Genie 36280S Owner's manual

Brand: Genie

Model: 36280S

Category: Garage Door Opener

Type: Owner's manual

This manual is also suitable for

Operation and

Maintenance Manual

3628336241

TABLE OF CONTENTS

Warranty Information ................... 2

Safety Information ..................... 3

Safety Features ......................... 3

Important Installation Instructions ....... 3

Pre Installation Checklist .............. 46

Adjustments .......................... 7=8

Programming the Remote Control ..... 89

Installing Lightbulb and Lens ............ 9

Scheduled Maintenance ............... 10

Troubleshooting Guide ............. 1011

Wiring Diagram ........................ 12

Parts Lists and Exploded Views ...... 1213

Accessories ............................ 14

COMPLETE WITH mNTELLlCODE

REMOTE CONTROL AND SERIESli

For up to 7'-6" tall Doors. (Extension Kit avaimable for 8' Doors)

included Wail Control MUST be installed prior to Operation of

this Garage Door Operator.

Safe-T-Beam ®Safety Reverse System Must be installed and

the Force Controls MUST be Properly Set to close door.

This Equipment meets or exceeds all Federal, State and UL325

THEGEN|ECOMPANYLIMITEDWARPJ ,NTY

What iscoveted?

Any defect [n material and product workmanship from personal,normal

household use [naccordance with the Owner's Manual.

For how long?

MODEL2560... 1Syears on motor, 3years all other parts.

MODEL3560... Lifetime' on motor,3 years allother parts.

%[fedme=Aslong dsyou ownyour home.

Who gets the warranty?

This warranty is limited to the consumer who originally purchased

the product.

Geographic scope:

This warranty applies only to units installed and operated within the country

where they were purchased.

Limitations:

IMPLIEDWARRANTIES,INCLUDINGTHOSEOFFITNESSFORA PARTICULAR

PURPOSEANDMERCHANTABILITY(ANUNWRITTENWT_RRANTYTHATTHE

PRODUCTISFITFORORDINARYUSE)ARELIMITEDTOONEYEARFROMTHE

DATEOFPURCHASE.GENIEWILL NOTPAYFOR:LOSSOFTIME;

INCONVENIENCE;LOSSOFUSEOFYOURGENIEPRODUCTORPROPERTY

DAMAGECAUSEDBYYOURGENIEPRODUCTORITSFAILURETOWORK;ANY

SPECIAL,INCIDENTALORCONSEQUENTIALDAMAGES;ORANY DAMAGES

RESULTINGFROMMISUSEORMODIFICATIONOFYOURGENIEPRODUCT.

Somestatesand provinces do not allow limitations on how long animplied

warranty lasts or the exclusion of incidental or consequential damages,sothe

above limitations or exclusionsmay not apply to you.

This warranty isthe only one we will give onyour Genieproduct, and it sets

forth allour responsibilities regarding your Genie product.There arenoother

expresswarranties.

Stateand province rights:This warranty givesyou specificlegal rights,andyou

mayalso have other rights which vary from stateto state and province to

province.

How to get warranty service:

To obtain warranty servicefor your Genie product, you must provide proof of

the dateand placeof purchaseof the product.

1.Do-It=Yourself-Service.

Callthe Genie Customer Servicetoll free at 1.800.354.3643to speak in

person to atrained Genie representative for assistancein diagnosing the

problem and arranging to supply you with the required parts for do-it-

yourself repairs.Trained servicerepresentatives areavailable Monday-Friday,

8:00a.rn.- 9:00 p.m.,EasternTime,and on Saturday,10:00a.m.to 7:00 p.rn,

EasternTime (subject to holidays)You may alsoget the information you

needat www.geniecompony.com.

2,Service From Authorized Dealers.

YoualsomayobtainwarrantyservicefromGenieauthorizeddealersbycallingthe

GenieCustomerServiceat1.800.354.3643or byvisitingw_geniecomporry.com

beforeschedulingwarrantyservice.Ifwarrantyserviceisprovidedby anauthorized

dealer,Geniewilt provideallrequiredpartsunderwarrantyat nochargetoyou,but

thedealersareindependentbusinesspeopleandmayrenderabenchor servicecall

chargeforthek services.Geniewill notreimburseyouor otherwiseberesponsiblefor

thosecharges.

Wesuggestthatyouretainyouroriginalpackingmaterialintheeventwechooseto

repairor replaceyourGenieProductandrequestthatyou shipitto us.Besureto

includeyourname,address,telephonenumber,proofofdateandplaceofpurchase

andadescriptionof theoperatingproblem.Afterrepairingor replacing,yourGenie

product,wewillshipit toyourhomeatnocostto youfor partsandlabor,butyouwill

haveto payaminimumof$5.00for shippingandhandlingcharges.

Yourchoiceofeitheroneoftheabove-describedserviceoptionsisyourexclusive

remedyunderthiswarranty.

What this warranty does not cover:

Thiswarrantydoesnotcoverbatteries(whichareconsideredreplaceableparts),

installation,commercialuse,defectsresultingfromaccidents,damagewhilein transitto

ourservicelocationor damageresultingfromalterations,misuseorabuse,lackofproper

maintenance,unauthorizedrepairor modificationoftheproduct,affixingofany

attachmentnotprovidedwiththeproduct,programmingof theRemoteControl

Devices,Safe-T-Beam®adjustment/cleaning,staplesthroughwiring,pinchedor broken

wires,Carriagedisengaged,ForceContro!adjustments,dooroutof balance,broken

springsorcables,poweroutages,useofextensioncords,missingor damagedpartson

discounted,clearanced,finalsaleortaped cartons,phantomoperations(laborisnot

coveredifOpenerisfunctioning properlywhiletechnicianisin garage),fire,flood,or

actsofGod,or otherfailureto followtheOwner'sManual

Pleasenote the following information,soit isavailable if you

need to call us.

Date Purchased / /

Serial Number

Operator Model

Remote Control Model

Model Number and

Serial Number are

located on front panel

inside the lens,

jj_

}

WK YR P [

27 94 4 H

Serial/Mfg No.

Pleasekeep original or photocopy ofyour sales receipt

with this manual for future reference should service

ever be requiredo

INCLUDEDIN THIS PACKAGE

Manual 1)Warranty Information

2) Pre Installation Checklist to be reviewed prior

to any assembly or installation

3) Necessary Adjustments

4) Programming Remote Devices

5) Maintenance and Troubleshooting

6)PartsExplosions

7)AccessoryOrderForm

8) Door Opener Association Safety and

Maintenance Brochure (DASMA)

9) Entrapment Warning Label =To be Adhered in

close proximity to wall control

Poster 1) Pictorial and step by step opener assembly

instructions

2) Pictorial and step by step opener installation

instructions

iT IS CRITICAL THAT ALL SAFETY WARNINGS

MARKED CLEARLY [N BOTH THE MANUAL

AND POSTER ARE READ, UNDERSTOOD AND

FOLLOWED.

