Raymarine E90W User Reference Handbook

E-Series Widescreen User reference

Trademark and patents notice

Autohelm, hsb

2

, RayTech Navigator, Sail Pilot, SeaTalk, SeaTalk

NG

, SeaTalk

HS

and Sportpilot are registered trademarks of Raymarine

UK Limited. RayTalk, Seahawk, Smartpilot, Pathnder and Raymarine are registered trademarks of Raymarine Holdings Limited.

FLIR is a registered trademark of FLIR Systems, Inc. and/or its subsidiaries.

All other trademarks, trade names, or company names referenced herein are used for identication only and are the property of

their respective owners.

This product is protected by patents, design patents, patents pending, or design patents pending.

Fair Use Statement

You may print no more than three copies of this manual for your own use. You may not make any further copies or distribute or use the

manual in any other way including without limitation exploiting the manual commercially or giving or selling copies to third parties.

ENGLISH

Document number: 81320-3

Date: 10-2010

Contents

Chapter 1 Important information............................... 9

Safety notices...................................................................9

TFT LCD Displays .......................................................... 10

Water ingress ................................................................. 10

Disclaimers .................................................................... 10

Chart cards and memory cards........................................ 11

EMC conformance .......................................................... 11

Suppression ferrites ........................................................ 11

Connections to other equipment ...................................... 12

Declaration of conformity................................................. 12

Product disposal ............................................................. 12

Warranty registration....................................................... 12

IMO and SOLAS............................................................. 12

Technical accuracy ......................................................... 12

Chapter 2 Handbook information............................ 13

2.1 Handbook information ............................................... 14

2.2 Handbook conventions .............................................. 15

Chapter 3 Getting started ........................................ 17

3.1 Multifunction display system integration ...................... 18

3.2 Networking constraints .............................................. 21

3.3 Display power ........................................................... 22

3.4 Controls.................................................................... 23

3.5 Hybridtouch overview ................................................ 25

3.6 Touchscreen overview ............................................... 26

3.7 Home screen overview ............................................. 26

3.8 Pages ...................................................................... 27

3.9 Applications .............................................................. 29

3.10 Screen overview ..................................................... 30

3.11 Editing information in dialogs.................................... 34

3.12 Basic touchscreen operations .................................. 34

3.13 Databar status symbols ........................................... 35

3.14 Initial setup procedures............................................ 38

Chapter 4 Managing display data ...........................43

4.1 Memory cards overview............................................. 44

4.2 Inserting a memory card, chart card, or CF /

microSD card adaptor ..................................................... 44

4.3 Ensure chart card door is securely closed................... 45

4.4 Removing a memory card, chart card, or CF /

microSD adaptor ............................................................ 45

4.5 Saving user data and user settings............................. 46

4.6 Transferring data using NMEA ................................... 47

4.7 Resetting your system ............................................... 48

Chapter 5 Using waypoints, routes and

tracks.........................................................................49

5.1 Waypoints ................................................................ 50

5

5.2 Routes ..................................................................... 60

5.3 Tracks ...................................................................... 66

5.4 Waypoints, routes and tracks storage capacity ............ 68

Chapter 6 Using the chart........................................69

6.1 Chart application overview ......................................... 70

6.2 Vessel position and orientation................................... 72

6.3 Chart views............................................................... 75

6.4 Chart planning options............................................... 79

6.5 Chart navigation options ............................................ 79

6.6 Measuring distances and bearings ............................. 80

6.7 Chart vectors ............................................................ 81

6.8 Current information ................................................... 82

6.9 Tide information ........................................................ 83

6.10 Chart object information........................................... 85

6.11 Chart layers ............................................................ 86

6.12 Chart presentation................................................... 90

6.13 Chart setup............................................................. 93

Chapter 7 Using autopilot control......................... 103

7.1 Enabling the autopilot control function ...................... 104

7.2 Disengaging the autopilot in an emergency............... 104

7.3 Autopilot control ...................................................... 105

7.4 Autopilot control options .......................................... 106

7.5 Autopilot dialog box ................................................. 106

7.6 Autopilot status symbols .......................................... 107

7.7 Autopilot alarms ...................................................... 108

Chapter 8 Using alarms and MOB

functions ................................................................. 109

8.1 Using Man Overboard (MOB) functions .................... 110

8.2 Alarms.....................................................................111

Chapter 9 Using radar............................................ 117

9.1 Radar overview....................................................... 118

9.2 Digital radar scan speed .......................................... 118

9.3 Radar scanner status symbols ................................. 119

9.4 Radar range and image quality ................................ 120

9.5 Radar display overview ........................................... 123

9.6 Dual range radar operation ...................................... 125

9.7 Radar mode and orientation..................................... 126

9.8 Radar tuning: HD and SuperHD digital

scanners ...................................................................... 129

9.9 Radar tuning: non-HD digital radomes...................... 134

9.10 Using radar to measure distances, ranges, and

bearings....................................................................... 138

9.11 Using radar to track targets and avoid

collisions ...................................................................... 142

9.12 Radar setup menu options ..................................... 146

Chapter 10 Using AIS.............................................149

10.1 AIS overview......................................................... 150

10.2 AIS prerequisites................................................... 151

6 E-Series Widescreen User reference

10.3 Classes of AIS data............................................... 152

10.4 Enabling AIS......................................................... 153

10.5 Displaying AIS vectors........................................... 153

10.6 AIS status symbols................................................ 154

10.7 AIS silent mode..................................................... 154

10.8 Viewing AIS target information ............................... 155

10.9 Using AIS to avoid collisions .................................. 156

10.10 AIS options ......................................................... 157

10.11 AIS alarms .......................................................... 158

10.12 Buddy tracking .................................................... 159

10.13 Aid to Navigation (AToN) targets ........................... 161

10.14 Land base station targets..................................... 162

Chapter 11 Using the Course Deviation

Indicator .................................................................. 165

11.1 Course Deviation Indicator overview ....................... 166

11.2 Displaying the CDI application ................................ 167

11.3 Using the CDI application....................................... 167

Chapter 12 Using the shnder ............................169

12.1 Fishnder introduction ........................................... 170

12.2 The sonar image ................................................... 171

12.3 Fishnder presets.................................................. 173

12.4 Fishnder display modes ....................................... 174

12.5 Fishnder range .................................................... 177

12.6 Fishnder presentation options............................... 178

12.7 Fishnder waypoints.............................................. 183

12.8 Fishnder alarms................................................... 183

12.9 Fishnder setup .................................................... 184

Chapter 13 Using the engine application .............191

13.1 Engine application overview................................... 192

13.2 Displaying the engine application ........................... 192

13.3 Setting up the engine application............................ 193

13.4 Changing the engine panel dial color ...................... 193

13.5 Pre-congured data panels .................................... 194

13.6 Changing what the engine application

displays ....................................................................... 196

Chapter 14 Using the data application ................. 197

14.1 Data application overview ...................................... 198

14.2 Pre-congured data panels .................................... 199

14.3 Trim tab calibration ................................................ 202

14.4 Customizing the data application ............................ 202

Chapter 15 Using the weather application

(North America only).............................................. 205

15.1 Weather application overview................................. 206

15.2 Displaying the weather application.......................... 206

15.3 Weather application setup...................................... 207

15.4 Weather application display overview ..................... 207

15.5 Weather map navigation ........................................ 211

15.6 Weather reports .................................................... 211

7

15.7 Storm tracking....................................................... 212

15.8 Animated weather graphics.................................... 213

Chapter 16 Using Sirius satellite radio (North

America only).......................................................... 215

16.1 Sirius radio overview ............................................. 216

16.2 Displaying the Sirius radio application..................... 216

16.3 Sirius radio basic operations .................................. 217

16.4 Sirius radio presets................................................ 218

16.5 Favorite Sirius radio song alerts ............................. 219

16.6 Sirius radio parental locking ................................... 220

Chapter 17 Using Navtex .......................................221

17.1 Navtex overview.................................................... 222

17.2 Navtex setup......................................................... 222

17.3 Viewing and managing Navtex messages ............... 223

Chapter 18 Using video..........................................225

18.1 Video application overview..................................... 226

18.2 Using video........................................................... 227

Chapter 19 Using the thermal camera

application...............................................................229

19.1 Thermal camera application overview ..................... 230

19.2 Camera control ..................................................... 231

19.3 Image adjustments ................................................ 233

19.4 Camera setup ....................................................... 236

Chapter 20 DSC VHF radio integration.................237

20.1 Using a DSC VHF radio with your display ............... 238

20.2 Enabling DSC VHF radio integration....................... 239

Chapter 21 Customizing your display ..................241

21.1 Customizing the vessel icon................................... 242

21.2 Customizing the databar ........................................ 242

21.3 GPS setup ............................................................ 243

21.4 System setup menu............................................... 245

Chapter 22 Maintaining your display.................... 253

22.1 Service and maintenance ...................................... 254

22.2 Routine equipment checks..................................... 254

22.3 Cleaning ............................................................... 255

22.4 Cleaning the display case ...................................... 255

22.5 Cleaning the display screen ................................... 256

Chapter 23 Technical support ............................... 257

23.1 Raymarine customer support ................................. 258

23.2 3rd party support ................................................... 259

8 E-Series Widescreen User reference

Chapter 1: Important information

Safety notices

Warning: Ensure safe navigation

This product is intended only as an aid to navigation

and must never be used in preference to sound

navigational judgment. Only ofcial government

charts and notices to mariners contain all the current

information needed for safe navigation, and the

captain is responsible for their prudent use. It is the

user’s responsibility to use ofcial government charts,

notices to mariners, caution and proper navigational

skill when operating this or any other Raymarine

product.

Warning: Product installation and

operation

This product must be installed and operated in

accordance with the instructions provided. Failure to

do so could result in personal injury, damage to your

boat and/or poor product performance.

Warning: High voltages

This product contains high voltages. Do NOT remove

any covers or otherwise attempt to access internal

components, unless specically instructed in this

document.

Warning: Touchscreen display

When exposed to prolonged periods of direct sunlight,

the touchscreen display can get very hot. In such

conditions, avoid using the touchscreen display and

use the unit’s physical keys and buttons instead.

Warning: Autopilot control

The autopilot functions available on the multifunction

display do NOT replace the autopilot control head.

You must have a pilot control head installed before

you enable or engage the autopilot.

Warning: Sonar operation

• NEVER operate the sounder with the boat out of

the water.

• NEVER touch the transducer face when the sounder

is powered on.

• SWITCH OFF the sounder if divers are likely to be

within 7.6 m (25 ft) of the transducer.

Warning: Radar scanner safety

Before rotating the radar scanner, ensure all personnel

are clear.

Warning: Radar transmission safety

The radar scanner transmits electromagnetic energy.

Ensure all personnel are clear of the scanner when

the radar is transmitting.

Important information

9

Caution: Care of chart cards

To avoid irreparable damage to and/or loss of data

from chart cards:

• Ensure that chart cards are tted the correct way

around. DO NOT try to force a card into position.

• DO NOT save data (waypoints, routes, and so on)

to a chart card, as the charts may be overwritten.

• DO NOT use a metallic instrument such as a

screwdriver or pliers to remove a chart card.

• Safe removal. Use the Remove Card menu option

before removing the chart card.

Caution: Ensure chart card door is

securely closed

To prevent water ingress and consequent damage to

the display, ensure that the chart card door is rmly

closed. This can be conrmed by an audible click.

Caution: Cleaning

When cleaning this product:

• Do NOT wipe the display screen with a dry cloth, as

this could scratch the screen coating.

• Do NOT use abrasive, or acid or ammonia based

products.

• Do NOT use a jet wash.

TFT LCD Displays

The colors of the display may seem to vary when viewed against

a colored background or in colored light. This is a perfectly normal

effect that can be seen with all color Liquid Crystal Displays (LCDs).

In common with all Thin Film Transistor (TFT) LCD units, the screen

may exhibit a few (less than 7) wrongly illuminated pixels. These

may appear as black pixels in a light area of the screen or as colored

pixels in black areas.

Water ingress

Water ingress disclaimer

Although the waterproof rating capacity of Raymarine products

exceeds that called for by the IPX6 standard, water intrusion

and subsequent equipment failure may occur if any Raymarine

equipment is subjected to commercial high pressure washing.

Raymarine will not warrant equipment subjected to high pressure

washing.

Disclaimers

This product (including the electronic charts) is intended to be used

only as an aid to navigation. It is designed to facilitate use of ofcial

government charts, not replace them. Only ofcial government

charts and notices to mariners contain all the current information

needed for safe navigation, and the captain is responsible for their

prudent use. It is the user’s responsibility to use ofcial government

charts, notices to mariners, caution and proper navigational skill

when operating this or any other Raymarine product. This product

supports electronic charts provided by third party data suppliers

which may be embedded or stored on memory card. Use of such

10 E-Series Widescreen User reference

charts is subject to the supplier’s End-User Licence Agreement

included in the documentation for this product or supplied with the

memory card (as applicable).

Raymarine does not warrant that this product is error-free or that it

is compatible with products manufactured by any person or entity

other than Raymarine.

This product uses digital chart data, and electronic information from

the Global Positioning System (GPS) which may contain errors.

Raymarine does not warrant the accuracy of such information and

you are advised that errors in such information may cause the

product to malfunction. Raymarine is not responsible for damages

or injuries caused by your use or inability to use the product, by the

interaction of the product with products manufactured by others, or

by errors in chart data or information utilized by the product and

supplied by third parties.

Chart cards and memory cards

Compatible cards

The following types of memory or chart card are compatible with

your Raymarine system:

• CompactFlash (CF)

• micro Secure Digital (microSD)

• micro Secure Digital High-Capacity (microSDHC)

Note: microSD and microSDHC cards require the optional

Raymarine CF / microSD card adaptor. Only the ofcial

Raymarine adaptor is compatible with your system.

Chart cards

Your system is pre-loaded with electronic charts for your region. If

you wish to use different chart data, you can insert compatible CF

chart cards into the CompactFlash card slot on your unit. If you

want to use microSD or microSDHC chart cards, you must purchase

the optional CF / microSD card adaptor and insert it into the

CompactFlash card slot on your unit. The microSD or microSDHC

chart card must be inserted into the adaptor.

Use branded chart cards and memory cards

When archiving data, Raymarine recommends the use of quality

branded memory cards. Some brands of memory card may not

work in your unit. Please contact customer support for a list of

recommended cards.

EMC conformance

Raymarine equipment and accessories conform to the appropriate

Electromagnetic Compatibility (EMC) regulations for use in the

recreational marine environment.

Correct installation is required to ensure that EMC performance is

not compromised.

Suppression ferrites

Raymarine cables may be tted with suppression ferrites. These

are important for correct EMC performance. If a ferrite has to be

removed for any purpose (e.g. installation or maintenance), it must

be replaced in the original position before the product is used.

Use only ferrites of the correct type, supplied by Raymarine

authorized dealers.

Important information

11

Connections to other equipment

Requirement for ferrites on non-Raymarine cables

If your Raymarine equipment is to be connected to other equipment

using a cable not supplied by Raymarine, a suppression ferrite

MUST always be attached to the cable near the Raymarine unit.

Declaration of conformity

Raymarine Ltd. declares that G-Series systems are in compliance

with the essential requirements of EMC directive 2004/108/EC.

The original Declaration of Conformity certicate may be viewed on

the relevant product page at

www.raymarine.com

Product disposal

Dispose of this product in accordance with the WEEE Directive.

The Waste Electrical and Electronic Equipment (WEEE)

Directive requires the recycling of waste electrical and electronic

equipment. Whilst the WEEE Directive does not apply to some

Raymarine products, we support its policy and ask you to be aware

of how to dispose of this product.

Warranty registration

To register your Raymarine product ownership, please take a few

minutes to ll out the warranty registration card found in the box, or

visit

www.raymarine.com and register on-line.

It is important that you register your product to receive full warranty

benets. Your unit package includes a bar code label indicating the

serial number of the unit. You should stick this label to the warranty

registration card.

IMO and SOLAS

The equipment described within this document is intended for use

on leisure marine boats and workboats not covered by International

Maritime Organization (IMO) and Safety of Life at Sea (SOLAS)

Carriage Regulations.

Technical accuracy

To the best of our knowledge, the information in this document was

correct at the time it was produced. However, Raymarine cannot

accept liability for any inaccuracies or omissions it may contain. In

addition, our policy of continuous product improvement may change

specications without notice. As a result, Raymarine cannot accept

liability for any differences between the product and this document.

12

E-Series Widescreen User reference

Chapter 2: Handbook information

Chapter contents

• 2.1 Handbook information on page 14

• 2.2 Handbook conventions on page 15

Handbook information 13

2.1 Handbook information

This handbook contains important information regarding the

E-Series Widescreen range of multifunction displays.

The handbook is for use with the following models:

• E90W Widescreen Multifunction Display

• E120W Widescreen Multifunction Display

• E140W Widescreen Multifunction Display

About this handbook

This handbook describes how to operate your multifunction display

in conjunction with compatible electronic cartography and peripheral

equipment.

It assumes that all peripheral equipment to be operated with it

is compatible and has been correctly installed. This handbook

is intended for users of varying marine abilities, but assumes a

general level of knowledge of display use, nautical terminology

and practices.

E-Series handbooks

The E-Series Widescreen Multifunction Display has the following

handbooks available:

All documents are available to download as PDFs from

www.raymarine.com

E-Series handbooks

Description Part number

Installation and commissioning

instructions

87116

Operating instructions (quick

reference)

86137

User reference handbook

81320

Additional handbooks

Description Part number

SeaTalk

ng

reference manual

81300

14

E-Series Widescreen User reference

2.2 Handbook conventions

Conventions used in this handbook.

The following conventions are used throughout this handbook when

referring to:

• Softkeys — the term "select" is used in procedures involving

softkeys to refer to the action of selecting a softkey, either using

touch or by pressing the corresponding physical key.

• Menus — the term "select" is used in procedures involving menus

to refer to the action of selecting an item, either by touch or with

physical keys and buttons.

Handbook information 15

16 E-Series Widescreen User reference

Chapter 3: Getting started

Chapter contents

• 3.1 Multifunction display system integration on page 18

• 3.2 Networking constraints on page 21

• 3.3 Display power on page 22

• 3.4 Controls on page 23

• 3.5 Hybridtouch overview on page 25

• 3.6 Touchscreen overview on page 26

• 3.7 Home screen overview on page 26

• 3.8 Pages on page 27

• 3.9 Applications on page 29

• 3.10 Screen overview on page 30

• 3.11 Editing information in dialogs on page 34

• 3.12 Basic touchscreen operations on page 34

• 3.13 Databar status symbols on page 35

• 3.14 Initial setup procedures on page 38

Getting started

17

3.1 Multifunction display system

integration

You can connect a number of external devices to your multifunction

display, providing additional features and functions.

The following diagram illustrates the various external devices that

can be connected to your multifunction display:

Your multifunction display uses a number of protocols to transfer

data between the various devices in your networked system. The

following table details which devices may be connected to your

display, and the type of connectivity (in terms of protocols and

physical interfaces):

18 E-Series Widescreen User reference

Device Type Suitable Devices Connectivity

Radar Up to two Raymarine

radar scanners may

be connected to your

multifunction display,

but only one may be

operated at any one

time.

• 4 kilowatt Digital

Radome Scanner.

• 4 kilowatt HD Digital

Radome Scanner.

• 4 kilowatt HD Digital

Open Array Scanner.

• 12 kilowatt HD Digital

Open Array Scanner.

• 4 kilowatt SuperHD

Digital Open Array

Scanner.

• 12 kilowatt SuperHD

Digital Open Array

Scanner.

Note: Please

ensure your radar

scanner is using

the latest software

version.

SeaTalk

hs

Fishnder The E-Series

Widescreen display

supports the connection

SeaTalk

hs

Device Type Suitable Devices Connectivity

of ONE of the following

Raymarine shnders:

• DSM 30

• DSM 300

• DSM 400

Cartography — included Embedded (internal)

Navionics cartography

Internal storage

Cartography — optional External CompactFlash,

microSD, or microSDHC

chart cards:

• Navionics Silver

• Navionics Gold

• Navionics Gold+

• Navionics Platinum

• Navionics Platinum+

• Navionics Fish’N Chip

• Navionics Hotmaps

Refer to the

Raymarine website

(

www.raymarine.com)

for the latest list of

supported chart cards.

Card slot

Note: microSD

and microSDHC

cards require the

optional Raymarine

CF / microSD card

adaptor. Only the

ofcial Raymarine

adaptor is compatible

with your system.

Sirius Weather/Audio • Raymarine SR100

Sirius Weather

Receiver

SeaTalk

hs

Getting started

19

Device Type Suitable Devices Connectivity

AIS The E-Series

Widescreen display

supports the connection

of ONE of the following

AIS units:

• Raymarine AIS 250

• Raymarine AIS 500

• Third-party AIS Class

A or Class B receiver

/ transceiver

NMEA 0183 or

SeaTalk

ng

Navtex Navtex Receiver NMEA 0183

Fast Heading Sensor Fast Heading Sensor

NMEA 0183

GPS — external Raystar125 GPS or

third-party external GPS

receiver

SeaTalk, SeaTalk

ng

, or

NMEA 0183

Instruments All current Raymarine

instruments

SeaTalk, SeaTalk

ng

, or

NMEA 0183

Autopilot — Raymarine All current Raymarine

autopilots

SeaTalk, SeaTalk

ng

Autopilot — third party Third-party autopilots

NMEA 0183 (waypoint

and bearing information)

VHF radio

Raymarine DSC VHF

radios

NMEA 0183, SeaTalk

Additional multifunction

display(s)

E90W, E120W, E140W,

G-Series displays.

SeaTalk, SeaTalk

hs

,

SeaTalk

ng

Device Type Suitable Devices Connectivity

Thermal camera

The E-Series

Widescreen display

supports the connection

of ONE of the following

Raymarine thermal

cameras:

• T300 thermal camera

(9 Hz)

• T303 thermal camera

(30 Hz)

• T350 thermal camera

(9 Hz)

• T400 thermal camera

(9 Hz)

• T403 thermal camera

(30 Hz)

• T450 thermal camera

(9 Hz)

SeaTalk

hs

(for control),

BNC connector (for

video)

Video / camera Composite or S-Video

PAL or NTSC video

source

BNC connector

20 E-Series Widescreen User reference

Page is loading ...

Raymarine E90W, E-Series, E120W, E140W User Reference Handbook

Related papers

Other documents