Powermate PWSTM4317 User manual

Look inside for:

Page

Safety Definitions ........................1

Important Safety Information .............. 2-3

Product Specifications ....................4

Parts & Features ........................4

Assembly ............................. 5-6

Operation .............................7-10

Routine Maintenance ................... 11-12

Storage................................12

Troubleshooting ........................13

Technical Service .......................13

Warranty ...............................14

09/28/18 Printed in China A204064

Operator’s Manual

WHEELED STRING

TRIMMER MOWER

Gasoline Powered 43cc, 2 Cycle

Record the following for future reference:

Mfg. Date Code : _____________________

Date of Purchase: Attach a copy of your sales receipt.

Consumer Toll Free Number: 1-800-737-2112

Refer to the website for electronic manual and parts book.

www.powermateoutdoor.com

IMPORTANT:

Thank you for purchasing this Powermate

®

Trimmer.

This manual provides complete instructions for safely operating, and maintaining your Trimmer. Read and

save these instructions. Refer to this manual each time before using your Trimmer.

WARNING: CONTAINS LEAD. May be harmful if eaten or chewed. May generate dust containing lead. Wash

hands after use. Keep out of reach of children.

WARNING: This product can expose you to chemicals including lead, which is known to the State of

California to cause cancer and birth defects or other reproductive harm. For more information go to www.

P65Warnings.ca.gov.

KEEP THIS MANUAL FOR FUTURE REFERENCE

If you have a question or problem...CALL TOLL FREE:

1-800-737-2112

Model No. PWSTM4317.2

Safety Definitions

• Save all instructions

DANGER

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE

Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

The information listed below should be read and understood by the operator. We utilize the symbols below to allow the

reader to recognize important information about their safety.

Safety Alert Symbols:

Safety Warning Symbols:

Control and Operating Symbols:

CHOKE/

COLD

START

RUN/

WARM

START

6x

PRIMER BULB

ON

UNDER SIDE

Choke Control:

Cold Start

Run/Warm Start

Fuel Mixture

50:1

Unleaded Gas: 2 Cycle Oil

Caution: Do Not Use Gas

Mix with More Than 10%

Methanol or Ethanol

Fuel Mixture:

50:1

(Unleaded Gas : 2 Cycle Oil)

CHOKE/

COLD

START

RUN/

WARM

START

6x

PRIMER BULB

ON

UNDER SIDE

Fuel Primer:

Press 6 times

STOP

ON/

RUN

Ignition Switch:

ON

OFF

Look for this symbol to point out important safety precautions. It means: Attention! Become Alert!

Your Safety Is Involved.

Read, understand and follow operator’s manual before operating this machine. Failure to follow

directions could result in serious injury.

Always wear eye protection that meets or exceeds the requirements of ANSI Z87.1.

Wear hearing protection.

Wear safety footwear.

Engine exhaust contains carbon monoxide, an odorless and deadly gas. NEVER run unit indoors

or in a poorly ventilated area.

Keep all by-standers at least 50 ft. (15 m) away. Stop machine if anyone enters the area.

This equipment can throw small objects at high speed causing personal injury. Inspect area

where used and remove all foreign objects.

Keep all parts of your body away from the rotating trimmer lines.

To reduce risk of fire, clean spilled gas and keep unit free from debris. Gasoline is extremely

flammable. Allow machine to cool before refueling.

Hot surface. Do not touch a hot muffler, gear box or cylinder, you may get burned. These parts get

extremely hot from operation and remain hot for a short time after the unit is turned off.

Before Operating Trimmer:

READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE OPERATING TRIMMER.

Read and follow all warnings and safety instructions. Failure to do so can result in serious injury to you or bystanders.

WARNING

1. Avoid dangerous environments.

a. Do not operate Trimmer while under the influence of alcohol, medications, or drugs.

b. Do not operate Trimmer when you are tired.

c. Do not use this Trimmer if you are mentally or physically unable to operate safely.

2. Inspect Trimmer for damaged parts, and make sure all fasteners and guards are in place and secure. Replace any

damaged parts.

