Eurotech ReliaGATE 10-11 Owner's manual

Type
Owner's manual
Original User Manual
ReliaGATE 10-11-x6
Multi-Service Gateway & Edge Controller
Rev. 2-2 30 September 2016 REGATE-10-11-x6_UserMan_EN_2-2 ENGLISH
Trademarks
All trademarks and registered trademarks are the property of their respective owners.
Intended audience
This document is intended for system integrators, who are skilled persons with a thorough knowledge in
bringing together component subsystems into a whole, ensuring that those subsystems function together.
Disclaimer of liability
Eurotech has reviewed the contents of this document to ensure accuracy and consistency with the
hardware and software described.
Always refer to the latest available manual revision available at: www.eurotech.com.
Revision history
Revision Description Date
1-0 First release 25 March 2016
1-1 Updated section "Power features"
Applied minor corrections
13 April 2016
2-0 Updated sections:
"Declaration on Conformity"
"Interfaces in detail"
"How to access the interfaces under Linux"
"How to install the product"
9 September 2016
2-2 Minor updates 30 September 2016
© 2016 Eurotech SpA - Via Fratelli Solari 3/A - 33020 AMARO (UD) - Italy
ReliaGATE 10-11-x6 User Manual Rev 2-2 Table of contents
TABLE OF CONTENTS
Trademarks 2
Intended audience 2
Disclaimer of liability 2
Revision history 2
Table of contents 3
1 Safety Instructions 7
1.1 Signals used in this document 7
1.2 Observe antistatic precautions 8
1.3 Connect power supply correctly 8
2 How to receive technical assistance 9
2.1 How to receive technical support 9
2.2 How to return a product to Eurotech 9
3 Conventions used in this document 11
3.1 Conventions for signal names 11
3.2 Abbreviations for direction and electrical characteristics of a signal 11
4 Getting started 13
5 Product overview 15
5.1 Product labels 16
6 Declaration of Conformity 17
6.1 CE Marking 17
6.2 WEEE compliance 17
6.3 RoHS 2 compliance 17
6.4 Electromagnetic Compatibility 18
6.4.1 Electromagnetic Compatibility (for EU) 18
6.4.2 FCC compliance (for USA) 18
6.4.3 IC Compliance (for Canada) 19
7 Technical Specifications 21
8 Interfaces Overview 23
8.1 Front panel interfaces 23
8.2 Rear panel interfaces 24
8.3 LED indicators 25
8.4 Service panel interfaces 26
8.5 ReliaCELL interface 27
9 Interfaces in detail 29
9.1 Ethernet ports 29
9.1.1 Connectors and mating connectors specifications 29
9.1.2 Connectors pinout 29
9.1.3 Ports specifications 29
9.2 Wi-Fi and Bluetooth 30
9.2.1 Wi-Fi antenna connector specifications 30
9.2.2 Wi-Fi specifications 30
9.2.3 Bluetooth specifications 30
9.2.4 BLE specifications 30
9.3 Digital I/O interfaces 31
9.3.1 Connector and mating connector specifications 31
3 / 76
Table of contents ReliaGATE 10-11-x6 User Manual Rev 2-2
9.3.2 Connector pinout 31
9.4 COM ports 0 and 1 32
9.4.1 Note for termination resistors (for RS-485 mode only) 32
9.4.2 Note for fail safe resistors (for RS-485 mode only) 32
9.4.2.1 Switches meaning 32
9.4.3 Connector and mating connector specifications 33
9.4.4 Connector pinout 33
9.5 CAN ports 0 and 1 34
9.5.1 Connector and mating connector specifications 34
9.5.2 Connector pinout 34
9.6 Host USB ports 0 and 1 35
9.6.1 Connector and mating connector specifications 35
9.6.2 Connector pinout 35
9.7 The MicroSD card receptacle 36
9.8 Console port 37
9.8.1 Connector and mating connector specifications 37
9.8.2 Connector pinout 37
9.9 RTC (Real Time Clock) 38
9.9.1 The RTC device "/dev/rtc1" 38
9.9.2 The RTC battery 38
9.9.2.1 Battery Install / Replacement Instructions 38
9.9.2.2 How to enable / disable the RTC battery 39
9.10 Watchdog 39
9.11 Accelerometer 39
