Mettler Toledo (Software Version 2.2) Transmitter Module PA 700(X) Operating instructions

Measuring Module

M 700

®

PA 700(X)

Communication Unit

for PROFIBUS PA

Trademarks

The following registered trademarks are used in this instruction manual

without further marking

SMARTMEDIA

®

is a registered trademark of Toshiba Corp., Japan

FOUNDATION FIELDBUS™

is a trademark of Fieldbus Foundation, Austin, USA

Warranty

Defects occurring within 1 year from delivery date shall be remedied free of charge at our plant

(carriage and insurance paid by sender). Sensors, fittings, and accessories: 1 year.

Return of products under warranty

Please contact our Service Team before returning a defective device. Ship the cleaned device to

the address you have been given. If the device has been in contact with process fluids, it must be

decontaminated/disinfected before shipment. In that case, please attach a corresponding certificate,

for the health and safety of our service personnel.

Disposal

Please observe the applicable local or national regulations concerning the disposal of

“waste electrical and electronic equipment”.

Mettler-Toledo AG,

Process Analytics, Industrie Nord, CH-8902 Urdorf,

Tel. +41 (44) 729 62 11 Fax +41 (44) 729 26 36

Subject to technical changes.

3

4

Contents

M 700 PA 700 Module

Warranty .....................................................................................................2

Disposal ....................................................................................................... 2

Trademarks ..................................................................................................2

Contents .................................................................................................... 4

Intended Use ...............................................................................................6

Conformity with FDA 21 CFR Part 11 ..........................................................6

Safety Information .......................................................................................7

Application in Hazardous Locations: PA 700X Module .................................7

Software Version ........................................................................................8

Modular Concept ........................................................................................ 9

Short Description ......................................................................... 10

Short Description: FRONT Module ..............................................................10

Short Description: Menu Structure .............................................................11

Short Description: BASE Module ................................................................13

PROFIBUS Technology .................................................................. 14

Terminal Plate PA 700(X) Module ............................................... 16

Attaching the Terminal Plates .............................................................. 16

Inserting the Module ................................................................... 17

PROFIBUS PA Installation ............................................................ 18

Communication Model ..............................................................................20

Physical Block (PB) ......................................................................................20

Analog Input blocks ...................................................................................21

For Copy: Individual Settings ......................................................................24

Configuration with PROFIBUS ....................................................................25

Device database file (GSD file) ...................................................................25

Cyclic Data Communication .......................................................................26

Structure of Cyclic Input Data Telegram ................................... 26

DI Function Blocks .....................................................................................27

DI 1: EC 400 status ............................................................................. 27

DI 2: CONTACTS / LOCK Status / ENABLE Request .............................. 27

DI 3: EC 400 Messages ....................................................................... 28

Explanation of EC 400 Messages: Maintenance request ...................... 28

5

Contents

M 700 PA 700 Module

Explanation of EC 400 Messages: Failure ............................................. 29

DI 4: EC 400 Step ............................................................................... 29

DO Function Blocks ....................................................................................30

DO 1: HOLD Control ........................................................................... 30

DO 2: PARSET...................................................................................... 30

DO 3: EC 400 Control ......................................................................... 31

DO 4: LOCK Control ........................................................................... 31

Configuration Data ....................................................................................32

Analog Input blocks (1 ... 8) ...................................................................... 33

Discrete Input Blocks (1 ...4) ......................................................................34

Discrete Output Blocks (1 ... 4) .................................................................. 35

PA Slot Model ............................................................................................ 36

PB Block Parameters ..................................................................................37

TB Analyzer Block Parameters ....................................................................39

AI Function Block Parameters .....................................................................41

Defaults & Writable Ranges ....................................................................... 41

DI Function Block Parameters .....................................................................44

DI Function Block Parameters .....................................................................45

DO Function Block Parameters ...................................................................46

AO Function Block Parameters ...................................................................48

Calibration Record Parameters ................................................................... 49

Menu Selection ............................................................................ 61

Passcode Entry ............................................................................. 62

Changing a passcode .......................................................................... 62

Passcode lost ....................................................................................... 62

Function Control Matrix ............................................................................63

Pressure Compensation via Bus (AO1) ....................................... 64

Diagnostics: Bus Monitor ...........................................................................65

Bus Monitor ..............................................................................................66

Specifications ............................................................................... 67

Index ............................................................................................. 73

6

Intended Use

In their directive “Title 21 Code of Federal Regulations, 21 CFR Part 11,

Electronic Records; Electronic Signatures“ the US American health agency

FDA (Food and Drug Administration) regulates the production and processing

of electronic documents for pharmaceutical development and production.