3. Use only 0.095 or 0.105 inch diameter flexible, nonmetallic line with this Trimmer.

This Trimmer is designed for use with a non-metallic flexible string. Never use this Trimmer with other accessories not

specifically approved for use in this manual. Never use alternative cutting members such as wire or wire-rope, which can

break off and become a dangerous projectile.

4. Dress properly when operating Trimmer.

a. Always wear heavy long pants, boots, gloves, and a long-sleeve shirt.

b. Do not wear loose clothing or jewelry that can get caught in the moving parts of the Trimmer.

c. Always wear gloves and substantial foot wear when working outside.

d. Always wear protective hair covering to contain long hair.

5. Always wear a face or dust mask if operating in dusty conditions.

6. Always wear eye protection that meets or exceeds the requirements of ANSI Z87.1.

7. Always wear hearing protection which meets or exceeds ANSI standards.

8. Thoroughly inspect the area where the Trimmer is to be used and remove all foreign objects.

Your equipment can throw small objects at high speed causing personal injury or property damage.

WARNING

DANGER

Important Safety Information

• Save all instructions

DANGER

While Operating Trimmer:

1. Stay alert. Focus on safe operation and be aware of your operating environment.

2. Do not operate Trimmer if it is damaged or not securely and fully assembled.

3. Only well instructed adults should operate Trimmer. Never allow children to operate Trimmer.

4. Keep children away. Keep all bystanders at least 50 ft (15 m) away.

5. This Trimmer is only intended for trimming, scalping, and mowing. Do not use Trimmer for any job except that for

which it is intended. Do not use for edging, pruning or hedge trimming.

6. The Trimmer line may be spinning during carburetor adjustments. Make carburetor adjustments with lower end

supported to prevent trimmer line from contacting any object.

7. Maintain your balance and proper footing at all times. Do not overreach.

8. Keep all parts of your body away from cutting area, the rotating trimmer lines and hot surfaces.

9. Hold the unit firmly with both hands.

10. Do not force Trimmer. It will do the job better and with less likelihood of a risk of injury by using it at the rate for

which it was designed.

11. Never start or run the unit inside a closed room or building; breathing exhaust fumes can kill.

12. After turning the Trimmer off, make sure the trimmer line has stopped before approaching the trimmer head.

Important Safety Information (Continued)

• Save all instructions

While Operating Trimmer:

Prolonged exposure to vibrations through use of gasoline powered hand tools could cause blood vessel or nerve

damage in fingers, hands, and joints of people prone to circulation disorders or abnormal swellings. Extensive use

in cold weather has been linked to blood vessel damage in otherwise healthy people. If symptoms occur such as

numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek medical attention.

CAUTION

Fuel Safety:

1. Mix and pour fuel outdoors WHERE THERE ARE NO SPARKS OR FLAMES.

2. Use a container approved for gasoline.

3. Do not smoke or allow smoking near fuel or the Trimmer.

4. Avoid spilling fuel or oil. Wipe up all fuel spills.

5. Move at least 10 ft (3 m) away from fueling site before starting engine.

6. Stop engine and allow to cool before removing fuel cap. Remove fuel cap slowly.

Maintenance & Storage of Trimmer:

1. Disconnect the spark plug before performing maintenance.

2. Maintain Trimmer with care. Inspect Trimmer periodically. If Trimmer is not working properly or damaged, have it

repaired by a qualified service center.

3. Check for misalignment of moving parts, binding of moving parts, broken parts, mounting, and any other condition

that may affect its operation.

4. Keep guards in place and in working order.

5. A guard or other part that is damaged should be properly repaired or replaced by a qualified service center.

6. Use only genuine Powermate

®

replacement parts and accessories. Use of any non-Powermate

®

parts or

accessories could lead to injury, damage to the unit, and will void your warranty.

7. Do not remove or modify any parts. Removing or modifying parts could lead to injury, damage the Trimmer and will

void the warranty.

8. Keep handles dry, clean, and free from oil and grease.

9. Allow engine to cool and empty the fuel tank before storing or transporting in vehicle. Use up remaining fuel in the

carburetor by starting the engine and letting it run until it stops.

10. When not in use, store Trimmer indoors in a dry location. Store Trimmer in a locked area out of the reach of children.

11. Store unit and fuel in area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors

or switches, furnaces, etc.

