American Standard 0403.004.222 Operating instructions

Brand: American Standard

Model: 0403.004.222

Type: Operating instructions

J13

Revised 11/09

TROPIC PETITE

PEDESTAL SINK

VITREOUS CHINA

TROPIC PETITE PEDESTAL SINK

• Vitreous china

• Contemporary styled lavatory and pedestal

• Rear overow

• Supplied with mounting kit

• Right Height

for greater comfort during use

• Faucet ledge with large deck area

• Recommended Tropic faucets 7038.801

Widespread (illustrated) and 7038.201

Centerset not included

• Basin has at bottom to also allow use as an

above counter sink or a countertop sink

• Recommended with 9212.030 Tropic 30" vanity

and 9212.124 Marble Top

• Style coordinates with Tropic Cadet

3 toilets

❏ 0403.800 Faucet holes on 203mm (8") centers

(Illustrated)

❏ 0403.400 Faucet holes on 102mm (4") centers

Nominal Dimensions:

531 x 470 x 915mm

(21" x 18-1/2" x 36")

❏ 0403.008 Lavatory slab-203mm (8") centers

❏ 0403.004 Lavatory slab-102mm (4") centers

❏ 0010.000 Pedestal only

Bowl sizes:

445mm (17-1/2") wide,

292mm (11-1/2") front to back,

152mm (5-1/2") deep

Compliance Certications -

Meets or Exceeds the Following Specications:

• ASME A112.19.2 - 2008/CSA B45.1-08

To Be Specied:

❏ Color: ❏ White ❏ Bone ❏ Linen ❏ Black

❏ Faucet: ❏ 7038.801 Tropic Widespread

❏ 7038.201 Tropic Centerset

❏ Faucet Finish:

❏ 002 Polished Chrome

❏ 295 Satin Nickel

❏ Supplies:

❏ 1-1/4" Trap:

❏ Nipple:

* See faucet section for additional models available

SEE REVERSE FOR ROUGHING-IN DIMENSIONS

J14

TROPIC PETITE

PEDESTAL SINK

VITREOUS CHINA

FINISHED

WALL

470mm

(18-1/2)

82mm

(3-1/4)

13mm

(1/2)

213mm

(8-1/2)

203mm

(8)

254mm

(10) REF.

203mm (8)

191mm

(7-1/2)

*635mm

(25)

13mm

(1/2) DIA.

HOLES FOR

ANCHOR BOLTS

*590mm

(23-1/4)

9-1/2mm (3/8) DIA

BASE ANCHOR

SCREW HOLES

1-1/4

O.D.

WASTE

830mm

(32-3/4)

1-1/4 OD

TAILPIECE

915mm

(36)

FINISHED

FLOOR

170mm

(6-3/4)

PEDESTAL

SIDE SECTION

760mm

(30)

OPEN TO

FLOOR

DRAIN

CHASE

531mm

(21)

SUPPLIES

REQUIRED

COUNTERTOP

FINISHED FLOOR

FINISHED

WALL

165mm

(6-1/2)

787mm

(31)

610mm

(24)

127mm

(5)

864mm

(34)

686mm

(27)

203mm

(8)

152mm

(6)

229mm

(9)

NOTES:

DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAPS

ARE SUGGESTED.

▼ PEDESTAL ANCHORING SCREWS NOT INCLUDED.

■ SUITABLE FOR REINFORCEMENT ONLY. ACTUAL DIMENSIONS MUST

BE TAKEN FROM FIXTURE.

FITTING NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.

INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.

IMPORTANT: Dimensions of xtures are nominal and may vary within the

range of tolerance established by ANSI Standard A112.19.2

These measurements are subject to change or cancellation. No responsibility

is assumed for use of superseded or voided pages.

Revised 11/09

American Standard 0403.004.222 Operating instructions

American Standard 0403.004.222 Operating instructions

American Standard 0403.004.222 Operating instructions

Related papers

Other documents