9.12 The Programmable pushbutton 39
10 How to supply power to the product 41
10.1 Power supply specifications 41
10.2 Power connector and mating connector specifications 41
10.2.1 Power connector pinout 41
10.3 How to turn ON the product 41
10.4 How to turn OFF the product 42
10.5 How to manage the power consumption of the product 42
10.6 How to perform a power reset of the product 42
11 The Software 43
11.1 The Linux OS distribution 43
11.2 The bootloader procedure 43
11.2.1 How to select the MLO source 43
11.2.2 How to set up a correct microSD card / eMMC card partition 43
12 How to access the interfaces under Linux 45
12.1 Ethernet ports 45
12.2 Wi-Fi and Bluetooth 45
12.3 Digital I/Os 45
12.3.1 The GPIO utility 45
12.4 COM ports 0 and 1, Console port 47
12.4.1 How to set the RS-232/485 modes 47
12.4.1.1 Use the ethsetserial utility to configure the COM ports 47
12.4.1.2 Implement the ioctl in the source code to configure the COM ports 47
12.4.2 How to test a COM port 49
12.5 CAN Ports 50
12.5.1 How to enable the CAN bus 5V 50
12.5.2 How to setup a CAN port 50
12.5.3 How to send/receive a message via a CAN port 50
12.6 LED indicators 51
12.6.1 How to drive a LED 51
4 / 76
ReliaGATE 10-11-x6 User Manual Rev 2-2 Table of contents
12.7 Flash Memory 51
12.8 Vehicle Ignition Sense 52
12.9 RTC 53
12.9.1 How to use the timestamp registers 53
12.9.2 How to use the user-available byte 53
12.9.3 How to manage the ReliaGATE 10-11-x6 sleep mode (example) 54
12.10 Watchdog 55
12.10.1 Manage the watchdog using the C programming language 55
12.10.2 Manage the watchdog from the command line 55
12.10.3 For further information 56
12.11 Accelerometer 56
12.12 Internal temperature sensor 57
12.13 The Programmable pushbutton 57
13 How to log in the Administration Console 59
13.1 How to login using the Console port 59
13.2 How to login via Secure Shell (SSH) 59
13.2.1 How to login if your development PC is running Linux 59
13.2.1.1 To connect the ReliaGATE 10-11-x6 via its eth0 port 59
13.2.1.2 To connect the ReliaGATE 10-11-x6 via its eth1 port 60
13.2.2 How to login if your development PC is running Windows 60
13.2.2.1 To connect the ReliaGATE 10-11-x6 via its eth0 port 60
13.2.2.2 To connect the ReliaGATE 10-11-x6 via its eth1 port 60
13.3 How to change your security settings 61
14 Eurotech M2M / IoT solutions 63
14.1 Everyware Software Framework (ESF) 63
14.2 The ESF Web UI 63
14.3 Everyware Cloud (EC) 64
14.4 For further information 64
15 Mechanical specifications 65
15.1 ReliaGATE 10-11-x6 mechanical dimensions 65
15.2 Mounting Bracket mechanical dimensions 66
16 How to install the product 67
16.1 Comply with the FCC & Industry Canada RF exposure safety statement 67
16.2 How to install the product using the Mounting Bracket 67
16.3 How to replace the Mounting Bracket with the DIN Rail Mounting Kit 68
16.4 How to replace the DIN Rail Mounting Kit with the Mounting Bracket 69
16.5 How to install the product on a DIN rail 70
16.6 How to remove the product from a DIN rail 70
16.7 How to remove the DIN Mounting Kit from the product 71
16.8 How to install the DIN Mounting Kit on the product 71
16.9 Which screws are used with the Mounting Bracket or the DIN Mounting Kit 72
17 How to Maintain the Product 73
17.1 Use antistatic precautions 73
17.2 Remove the power supply 73
17.3 Inspect the installation of the product 73
17.4 Clean the product 73
Notes 75
5 / 76
(This page has been intentionally left blank)
ReliaGATE 10-11-x6 User Manual Rev 2-2 1 Safety Instructions
1 SAFETY INSTRUCTIONS
CAREFULLY READ AND UNDERSTAND THE INSTRUCTIONS CONTAINED IN THIS
DOCUMENT BEFORE INSTALLING / OPERATING THE PRODUCT.