WARNING

Engine .............................. 43 cc, 2 cycle

Speed ........7,000-8,500 RPM depending on string size

Cutting Diameter .................17 inches (432 mm)

Line Diameter.....................0.095 or 0.105 inch

Spool Type . . . . . . . . . . . . . . . . . Manual loaded, Twin-Line

Fuel Tank Capacity.................... 28 oz (840 ml)

Fuel Type .......

Unleaded Gasoline – 87 Octane or higher

2-Cycle Oil Type........

2-Cycle Oil that meets or exceeds

JASO – FC Specifications

Fuel Mixture ................

50:1 (Gasoline: 2-Cycle Oil)

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . NGK - BPMR6A

CHAMPION - CJ8 or equivalent

Net Weight ...........................39 lbs (18 kg)

Product Specifications

• Save all instructions

Parts & Features

1.

Trimmer Head Assembly

7.

On/Off Ignition Switch

13.

Fuel Tank

2.

Engine Air Intake Screen

8.

Recoil Starter Handle

14.

Air Filter Cover

3.

Trimmer Guard

9.

Choke

15.

String Storage

4.

Trimmer Line Knife

10.

Fuel Primer Bulb 16. Bevel Handle

5.

Front Handle

11.

Spark Plug 17. Swivel Control

6.

Throttle Lever

12.

Muffler

8

9

1

4

5

11

3

6

7

10

12

13

14

15

2

16

17

Assembly

• Save all instructions

Parts Included With The Packaged Trimmer:

If you need assistance or find any parts missing,

CALL TOLL FREE: 1-800–737-2112

Handle Assembly:

A

Cutting Head Assembly:

B

Tools Needed For Assembly:

Unpacking:

• 10 mm wrench or adjustable wrench

• 14 mm socket or open wrench

1. Remove components from carton.

2. Cut white cable ties. Do not cut black cable ties.

3. Remove foam and corrugated protection.

Do not operate Trimmer if it is damaged or not securely and fully assembled.

WARNING

1. Install middle handle to lower handle at one of the two

height adjustment locations and secure using two

saddle bolts and plastic knobs. Orient handle so small

metal clips are to the right side. Route pivot cable

through middle handle. Assemble with knobs to the

inside of the lower handle. Tighten knobs securely.

(Fig. 1)

2. Install upper handle to middle handle and secure using

two saddle bolts and plastic knobs. Orient handle so

the “V” shape is upward. Assemble with knobs to the

inside of the middle handle. Route the throttle cable

below the right side of the middle handle. Tighten

knobs securely. Secure throttle cable to the handles

with provided metal clips as shown. Secure the pivot

cable with provided plastic cable tie.

(Fig. 2)

3. Use handle height adjustment holes on middle handle

to adjust to your preferred handle height.

1. Install the cutting head assembly into the

clutch housing with the metal saddle engaging the

clutch housing. (Fig. 3) It may be necessary to rotate

the trimmer head slightly to align the shaft splines.

2. Screw the camlock inward and rotate the handle

to clamp the tube to the housing. Try to rotate the

tube within the housing. If you can rotate the tube

at all, unlock the camlock handle and screw inward

an additional one half turn. Rotate the handle to

clamp the tube. Recheck for tube tightness and

repeat if necessary.

(Fig. 4)

Fig. 2

Fig. 4

• Operator’s Manual

• Upper and Middle Handles

• Trimmer Guard

• Spark Plug Wrench

• Replacement String Tube and Clips

• 50:1 2-Cycle Engine Oil (2.6 Fluid Ounces.)

• Front Tube with Trimmer Head

• (2) Wheel Assemblies

• (4) Plastic Wing Nuts (For Attaching Handles)

• (4) Saddle Bolts (For Attaching Handles)

• (2) Cable Ties

• (1) Wheel Shoulder Bolt (Longer for Right Side Wheel)

• (1) Wheel Shoulder Bolt (Shorter for Left Side Wheel)

• (1) Wheel Spacer (For Right Side Wheel)

• (1) Hex Head Cap Screw (For Attaching Trimmer Guard)

MIDDLE

HANDLE

UPPER

HANDLE

Fig. 1

Fig. 3

CUTTING HEAD

ASSEMBLY

MIDDLE

HANDLE

SHORT HANDLE

HEIGHT HOLE

TALL HANDLE

HEIGHT HOLE

LOWER

HANDLE

Assembly (Continued)

• Save all instructions

Wheel Assembly:

D

String Storage:

E

1. Install the right wheel to the frame using the longer

shoulder screw and spacer. Tighten to 25 ft. lbs.

