CAUTION:
Read all safety and
operating instructions
before using this
equipment
OWNER’S MANUAL &
SETUP INSTRUCTIONS
ATS Stand
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 2
ATS STAND (Document Part Number 158474)
The MK Diamond ATS Stand is designed for use with the following MK Diamond products – MK-100, (Part No.
158189), MK-101 (Part No. 151991), MK-101Pro (Part No. 155747), MK-101 Pro24 (Part No. 153243), MK-115
Pro24 (Part No. 150341), MK-880 (Part No. 153261), MK-1080 (Part No. 153203), MK-2001 (Part No. 150597),
and MK-2002 (Part No. 150598),
NOTE: If problems arise during the assembly of the ATS Stand, contact the MK Diamond Service Center –
(800) 474-5594
CONTENTS:
one (1) ATS stand frame, one (1) ATS stand support plate, two (2) inflatable tires, two (2) tire retaining caps, one
(1) rear stop/register – A bracket, two (2) B brackets, three (3) C brackets, four (4) D brackets, two (2) F
brackets, six (6) hex-head bolts, six (6) nylock nuts.
ATS Stand
Frame
ATS Stand
Support Plate
Inflatable
Tires (2ea)
Shaft Sleeves
(2ea)
Tire Retaining
Caps (2ea)
Rear Stop/Register,
Bracket A (1 ea)
Bracket B
(101 series 2ea)
Bracket C (101 &
1080 series 3ea)
Bracket D (2000
series -4ea)
Bracket F (1080
series – 2ea)
Hex-head Bolts
(6ea)
Nylock Nuts
(6ea)
Thumbscrews
(2ea)
Tools Needed:
9/16-inch
Wrench
9/16-inch Ratchet
with Extension
Hammer Adjustable Wrench
(optional)
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 3
ATS STAND (Document Part Number 158474)
Stand Assembly:
NOTE: Once the Tire Retaining Cap is installed, it is not easily removed. Ensure the Shaft Sleeve is installed
and the tire is correctly oriented before performing Step D.
ATS Stand Setup:
u
Axle
Shaft Sleeve
(D)
Position the Tire Retaining
Cap on the axle
(E)
Using a hammer, seat the
Tire Retaining Cap using
gentle taps
(B)
Loosen the two Front Leg
Retaining Knobs
(C)
Verify the Retaining Knob is
Loose (Do not remove the
Retaining Knob)
(A)
Position the ATS Stand in an
upright position
ATS Stand
upright
Rotate counter-
clockwise to loosen
Axle
Tire
Retaining
Cap
Tire
Retaining
Cap
Use gentle
taps to seat
(F)
Repeat Steps A through D
on the opposite side of
the ATS Stand
Retaining
Knob
(A)
Place the ATS Stand on its
side and locate the axle
(B)
Slide one Shaft Sleeve
over the axle
Valve Stem
Axle
Tire
(C)
Insert the tire onto the axle with
the valve stem facing out
Verify the Retaining
Knob is loose
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 4
ATS STAND (Document Part Number 158474)
(G)
Rotate the Rear Leg down and
Tighten the Retaining Knobs
(E)
Loosen the two Rear Leg
Retaining Knobs
(H)
Place ATS Stand on legs
Retaining
Knob
Rotation
Direction
Rotate Knob
clockwise
to tighten
Rear Leg
Rear Leg
Front Leg
Rotate counter-
clockwise to loosen
(I)
Install the ATS Stand Support
Plate Thumbscrews
Thumbscrew
(D)
Rotate Front Leg up and
tighten the Retaining Knobs
Rotation
Direction
Rotate Knob clockwise
to tighten
Front Leg
(F)
Verify the Retaining Knob is
Loose (Do not remove the
Retaining Knob)
Verify the Retaining
Knob is loose
Rotate
clockwise
to install
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 5
ATS STAND (Document Part Number 158474)
MK-100, 101, and 101 Pro Normal Cutting Head Position Installation:
To ensure stability, verify front and rear legs of the ATS Stand are fully extended outward before
installing the saw.