KEEP THIS DOCUMENT FOR FUTURE REFERENCE.
Whenever you have any doubt regarding the correct understanding of the instructions contained in this
document contact your local Eurotech Technical Support Team (see the last page of this document for
further details).
To lower the risk of personal injury, electric shock, fire or damage to equipment, observe the following
precautions, as well as using good technical judgment, whenever installing / operating the product.
Failure to comply with these instructions or with specific warnings elsewhere in this document violates
safety standards of design and manufacture, and intended use of the product.
Eurotech assumes no liability for any failure to comply with these instructions.
1.1 Signals used in this document
DANGER
INDICATES A HAZARD WITH A HIGH LEVEL OF RISK WHICH, IF NOT AVOIDED, WILL
RESULT IN DEATH OR SERIOUS INJURY
WARNING
INDICATES A HAZARD WITH A MEDIUM LEVEL OF RISK WHICH, IF NOT AVOIDED, COULD
RESULT IN DEATH OR SERIOUS INJURY
CAUTION
INDICATES A HAZARD WITH A LOW LEVEL OF RISK WHICH, IF NOT AVOIDED, COULD
RESULT IN MINOR OR MODERATE INJURY
NOTICE
Indicates practices not related to personal injury, such as:
l An instruction to follow to use the product effectively
l A statement of company policy related to product or property protection
7 / 76
1 Safety Instructions ReliaGATE 10-11-x6 User Manual Rev 2-2
1.2 Observe antistatic precautions
NOTICE
PREVENTING ELECTROSTATIC DISCHARGE (ESD)
When handing the product described in this document, always use appropriate
antistatic precautions to avoid damages due to electrostatic discharge.
For example: use a wrist strap or ESD cuff kept in constant contact with bare skin
and attached to an ESD ground.
1.3 Connect power supply correctly
WARNING
ELECTRIC SHOCK HAZARD
Before applying power, thoroughly review all installation, operation, and safety instructions.
Failure to supply power correctly, or failure to follow all operating instructions correctly, may
create an electric shock hazard, which could result in personal injury or loss of life, and / or
damage to equipment or other property.
To avoid injuries:
l Before operating any equipment, carefully read any supplied instructions
l Do not perform any connections with wet hands
l Check any power cords for damage before using them
l Use certified power cables. The power cables must meet the power requirements of the
device
l Position cables with care. Avoid positioning cables in places where they may be
trampled or compressed by objects placed on them
l Take particular care of plugs, power-points and outlets. Avoid overcharging them
l Always disconnect power and discharge the circuits before touching them
l Only start the product with a power supply that meets the requirements stated on the
voltage label. In case of uncertainties about the required power supply, contact the
Eurotech Technical Support Team (see the back cover for full contact details) or the
electricity authority.
8 / 76
ReliaGATE 10-11-x6 User Manual Rev 2-2 2 How to receive technical assistance
2 HOW TO RECEIVE TECHNICAL ASSISTANCE
2.1 How to receive technical support
If you have technical questions, or if you cannot isolate a problem with your product, or for any inquiry
about repair and returns policies, contact:
l The Eurotech Global Support Center: https://support.eurotech.com/
l Your local Eurotech Technical Support Team: see the back cover for full contact details.
2.2 How to return a product to Eurotech
To return a product to Eurotech, complete the following steps:
1. Send an email to your local Eurotech Technical Support Team (see the back cover for full contact
details) specifying:
l Product Model Number (printed on the product label)
l Product Serial Number (printed on the product label)
l Recap of the fault description
2. Receive a reply from the Eurotech RMA Department. It contains:
l The RMA (Return Merchandise Authorization) number
l The shipping information
3. Pack the product using anti-static material and place it in a sturdy box with enough packing material
to adequately cushion it
4. Ship the product to Eurotech following the information received from the Eurotech RMA
Department.
NOTICE
Any product returned to Eurotech that is found to be damaged due to inappropriate packaging
will not be covered by the warranty!
