Fibaro FGT-001 Short Manual

THE HEAT

CONTROLLER

RADIATOR THERMOSTAT

FGT-001

Quick Manuals. Warranty Terms

Page is loading ...

3

1. Connect the charger to the micro-USB port to

charge the device.

If you have the temperature sensor:

a. Use a coin to open the battery cover by

turning it counter-clockwise.

b. Remove the sticker underneath the battery.

c. Use a coin to close the battery cover by

turning it clockwise.

2. Disconnect the charger when the LED ring

pulses green (device fully charged).

3. Dismount your current thermostatic head.

4. Depending on type of your valve:

5. Mount the device on the valve and tighten it by

turning the cap clockwise.

6. Press and hold the button for at least 1 second.

7. The LED ring will start blinking blue.

If you have the temperature sensor:

a. Click the button on the

temperature sensor.

b. The LED ring will blink

green 5 times if the connec-

tion was successful.

8. Set the main Z-Wave controller in add mode.

9. Triple click the button on the thermostatic head.

The LED ring will start blinking white.

10. If you are adding in S2 authenticated mode,

type in the device pin code (underlined part of

the public key on the label).

11. Successful adding will be conrmed by the

controller.

ENGLISH

Use

adapter:

Danfoss RA-N

Use

adapter:

Danfoss RTD-N

Proceed

normally

M30 x 1.5

For full instruction manual and

technical specication please visit

our website:

manuals.baro.com/en/heat-controller

First launch

FIBARO Heat Controller is a remotely controlled

thermostatic head to control temperature in your

room. It measures the temperature and automati-

cally adjusts the heat level.

It can be mounted without tools on three types of

thermostatic radiator valves.

You can create schedules via app to easily manage

temperature throughout the week.

Read the manual before

attempting to install the device!

4

Thermostatic Head:

Power supply: 3.7V Li-Poly battery pack

(non-replaceable)

Supported charger: micro-USB 5V, min. 0.5A

Radio protocol: Z-Wave (S2-enabled)

Radio frequency bands: 868.0-868.6 MHz

869.7-870.0 MHz

2402-2480 MHz

Max. transmit power: 6dBm (Z-Wave)

7dBm (BLE)

Operating temperature: 0-40°C

Maximum water

temperature:

90°C

Supported valves: M30 x 1.5, Danfoss RTD-N,

Danfoss RA-N

Dimensions (D x L): 56 x 74 mm

56 x 87 mm (with adapter)

Temperature Sensor (optional):

Power supply: 3.0V CR2032 battery

(included)

Radio frequency band: 2402-2480 MHz

Max. transmit power: 1dBm

Operating temperature: 0-40°C

Dimensions (D x H): 38 x 12 mm

Warranty terms and conditions

Specications

1. FIBAR GROUP S.A. with its registered oce in

Wysogotowo, ul. Serdeczna 3, 62-081 Wysogotowo,

ul. Lotnicza 1, 60-421 Poznań, entered into the Reg-

ister of Entrepreneurs of the National Court Register

maintained by the District Court for Poznań-Nowe

Miasto and Wilda in Poznań, VIII Commercial Divi-

sion of the National Court Register (KRS) under num-

ber: 553265, NIP 7811858097, REGON: 301595664,

share capital PLN 1,182,100 paid in full, other con-

tact information is available at: www.baro.com

(hereinafter "the Manufacturer") guarantees that

the device sold (hereinaftr: "the Device" is free from

material and manufacturing defects.

2. The Manufacturer shall be responsible for mal-

functioning of the Device resulting from physical

defects inherent in the Device that cause its oper-

ation to be incompatible with the specications

within the period of:

- 24 months from the date of purchase by the con-

sumer,

- 12 months from the date of purchase by a business

customer (the consumer and business customer are

further collectively referred to as "Customer").

3. The Manufacturer shall remove any defects re-

vealed during the guarantee period, free of charge,

by repairing or replacing (at the sole discretion of

the Manufacturer) the defective components of the

Device with new or regenerated components. The

manufacturer reserves the right to replace the entire

Device with a new or regenerated device. The Manu-

facturer shall not refund money paid for the device.

4. Under special circumstances, the Manufacturer

may replace the Device with a dierent device most

similar in technical characteristics.

