x IEC320 C19)

3 Sensor Ports External sensors plug into these two RJ-11 ports.

4 LAN Port and LEDs The cable that connects the eco PDU to the LAN

plugs in here. The Link and LAN LEDs are built

into the LAN port:

Link: Lights GREEN to indicate that a connection

via the eco PDU's RJ-45 Ethernet port has been

established. Flashes to indicate data is being

transmitted.

LAN: Lights ORANGE to indicate 10 Mbps data

transmission speed. The LED lights GREEN to

indicate 100 Mbps data transmission speed.

5 Readout Section, LEDs

and Reset Switch

Details of this section are provided on page 18.

PE5T User Manual

10

PE5224TA Front View

2

5

1

3

4

Page is loading ...

ATEN PE5342TG User manual

This manual is also suitable for

ATEN PE5342TG User manual

Related papers

Other documents