NOTE: The following Brackets are required for fastening the saw to the ATS Stand -
(B)
Remove the Cutting Head
(See the saw Owners Manual)
(C)
Verify ATS Stand legs are
fully extended for stability
(A)
Remove Water Pan
(E)
Install the Bracket A and a Bolt
into the top, rear, of the ATS
Stand as shown
(F)
Install one C Bracket and a Bolt
into the top, rear, of the ATS
Stand as shown
(D)
Seat the saw on the ATS
Stand as shown
(H)
Install one B Bracket and a Bolt
into the front, side, of the ATS
Stand as shown
(G)
Verify the rear brackets are
installed correctly
Removal
Direction
Install into rear hole
on right side of stand
(I)
Install one B Bracket and a Bolt
into the rear, side, of the ATS
Stand as shown
Remove
Cutting Head
Extend legs
outward
Back of saw
Back of ATS Stand
Bracket
A
Install into rear hole
on left side of stand
Bracket
C
Fit bracket
over saw frame
Bracket
C
Bracket
A
Fit bracket
over saw frame
Bracket
B
Install into front hole
on left side of stand
Bracket
B
Fit bracket
over saw frame
Install into middle hole
on left side of stand
2
C Brackets
2
B Brackets
1
A Bracket
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 6
ATS STAND (Document Part Number 158474)
(K)
Verify all brackets are installed
(J)
Install one C Bracket and a Bolt
into the top, front, of the ATS
Stand as shown
(L)
Install one Nylock nut on the Bolt
of each bracket
(Do not cross-thread the nut)
(N)
Install the Cutting Head
(See the saw Owners Manual)
(M)
Using a 9/16-wrench and socket,
tighten all Bolts
(O)
Install the Water Pan
(Q)
Orient and install the ATS
Stand Support Plate as shown
(P)
Locate the ATS Stand Support
Plate retaining tubes on the back
of the ATS Stand
(R)
Tighten the ATS Stand Support
Plate retaining thumbscrews
as shown
(S)
Setup Complete
Install into front hole
on right side of stand
Fit bracket
over saw frame
Bracket
C
Bracket
locations
Rotate clockwise
to install
Nylock
nuts
Rotate
clockwise
to tighten
Install
Cutting Head
Installation
Direction
Retaining
Tubes
ATS Stand
Support Plate
Retaining
Thumbscrew
Rotate
clockwise
to tighten
(T)
Ensure all bolts are
tight before placing the ATS Stand
in the transport position
Transport
Position
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 7
ATS STAND (Document Part Number 158474)
MK-100, 101, and 101 Pro Extended Cutting Head Position Installation:
To ensure stability, verify front and rear legs of the ATS Stand are fully extended outward before
installing the saw.