(34 N.m) torque using a 14 mm wrench. (Fig. 9-10)

2. Install the left wheel to the adjuster assembly stud

using the shorter shoulder screw. Tighten to 25 ft. lbs.

(34 N.m) torque. (Fig. 11 & 12)

3. Move the bevel handle to the low position for

level mowing.

1. Snap the lower tube clip onto the left middle handle

using the pierced hole. (Fig. 12)

2. Snap the upper tube clip onto the left middle handle

above using the pierced hole.

3. Install the clear tube with provided extra string

into the clips. (Fig. 13)

Fig. 12

TUBE CLIP

Fig. 13

UPPER

CLIP

TOP CAP

LOWER

CLIP

Debris Guard:

C

1. Insert the tab on the metal mounting bracket into the

slot on the debris guard.

(Fig. 5-6)

2. Install the hex head cap screw through the bracket

and into the metal insert of the debris guard.

Tighten securely using a 10 mm wrench.

(Fig. 7-8)

The trimmer line knife attached to the debris guard is

sharp and can cut you. Handle with care.

CAUTION

SLOT FOR

BRACKET TAB

DEBRIS

GUARD

HEX HEAD

CAP SCREW

HEX HEAD

CAP SCREW

METAL MOUNTING

BRACKET

METAL MOUNTING

BRACKET

Fig. 5

Fig. 7

Fig. 6

Fig. 8

SPACER

Fig. 9

Fig. 11

Fig. 10

Fig. 12

SHOULDER

SCREW

(SHORTER)

BEVEL

HANDLE

SHOULDER

SCREW

ADJUSTER

ASSEMBLY

Operation

• Save all instructions

Control Identification and Use:

A

Recommendations:

B

1. Your Trimmer performs best when the engine

operates at high speed and the tips of the line cut the

vegetation. Do not force the trimmer line into grass

faster than the Trimmer’s cutting speed permits.

2. The tips of the line can cause damage to trees, shrubs

and fences. To avoid damage in these conditions, you

may choose to run the engine at lower speeds and

should carefully monitor the location of the cutting line.

3. Because the cutting head can be pivoted to the right

side, plan to trim objects (fences, buildings, etc.)

in a clockwise manner.

4. When trimming next to wire type fencing, avoid

cutting-line contact with the fence. Contact will

result in rapid line wear. Likewise, contact with

concrete and brick surfaces will result in rapid

line wear.

Thoroughly inspect the area where the Trimmer is to be used and remove all foreign objects. Your equipment can throw

small objects at high speed causing personal injury or property damage.

Keep all children and bystanders at least 50 ft (15 m) away when operating. Stop machine if anyone enters the area.

WARNING

1. Throttle:

The throttle is located on the top crossbar on the

upper handle. Depressing the lever will increase the

engine speed. At idle speed the clutch is disengaged

and the trimmer head will not turn. As engine speed

is increased, the automatic clutch will engage and

rotate the trimmer head. Upon release, the throttle

lever is spring loaded to return to idle speed. (Fig. 14)

2. Swivel to offset trimmer head:

Your wheeled string trimmer mower is designed

with the ability to offset the trimming head from

a centered position to a right side position. This

is accomplished by depressing the finger control

on the right upper handle. By depressing the finger

control, the head becomes unlocked and can be

swiveled to two positions to the right. Upon release

of the finger control, a pin will lock the trimmer head

into the desired position. Swiveling the trimmer head

allows for easy mowing / trimming around obstacles

such as posts or trees and under fences. (Fig. 15)

3. Bevel trimming adjustment:

The line will normally cut approximate 2 inches

(50 mm) high. When it is desired that the line cut

closer to the ground, a bevel adjustment is available.