Visit Our Website at: www.geniecompany.com

FORANSWERS,"CALL 1,800,354,3643

SAVETHESE INSTRUCTIONS

2 For Help, call 1=8OO-35-GENIE or visit www.geniecompanyocom

OVERVIEW OF POTENTIAL HAZARDS

Overhead doors arelarge,heavy objectsthat movewith the help ofsprings under high tension and electric motors. Sincemoving objects,springsunder

tension,and electric motors can causeinjuries,your safetyand the safetyof others depend onyou reading the information in this manual. Ifyou have

questions ordo not understand the information presented,callTheGenie Company.or your localGenie Distributor.

Hnthis section, and those that follow, the words Danger, Warning and Caution are used to emphasize important safety

information. The word:

_, DANGER; indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

A WARNING; indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

A CAUTION; indicates a potentially hazardous situation which, if not avoided, may result in injury or property damage.

The word NOTE is used to indicate important steps to be followed or important considerations.

POTENTIALHAZARD

MOVINGDOOR

ELECTRICALSHOCK

HIGHSPRINGTENSION

EFFECT

WARNING:

Could result in death

or serious injury.

WARNING:

Could result in death

or serious injury.

WARNING:

Could result in death

or serious iniury.

PREVENTION

Keep people clear of opening while door is moving.

oDo Not allow children to play with the door operator.

Do Not operate a door that jams or one that has a broken spring.

oTurn off power before removing operator cover.

oWhen replacing cover, make sure wires are not pinched or near

mowng parts.

oOperator must be properly grounded.

oDo Not try to remove, repair or adjust springs or anything to

which door spring parts are fastened, such as,wood blocks,

steel brackets, cables or other like items,

oRepairs and adjustments must be made by a trained door

system technician using proper tools and instructions,

MPORTANT INSTALLATION

NSTRUCTIONS

zLWARNING:

TO REDUCETHERISKOFSEVEREINJURYOR DEATH:

1 READAND FOLLOW ALL SAFETY.INSTALLATIONAND

OPERATIONINSTRUCTIONS.If you have any

questions or do not understand an instruction, call

your authorized Genie installation professional.

2 Do Not install operator on an improperly balanced

door. Animproperly balanceddoor couN cause

severe injury. Repairs and adjustments to cables,

spring assembly, and other Hardware must be made

by a trained service person using proper tools and

instructions.

3 Remove all ropes, and disable all locks connected to

the door before installing operator.

4 tnstall door operator 7 feet or more above the floor.

Mount the emergency release knob 6 feet above

the floor.

5 Oo Not connect the operator to the source of power

until instructed to do so.

5 Locate the control button:

[ Within sight of door,

At a minimum height of,5 feet so small children

cannot reach it_

, Away from all moving parts of the door.

7 Install the entrapment WARNING labet next to the

wal button or console. Install the emergency release

tag on, or next to, the emergency release

8 The operator must reverse when the door contacts a

1-1/2 inch high object on the floor at the, cen!er of

the doorway[Thisisaboutthe sizeof a2 x 4 board

laid flat.

SAFETY FEATURES

Safe-T-Beam ® (STB) Non-Contact Reversing System

Places an invisible beam across door opening, that reverses

the door during down travel to the fully open position if

anything passesthrough beam.

Safe-T-Reverse ® Contact Reversing System

Automatically stops and reverses a closing door within 2

seconds of contact with an object.

Safe-T-Stop ® Timed Reversed System

Automatically opens a closing door, if door does not close

within 30 seconds,

ForceGuard ® Control

Used to set the force required for opening and closing

door. For maximum safety, set the minimum force required

to fully open and close door.

Automatic Lighting System

Light bulbs up to 60 Watts max., used for safer entries and

exits, The lights turn on when door isactivated and

automatically turn off 4,5 minutes later.

Manual Emergency Release

Allows the garage door to be opened or closed manually

for emergencies or maintenance,

For Help, ca!l 1-800-35-GENIE or visit wwwogeniecompany,¢ora 3

PRE-INSTALLATiON CHECKUST

This Opener includes parts and supplies needed to install in most

garagesand connect to most garage doors. There aremany variations

of garages and garage doors, A few additional parts and supplies may

be needed to install Opener into your garage and connect to your

garage door. While checking items listed below, note any additional

items you will need,

Tools used in this section:

12'+Tape Measure • Pendl • Ladder • Level

Check following items before assembling Opener:

CHECK DOOR CONDiTiON AND

THICKNESS

Checkcondition of vertical stile in center of door, and its connection to

door's top and bottom beams. (Figure 2)

A If door frame isnailed together and not asolid connection, door

frame must be braced or reinforced before installing Opener,

B If door is'lightweight" (made with frame and skin- not solid),

door (including door frame) must be braced or reinforced before

installing Opener.

C Adoor opener reinforcement bracket may also be needed to

connect garage door to Opener's Door Bracket.This Opener is

designed for instalIation on a proper{y braced sectional door or

solidly braced one-piece door.

D Contact your Genie FactoryAuthorized Dealeror dealer of your

garage door for any necessarybracing and adoor opener

reinforcement bracket (if needed) before proceeding.

E If you have awooden door, measuredoor's thickness.If your door

islessthan 2"thick, brace door or useshorter Door Bracket LagScrews

(1/4" x I-I/4" - not included)

CHECK GARAGE DOOR

ALIGNMENT_ OPERATION_

AND BALANCE

A Raisedoor, check alignment and seeif it movesfreely (Figure 1). If

door appearsout of alignment, binds,or does not move smoothly,

contact aGenie Factory Authorized Dealeror dealer of your garage

door for repairs and adjustments to door mechanism,

B Raisedoor to 3' - 4' above ground and carefully let go, Door

should stay stationary. Slight movement is acceptable, More than

slight movement means door isout of balance, Contact a Genie

FactoryAuthorized Dealer or dealer of your garage

door for repairs and adjustments to door mechanism,

KEEPFEET CLEAR OF DOOR

Sectional _ _q--_j'_ One-Piece

Door _ - Door

Figure 1 Checking door balance

C Checkdoor type. Make a note of whether it isasectional or a one-

)iecedoor for referencelater (Figure 2).