NOTE: The following Brackets are required for fastening the saw to the ATS Stand -
(B)
Remove the Cutting Head
(See the saw Owners Manual)
(C)
Verify ATS Stand legs are
fully extended for stability
(A)
Remove Water Pan
(E)
Install the Bracket A and a Bolt
into the top, rear, of the ATS
Stand as shown
(F)
Install one C Bracket and a Bolt
into the top, rear, of the ATS
Stand as shown
(D)
Seat the saw on the ATS
Stand as shown
(H)
Install one B Bracket and a Bolt
into the front, side, of the ATS
Stand as shown
(G)
Verify the rear brackets are
installed correctly
Removal
Direction
(I)
Install one B Bracket and a Bolt
into the rear, side, of the ATS
Stand as shown
Remove
Cutting Head
Extend legs
outward
Back of saw
Back of ATS Stand
Bracket
A
Bracket
C
Fit bracket
over saw frame
Bracket
C
Bracket
A
Fit bracket
over saw frame
Bracket
B
Install into front hole
on left side of stand
Bracket
B
Fit bracket
over saw frame
Install into middle hole
on left side of stand
Install into second hole from
the end on right side of stand
Install into second hole from
the end on left side of stand
2
C Brackets
2
B Brackets
1
A Bracket
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 8
ATS STAND (Document Part Number 158474)
(T)
Ensure all bolts are
tight before placing the ATS Stand
in the transport position
(K)
Verify all brackets are installed
(J)
Install one C Bracket and a Bolt
into the top, front, of the ATS
Stand as shown
(L)
Install one Nylock nut on the
Bolt of each bracket
(Do not cross-thread the nut)
(N)
Install the Cutting Head
(See the saw Owners Manual)
(M)
Using a 9/16-wrench and socket,
tighten all Bolts
(O)
Install the Water Pan
(Q)
Orient and install the ATS
Stand Support Plate as shown
(P)
Locate the ATS Stand Support
Plate retaining tubes on the back
of the ATS Stand
(R)
Tighten the ATS Stand Support
Plate retaining thumbscrews
as shown
(S)
Setup Complete
Fit bracket
over saw frame
Bracket
C
Bracket
locations
Rotate clockwise
to install
Nylock
nuts
Rotate
clockwise
to tighten
Install
Cutting Head
Installation
Direction
Retaining
Tubes
ATS Stand
Support Plate
Retaining
Thumbscrew
Rotate
clockwise
to tighten
Install into front hole
on right side of stand
Transport
Position
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 9
ATS STAND (Document Part Number 158474)
Transport the MK-100, 101, and 101 Pro using the ATS Stand:
Setup/Takedown of the MK-100, 101, 101 Pro and ATS Stand:
Ensure all bolts are tight before repositioning the ATS Stand.
Transport
Position
(A)
ATS Stand in Transport Position
(B)
Transport the ATS Stand by the
front of the saw frame or by the
ATS Stand handle
Front of
Saw Frame
ATS Stand
Handle
(A)
Rest ATS Stand on the
Support Plate
ATS Stand
Support Plate
(B)
Loosen the two Front Leg
Retaining Knobs
(C)
Rotate Front Leg up and
tighten the Retaining Knobs
Retaining
Knob
Rotate Knob clockwise
to tighten
Front Leg
Rotate counter-
clockwise to loosen
Rotation
Direction
(E)
Rotate the Rear Leg down and
Tighten the Retaining Knobs
(D)
Loosen the two Rear Leg
Retaining Knobs
Rotate counter-
clockwise to loosen
Retaining
Knob
Rotate Knob
clockwise
to tighten
Rear Leg
(F)
Use proper lifting
techniques when repositioning
the ATS Stand
Reposition
ATS Stand
Rotation
Direction
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 10
ATS STAND (Document Part Number 158474)
To ensure stability, verify front and rear legs of the ATS Stand are fully extended outward before
installing the saw.
NOTE: When work is complete, place the ATS Stand in the transport position by following steps A through J in
reverse order.
Retaining
Thumbscrew
(G)
Verify ATS Stand legs are
fully extended for stability
Extend legs
outward
(H)
Loosen the ATS Stand Support
Plate retaining thumbscrews
as shown
Rotate counter-
clockwise to loosen
(I)
Remove the ATS Stand
Support Plate as shown
ATS Stand
Support Plate
(J)
Install the ATS Stand Support
Plate into the right side of the
ATS Stand as shown
ATS Stand
Support Plate
(K)
Setup the saw for normal
operation in accordance with
the saw Owners Manual
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 11
ATS STAND (Document Part Number 158474)
MK-101 Pro and MK-115 Pro:
To ensure stability, verify front and rear legs of the ATS Stand are fully extended outward before
installing the saw.