A handle is located just in front of the left wheel. This

handle can be deflected outward and rotated to two

different positions. This will position the trimmer head

at an angle and allow the line to cut closer to the

ground. This is especially useful when trimming next

to raised sidewalks or building foundations. (Fig. 16)

4. Start / Stop switch:

An ignition switch is located on the engine air filter

housing. The switch must be in the “On” position

for the engine to run. Moving the switch to the “Off”

position will stop the engine. (Fig. 17)

Fig. 14

Fig. 16

Fig. 15

Fig. 17

Operation (Continued)

• Save all instructions

Starting Engine:

B

Keep all parts of your body away from cutting area, the rotating trimmer lines and hot surfaces.

NOTE: DO NOT depress the throttle lever until engine starts and runs.

NOTE: When the weather gets cold, please allow the engine to warm up at idle for longer period of time,

before engaging to RUN/WARM START position.

WARNING

The 2-cycle engine on your Trimmer requires that fuel and

2-cycle engine oil be pre-mixed before adding to the

trimmer’s fuel tank. To mix the fuel/ 2-cycle oil:

1. Use fresh unleaded gasoline with an octane rating

of 87 or higher. Do not use gasoline containing more

than 10% ethanol.

NOTICE

Use of gasoline containing more than 10% ethanol can

damage Trimmer. Use of non-ethanol gasoline is best.

We recommend the continuous use of a fuel additive/

stabilizer to counteract the effects of ethanol. These

additives also prolong the shelf life of gasoline.

2. Always use 2-cycle oil that meets or exceeds

JASO – FC specifications and is intended for mixing at

a fuel/oil ratio of 50:1

3. Do not use automotive or 2-cycle marine outboard oil.

These will damage your Trimmer’s engine and void

the warranty.

4. Always mix the gasoline and 2-cycle oil in a container

approved for gasoline. Never mix fuel directly in the

trimmer’s fuel tank.

5. Follow instructions on 2-cycle oil container for mixing

fuel. Mix gasoline and 2-cycle oil at a ratio of 50:1.

A mixture with a 50:1 ratio is obtained by mixing

1 gallon (4 liters) of gasoline with 2.6 ounces of oil

(77 ml). After adding oil to gasoline, shake container

momentarily to ensure proper mixing.

6. Mix only enough fuel for your immediate needs.

Do not store pre-mixed fuel.

7. Stop engine and allow to cool before refueling.

8. To fill the Trimmer’s fuel tank with the gasoline/oil

mixture, place the Trimmer upright on the ground or on

a sturdy bench and wipe and any debris from around

the fuel cap.

9. Remove fuel cap slowly and use a funnel to pour the

mixture into the tank, and replace the fuel cap.

10. Avoid spilling fuel or oil. Wipe up all fuel spills.

11. Move at least 10 ft (3 m) away from fueling site

before starting engine.

Before Starting Engine:

A

Mixing Fuel / 2-Cycle Oil

Do not smoke or allow smoking near fuel or the Trimmer. Mix and pour fuel outdoors WHERE THERE ARE NO SPARKS

OR FLAMES.

WARNING

Recommendations (cont.):

B

5. Do not allow the trimmer head metal bowl to ride on top of concrete or asphalt surfaces. This will cause

wear to the metal bowl. The bowl was designed to ride on grass surfaces.

6. It is recommended that the line be replaced when it is worn to approximately ½ the original length. This will

help maintain a high tip speed and result in a clean cut. It is strongly recommended that the engine

cooling air screen be wiped clean at every string change. This will prevent engine overheating.

Operation (Continued)

• Save all instructions

Starting Engine:

C

Starting Engine (cont.):

B

Cold Starting The Engine:

1. Place the Trimmer on a flat surface.

2. Move the ignition switch to the “ON” position.

3. Move the choke lever up to the “COLD

START” position. (Fig. 18)

4. Press the primer bulb slowly 6 times. (Fig. 20)

5. Pull the recoil starter handle sharply until the engine

starts and runs. (Fig. 21)

6. After engine starts and runs for 10-15 seconds, move

choke lever to “RUN/WARM START” position. (Fig. 19)

Starting A Flooded Engine:

1. Place the Trimmer on a flat surface.

2. Move the ignition switch to the “ON” position.

3. Move the choke lever to “RUN/WARM START”

position. (Fig. 19)

4. Fully depress the throttle lever and pull the starter

handle repeatedly until engine starts and runs. This

could require pulling the starter handle many times,

depending on how badly the unit is flooded. (Fig. 21)

5. If the engine still does not start, allow the unit to sit for

about 30 minutes, and repeat step 1-4.