Ifyour door Sticks,binds,or isout of balance,have it adjusted

bya Genie Factory Authorized Dealer. Door springs,cables,

pulleys, brackets and associatedhardware are under extreme

tension and can Causeserious injury or death.

SECTIONAL DOOR, TORSION SPRINGS SECTIONAL DOOR, EXTENSION SPRINGS

J'_;:>" Extension

Center "::::-_] :: I]

q_:]]

ONE-PIECE DOOR, TRACKLESS

Header Area

Center Stile

Figure 2 Note DoorType

MEASUREGARAGEDoor HBGHT

Measuredoor height (floor to top of door) using atape measure.

This new GarageDoor Opener isdesigned for doors up to and

including 7'6" tail.Ifdoor height is 7'6" or lesscontinue to CheckStep 4.

C Ifdoor height is8'-0'_you need a RailExtension Kit.(Figure 3).

(SeeAccessoriesOrder Form,Page14).

D Ifthe door height istaller than 8'-0",the opener you purchased is

the wrong version.Contact your Customer ServiceRepresentative

at 1-800-354-3643.

E×,eos oofor

8"door

@m-- _ ---e

l__ Figure 3 Rail Extension Kit

CHECK DOOR HEADER AREA

The header is a heavily reinforced section of the wall just

above the top of the garage door opening.

A Findvertical center line of door and header:

Closedoor.

Measuredoor width at top.

Marka point atcenter of door and on header directly

above door. Drawa center line to connect points.

B FindHeader Bracket mounting height (Figure 4): (Donot attach

Header Bracket).

Raisedoor,watching top edge of door and stop door

when its edge reachesits highest point.

Measuredistance ("H") from top edge of door to floor.

Forsectional doors, add2-1/2" to "H': Marka point

on center line. Bottom of Header Bracket wiII be

installed here.

Forone-piece doors, add 6"to'H': Mark this point on

center line. Bottom of Header BracketwiII be

installed here.

SECTIONAL DOOR ONE-PIECE DOOR

H+24/2"_ _ H+d"

/ 7

HEADER _IEADER

Figure 4 Find Highest Point of Trave[

4 For Help, call 1-800-35-GENIE or visit www, geniecompanyocom

o Foralltypesand stylesof doors:

- ff the ceiling ,inyour garage is so low that there is

not at least a 3 space above the Header Bracket

mountingpolnt, contact a Genie Factory

AuthorizedDealer.

If a door spring isin the way, place the Header Bracket

above the spring. Do Not move the door spring.

Door springsareunder extremely hi

should be handled ONLYby a trained professional. I

C Checkwall for astud or a solid header at your mark: (Ifchecking a

finished waJi,astud finder may be helpful).

, If location isabove Header,a 2" x 6"board must be

screwedto studs beside your mark with at least two Lag

Screwsand Flat W'ashers(not provided).

Transferyour markto new mounting board.

CHECK POWER HEAD

MOUNTING AREA

Check ceiling or space above where Opener Power Head will be

mounted (Figure 5): There must be a 120Volt grounded outlet or

wiring box within 3feet of Power Head.

outlet

(7'-6"door

Door Center Line

Figure 5 Check Power Head location

A The measurements above aretaken from the garagedoor

centerJinetoward the rear of the garage.

B Findlocation of ceiling joist or truss above where Opener Power

Headwill be and estimate type and quantity of materials needed for

your installation (Figure 5A & B).

MOUNTING EXAMPLES

Perforated Angle Iron Conduit

Figure5A

OPENCEILINGSStrapsand angle iron may attach directly to joists

or trusses.

Wood

For HeJp, can 1-800-35-GENIE or visit www,geniecompany,¢om

Perforated Straps

FiNiSHEDCEILINGS

Locateceiling joists or trussesusing

astud finder or similar device.

Attach angle iron(not included) to

joistsor trussesthrough finish

material using Lag Screws.

Figure6B

CHECK CEmLmNG FOR GROUNDED

PowER SOURCE

A Checkthat there is a 15Amp 120Volt grounded electrical

outlet or grounded permanent wiring box (per building code)

within 3'of Opener Power Head:Figure 5

• If not, an outlet or wiring box must be installed. Contact

alicensed electrician for installation.

• If building codes require permanent wiring, Power Head

must be partially disassembled to install appropriate

wiring in placeof PowerCord. (SeeAssemblyand

Installation Poster.)

Permanent wiring must be installed by a Licensed

Emectri¢ian. Not all Genie Factory Authorized Dealers

are Licensed Electrician's. Contact someone who isa

Licensed Electrician.

WARNING •

Do Not use an extension cord! Extension cords can

De Net use portable generator! This product is

designed to operate using standard house current.De

Not use alternate power supplies,

MOUNTmNG BRACKET LOCATmON

Check for wood garage frame, jamb, or masonry at mounting

[ocation (6" above floor) with attachment tabs facing away

from garage door (Figure 7L

A If you cannot mount Safe-T-Beam_ Mounting Bracket to

wood frame:

Concrete screws and concrete anchors (not incHuded)

must be used to mount Brackets on masonry with

attachment tabs facing away from garage door.

Source

Sensor .,d_-,

, _-

Safe-T-Beam® _ Top of

Mounting Brack_/_ !.. Bracket @'above

Figure,Mount,ng

Safe_T_Beam® _ floor

Components

RECOMMENDED TOOLS

Tools (Figure 8):

Additional took to make installation easier:

Slotted and phi[Hps screw=driver bits

Stud finder

Sheebmeta[ cutting snips

REMOVE EXISTING GARAGE

Door LocKs

Check that the garage door locks, rope, and T-Handles are

removed from the garage door before starting the instaHHation.

A ffyour garage does not have a separate entry door, it is

highHy recommended to install[ aGenie Emergency Release Kit

(GER-2). Emergency Release Kit lets you open the garage door

from outside if there is apower failure. (Please see Accessories

Order Form on page 14.)

