Trojan Pulse 260 User manual

CAUTION

READ ALL PRECAUTIONS AND

INSTRUCTIONS IN THIS MANUAL

BEFORE USING THIS EQUIPMENT.

KEEP THIS MANUAL FOR

FUTURE REFERENCE.

2

10305

3

10305

4

10305

5

10305

6

10305

7

10305

No. Description Qty No. Description Qty

1 Screw ST4 x 19 mm 2 34 Mid-handlebar Post 1

2 Round End Cap Ø25 x 16 mm 2 35 Bolt M8 x 45 mm 4

3 Foam Grip Ø23 x 5 mm x 400 mm 2 36 Pedal L/R 2

4 Spring Washer Ø8 mm 4 37 Pulse Wire 1

5 Screw M8 x 30 mm 2 38 Mid-sensor Wire 2 1

6 Spacer Two Hole 1 39 Nylon Nut M10 x 1.25 mm 2

7 Foam Grip Ø30 x 5 mm x 630 mm 2 40 Ball Cap S16 2

8 Ball End Cap Ø32 x Ø50 x 46 mm 2 41 Washer Ø10 x Ø32 x 2 mm 2

9L/R Handlebar L/R 2 42 Short Spacer Ø32 x Ø19.2 x 30 mm 4

10 Square Neck Bolt M8 x 43 mm 4 43 Wave Washer Ø19 x Ø25 x 0.3 mm 4

11 Bushing 2 8 44 End Cap Ø60 x 45.5 mm 2

12 Washer Ø8 x Ø32 x 2 mm 2 45 Main Frame 1

13 Ball Cap S13 6 46 Square End Cap J60 x 30 mm x 15 mm 2

14 Bolt M8 x 16 mm 2 47 Washer Ø6 x Ø12 x 1 mm 2

15 Bushing 1 4 48 Pulse Pad Ø25 mm 2

16L/R Swing Rod Post L/R 2 49 Mid-sensor Wire 1 1

17 Spacer Ø14 x Ø8.3 x 59 mm 2 50 Console 1

18 Washer Ø8 x Ø16 x 1.5 mm 6 51 Tension Wire 1

19 Bolt M8 x 75 mm 2 52 Tension Wire 1

20L/R Pedal Rod Post L/R 2 53 Tension Control 1

21 Nylon Nut M8 6 54 Front Stabiliser 1

22 N/M 55 Rear Stabiliser 1

23 Screw M5 x 10 mm 2 56 Cross Wrench S13-14-15 1

24 Screw M5 x 40 mm 1 57 Wrench S17-19 1

25 Arc Washer Ø5 x Ø20 x R30 x 1.5 mm 1 58 Wrench S13-15 1

26 Upright Post 1 59 Wrench S6 1

27 Arc Washer Ø8 x Ø20 x R16 x 2 mm 4 60L/R Front Chain Cover 1

28 Cap Nut M8 8 61L/R Dial 1

29 Long Spacer Ø32 x Ø19.2 x 75.5 mm 2 62R Brace E Post 1

30 Square Neck Bolt M8 x 73 4 62L Brace E Post 1

31 Curved Washer Ø8 x Ø20 x R30 x 2 mm 8 63 Nylon Nut 4

32 Screw M8 x 16 mm 4 64 Spring Washer 4

33 End Cap Ø60 x Ø78 x 62 mm 2 65 Middle Axis Combine 1

8

10305

No. Description Qty No. Description Qty

66 Belt Pulley 1 98 Bolt M6x Ø12 x 8 mm 1

67 Belt 6PJ340 1 99 Idle Connecting Rod 1

68 Bolt M6 x S10 x 12 mm 3 100 Spring Tension

Ø2.5 x Ø18 x N12 x 64 mm

1

69 Fixed Tray 2 101 Idle Wheel Ø39 x Ø34 x 24 mm 1

70 Bearing 6001-2RS 2 102 Bolt M6 x S1 x 45 mm 1

71 Bearing Block Ø72 x 11 mm 2 103 Nut M6 x H5 x S10 1

72L/R Chain Cover 2 104 Bolt M8 x 12 mm 1

73 Washer Ø17 mm 1

74 Bearing 6203-2RS 2

75 Spacer Ø22 x Ø18 x 6 mm 1

76 Screw M6 x 16 mm 4

77 Bolt ST4.2 x 13 mm 3

78 Alex of Wheel 1

79 Bolt ST4.2 x 13 mm 3

80 Bolt ST4.2 x 19 mm 9

81 Flywheel Ø200 x 2 mm 1

82 Bolt ST4.2 x 16 mm 4

83 Round Magnet Ø15 x 7 mm 2

84 Nut M10 x 1.25 mm 2

85 Crank Cover 2

86 Bolt M6 x S10 x 16 mm 2

87 Spring Washer Ø6 2

88 Washer Ø6 x Ø12 x 1.2 mm 2

89 Axle Washer Ø12 mm 2

90 Alex for Magnet Board

Ø12 x M6 x 61 mm x 8 mm x 45.5 mm

1

91 Magnet Board 1

92 Bolt ST3 x 10 mm 3