When shipping the product:
1. Pack it using anti-static material
2. Place it in a sturdy box with enough packing material to adequately cushion it.
9 / 76
(This page has been intentionally left blank)
ReliaGATE 10-11-x6 User Manual Rev 2-2 3 Conventions used in this document
3 CONVENTIONS USED IN THIS DOCUMENT
3.1 Conventions for signal names
Convention Description
GND Digital ground plane
# Active low signal
_P Positive signal in differential pair
_N Negative signal in differential pair
3.2 Abbreviations for direction and electrical characteristics of
a signal
Convention Description
I Signal is an input to the system
O Signal is an output from the system
IO Signal may be input or output
P Power and ground
A Analog signal
3.3 3.3 V signal level
5 5 V signal level
NC No Connection
Reserved Use is reserved to Eurotech
11 / 76
(This page has been intentionally left blank)
ReliaGATE 10-11-x6 User Manual Rev 2-2 4 Getting started
4 GETTING STARTED
To get started with the ReliaGATE 10-11-x6, follow these steps:
1. Know the ReliaGATE 10-11-x6 interfaces.
The ReliaGATE 10-11-x6 provides connectivity to several wired and wireless interfaces.
For further information, see:
l "Product overview" on page 15
l "Declaration of Conformity" on page 17
l "Technical Specifications" on page 21
l "Interfaces Overview" on page 23
l "Interfaces in detail" on page 29
2. Supply power to the ReliaGATE 10-11-x6.
Supply power to the ReliaGATE 10-11-x6 correctly, respecting all the safety instructions..
For further information, see "How to supply power to the product" on page 41
3. Log into the Administration console.
The ReliaGATE 10-11-x6 runs a Linux distribution based on a Yocto framework and supports login
via a variety of methods.
For further information, see:
l "The Software" on page 43
l "How to log in the Administration Console" on page 59
l "How to access the interfaces under Linux" on page 45
4. Start developing your applications.
The ReliaGATE 10-11-x6 supports ESF, which is an inclusive software framework that puts a
middleware layer between the operating system and the OEM application.
For detailed instructions, and sample applications for developing device applications using ESF on
Eurotech platforms, see: http://esf.eurotech.com/docs.
5. Install the ReliaGATE 10-11-x6.
The ReliaGATE 10-11-x6 is lightweight, compact, and easy to install.
For further information, see:
l "Mechanical specifications" on page 65
l "How to install the product" on page 67
6. Maintain the ReliaGATE 10-11-x6.
Periodic maintenance of the ReliaGATE 10-11-x6 ensures greater integrity and reliable operation.
For further information, see:
l "How to Maintain the Product" on page 73
13 / 76
(This page has been intentionally left blank)
ReliaGATE 10-11-x6 User Manual Rev 2-2 5 Product overview
5 PRODUCT OVERVIEW
Your ReliaGATE 10-11-x6 is a compact and lightweight device intended to be used as IoT gateway. It is
based on the TI AM335X Cortex-A8 (Sitara) processor family, with 512MB of RAM, 4GB of eMMC, and a
user-accessible microSD slot.
It is suitable for intensive workload in industrial and automotive applications. It supports a 9 to 36 V power
supply with transient protection and vehicle ignition sense, and features a wide range of connectivity
capabilities.
Your ReliaGATE 10-11-x6 can be equipped with Everyware™ Software Framework (ESF), a commercial,
enterprise-ready edition of Eclipse Kura, the open source Java/OSGi middleware for IoT gateways.
Your ReliaGATE 10-11-x6 can also take advance of Everyware Cloud (separately available). Everyware
Cloud (EC) is a specialized cloud solution that allows you to easily connect, configure and manage your
device through all its life-cycle.
A Development Kit is available upon request. It allows you to quickly and easily start the development of
your applications.
Figure 5.1 - The ReliaGATE 10-11-x6
15 / 76
5 Product overview ReliaGATE 10-11-x6 User Manual Rev 2-2
5.1 Product labels
The product labels are placed on the bottom side of the product
1
.
Ref#
Label content
Label example
1
Eurotech logo
E-mark
ReliaGATE model number
MAC address in bar-code format
MAC address
Power supply specifications
2
FCC ID numbers
ReliaGATE serial number in bar-code format
ReliaGATE serial number
CE mark
WEEE symbol
1
For clarity, the figure above does not show the DIN mounting kit.
16 / 76
ReliaGATE 10-11-x6 User Manual Rev 2-2 6 Declaration of Conformity
6 DECLARATION OF CONFORMITY
6.1 CE Marking
This product is CE marked.
The product meets the guidelines listed in the following sections.