Before going further, get any items and tools if needed

for your installation

_7 Garagedoor frame reinforcement brackets,screws,bradng

or reinforcement kits (dealer)

_7 Lag Screws(1-1/4")for a wood door lessthan 2" thick (store)

_7 Electricaloutlet and/or wiring (supplied byalicensed electrician)

_7 Sufficient angle iron or strapping for hanging PowerHead (store)

_7 60Wan light bulbs (Rough servicebulbs recommended)(store)

_7 GER-2EmergencyReleaseKit for entry during power failure (store)

_7 Wood for header,ceiling, and/or door braces (store)

_7 Masonry fastenersfor Safe-T-Beam€:'Bracket installation (store)

_7 Safe-T-Beam_"BracketExtensions (dealer)

_7 Masonrydri[[ bit (store)

_7 Extension Kit (for 8'Garage Doors)(dealer)

Go to Assembly and Installation Poster for full

Installation Instructions,

I/t6" 5/32" Tape Measure_

DriH Bit DriH Bit

6' or 7'

Step Ladde_

Wire Phi[bps Screwdriver

Stripper

AdjustaMe Wrench FUat BUade Screwdriver

Hammer Safety, GUasses r/l_ _-_

PenciU

1/4" 5/16" 3/8" 7/16" I/2" 9/16"

Sockets

Hack Saw Wrench

IMPORTANT

SAFETY INSTRUCTIONS

SEVEREINJURY OR DEATH

1 READANDFOLLOWALLINSTRUCTIONS.

2 Neverletchildrenoperateor playwith the DoorControls,Keepthe

RemoteControlawayfromchildren.

3 Alwayskeepthemovingdoor in sightandawayfrom peopleand

objectsuntilthedoor iscompletelyclosed.

NOONESHOULDCROSS]HEPATHOFAMOVINGDOOR.

4 NEVERGOUNDERASTOPPED.PARTIALLYOPENDOOR.

5 TestOpenermonthly.Thedoo_MUSTreverseon contactwith

alq/2 highobject(ora2 x4 board[aidflat)atthecenterofthe

doorway'onthefloor. Afteradjustingeitherthe Forceorthe Limit

oftraveLretestthe DoorOpener.Failureto adjustthe Opener

properlymaycausesevereinjuryor death.

7 KEEPGARAGEDOORSPROPERL_BALANCED.SeeOwner's

Manual.An improperlybalanceddoor increasesthe riskof severe

injuryoFdeath. HaveaGenieFactoryAuthorizedDealermake

'epaksto cablesspringassembliesandotherhardware.

8 SAVETHESEINSTRUCTIONS.

NOTES, REMINDERS

Carpenter's LeveU

Figure 8 Recommended Tools

6 For Help, call 1-800-35-GENIE or visit www, geniecompanyocom

MAmNTENANCE AND ADJUSTMENTS

ADJUSTING LiMiT SWITCHES

AND FORCE CONTROLS

WARNING:

• A moving garage door can cause senous injury or death.

Keepthe path dear.

o Position the ladder to the side of the Power Head so it is

clear of aHmoving parts of the Opener and the door.

o Setthe door Opener to use the minimum force needed

to open the door,

A CLOSE ADJUSTMENT

On front pane[ of Power Head find adjusting screw

marked "CLOSE" (Figure MA-1).

, Gently turn screw counterclockwise until it stops.

- Very little force is required to turn adjusting screw.

PressWall Console to chose garage door.

- Observe if door stops at "CLOSE" limit switch.

(Figure MA-2). If door is fully closed--adjustment is

finished. Go to "OPEN" Adjustment.

- If door stops but is not fully closed,

a. Measure distance between bottom of door

and floor.

b. Move"CLOSE"Limit Switch that same distance

toward door.

- If door stops and/or reverses before reaching the

"CLOSE" Limit Switch

a. Slightly increase CLOSE Force setting (clockwise).

- If door reverses after contacting floor, move Limit

Switch toward Power Head.

- If door fails to move, check Safe=T=Beam®System. See

Troubleshooting Section, pages 10=] 1.

Tighten Limit Switch Set Screw. Do not over-tighten

(strip} Limit Switch Set Screw.

B OPEN ADJUSTMENT

On front pane[ of Power Head find adjusting screw

marked "OPEN" (Figure MA-1).

, Gently turn screw counterclockwise until it stops.

- Very little force is required to turn adjusting screw.

PressWall Console to open garage door.

- Observe if door stops at "OPEN" limit switch.

(Figure MA=2). If door is fully open--adjustment

is finished.

- If door stops but is not fully open,

a. Measure distance between bottom of door

top of door opening.

b. Move"OPEN"Limit Switch that same distance

toward Power Head.

- If door stops before reaching the "OPEN" Limit Switch

a. Slightly increase OPEN Force setting (clockwise).

- If door fails to move, see Troubleshooting Section,

pages 10=11.

Tighten Limit Switch Set Screw. Do not over-tighten

(strip) Limit Switch Set Screw.

, Cycle opener a few times to double check settings.

Repeat adjustment steps as necessary.

Little effort isrequired to turn the Force

Adjusting Knobs.

° Ifthe door stops moving while opening or

closing, adjust the Open Force or Close Force

Controls slightly clockwise (to slightly

increase the force) and retry the step.

. The Open Force and Close Force Controls are to

be set to the minimum force necessary to

ensure the door smoothly opens and

closes completely.

* Ensurethe Carriage Assembly isengaged and is

between the two Limit Switches before

operating the Opener.

FORCE

CONTROLS

Figure MA-1 Making Force Adjustments

OPEN

Figure MA-2 Making Force Adjustments

For Help, call 1-800-35-GENIE or visit wwwogeniecompany, com

f Transmitter Complance Statement

Transmitters comply with al United Statesand Canadian legal requirements asofthe date

of manufacture, No warranty is made that they comply with al UegaUrequirements of any

other jurisd'iclon. Iftransmitters are to be used in another country, the importer must

determine compUiancew4h any UocaUUawsand reguUatlonswhich may differ from United

Statesand Canadian requirements prior to use.

Los transmisores cumplen con todas UasregUamentadones UegaUesde los EstadosUnidos

ydeUCanad_,en Uafecha de fabricaci6n, Ninguna garantfa seda que cumplan con todas

as regamentaciones legalesde ninguna otrajudsdicci6n. Silos transmisores sevan a

utlizar err otto pais,el importador debe determinar sicumplen con las reglamentaciones

y leyeslocales que puedao serdiferentes alas reglamentadones de los Estados Unidosy

del Canada, antes de usar losmismos.

Les emetteurs sont conformes £ la r_gementation am@icaine et canadienne _compter

de leur date de fabrication, Aucune garantie n'est stipul@ indiquant qu'Is sont conformes

toutes les prescriptions juridiques d'autres autorit_s, Siles _metteurs sont utlis_s dans

d'autres pays,t incombe a I'importateur d'en d_terminer leur conformit_ aux lois et r_ges

locales pouvant diff@er de celes desCtats-Uniset du Canadaavant toute utlisation

desdits 6metteurs.