Warm Starting The Engine:

1. Place the Trimmer on a flat surface.

2. Move the ignition switch to the “ON” position.

3. Move the choke lever to “RUN/WARM

START” position. (Fig. 19)

4. Pull the recoil starter handle sharply until the

engine starts and runs. (Fig. 21)

Fig. 18

Fig. 20

Fig. 19

Fig. 21

NOTE: If the unit still doesn’t start, refer to the TROUBLESHOOTING section of this manual.

Stopping The Trimmer:

D

The trimmer head and line will continue to rotate for a few seconds after the engine has stopped.

CAUTION

1. Release the throttle lever and allow the engine to

idle for a few moments.

2. Move the Ignition Switch to the “OFF” position.

WARNING

Techniques / Applications:

F

Thoroughly inspect the area where the Trimmer is to be used and remove all foreign objects. Your equipment can throw

small objects at high speed causing personal injury or property damage.

Your Trimmer is most effective when using the tips of the trimmer line for trimming grass and other vegetation. Do not

force the trimmer line into grass or vegetation faster than Trimmer’s cutting speed permits. Forcing the Trimmer will

cause your Trimmer to be less effective, and may cause the engine to overheat.

Trimming Tip

To extend the life of the trimmer line, keep the trimmer line moist. If not kept moist, the nylon line will become dry and

brittle. Keep extra trimmer line in a container of water. The line will stay flexible and easy to change. A flexible line will

also last longer.

It is recommended that the engine air intake screen be cleaned every time the trimmer line is replaced. Failure to keep

the air intake screen clean may result in overheating and damage to engine.

(See instructions under the Maintenance section)

NOTICE

Operation (Continued)

• Save all instructions

Installing Trimmer Line:

E

WARNING

Use 0.095 or 0.105 inch diameter flexible, nonmetallic

line with Trimmer. Never use alternative cutting members

such as wire or wire-rope, which can become a dangerous

projectile.

For 0.095 and 0.105 Inch Diameter Line: (Fig. 22-25)

1. Stop the engine and remove spark plug lead.

2. Cut two lengths of new trimmer line 16.5 inches long.

Use the instructions on the left handle to gage the

proper cut length.

3. Insert one end of string into the side opening and

route around the rear and out the opposite side

opening. (Fig 22)

4. Pull string so that equal lengths are on each side.

5. While pushing tab inward, route one end back

through side opening and out the front of retainer.

(Fig. 23 and 24)

6. Likewise, route the remaining end through its side

opening and out the front of retainer. (Fig 25)

7. Adjust string so equal lengths extend from retainer.

8. Repeat on opposite side.

Fig. 22

Fig. 24

Fig. 23

Fig. 25

Routine Maintenance

• Save all instructions

Engine Air Intake Screen:

B

Air Filter:

A

Your Trimmer has been equipped with two air filters inside the housing. Accumulated debris and dust in the air filter will

reduce engine performance, increase fuel consumption and increases the risk of engine damage. Clean the air filters

every 5 hours of operation. It may be necessary to clean the air filter more often in dry conditions due to a large amount

of airborn debris.

NOTICE

It is critical that the engine air intake screen be cleaned of debris to maintain acceptable engine temperatures. It is

recommended that the screen be cleaned every time the trimmer string is replaced.

WARNING

Disconnect the spark plug before performing maintenance.

WARNING

1. Before removing air filter cover, brush away any loose

dirt or debris on and around the pre-filter located in

the outer filter housing.

2. Remove air filter by unscrewing the retaining fastener.

(Fig. 28)

3. Remove and clean foam filter. (Fig. 30)

•

Light surface dust can readily be removed by

tapping the filter.

• Heavy deposits should be washed out in soap

and water. Squeeze out any remaining water and

allow the filter to completely dry.