This results in requirements for measuring devices used for correspond-

ing applications. The following features ensure that the M 700(X) modular

process analysis system meets the demands of FDA 21 CFR Part 11:

Electronic Signature

Access to the device functions is regulated and limited by individually adjust-

able codes – “Passcodes“. This prevents unauthorized modification of device

settings or manipulation of the measurement results. Appropriate use of

these passcodes makes them suitable as electronic signature.

Audit Trail Log

Every change of device settings can be automatically recorded and docu-

mented in the Audit Trail Log on the SmartMedia card. The recording can be

encrypted.

Conformity with FDA 21 CFR Part 11

The module is a communication unit for PROFIBUS-PA and allows digital

communication via current modulation.

The PA 700X module is intended for operation in locations subject to explo-

sion hazards which require equipment of Group II, device category 2(1), gas/

dust.

7

Safety Information

Application in Hazardous Locations

Caution!

Never try to open the module! If a repair should be required, return the

module to our factory.

If the specifications in the instruction manual are not sufficient for assessing

the safety of operation, please contact the manufacturer to make sure that

your intended application is possible and safe.

Application in Hazardous Locations:

PA 700X Module

When using the PA 700 X module, the stipulations for electrical installations

in hazardous areas (EN 60079-14) must be observed. When installing the

device outside the range of applicability of the 94/9/EC directive, the appro-

priate standards and regulations in the country of use must be observed.

The module has been developed and manufactured in compliance with the

applicable European guidelines and standards.

Compliance with the European Harmonized Standards for use in hazardous

locations is confirmed by the EC-Type-Examination Certificate.

Compliance with the European guidelines and standards is confirmed by the

EC Declaration of Conformity.

There is no particular direct hazard caused by the operation of the device in

the specified environment.

Be sure to observe during installation:

Switch off power supply before replacing or inserting a module.

Before commissioning it must be proved that the device may be connected

with other equipment.

•

8

Software Version

PA 700(X) Module

Device Software M 700(X)

The PA 700(X) module is supported by software version 5.0 or higher.

Module software version 2.x requires device software version 7.x.

Module Software COMPA 3400(X)-081

Software version 1.3 01.06.2004

Software version 2.2 02.04.2007

Menu Display Device description

Provides information about all

modules installed: Module type and

function, serial number, hardware

and software version and device

options.

Select the different modules (FRONT,

BASE, slots 1 - 3) using the arrow

keys.

Device description

Return

22.7 °C

0.003mS/cm

Operating panel

Module FRONT 700-011

Hardware: 1, Software: 7.0

Serial number 0000815

BASE

Module

FRONT

Query actual device/module software

When the analyzer is in measuring mode:

Press menu key, open Diagnostics menu.

Options

9

Modular Concept

Basic Unit, Measuring Module, Additional Functions

Documentation

The basic unit is accompanied by a CD-ROM containing the complete

documentation.

Latest product information as well as instruction manuals for earlier software

releases are available at www.mtpro.com.

The M 700(X) is an expandable modular process analysis system.

The basic unit (FRONT and BASE modules) provides three slots which can be

equipped by the user with any combination of measuring or communication

modules. The software capabilities can be expanded by additional functions

(options). Additional functions must be ordered separately. They are supplied

with a device-specific TAN for function release.

3 module slots

for free combination of

measuring and

communication modules

Measuring modules

pH / ORP / Temp

0

2

/Temp

Noncontacting conductivity/Temp

Contacting conductivity/Temp

•

Additional

functions

Activation via device-

specific TAN

SmartMedia card

Data recording

M 700(X) Modular Process Analysis System

Communication modules

OUT (additional switching and

current outputs)

PID (analog and digital controller)

Profibus PA

Foundation Fieldbus

EC 400 probe controller

•

10

Short Description

Short Description: FRONT Module

Transflective LC graphic display

(240 x 160 pixels)

white backlighting, high resolution

and high contrast.

Red LED

signals failure (On) or

maintenance request/function check

(flashing) according to NE 44.

4 captive screws

for opening the analyzer

(Caution! Make sure that the gasket between

FRONT and BASE is properly seated and clean!)

Green LED

Voltage supply okay

5 self-sealing cable glands

M20 x 1.5

for entry of voltage supply and signal lines

2 softkeys

with context-sensitive functions.

User interface

with plaintext menus as

recommended by NAMUR.

Menu texts can be switched to:

German, English, French, Italian,

Swedish, and Spanish.

Intuitively acquirable menu logic,

based on Windows standards.