5. Only the holder of a valid guaranty document

shall be entitled to make claims under guarantee.

6. Before making a complaint, the Manufacturer

recommends using the telephone or online support

Simplied EU declaration of conformity:

Hereby, Fibar Group S.A. declares

that the device is in compliance with

Directive 2014/53/EU and 2011/65/

EU, 2015/863. The full text of the EU

declaration of conformity is available

at the following internet address:

www.manuals.baro.com

WEEE Directive Compliance:

Device labelled with this symbol should not

be disposed with other household wastes.

It shall be handed over to the applicable

collection point for the recycling of waste

electrical and electronic equipment.

Legal information

Risk of explosion if battery is replaced by an incor-

rect type. Dispose of used batteries according to the

instructions.

This product is not a toy. Keep away from children and

animals! CR2032 coin cells are harmful if swallowed!

Warnings

5

available at https://www.baro.com/support/.

7. In order to make a complaint, the Customer

should contact the Manufacturer via the email ad-

dress given at https://www.baro.com/support/.

8. After the complaint has been properly led, the

Customer will receive contact details for the Au-

thorized Guarantee Service ("AGS"). The customer

should contact and deliver the Device to AGS. Upon

receipt of the Device, the manufacturer shall inform

the Customer of the return merchandise authoriza-

tion number (RMA).

9. Defects shall be removed within 30 days from the

date of delivering the Device to AGS. The guarantee

period shall be extended by the time in which the

Device was kept by AGS.

10. The faulty device shall be provided by the Cus-

tomer with complete standard equipment and doc-

uments proving its purchase.

11. The cost of transporting the Device in the terri-

tory of the Republic of Poland shall be covered by

the Manufacturer. The costs of the Device transport

from other countries shall be covered by the Cus-

tomer. For unjustied complaints, AGS may charge

the Customer with costs related to the case.

12. AGS shall not accept a complaint claim when:

- the Device was misused or the manual was not

observed,

- the Device was provided by the Customer incom-

plete, without accessories or nameplate,

- it was determined that the fault was caused by oth-

er reasons than a material or manufacturing defect

of the Device

- the guarantee document is not valid or there is no

proof of purchase,

13. The guarantee shall not cover:

- mechanical damages (cracks, fractures, cuts, abra-

sions, physical deformations caused by impact,

falling or dropping the device or other object, im-

proper use or not observing the operating manual);

- damages resulting from external causes, e.g.: ood,

storm, re, lightning, natural disasters, earthquakes,

war, civil disturbance, force majeure, unforeseen ac-

cidents, theft, water damage, liquid leakage, battery

spill, weather conditions, sunlight, sand, moisture,

high or low temperature, air pollution;

- damages caused by malfunctioning software,

attack of a computer virus, or by failure to update

the software as recommended by the Manufacturer;

- damages resulting from: surges in the power and/

or telecommunication network, improper connec-

tion to the grid in a manner inconsistent with the

operating manual, or from connecting other devices

not recommended by the Manufacturer.

- damages caused by operating or storing the device

in extremely adverse conditions, i.e. high humidity,

dust, too low (freezing) or too high ambient temper-

ature. Detailed permissible conditions for operating

the Device are dened in the operating manual;

- damages caused by using accessories not recom-

mended by the Manufacturer

- damages caused by faulty electrical installation of

the Customer, including the use of incorrect fuses;

- damages caused by Customer's failure to provide

maintenance and servicing activities dened in the

operating manual;

- damages resulting from the use of spurious spare

parts or accessories improper for given model, re-

pairing and introducing alterations by unauthorized

persons;

- defects caused by operating faulty Device or ac-

cessories.

14. The guarantee shall not cover natural wear and

tear of the Device and its components listed in the

operating manual and in technical documentation

as such elements have a dened operational life.

15. The Device Guarantee shall not exclude, limit or

suspend the Customer's warranty rights.

16. The Manufacturer shall not be liable for dam-

ages to property caused by defective device. The

Guarantor shall not be liable for indirect, incidental,

special, consequential or punitive damages, or for

any damages, including, inter alia, loss of prots,

savings, data, loss of benets, claims by third parties

and any other damages arising from or related to

the use of the Device.

Page is loading ...

105473510101

Made in Poland

www.baro.com

Fibaro FGT-001 Short Manual

Related papers

Other documents