Sendeger£te entsprechen alen gesetzlchen Bestimmungen in den USA und Kanada zum

Zeitpunkt der Herstelung.Wir Obernehmen keine Gew£hr[eistung fijr die Einha[tung a[[er

gesetzlichen Bestimmungen in anderen Landem,Solen Sendeger£te in anderen L£ndern

eingesetzt werden, so mussder Importeur vor dem Gebrauch sicherstelen,dass die

Sendeger£te auch sokhen Iokalen Bestimmungen entsprechen, wekhe yon den

Bestimmungen der USAund Kanadasabweichen.

£,x,l)l {_II!II __iiI I £ I?._ £ I I I _IInI _kI_ 4-1 __lSi _t£1t,_l_111°

;017l?,_!20_1-_t-_)'#,_lo)[_1c@.]1t¢'o5)tI, BI tl&l_',(0 {_/IJ/E Y_,'L0 i)]_gR$]]Z)_

niEi_O]_]E_Eke-XJ_qlA_A_ U@ #q_xb_bA_o£8_slql _Ai ujq3_ _tL_E}£_£!£

SETTING CONTACT

REVERSE FUNCTION

Limit Switch and Force Adjustments must be completed

before checking the contact reverse function (Figure _A-3).

A Open garage door using

Wall Console, Figure _A-3

B Lay a 2" x 4" board fiat in center

of doorway.

C Close door using Wail Console.

Check that door stops and reverses

within 2 seconds after it

contacts board:

, if door does not reverse, decrease

Close Force until door reverses.

, If door still does not reverse,

move Limit Switch toward door.

E Check Safe-T-Beam ° System

operation:

, If beam is blocked, door will

not close.

2" x 4" board

hid fiat

ACCESSORIES

PROGRAMMING THE

REMOTE CONTROLS

, Each Remote Control must be programmed

separately.

° The Remote Controls will not cause the door

Opener to close the garage door if the Safe-T-

Beam®System is malfunctioning.

° When programminc) the Remote Controls, they

must be at least 24 from the Antenna Wire.

Ifthe red Learn Indicator Light blinks

approximately 4 times per second,

lrogramming hasstopped. If programming

as stopped, repeat the above steps.

Each Button on a 2 or 3 Button Remote Control

isfor a different Opener. You cannot use more

than one Button per Remote, per Opener.

° A maximum of seven Remote Controls or

Wireless Keypads can be stored into the

Receiver at one time. If a Remote Control

becomes lost,or if you want to delete a Remote

Control or Wireless Keypad, see To EraseAll

Receiver Memory."

A To program one Button of aRemote Control (Figure MA-4):

Locate Learn Button and Learn Indicator Light

on left side of Power Head (Figure _A-5),

Press and release Learn Button, Red Learn

Indicator Light will blink 2 times per second,

Press Remote Control Button once within 30

seconds, Red Learn Indicator Light will stay lit,

Press Remote Control Button again, Red Learn

Indicator Light will go out, indicating that

memory is stored,

Press Remote Control Button again and the door

will operate,

B Program each additional Remote using step A above

(up to seven),

To Erase AiJ Remotes from Power Head Memory

A Press and hold Learn Button on Power Head for 10

seconds or untl Learn Indicator Light goes out.

Memory is erased:

Program Transmitter/Receiver again as needed.

To Replace Remote Control Battery

A FOR NON-FLASHLIGHTMODELS

Pop offthe back of the transmitter,

- Use coin, pen, screwdriver or any similar device,

- Replace old Battery with new coin type battery,

Replace back of remote,

B FOR FLASHLIGHT MODELS

Slide open battery cover,

- Replace old Battery with new AAA battery,

Replace battery cover,

8 For Help, call 1-800-35-GENl£ or vBit wwwogeniecompanyocom

£ WARNING:

A moving garage door may cause senous injury or death.

o Keep people dear of opemng while door ismoving.

Do not allow children to play with the Remote Controls,

Ufthe Safety Reverse does mot work properly:

, Close the door and disconnect the Opener using the

Emergency Release Cord,

° Do not use the door Opener, Remote ControB, oJ

Wireless Keypad.

o Refer to the door and door Opener Owner's Manuals

before attempting any repairs.

Remote Control Operation

A Press Button on Remote Control Garage door wH[ move.

B Press Button again. Garage door wi[I stop:

The door automatically stops at the end of the open or

close cycle.

C Press Button again. Garage door will reverse.

iNSTALLLUGHTBULBSAND LENs

A Install two 60Watt light bulbs (not included) into Light

Sockets (Figure MA-6):

o Rough service,] 30Volt bulbs are recommended.

B Insert the hooks at the bottom of the Iens into the slots

provided in the front plate of the power head (Figure MA-7).

o Ftip Lensupand fasten with (2) #8-32x 3/8"Phi]]ips Pan

Head Screwswhere indicated.

U_ith Opener. Any 1

moth__pener to operate 1

mune_ stop_,orking. "

1 Button Compact Remote 3 Button Compact Remote

w/Docking Station w/Docking Station

Figure MA-4 Genie Remote Controls

Figure MA-6

Receiver Learn

Code Button

Receiver

(not to

scab)

Figure MA-5 Learn Code Button and indicator Light

Toprogram a Hemelink ®or CaJ'2U Device:

(This GDO is Home!ink _ end Car2U compotible)

o Follow the Home[ink_)or Car2Uinstructions in your car

owner's manual

Figure MA=7

For Help, call 1-8OO-35-GENIE or visit wwwogeniecompany,¢om

A Monthly:

Door springs and door hardware:

Oil door roller, bearings, and hinges using silicone

lubricant or light oil

DO not operatedooiautomaticai[y or manually if springs [

are broken. Contact a Genie Factory Authorized Deater for

service orcaH Customer Service at 1.800.35.6ENIE. 1

, BaHanceDoor.

- CHosedoor.

- ReleaseCarriage Assembly from Rail Assembly by pulling

the Emergency Release Knob towards the door.

- Raisedoor manually 3L 4' and verify' that door staysat

that position. See Check Step 2 on page 4.

When the door is 3' _4' above the ground, the door

should stay open. Slight movement is acceptable, ff

the door moves too much, contact a Genie Factory

Authorized Dealer for service or call Customer Service at

1-800=35-GENIE.

- Reattach CarnageAssemb[y to Rail Assembly:

a. Pull the Emergency Release Knob toward Power Head.

b. CHosedoor.

Contact ReverseTest.

- Perform Adjustment 2 on page 8.

WARNING:

If the door fails to reverse on contact with the board

adjust the Close Force Control as specified in Set Limit

Switches and Force Controls on page 7 & 8. If the Opener

still fails,contact a Genie Factory Authorized Dealer for

service or call Customer Service at 1-800-35-GENIE

B Yearly:

Wipe off oid excess Hubdcant from Drive Screw.

Lubricate Drive Screw with Genie Lubricant GLU-3_

UseONLYGenieLubricant(6LU-3). Other lubricants

may damage the Opener.

GLU-3

Lubricant

FCC AND [C CERTIFIED

this device must accept any interference received, indud

ins interference that may cause undesired operation.

C As needed

Replace lightbulbs.(See page 9)

Safe-T-Beam ® System Self-Diagnostic Troubleshooting

Source {Red LED) Sensor {Green LED} Possible Problem solution

ON ON Normal operation None required

• Power Head not powered o Check breakers, fuses, plugs

OFF OFF

• Wiring from Power Head bad • Check wiring for obvious shorts

OFF ON • Wiring to Source missing or bad • Check wiring

• Power has been interrupted o Remove power and reappiy

2 BLINKS, Pause o Beam not aligned o Check Source, Sensor alignment

(Repeat) ON o Beam obstructed o Check for obstruction

o Sensor defective o Contact Customer Service

2 BLINKS, Pause o Wire to Sensor missing or bad o Check wiring

(Repeat) OFF o Sensor defective o Contact Customer Service

-3 BLINKS, Pause • Sensor receiving interference • Determine source of interference

(Repeat) ON o Check for interference from sun-

light or a source unit on an

adjacent door

• Contact Customer Service

4 BLINKS, Pause o Source not sending pubes o Contact Customer Service

(Repeat) • Source defective • Contact Customer Service

1 0 For Help, call 1-800-35-GENIE or visit www, geniecompanyocom

GeneraJ TroubJeshooting

Probmem What To Do

Opener does not run

from Wall Control

Door Opener starts

for no apparent reason

Door starts down, then

stops before it is

completely closed

Door starts down, then

stops andgoes back up

Door will only run dosed

Doorwill only run open

Lightswill not turn off

Door starts up, but stop'.

before it is

completely open

Operator runs,but door

doesnot move

WallConsoleVacation

Lockfunction does

not work

NoisyOperation

1. Check Lock switch on WallControl (seeWall Console section on Installation Poster).

2. Check Power Source:

* For Grounded Plug Connection.

- Plug a lamp into the electrical outlet usedfor the door opener.

a. If lamp lights, power source isgood.

b. If lamp does not light, check fuse or circuit breaker.

* For Permanent Wiring Connection.

- Checkfuse or circuit breaker.

3. Check connections (seeWail Console section on Installation Poster):

At Power Head Terminats and Walt Control.

1. Check Wiresto ensure that they are not cut (Stapes can cut insutation and short Wires)

Replaceany shorting Staples and shorted Wires.

2. Was Remote Control lost or stolen? Ifso,erase all Remote Control codes from Receiver's memory

and reprogram for remaining remote controls. (See EraseAll Receiver Memory on page 11).

3. Ensurethat no Buttons are stuck"pushed-in"on Wall Console or any Remote Controls.

1. Check dose Limit Switch setting (page 7and Installation Poster). Adjust asneeded.

2. Check Force Setting (page 7& 8).Adjust as needed.

3. Check for shorted wires.

1. Ifa new installation, check Door Arm position.

2. Checkoperation of Contact Reversefunction.

3. CheckSafe-T-Beam¢_Systemfor beam obstruction or misalignment ofLenses.

4. CheckSafe-T-Beam_ Systemdiagnostic code.

5. Checkdose Forceadjustment (seeSetLimit Switchesand ForceControls on page 7). Adjust asneeded.

6. Checkgaragedoorfor binding.

1, CheckOpen Limit Switchfor a short drcuit and for proper wiring,

2, CheckOpen Forceadjustment (seeSet Limit Switchesand ForceContro[son page 7& 8). Adjust asneeded.

:3, Checkcondition ofgarage door and door spring(s),

4, WARNJNIG:If you suspect a probtem with the garage door hardwareor springs, contact a Genie

Factory Authorized Dealer for service,or contact CustomerService at 1-800-3S-GENIE

5. Checkposition of LockSwitchon Console.

1. CheckSafe.T_Beam®SystemasdetaiIed in the Safe.T_Beam®SystemSeIf_diagn_sticTr_ubIesh__ting Chart

(page10).

2. Checkd°se Limit Switch f°r a sh°rt circuit andf°r pr°per wiring'

3. CheckCIoseForceadjustment (seeSetLimit Switchesand ForceControls on page 7&B). Adjustas needed.

1. DisconnectWires connecting WallConsoleto PowerHead(see"WalIConsoleInstallation"- on Installation poster).

Checktheir condition and either replace or reconnect.

2. Until areplacement WailConsolecan be obtained, disconnectWallConsoleand useonly RemoteControls

or WirelessKeypadto operate Opener.

3. Check for non-compatible wall control.

1. Check (ensure) that garage door and Opener are in good repair,properly lubricated, and properly

balanced asdetailed in Maintenance Section.

2, WARNING: Ifyou suspect a problem with the garage door hardware or springs, contact a Genie Factory

Authorized Dea_erfor service, or contact Customer Service at 1-800-35-GENIE,

3. CheckOpen Limit Switchfor ashort circuit and for proper wiring.

4. CheckOpen Forceadjustment (seeSetLimit Switchesand ForceControlson page 7& 8).Adjust as needed.

1. EnsureCarriageAssembly isengaged to RailDrive Screw(seeInstallCarriageAssembly-INSTALLATIONPOSTER).

2. CheckForceadjustment (seeSetLimit Switchesand ForceControls on page 7). Adjust asneeded.

3. Checkthat alIsectionsof RailDrive Screwareturning when Motor runs. Ifnot:

Checkcondition (not cracked,split,or broken)and placement of Coupler. Replaceasneeded.

Checkcondition (not cracked,split,or broken)and placement of Collarand dip. Replacethem

asneeded.

1. EnsureCarriageAssembly isin contact with CloseLimit Switch.

2. Checkwhen door isfully closed,that CarriageactivatesCloseLimit Switch. If not.adjust position of Close

Limit Switch(Seepage7).

1. Besureallfastenersaretight.

2. Check (ensure) that garage door and Opener are in good repair,properly lubricated, and properly

babnced asdescribed in Maintenance Section (page 10).

11 For Help, call 1-800-35-GENIE or visit wwwogeniecompanyocom

WIRmNG DIAGRAM

[_ WA RNiNG,'_ M;ycauseE!ectrii%_Ck--_

THERMAL

PROTECTOR

BLACK

WHITE

GREEN /_

ORANGE

PRIMARY

SEQUENCER

ORANGE

MOTOR

yELlOW

YELLOW

GREY

PRIMARY SECONDARY

.IGHTS

MOTOR

CAPACITOR

PURPLE

(Vet)

WALL

CONTROL

STB

SYSTEM

RADIOCONNECTOR

........ u

TERMINAL

STRIP

SEQUENCER/_

HOUSING

PARTS IDENTIFICATION

[1],o o,Assembly

Power Head Parts List

item Part Name

1 Power Head Assembly

A Cover (by Series Model)

B Front Plate Assembly

C Light Socket

D Motor Parts

E Receiver Assembly

F Capacitor(By Series/Model)

G Opto Wheel

H Opto-Luctor Assembly

J Sequencer Assembly

K Circuit Board Bracket

L Transformer

M Terminal Strip

N No.8-32 x 1/2" Hex Head Screw

w/Lockwasher

P No.8-32 x 3/8" Slot Hex Head

Screw w/Lockwasher

R Capacitor Isolator

4 1/4-20 Shoulder Bolt

5 1/4" Flange Nut

39 Coupler

41 No.8-32 x 3/8" Phillips

Hex Head Screw

42 No,8-32 x 3/8" Phillips

Pan Head Screw

48 Mounting Straps

49 Light Lens

For Help, call 1=800=3S-GENIE or visit wwwogeniecompany, com 1:2

PARTS [DENTmFmCATmON

[3] AssemUy

Parts List (co.t')

item Part Name

1 Power Head Assembly (see page 12)

3 RailAssembly(3-piece)

3A First Rail Section

3B Middle Rail Section

3C End Rail Section

4 1/4"-20 Hex Head Shoulder Bolt

5 1/4"-20 Hex Flange Nut

6 Carriage Stop

7 Rail Clamps

8 5/16"Hex Head Shoulder Bolt

9 5/16"Hex Flange Nut

10 Carriage Assembly

11 Collar

12 Retaining Clip

13 Rail Strap

15 Limit Swit(h Assembly

16 #8-32 x 3/8" Hex Head Screw

17 Emergency Release Cord

18 Emergency Release Knob

19 Emergency ReleaseTag (not shown)

20 Header Bracket

21 Door Bracket

22 1/4"x2"LagScrew

23 Straight Door Arm

24 Clevis Pin

25 Cotter Pin

26 Curved Door Arm

27 3/8"x 7/8"Hex Head Bolt

28 3/8" Hex Flange Nut

Number

mnduded

Parts List (cont9

_gsft

varies

Part Name

Wire (not shown)

Insulated Staples (not shown)

Wall Button (not shown)

Wall Console (not shown)

Entrapment WARNING Label (not shown)

Safe-T-Beam (STB)Sensor (green LED)

(not shown

Safe-T-Beam Source (red LED)

(not shown)

Safe-T-Beam Bracket (not shown)

Coupler

#10 x 1q/4" Phillips Hex Head Screw

Safety and Maintenance Guide

(not shown)

Wire Clip

5/16" x 3/4"Hex Head Bolt

1/4"-20 x 3/4" Self-tapping Screw

Mounting Straps

Light Lens (see page 12)

Remote Control (not shown)

44 4

46 5

47 3

48 2

49 1

50 varies

For HeJp, ca[[ 1-800-3S-GENIE or visit wwwogeniecompany, com 13

Garage Door Opener Accessories Order Form

Formu[ario de pedido de accesorios pare abndores de puertas de garaje

Formulaire de commando des accessoires pour ouvre-porte de garage

Foradditionalaccessoriesnotshown.visitourwebsiteatwww.geniecompany.com

Pareaccesodosadicionalesnomostrada,visitenuestrositiowebenwww.geniecompany.com

pourlosaccessoiressupplBmentairespasmontrB,visiternotrBsiteweb_www.geniecompany.com

(GI CT390-1 ) 1°Button compact Remote- Allowsremoteoperationof garagedoor.

Cempdmad Monde do Dgtanda- ProporciBnaroperation remotede lapumtade[ garaje.

TBIOcommandocempacto- Pemmttreop&ation _loign-de porte degarage. P/N 36248R $36.50

(G[FT390-1)1=ButtonRashlightTransmitter- RemoteControllerwith aFlashlight.

1abrocha transmgor do lintorna- Directorremotecon una[intema.

l=boutonnor FOmottourdo lampodo pocho -LecontrOMlr doign_ avecde lampede poche.

P/N 35657S $45.00

(G[ C[390-3) 3=ButtonCompact Remote- Allowsremoteoperationof3garagedoors.

Do3 botonos Comprimad Monde do Distancia- PropordOnaroperationremotedetres[aspuertasdd garaje.

3°beutonnor laTOIOcommandocompacto -Pennettreop@ation_loign'trois portes

@garage. P/N 36223R $50.00

(GWC-2W} Dduxo Wall Consdo -OperatesGarageDoor.Independentlight control.Securityvacationlock.

¢onsda do [ujodo pared -Acciona[apuertadd garaje,Controlde[uzindependiente.Cerradurade

seguridadparavacadones.

La¢onsdo dso [uxodo Mur- Acfionne laporte degarage.Commanded'_dairageind@endante.

Intermpteurde verrouilhgede s_curRO. P/N 35661 R $35.00

(GWKPD} wirdoss Keypad-Operates[ntdlicode"GarageDoorOpenerswithout RemoteControlorkey.

Sistomado ontrada per todado numOricoinal_mbrico- AccionaInsabridomsde puertasdegarajeIntellicodesin

controlremoteo Ilave.

SystOmod'ouvro-porto dogarage _ davior sansfib Actinnnelosouvre-pnrtedegarageavecIntellicode sans

td_commandeni cir.

P/N 35691R $50.00

(GLU-3} 314oz,ScrewDdvo Lubricant -Ensuresproperequipmentwearprotection.

3/4once Lubricantodo tornillo occionar -Asegmacomponentecorrectoprotection per deterioro.

Laonza3/4Lubrkant do lavis -Garantlrcomponentexactparsyst_meddenseversuser. P/N 35218A. S $5.00

(6W-2) UniversalWall Button- Providesadditionalconvenientinsideoperationofdoes _>1

BotBndo pared universal- Propordonaoperad6n convenientede[apuertodes@el interior.

neuron mural universe[- ActionneFnuvm-portedeI'int@ieurdugarage. P/N 35693R $3.75

(GPS-5} PerfectStep- Ensuresperfectparking. ZZE_....... _-

StopPorfoctd- Aseguraelestacionamientoperfecto.

Butoir PerfectStep'- Permetdestationnmala perfectiondanelegarage. P/N 35677R $4.00

(GABXS} Bolt Drive E×tonsionKit- AnExtenBonthat increasesthe travelofan Openerto accommodatean

eightfoot door.

Juogo do oxtonsi6n do cadonadoslizabla- UnaextensionparaaumentarlaIongitudde labarandade Chain

Glide,paraacomodarunapuertade 8pies(2,43m),

N&ossairo do prolongomont du couikseau - Rallongede prdongeanth coursedeI'ouvre-porteChainGlide

pouruneporte de2,4m(gpi)de hauteur. P/N 35663R $32.00

(LCBX-8} chain Ddvo ExtensionKit- An Extensionthatincreasesthe travelofanOpenerto accommodatean _

eightfoot door. _ )

Juogo do oxtonsi6n de cadonadoslizablo- UnaextensionparaaumentarlaIongituddeh barandadeChain _._/

Glide,paraacomodarunapuertade8pies(2,43m).

N&ossaira de prolongamant du coulksoau - Raliongede prdongeant[acoursede ['ouvre-pmteChainGlide

pouruneporte de2,4m(8pi)de hauteur. P/N 35679 R $32.00

(GSX-8} ScrewDrive Extension Kit- AnExtensionto increasetravelof anOperatorto accommodate

eightfoot door.

Juago do extension doslizanto do ScrewDdvo- Bnaextensionpareaumentar[acarfaredeun abridor _,

desiizaNe,paraacomodarunapuertade 8pies(2,43m.).

N&essaire de raliongodu ScrewDrive- Rallongede prolongeantla

course@I'ouvre-portepour uneportede 2,4m (8pi) dehauteur.(GIRUqT) P/N 35678R $32.00

(60WATT)Enhancad/BoughServiceLight Bulb- EnsuresproperequipmentcompatabilW /%

Bembilla do60 Vatios- Aseguracomponentecorrectode sBtema. _--_"

Edairagode 60 WATT-Garantircomponentexactparsysteme. P/N 26210A.S $2.73

(GER-2} Emergenoy Release }(it - Provides access to garage from outside in the event of

an electrical power failure.

Juego de pica-porte de pastille - Permitir entrtada desde par fuera de garaje porque corte

de el&trim.

NBcossairee de D_dencbement de seceuro - Le n&essaire de d&lenchement

de secours est consupour vous perme_tre d'accOder Rvotre garage depuis

I'extBrieur en cos de panne de courant et Iorsqu% P/N 35675R $20.00

STB Adapter Brackets (2) - Used in conjunction with standard STBBrackets.They provide

additional clearance and mounting options.

EI adaptador pone entre par_ntesis (2) - Usado en uni6n con par_ntesis uniformes de

montar de STB,ellos proporcionan el espacio libre adicional junto con mortar las opdones.

Croohets d'adaptateur (2} - UtilisB conjointement avec STBstandard mentor les crochets,

ils fournissent le dBgagement supplementaire avec mentor d'options. P/N 34439R.S $4.37

How many?

LQu_ntos_

Ordering Instructions

No C.O.D.shipments. Please include check or money order,

made payable to The Genie Company. Do not send cash.

Allow 34 weeks for delivery.

1-800-3544643. Please have part number and credit card

ready. Mail Order Form to: Genie Company, 22790 Lake

Park Blvd, Alliance, Ohio 44601 .We accept Visa or

Mastercard on phone orders only.

Pleaseadd local salestax if you leUde inone of the stateslisted

California, Connecticut, Florida, Georgia, Illinois, Indiana, Maryland,

Massachusett_ Michigan, New Jersey, New York, Ohio, Tennessee,

Virginia, Wisconsin

TOTALORDER

SHIPPING& HANDLING

STATESALESFAX

GRAND TO]:AL

S 5.o0

Las Instrucciones que Ordenan

No se aceptan pedidos de page centre entrega (COD).

SirvaseincJuir su cheque o sire postal, Jacuenta pagadera

hecha aThe Genie Company. No env[e dinero en elective.

ConcBdanos 3 a 4 semanas para[a entrega. 1-800-35&3643.

Sirvasetenor [istos los nOmeros de[ mode[o yde [atadeta de

cr_dito. Enviar hater un pedido de mercancia a:Genie

Company, 22790 LakePark Bird, Alliance, Ohio

44601Aceptamos pedidos telefBnicos de Visao Mastercard.

Silvase aglegal el impue to de venta local si usted reside en uno de los

Uguientes estados;

California, Connecticut, Florida, Georgia, Illinois, Indiana, Maryland,

Massachusetts, Michigan, New Jersey, New Yolk, Ohio, Tennessee,

VOginia,Wisconsin

TOEAL DEL PEDIDO $

FLETEYMANEJO $ 5.00

IMPUESTODEVENTASES-FATAL $

GRANTOTAL $

Instructions Commandant

Pasd'exp_ditioncentre remboursemencVeuillezindure unch#que

ou un mandatbancake,lepayablefaitaTheGenieCompany,

N'envoyezpasd'argent comptam.Accordezde 3_4 semainespour

la[ivraison.1-800-354 3643,Ayezsous[amain [enum&o de [apiece

et celuide [acarte de cr_dicMettre _[aposte learmgement a:Genie

Compan_22790LakeParkBlvd,Alliance,Ohio 4400I.Nousaccep

tons loscommandospar t_l@hone avecpaiement par cartede

credit Visaou Mastercard.

VeuiIlez indJquel los taxes de vente locales si vous i _sklez clans I'un des _,tats

repertories ci dessous

California, Connecticut, Florida, Geomia, Illinois, Indiana, Mawland,

Massachusetts, Michigan, New Jersey, New Yell<,Ohio, ]%nnessee,

Vagirda,Wiscon in

COMMANDE TOTALE $

MANUTENTION ET EXPEDITION $ 5.00

-EAXE DE VENTE $

TOTAL GLOBAL $

SHIPORDERTO:

ENVIAR MEfiCANCIA CON:

EXPEDIERMARCHANDISE POUR:

NAME/ NOMBflE/ NOM

ADDRESS/DIRECCION/ ADfiESSE

CITY/ CIUDAD/ WLLE

STArE/ EflTADO/ ETAT

ZiP / ( ODIGO POSTAL / CODE POSTAL

(Prices subject to change without notice)

(Valoran el cambio con sujeci6n a sin nora)

(Lee prix assujettissent pour changer sans [a notification)

For Help, call 1-800-35-GENIE or visit www.geniecompany.com

Genie 36280S Owner's manual

Brand: Genie

Model: 36280S

Category: Garage Door Opener

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Genie 36280S Owner's manual

This manual is also suitable for

Genie 36280S Owner's manual

Related papers

Other documents