NOTE: The following Brackets are required for fastening the saw to the ATS Stand -
(B)
Remove the Cutting Head
(See the saw Owners Manual)
(C)
Verify ATS Stand legs are
fully extended for stability
(A)
Remove Water Pan
(E)
Install the Bracket A and a Bolt
into the top, rear, of the ATS
Stand as shown
(F)
Install one C Bracket and a Bolt
into the top, rear, of the ATS
Stand as shown
(D)
Seat saw on the ATS
Stand as shown
(H)
Install one B Bracket and a Bolt
into the front, side, of the ATS
Stand as shown
(G)
Verify the rear brackets are
installed correctly
Removal
Direction
(I)
Install one B Bracket and a Bolt
into the rear, side, of the ATS
Stand as shown
Remove
Cutting Head
Extend legs
outward
Back of saw
Back of ATS Stand
Bracket
A
Bracket
C
Fit bracket
over saw frame
Bracket
C
Bracket
A
Fit bracket
over saw frame
Bracket
B
Install over front hole
on left side of stand
Bracket
B
Fit bracket
over saw frame
Install into second hole from
the end on right side of stand
Install into second hole from
the end on left side of stand
2
C Brackets
2
B Brackets
1
A Bracket
Install into rear hole
on left side of stand
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 12
ATS STAND (Document Part Number 158474)
(T)
Ensure all bolts are
tight before placing the ATS Stand
in the transport position
(K)
Verify all brackets are installed
(J)
Install one C Bracket and a Bolt
into the top, front, of the ATS
Stand as shown
(L)
Install one Nylock nut on the
Bolt of each bracket
(Do not cross-thread the nut)
(N)
Install the Cutting Head
(See the saw Owners Manual)
(M)
Using a 9/16-wrench and socket,
tighten all Bolts
(O)
Install the Water Pan
(Q)
Orient and install the ATS
Stand Support Plate as shown
(P)
Locate the ATS Stand Support
Plate retaining tubes on the back
of the ATS Stand
(R)
Tighten the ATS Stand Support
Plate retaining thumbscrews
as shown
(S)
Setup Complete
Fit bracket
over saw frame
Bracket
C
Rotate clockwise
to install
Nylock
nuts
Rotate
clockwise
to tighten
Install
Cutting Head
Installation
Direction
Retaining
Tubes
ATS Stand
Support Plate
Retaining
Thumbscrew
Rotate
clockwise
to tighten
Install into front hole
on right side of stand
Transport
Position
Bracket
locations
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 13
ATS STAND (Document Part Number 158474)
Transport the MK-101 Pro and MK-115 Pro using the ATS Stand:
Setup/Takedown of the MK-101 Pro, MK-115 Pro and ATS Stand:
Ensure all bolts are tight before repositioning the ATS Stand.
Transport
Position
(A)
ATS Stand in Transport Position
(B)
Transport the ATS Stand by the
front of the saw frame or by the
ATS Stand handle
Front of
Saw Frame
ATS Stand
Handle
(A)
Rest ATS Stand on the
Support Plate
ATS Stand
Support Plate
(B)
Loosen the two Front Leg
Retaining Knobs
(C)
Rotate Front Leg up and
tighten the Retaining Knobs
Retaining
Knob
Rotate Knob clockwise
to tighten
Front Leg
Rotate counter-
clockwise to loosen
Rotation
Direction
(E)
Rotate the Rear Leg down and
tighten the Retaining Knobs
(D)
Loosen the two Rear Leg
Retaining Knobs
Rotate counter-
clockwise to loosen
Retaining
Knob
Rotate Knob
clockwise
to tighten
Rear Leg
(F)
Use proper lifting
techniques when repositioning
the ATS Stand
Reposition
ATS Stand
Rotation
Direction
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 14
ATS STAND (Document Part Number 158474)
To ensure stability, verify front and rear legs of the ATS Stand are fully extended outward before
installing the saw.
NOTE: When work is complete, place the ATS Stand in the transport position by following steps A through J in
reverse order.