93 Spring Tension Ø1.5 x Ø15 x N8 x 41 mm 1

94 Magnet Case 45.5 x 130 x 10.5 mm 1

95 Magnet 40 x 25 x 10 mm 4

96 Washer Ø6 x Ø16 x 1.5 mm 3

97 Bolt M6 x Ø12 x 10 mm 5

9

10305

No. Description Qty No. Description Qty

66 Belt Pulley 1 98 Bolt M6x Ø12 x 8 mm 1

67 Belt 6PJ340 1 99 Idle Connecting Rod 1

68 Bolt M6 x S10 x 12 mm 3 100 Spring Tension

Ø2.5 x Ø18 x N12 x 64 mm

1

69 Fixed Tray 2 101 Idle Wheel Ø39 x Ø34 x 24 mm 1

70 Bearing 6001-2RS 2 102 Bolt M6 x S1 x 45 mm 1

71 Bearing Block Ø72 x 11 mm 2 103 Nut M6 x H5 x S10 1

72L/R Chain Cover 2 104 Bolt M8 x 12 mm 1

73 Washer Ø17 mm 1

74 Bearing 6203-2RS 2

75 Spacer Ø22 x Ø18 x 6 mm 1

76 Screw M6 x 16 mm 4

77 Bolt ST4.2 x 13 mm 3

78 Alex of Wheel 1

79 Bolt ST4.2 x 13 mm 3

80 Bolt ST4.2 x 19 mm 9

81 Flywheel Ø200 x 2 mm 1

82 Bolt ST4.2 x 16 mm 4

83 Round Magnet Ø15 x 7 mm 2

84 Nut M10 x 1.25 mm 2

85 Crank Cover 2

86 Bolt M6 x S10 x 16 mm 2

87 Spring Washer Ø6 2

88 Washer Ø6 x Ø12 x 1.2 mm 2

89 Axle Washer Ø12 mm 2

90 Alex for Magnet Board

Ø12 x M6 x 61 mm x 8 mm x 45.5 mm

1

91 Magnet Board 1

92 Bolt ST3 x 10 mm 3

93 Spring Tension Ø1.5 x Ø15 x N8 x 41 mm 1

94 Magnet Case 45.5 x 130 x 10.5 mm 1

95 Magnet 40 x 25 x 10 mm 4

96 Washer Ø6 x Ø16 x 1.5 mm 3

97 Bolt M6 x Ø12 x 10 mm 5

10

10305

EXPLODED DRAWING

11

10305

12

10305

ASSEMBLY STEPS

2

STEP 2: CONNECTING THE WIRES

• ConnecttheMid-sensorWire1(49)totheMid-sensorWire2(38).

• ConnecttheTensionWire(52)totheTensionWire(51).

• SlidetheUp-rightPost(26)ontotheMainFrame(45)andtightenwithfourScrews(32)andfour

CurvedWashers(31).

CAUTION:

Ensurethatcablesarenotdamaged

duringassemblyorwhen

tighteningscrews.

13

10305

ASSEMBLY STEPS

STEP 3: INSTALLING THE UP-RIGHT POST

• InserttheSwingRodPost(16L/R)ontoeachswingaxisoftheUp-rightPost(26),andtightenwithaBolt

(14),SpringWasher(4)andWasher(12),thencovertheendwithaBallCap(13)onboththeleftand

rightside.

3

CAUTION:

Ensurethatcablesarenotdamaged

duringassemblyorwhen

tighteningscrews.

14

10305

15

10305

5

CAUTION:

Ensurethatcablesarenotdamaged

duringassemblyorwhen

tighteningscrews.

16

10305

17

10305

18

10305

19

10305

PROBLEM SOLUTION

There is no display on the

computer console.

1. Remove the computer console and verify the wire that

comes from the computer console is properly connected

to the wire that comes from the main frame.

2. Check if the batteries are correctly positioned and that

the battery springs are in proper contact with batteries.

3. The batteries in the computer console may be dead.

Change to new batteries.

Squeaking noise when in use. There may be a loose bolt, please inspect the bolts and

tighten if necessary.

20

10305

GROUNDEDOUTLET

GROUNDINGPIN

Page is loading ...

Trojan Pulse 260 User manual

Trojan Pulse 260 User manual

Related papers

Other documents