Never clean filter in gasoline or other flammable solvents.

4. Add four drops of thin oil to the foam filter, squeeze

out excess and replace.

5. Remove the paper air filter element. (Fig 31) Clean

filter by gently tapping it on a flat surface. If very dirty,

replace with a new filter.

6. Reassemble the air filter element and air filter cover.

WARNING

Fig. 28

Fig. 30

Fig. 29

Fig. 31

1. Stop the engine and disconnect the spark plug wire.

2. Allow the unit to cool.

3. Using a dry cloth or brush, remove debris from the

screen. The screen is located between the engine and

the fuel tank and is accessible on all sides.

4. The front flexible shield can be deflected for access to

the front screen.

The engine and exhaust system may be hot and can cause skin burns. Allow engine to cool and use caution around

hot surfaces.

Storage

• Save all instructions

NOTICE

To prevent fuel gum deposits and corrosion in the

Trimmer’s carburetor and fuel system, it is highly

recommended to use a fuel additive / stabilizer formulated

for ethanol fuels. Follow the stabilizer manufacturer’s

instructions. Run the engine at least 5 minutes after adding

stabilizer.

1.

Allow engine to cool and empty the fuel tank before

storing or transporting in vehicle. Use up remaining fuel

in the carburetor by starting the engine and letting it run

until it stops. Squeeze primer bulb several times to purge

fuel from the carburetor.

2. When not in use, store Trimmer indoors in a dry

location. Store Trimmer in a locked area out of the

reach of children.

3. Store unit and fuel in area where fuel vapors cannot

reach sparks or open flames from water heaters,

electric motors or switches, furnaces, etc.

4. When preparing the Trimmer for storage or when

Trimmer will not be used for 30 days or more:

a. Inspect and clean the Trimmer thoroughly.

b. Lightly oil all external metal surfaces.

c. Remove the spark plug, place a few drops of

2-cycle engine oil into the cylinder. Pull the recoil

starter several times to distribute the oil. Replace

the spark plug.

d. Inspect and clean air filter as required.

Trimmer Head:

D

1. If the string retention parts become filled with debris,

they can be removed using a 5 mm hex wrench. When

reinstalling, only tighten to 5 N.m and assure the inner

part is free to move.

Spark Plug:

C

Inspect the spark plug after every 10-15 hours of use; adjust spark plug gap and replace spark plug as necessary.

Replace spark plug every year to maintain engine performance and easy starting.

To inspect or replace the spark plug:

1. Remove the insulated spark plug boot.

2. Use the spark plug wrench to remove the spark plug,

by turning counter-clockwise.

3. Clean and adjust the spark plug gap to

0.024 – 0.028 inches (0.6 - 0.7 mm).

4. Replace any worn plug with a recommended

replacement (see PRODUCT SPECIFICATIONS)

Clean and adjust the spark plug gap to

0.024 – 0.028 inches (0.6 - 0.7 mm).

5. Install the spark plug finger tight in the cylinder head,

then tighten firmly with the spark plug wrench.

6. Attach the insulated spark plug boot.

Routine Maintenance

• Save all instructions

2. If it is necessary to remove the trimmer bowl and head

note that the large retaining nut has a left hand thread

(i.e. to remove the nut turn clockwise).

You may have further questions about assembling, operating, or maintaining this Trimmer. If so, you can contact our

Technical Service Department at 1-800-737-2112 (English only).

You may also write to:

METL Corporate Office - CORRESPONDENCE ONLY

ATTN: Technical Service – METL

6700 Wildlife Way

Long Grove, IL 60047

Technical Service

• Save all instructions

When contacting the Technical Service Department, have

ready:

• Your Name

• Your Address

• Your Phone Number

• Model Number of Product

• Date of Purchase (include copy of receipt for written requests)

If you need assistance or have any questions,

CALL TOLL FREE: 1-800–737-2112

PROBLEM POSSIBLE CAUSE(S) SOLUTION(S)

Engine will not start.

1.

Ignition Switch in the “OFF” position.

2. Engine flooded.

3. Fuel Tank empty.

4. Spark Plug not firing.

5. Fuel not reaching carburetor.

6. Carburetor requires adjustment.

1. Move ignition switch to the ON position.

2. See Starting a Flooded Engine in

OPERATION section.