Retaining
Thumbscrew
(G)
Verify ATS Stand legs are
fully extended for stability
Extend legs
outward
(H)
Loosen the ATS Stand Support
Plate retaining thumbscrews
as shown
Rotate counter-
clockwise to loosen
(I)
Remove the ATS Stand
Support Plate as shown
ATS Stand
Support Plate
(J)
Install the ATS Stand Support
Plate into the right side of the
ATS Stand as shown
ATS Stand
Support Plate
(K)
Setup the saw for normal
operation in accordance with
the saw Owners Manual
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 15
ATS STAND (Document Part Number 158474)
MK-1080 and MK-880:
To ensure stability, verify front and rear legs of the ATS Stand are fully extended outward before
installing the saw.
NOTE: The following Brackets are required for fastening the saw to the ATS Stand -
(F)
Verify the rear bracket is
installed correctly
3
C Brackets
(B)
Remove the Cutting Table
(See the saw Owners Manual)
(C)
Verify ATS Stand legs are
fully extended for stability
(A)
Remove Water Pan
(E)
Install the Bracket A and a Bolt
into the top, rear, of the ATS
Stand as shown
(D)
Seat saw on the ATS
Stand as shown
(H)
Install one F Bracket and a Bolt
into the front, side, of the ATS
Stand as shown
(G)
Install one F Bracket and a Bolt
into the rear, side, of the ATS
Stand as shown
Removal
Direction
(I)
Verify the two F Brackets
are installed correctly
Extend legs
outward
Back of saw
Back of ATS Stand
Bracket
A
Bracket
F
Fit bracket
over saw frame
Install into front hole
on left side of stand
Bracket
F
Install into second hole from
the end on right side of stand
2
F Brackets
1
A Bracket
Remove
Cutting Table
Fit bracket
over saw frame
Install into middle hole
on left side of stand
Bracket
F
Bracket
A
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 16
ATS STAND (Document Part Number 158474)
(S)
Install the Cutting Table
(See the saw Owners Manual)
Install
Cutting Table
(T)
Setup Complete
(R)
Tighten the ATS Stand Support
Plate retaining thumbscrews
as shown
Retaining
Thumbscrew
Rotate
clockwise
to tighten
(Q)
Orient and install the ATS
Stand Support Plate as shown
ATS Stand
Support Plate
(K)
Install one C Bracket and a Bolt
into the top, rear, of the ATS
Stand as shown
(J)
Install one C Bracket and a Bolt
into the top, front, of the ATS
Stand as shown
(L)
Verify all brackets are installed
(N)
Using a 9/16-wrench and socket,
tighten all Bolts
(M)
Install one Nylock nut on the
Bolt of each bracket
(Do not cross-thread the nut)
(O)
Install Water Pan
(P)
Locate the ATS Stand Support
Plate retaining tubes on the back
of the ATS Stand
Fit bracket
over saw frame
Bracket
C
Rotate
clockwise
to tighten
Installation
Direction
(U)
Ensure all bolts are
tight before placing the ATS Stand
in the transport position
Transport
Position
Install into top
rear hole on
right side of stand
Install into top
hole on right side
of stand
Bracket
C
Fit bracket
over saw frame
Bracket
locations
Nylock
nuts
Rotate clockwise
to install
Retaining
Tubes
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 17
ATS STAND (Document Part Number 158474)
Transport the MK-1080 and MK-880 using the ATS Stand:
Setup/Takedown of the MK-1080, MK-880 and ATS Stand:
Ensure all bolts are tight before repositioning the ATS Stand.
Transport
Position
(A)
ATS Stand in Transport Position
(B)
Transport the ATS Stand by the
front of the saw frame or by the
ATS Stand handle
Front of
Saw Frame
ATS Stand
Handle
(A)
Rest ATS Stand on the
Support Plate
(B)
Loosen the two Front Leg
Retaining Knobs
(C)
Rotate Front Leg up and
tighten the Retaining Knobs
Retaining
Knob
Rotate Knob clockwise
to tighten
Front Leg
Rotate counter-
clockwise to loosen
Rotation
Direction
(E)
Rotate the Rear Leg down and
Tighten the Retaining Knobs
(D)
Loosen the two Rear Leg
Retaining Knobs
Rotate counter-
clockwise to loosen
Retaining
Knob
Rotate Knob
clockwise
to tighten
Rear Leg
(F)
Use proper lifting
techniques when repositioning
the ATS Stand
Reposition
ATS Stand
ATS Stand
Support Plate
Rotation
Direction
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 18
ATS STAND (Document Part Number 158474)
To ensure stability, verify front and rear legs of the ATS Stand are fully extended outward before
installing the saw.