Eurotech is not responsible for the use of this product together with equipment (e.g. power
supplies, personal computers, etc.) that are not CE marked and compliant with the
requirements specified in this document.
This product is compliant with:
l Reduction of Certain Hazardous Substances (RoHS2)
l IP40
l CE
l IEC/UL 60950-1 Information Technology Equipment - Safety - Part 1: General Requirements
l Product compliance with part 15.21 of FCC
The Wi-Fi / Bluetooth Radio module is compliant with:
l CE - EN300 328 (2.4GHz ISM), EN50371 (EMI), EN301 489 (EMC)
l FCC - 15.209 (General RF device), 15.247 & 15.249 (2.4GHz ISM)
l IC for Canada
6.2 WEEE compliance
In compliance with the Directive 2012/19/EU of the European Parliament and of the Council
of 4 July 2012 on waste electrical and electronic equipment (WEEE), the symbol on the
right, shown on the product or within its literature, indicates separate collection for this
electrical and electronic equipment (EEE) that has been placed on the market after 2005.
This product, at the end of its life cycle, must be collected separately and managed in
accordance with the provisions of the current Directive on waste electrical and electronic
equipment.
Because of the substances present in the product, improper use or disposal of the refuse
can cause damage to human health and the environment.
To avoid any possible legal implications, contact your local waste collection body for full
recycling information.
6.3 RoHS 2 compliance
The product described in this document, including all its components and its sub-assemblies, have been
manufactured in compliance with the Directive 2011/65/EU of the European Parliament and of the Council
of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic
equipment.
17 / 76
6 Declaration of Conformity ReliaGATE 10-11-x6 User Manual Rev 2-2
6.4 Electromagnetic Compatibility
6.4.1 Electromagnetic Compatibility (for EU)
Conditions of operation
This product meets the requirements of the EC Directive 2004/108/EC on the electromagnetic
compatibility.
This product is designed for use in industrial areas.
Modifications
Any modifications made to this product that are not approved by Eurotech may void the prerequisites for
the EC conformity declaration.
6.4.2 FCC compliance (for USA)
This device and its accessories comply with part 15 of FCC rules. Operation is subject to the following two
conditions:
1. This device and its accessories may not cause harmful interference.
2. This device and its accessories must accept any interference received, including interference that
may cause undesired operation.
Change or modifications that are not expressly approved by the manufacturer could void the user's
authority to operate the equipment.
FCC ID: UKMMRG1011
Contains FCC ID: RI7HE910
18 / 76
ReliaGATE 10-11-x6 User Manual Rev 2-2 6 Declaration of Conformity
6.4.3 IC Compliance (for Canada)
ENGLISH
This device complies with Industry Canada's
license-exempt RSSs. Operation is subject to the
following two conditions:
1. This device may not cause interference;
and
2. This device must accept any interference,
including interference that may cause
undesired operation of the device.
FRANÇAIS
Le présent appareil est conforme aux CNR
d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes:
1. L'appareil ne doit pas produire de
brouillage;
2. L'utilisateur de l'appareil doit accepter tout
brouillageradioélectrique subi, même si le
brouillage est susceptible d'en
compromettre le fonctionnement.
This radio transmitter IC: 21442-MRG1011 has
been approved by Industry Canada to operate
with the antenna types listed below with the max-
imum permissible gain indicated. Antenna types
not included in this list, having a gain greater than
the maximum gain indicated for that type, are
strictly prohibited for use with this device.
Le présent émetteur radio IC: 21442-MRG1011 a
é approuvé par Industrie Canada pour fonc-
tionner avec les types d'antenne énumérés ci-des-
sous et ayant un gain admissible maximal. Les
types d'antenne non inclus dans cette liste, et
dont le gain est supérieur au gain maximal
indiqué, sont strictement interdits pour l'ex-
ploitation de l'émetteur.
Antenna types / Types d’antenne Gain / Gain
Cellular
GSM 850 -0.23 dBi
GSM 900 0.77 dBi
DCS 0.67 dBi
PCS 0.96 dBi
WCDMA I 0.73 dBi
Wi-Fi / Bluetooth 5.0 dBi
IC: 21442-MRG1011
Contains IC: 5131A-HE910
19 / 76
(This page has been intentionally left blank)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

Eurotech ReliaGATE 10-11 Owner's manual

Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI