DT Research DT307SQ Basic Operation Manual
- Type
- Basic Operation Manual
DT307SQ
ENGLISH
Mobile POS Tablet
BASIC OPERATION GUIDE
DT307SQ
ENGLISH
4
signage dtri com
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright © 2016, DT Research, Inc. All Rights Reserved.
BOGW091316DT307SQENG
INTRODUCTION
Thank you for acquiring the DT307SQ Mobile Tablet. The DT307SQ offers a 7
”
capacive
touch display in a compact, rugged, and lightweight package. The DT307SQ enables
efficient point-of-service/sales applicaons, inventory management, and field services.
The DT307SQ provides the precise features needed to streamline operaons and improve
producvity, data accuracy, and service.
PACKAGE CONTENTS
One DT307SQ •
One Baery Pack and Handstrap•
AC-DC Power Adapter•
Basic Operaon Guide•
*The actual package contents may vary depending on the configuraon acquired.
PRECAUTIONS
Always exercise care when operang and handling the DT307SQ.•
Do not disassemble any poron of the DT307SQ, as this will void any product warranty.•
Do not use any power adapter or charging cradle other than the one provided with the •
tablet or acquired from the manufacturer or its partners.
In the unlikely event that abnormal noise, strange odor, or smoke is present, immedi-•
ately power down the DT307SQ and disconnect all power sources. Please report the
problem to your device provider immediately.
MSR/ RFID Reader Module
Enable and disable MSR/ RFID Reader module, and set up the parse data format:
Launch Keyboard Wedge App and click the MSR or RFID tab1.
Turn on the MSR or RFID module2.
Key in Prefix and Suffix codes to adjust the parse data format3.
Click Apply4.
NOTE: Unless you are sure you need to change the parse data format, we recommend
you do not use this seng.
DT307SQ
ENGLISH
2 3
ENGLISH
If your DT307SQ comes with a Barcode Scanner, RFID Reader and/or MSR module(s), you
may refer to the steps below to configure the sengs.
BASIC MODULE OPERATION
3 steps to capture the data results from Keyboard Wedge:
Turn on module from the 1. Keyboard Wedge App
Launch a note-related App2.
Capture the data and verify the results3.
BARCODE SCANNER
Launch the scanner module, and adjust the parse data format :
Tap the 1. Keyboard Wedge App , select SCAN tab, and turn on the Scanner module
Key in Prefix and Suffix codes to adjust the parse data format2.
Click 3. Apply
NOTE: To ensure the system performance, turn on only the symbologies you are
going to use.
DT307SQ I/O Ports
DT307SQ LED Status Indicators
1. Power Mode Status Indicator:
2. Wi-Fi Status Indicator:
Blue: Device is powered on•
Blinking Blue: Main baery charging•
Orange: Low baery mode•
Blinking Orange: Extremely low baery mode•
Off: Device is powered off or in suspend mode•
Blue: Connected to a wireless AP•
Blinking blue: Connecng to a wireless AP•
Off: Wi-Fi is disabled•
A
B
C
D
E
F
Magnec stripe reader (Oponal)
Trigger buon
Camera (Oponal)
LED Flash (Oponal)
Power buon
Baery switch
G
H
I
J
K
L
Micro-SD card reader
Speaker
mini USB port
Headphone-out
USB 2.0 port
DC-in
DT307SQ Front View
DT307SQ Side View
DT307SQ Rear View
A
C D E
F G H
B
I
A
J
K
L
Data Capture Module Operaon Guide
Add/ remove barcode symbologies
Tap 1. Barcode Scanner App
Turn on/off each barcode symbologies under 2. SYMBOLOGY tab
-
1
-
2
DT Research DT307SQ Basic Operation Manual
- Type
- Basic Operation Manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
DT Research DT307SC User manual
-
DT Research DT430 User guide
-
DT Research WebDT 435 User manual
-
-
DT Research DT432SC-MD Basic Operation Manual
-
-
-
DT Research DT315CT Basic Operation Guide
-
DT Research DT410 Specification
-