NOTE: When work is complete, place the ATS Stand in the transport position by following steps A through J in
reverse order.
(G)
Verify ATS Stand legs are
fully extended for stability
(H)
Loosen the ATS Stand Support
Plate retaining thumbscrews
as shown
Rotate counter-
clockwise to loosen
(I)
Remove the ATS Stand
Support Plate as shown
ATS Stand
Support Plate
(J)
Install the ATS Stand Support
Plate into the right side of the
ATS Stand as shown
ATS Stand
Support Plate
(K)
Setup the saw for normal
operation in accordance with
the saw Owners Manual
Extend legs
outward
Retaining
Thumbscrew
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 19
ATS STAND (Document Part Number 158474)
MK-2000 Series:
To ensure stability, verify front and rear legs of the ATS Stand are fully extended outward before
installing the saw.
NOTE: The following Brackets are required for fastening the saw to the ATS Stand -
(F)
Verify the rear bracket is
installed correctly
4
D Brackets
(B)
Remove the Cutting Table
(See the saw Owners Manual)
(C)
Verify ATS Stand legs are
fully extended for stability
(A)
Remove Water Pan
(E)
Install the Bracket A and a Bolt
into the top, rear, of the ATS
Stand as shown
(D)
Seat saw on the ATS
Stand as shown
(H)
Install one D Bracket and a Bolt
into the front, side, of the ATS
Stand as shown
(G)
Install one D Bracket and a Bolt
into the rear, side, of the ATS
Stand as shown
Removal
Direction
(I)
Verify the two right-side D
Brackets are installed correctly
Remove
Cutting Table
Extend legs
outward
Back of saw
Back of ATS Stand
Bracket
A
Bracket
D
Install into front hole
on right side of stand
Install into rear hole on
the right side of stand
1
A Bracket
Bracket
A
Fit bracket
over saw frame
Bracket
D
Install into rear hole
on right side of stand
Fit bracket
over saw frame
Bracket
D
ATS Stand (ATS Stand Part No. – 156426) Revision 04/01, Effective Date: April 11, 2001
Page 20
ATS STAND (Document Part Number 158474)
(Q)
Orient and install the ATS
Stand Support Plate as shown
ATS Stand
Support Plate
(P)
Locate the ATS Stand Support
Plate retaining tubes on the back
of the ATS Stand
Retaining
Tubes
Installation
Direction
(O)
Install the Water Pan
(P)
Setup Complete
(K)
Install one D Bracket and a Bolt
into the front, side, of the ATS
Stand as shown
(J)
Install one D Bracket and a Bolt
into the rear, side, of the ATS
Stand as shown
(L)
Verify the two left-side D Brackets
are installed correctly
(N)
Using a 9/16-wrench and socket,
tighten all Bolts
(M)
Install one Nylock nut on the
Bolt of each bracket
(Do not cross-thread the nut)
Nylock
nuts
(Q)
Ensure all bolts are
tight before placing the ATS Stand
in the transport position
Transport
Position
Fit bracket
over saw frame
Bracket
D
Install into rear hole
on left side of stand
Bracket
D
Install into front hole
on left side of stand
Fit bracket
over saw frame
Bracket
D
Rotate clockwise
to install
Rotate
clockwise
to tighten
Rotate
clockwise
to tighten
(R)
Tighten the ATS Stand Support
Plate retaining thumbscrews
as shown
Retaining
Thumbscrew
Page is loading ...
Page is loading ...
/