Control panel

3 function keys

(menu, meas, enter)

and 4 arrow keys for menu selection

and data entries

Measurement display

Secondary displays

%Air

°C

24.0°C

25.8°C

11

Measuring

Short Description: Menu Structure

Basic Functions: Calibration, Maintenance, Parameter Setting, Diagnostics

Calibration

Maintenance

Parameter setting

Diagnostics

Menu groups

1

2

3

1147

2958

1246

Operator level

1989

Administrator level

Passcode:

Selection of

further menu

items:

Module 1

Module 2

Module 3

BASE

Module 1

Module 2

Module 3

SYSTEM

FRONT

BASE

Module 1

Module 2

Module 3

Message list

Point of meas

description

Logbook

Device description

FRONT

BASE

Module 1

Module 2

Module 3

4

5

6

Legend:

Pressing the menu key accesses menu selection.

Pressing the meas key returns to measurement.

Menu groups are selected using the arrow keys.

Press enter to confirm, enter passcode.

Further menu items are displayed.

Selected functions of the Diagnostics menu can be

recalled via softkey even when in measuring mode.

1)

2)

3)

4)

5)

6)

12

Short Description: FRONT Module

View into the open device (FRONT module)

Terminal plates

of “hidden” modules

Each module comes with an adhesive

label containing the contact assignments.

This label should be sticked to the inner

side of the front (as shown). Then, the

terminal assignments remain visible even

if further modules are inserted.

Slot for SmartMedia card

Data recording

The SmartMedia card expands the

measurement recorder capacity to

> 50000 records.

Exchange of parameter sets

5 parameter sets can be stored on

the SmartMedia card. The 2 internal

parameter sets can be switched by

remote control.

Configurations can be transmitted

from one analyzer to the other.

Function expansions

are possible with additional software

modules, which are released using

transaction numbers (TAN)

Software updates

•

The circumferential sealing

guarantees IP 65 protection and allows

spray cleaning / disinfection.

Caution! Keep clean!

Replacing the front module

Pull off power cord and ground wire.

To separate the FRONT module

from the BASE module, turn the

retaining screws of the pivot hinge by

90°.

13

Short Description: BASE Module

View into the open device (BASE module, 3 function modules installed)

BASE module

2 current outputs (free assignment of

process variable) and 4 relay contacts,

2 digital inputs.

VariPower broad-range power supply,

20 ... 265 V AC/DC, suitable for all public

mains supplies in the world.

Power supply units, IS version:

100 ... 230 V AC or

24 V AC/DC

Important notice concerning SmartMedia card

The SmartMedia card may be inserted or replaced with the power supply

switched on. Before a memory card is removed, it must be “closed” in the

maintenance menu. When closing the device, make sure that the sealing is

properly seated and clean.

Module equipment

Module identification: Plug & Play.

Up to 3 modules can be combined as

desired. Several input and communication

modules are available.

Warning!

Do not touch the terminal compartment, there may be

dangerous contact voltages!

14

PROFIBUS Technology

PROFIBUS is a digital communication system that connects different field

devices over a common cable and integrates them into a control system. In

the long term, PROFIBUS will replace the 4-20mA technology, which only

supplies pure measured values. Advantages of the PROFIBUS technology are:

easy and cost-saving cabling

convenient operation over a central control station

transmission, evaluation, and control of high amounts of data from field

device to control station.

devices installed in hazardous locations are configured and maintained

from the control station

PROFIBUS is the leading open fieldbus system in Europe. Its application range

covers manufacturing, process, and building automation. As open fieldbus

standard to EN 50170 and IEC 61158, PROFIBUS ensures communication of

different devices over one bus. The PROFIBUS User Organization (PNO) pro-

vides for further development and maintenance of the PROFIBUS technology.

It combines the interests of users and manufacturers.

Variants and Basic Characteristics

PROFIBUS determines the technical and functional characteristics of a serial

bus system. There are three PROFIBUS variants:

PROFIBUS-DP (decentralized peripherals)

Tailored for communication of automation systems and distributed periph-

erals.

RS 485 standard with transmission rates up to 12 MBits/sec

PROFIBUS-PA (process automation)

Dedicated to the process industry. It permits connection of sensors and

actuators to a common bus even in hazardous locations. PROFIBUS-PA has

a transmission rate of 31.25 kBits/sec.

•

15

PROFIBUS Technology

PROFIBUS distinguishes between two types of devices:

Masters

Control the data traffic on the bus. They send messages without external

request.

Slaves

Peripheral devices such as valves, drives, transmitters, and analyzers. They

can react acyclically to servicing, configuration and diagnostic tasks of the

master. The central controller cyclically reads the measurement data with

status.

Definitions for PROFIBUS-PA

The bus protocol defines type and speed of the data exchange between

master and slave devices and determines the transmission protocol of the

respective PROFIBUS system.

PROFIBUS-PA permits cyclic and acyclic services.

Cyclic services are used for transmission of measurement data and actuating

commands with status information.

Acyclic services are used for device configuration, maintenance and diag-

nostics during operation.

The PA 3.0 device profile defines the device class and typical functionalities

with parameters, ranges, and limit values.

The FISCO model developed by the German PTB for hazardous locations per-

mits connection of several devices to one common bus and defines permis-

sible limits for device and cable parameters.

•

16

Terminal Plate

PA 700(X) Module

Attaching the Terminal Plates

The terminal plates of the lower modules

can be sticked to the inner side of the door.

This facilitates maintenance and service.

Terminal Plate PA 700 Module:

Terminal Plate PA 700X Module:

17

Inserting the Module

Switch off power supply

Open the device (loosen the 4 screws at the front)

Place module in slot (D-SUB connector)

Tighten fastening screws of the module

Connect signal lines

Close device, tighten screws at the front

Switch on power supply

Assigning process variables to AI blocks on the device

Set parameters

Make sure that the cable

glands are tightly closed to

protect against humidity.

Thanks to the staggered arrangement of

connectors and fastening screws the termi-

nal strips of all modules are easy to access.

1.

2.

3.

4.

5.

6.

7.

8.

9.

18

PROFIBUS PA Installation

Basic build-up of a PROFIBUS system:

e.g. M 700(X)

with module

PA 700(X)

Shield

12

13

PA 700(X) Module

PROFIBUS cable

PA- (green)

PA+ (red)

14

Electrical connection between module and PROFIBUS PA is in accordance

with the PROFIBUS Guideline, Order No. 2.092 (www.profibus.com).

PROFIBUS-DP

PROFIBUS-PA

Slave 1

Control room

Slave 2 Slave n

...... ..... .....

AI 1

Analog Input

Function Block

Physical Block

Global Status

AI 2

Analog Input

Function Block

AI 3

Analog Input

Function Block

AI 4

Analog Input

Function Block

Module Selection

Process Variable Selection

Protocols

Calibration

AO

Analog Output

DI 1

DI 2

DI 3

DI 4

DO 1

DO 2

DO 3

DO 4

Meas. Value Correction

EC 400 Status

CONTACT Status

EC 400 Message

EC 400 Step

HOLD Control

PARSET

EC 400 Control

LOCK Control

PROFIBUS PA

Module I

Module II

Calc. Block I

Calc. Block II

ATB 1

Analyzer Transducer

Block

ATB 2

Analyzer Transducer

Block

ATB 3

Analyzer Transducer

Block

ATB 4

Analyzer Transducer

Block

AI 5

Analog Input

Function Block

AI 6

Analog Input

Function Block

AI 7

Analog Input

Function Block

AI 8

Analog Input

Function Block

Module Selection

Process Variable Selection

Protocols

Calibration

Module I

Module II

Calc. Block I

Calc. Block II

ATB 5

Analyzer Transducer

Block

ATB 6

Analyzer Transducer

Block

ATB 7

Analyzer Transducer

Block

ATB 8

Analyzer Transducer

Block

20

Communication Model

See diagram on previous side

The device parameters are sorted in three types of blocks:

Physical Block (PB)

This block contains the general parameters which apply to the whole device.

Transducer Blocks (TB 1 ... TB 8)

8 analog blocks. They contain measurement parameters (process variable,

temperature) according to the PROFIBUS-PA Profile 3.0 specification.

Function Blocks

8 analog input blocks (AI1..4, AI5..8, for scaling measured values),

4 digital output blocks (DO 1 ... DO 4, for control signals)

4 digital input blocks (DI 1 ... DI 4, for status messages).

1 analog output block (AO 1) for analog compensation signals,

e.g. O

2

process pressure.

Physical Block (PB)

This block contains the device-specific parameters (model designation, manu-

facturer ID, serial number...) and controls basic device functions such as:

Write protection

(“WRITE_LOCKING” parameter) Enables or locks acyclic services

(maintenance, configuration).

Blocking operator access to the device

(“LOCAL_OP_ENA” parameter)

Enables or locks access via the user interface on the device.

Notice:

When communication fails for more than 30 seconds,

the device automatically switches to local access.

Reset

(“FACTORY_RESET” parameter)

Caution – data loss!

Resets all configuration values to factory setting.

•

Page is loading ...

Mettler Toledo (Software Version 2.2) Transmitter Module PA 700(X) Operating instructions

Mettler Toledo (Software Version 2.2) Transmitter Module PA 700(X) Operating instructions

Related papers

Other documents