3. Fill tank with correct fuel mixture.

4. Replace Spark Plug.

5. Check for kinked or split fuel line; repair

or replace.

6. Contact a qualified service center.

Engine will not accelerate, lacks

power or stalls.

1.

Grass wrapped around Trimmer Head.

2. Air filter dirty.

3. Spark plug fouled.

4. Carburetor requires adjustment.

5. Carbon build-up on muffler outlet

screen.

6. Compression low.

1.

Clear debris and grass from Trimmer Head.

2. Clean air filter.

3. Clean or replace plug.

4. Contact a qualified service center.

5. Contact a qualified service center.

6. Contact a qualified service center.

Engine smokes excessively.

1. Fuel mixture incorrect.

2. Air filter dirty.

3. Carburetor requires adjustment.

1. Empty Fuel Tank and refill with correct fuel

mixture.

2. Clean or replace air filter.

3. Contact a qualified service center.

Engine runs hot.

1. Fuel mixture incorrect.

2. Spark Plug incorrect.

3. Carburetor requires adjustment.

4. Carbon build-up on muffler outlet

screen.

5. Engine air screen covered

with debris.

1. See Mixing Fuel / 2-Cycle Oil in

OPERATION section.

2. Replace with correct Spark Plug.

3. Contact a qualified service center.

4. Contact a qualified service center.

5. Clean engine cooling air screen.

Engine will not idle properly.

1. Carburetor requires adjustment.

2. Crankshaft seals worn.

3. Compression low.

1. Contact a qualified service center.

2. Contact a qualified service center.

3. Contact a qualified service center.

Troubleshooting

• Save all instructions

Warranty

• Save all instructions

Always specify model number when contacting the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard

written warranty. We make no other warranty, expressed or implied.

MAT Engine Technologies, LLC

warrants this Trimmer

and any parts thereof, to be free from defects in material and workmanship for two years (90 days for reconditioned unit) from

the date of first purchase from an authorized dealer, provided that the product has been properly maintained and operated in

accordance with all applicable instructions. This warranty is extended only to the original retail purchaser. The bill of sales or

proof of purchase must be presented at the time a claim is made under this warranty. This warranty does not cover commercial,

industrial, or rental usage, nor does it apply to parts that are not in original condition because of normal wear and tear, or parts

that fail or become damaged as a result of misuse, accident, lack of proper maintenance, tampering, or alteration. Exceptions

to the standard warranty period would be normal wear items such as cutting line, cutting head, air filters and spark plugs which

are only covered for 60 days against defects in material or workmanship. Travel, handling, transportation, and incidental costs

associated with warranty repairs are not reimbursable under this warranty and are the responsibility of the owner. To the full

extent allowed by the law of the jurisdiction that governs the sale of the product, this express warranty excludes any and all other

expressed warranties and limits the duration of any and all implied warranties, including warranties of merchantability and fitness

for a particular purpose to two years from the date of first purchase, and

MAT Engine Technologies, LLC’s

liability is hereby

limited to the purchase price of the product and

MAT Engine Technologies, LLC

shall not be liable for any other damages

whatsoever including indirect, incidental, or consequential damages. Some states do not allow limitation of how long an implied

warranty lasts or an exclusion or limitation of incidental or consequential damages, so the above limitation of damages may not

apply to you. This warranty provides the original purchaser with specific rights.

For information regarding those rights, please consult the applicable state laws.

METL Corporate Office - CORRESPONDENCE ONLY

ATTN: Technical Service – METL

6700 Wildlife Way

Long Grove, IL 60047

Powermate™ TRIMMER Limited Warranty

If you have any questions regarding your warranty coverage, you

should contact METL customer service:

If you need assistance or have any questions,

CALL TOLL FREE: 1-800–737-2112

The Engine Emissions Control System Warranty is provided by the engine manufacturer, included with this product and administered by

MAT Engine Technologies, LLC.

Page is loading ...

Powermate PWSTM4317 User manual

This manual is also suitable for

Powermate PWSTM4317 User manual

in other languages

Related papers

Other documents