Supermicro MNL-H8DI3+-F User manual

Brand: Supermicro

Model: MNL-H8DI3+-F

Category: Server/workstation motherboards

Type: User manual

SUPER

H8DI3+-F

H8DI3+

H8DII+-F

H8DII+

USER’S MANUAL

Revision 1.0c

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates. Please Note: For the most up-to-date version of this

manual, please see our web site at www.supermicro.com.

Super Micro Computer, Inc. ("Supermicro") reserves the right to make changes to the product

described in this manual at any time and without notice. This product, including software and

documentation, is the property of Supermicro and/or its licensors, and is supplied only under a

license. Any use or reproduction of this product is not allowed, except as expressly permitted by

the terms of said license.

IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL,

SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE

COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH

HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. Super Micro's total liability for all

claims will not exceed the price paid for the hardware product.

FCC Statement: This equipment has been tested and found to comply with the limits for a Class

A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the manufacturer’s instruction manual, may cause harmful

interference with radio communications. Operation of this equipment in a residential area is likely

to cause harmful interference, in which case you will be required to correct the interference at your

own expense.

California Best Management Practices Regulations for Perchlorate Materials: This Perchlorate

warning applies only to products containing CR (Manganese Dioxide) Lithium coin cells. “Perchlorate

Material-special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate”

WARNING: Handling of lead solder materials used in this

product may expose you to lead, a chemical known to

the State of California to cause birth defects and other

reproductive harm.

Manual Revision 1.0c

Release Date: April 15, 2010

Unless you request and receive written permission from SUPER MICRO COMPUTER, you may not

copy any part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

Preface

iii

Preface

About This Manual

This manual is written for system integrators, PC technicians and

knowledgeable PC users. It provides information for the installation and use of the

H8DI3+/I+(-F) Serverboard. The H8DI3+/I+(-F) serverboard is based on the AMD®

SR5690/SP5100 chipset and supports dual AMD Socket F type processors with up

to 128 GB of DDR2-800/667/533 registered ECC SDRAM. This series includes the

following serverboards and characteristics:

H8DI3+-F H8DI3+ H8DII+-F H8DII+

Embeded IPMI Yes Yes

Onbard SAS Yes Yes

PCI-X Yes Yes Yes Yes

Please refer to the mainboard speciﬁ cations pages on our web site for updates on

supported processors (http://www.supermicro.com/aplus/). This product is intended

to be professionally installed.

Manual Organization

Chapter 1 includes a checklist of what should be included in your serverboard

box, describes the features, speciﬁ cations and performance of the serverboard and

provides detailed information about the chipset.

Chapter 2 begins with instructions on handling static-sensitive devices. Read this

chapter when installing the processor(s) and memory modules and when installing

the serverboard in a chassis. Also refer to this chapter to connect the hard disk

drives, the various ports, and the power and reset buttons and the system LEDs.

If you encounter any problems, see Chapter 3, which describes troubleshooting

procedures for the video, the memory and the setup conﬁ guration stored in CMOS.

For quick reference, a general FAQ (Frequently Asked Questions) section is

provided. Instructions are also included for contacting technical support. In addition,

you can visit our web site for more detailed information.

Chapter 4 includes an introduction to BIOS and provides detailed information on

running the CMOS Setup utility.

Appendix A provides BIOS Error Beep Code Messages.

Appendix B lists BIOS POST Checkpoint Codes.

H8DI3+/I+(-F) Serverboard User’s Manual

Table of Contents

Chapter 1 Introduction

1-1 Overview ............................................................................................................ 1

Checklist ............................................................................................................. 1

1-2 Contacting Supermicro ....................................................................................... 2

1-3 Chipset Overview ............................................................................................. 10

AMD SR5690/SP5100 Processor .................................................................... 10

HyperTransport Technology ............................................................................. 10

1-4 PC Health Monitoring ....................................................................................... 10

1-5 Power Conﬁ guration Settings............................................................................11

1-6 Power Supply ................................................................................................... 12

1-7 Super I/O .......................................................................................................... 13

Chapter 2 Installation

2-1 Static-Sensitive Devices ..................................................................................... 1

Precautions ........................................................................................................ 1

Unpacking .......................................................................................................... 1

2-2 Processor and Heatsink Installation................................................................... 2

2-3 Mounting the Serverboard into a Chassis ......................................................... 4

2-4 Installing Memory ............................................................................................... 4

Support ............................................................................................................... 5

Maximum Memory .............................................................................................. 5

2-5 PCI Expansion Cards ......................................................................................... 6

2-6 I/O Port and Control Panel Connections ........................................................... 7

Front Control Panel ............................................................................................ 7

2-7 Connector Deﬁ nitions ........................................................................................ 8

Power Connectors ........................................................................................ 8

PW_ON Connector ........................................................................................ 8

Reset Connector ........................................................................................... 8

Overheat/Fan Fail LED (OH)......................................................................... 8

NIC2 (LAN2) LED .......................................................................................... 9

NIC1 (LAN1) LED .......................................................................................... 9

HDD LED ....................................................................................................... 9

Power On LED .............................................................................................. 9

NMI Button .................................................................................................... 9

LAN1/2 (Ethernet Ports) ................................................................................ 9

Universal Serial Bus Ports .......................................................................... 10

USB Headers .............................................................................................. 10

Fan Headers ................................................................................................ 10

Table of Contents

Serial Ports .................................................................................................. 10

SGPIO ..........................................................................................................11

SMBus Header .............................................................................................11

Wake-On-LAN ..............................................................................................11

Power I2C .....................................................................................................11

Overheat LED ...............................................................................................11

Chassis Intrusion ........................................................................................ 12

Power LED/Speaker .................................................................................... 12

ATX PS/2 Keyboard and PS/2 Mouse Ports ............................................... 12

I-Button ........................................................................................................ 12

Compact Flash Card PWR Connector ........................................................ 13

2-8 Jumper Settings ............................................................................................... 13

Explanation of Jumpers ................................................................................... 13

CMOS Clear ................................................................................................ 13

I2C to PCI-Express Slot .............................................................................. 14

Watch Dog Enable/Disable ......................................................................... 14

PCI-X Slot Frequency Selection.................................................................. 14

VGA Enable/Disable .................................................................................... 14

LAN1/2 Enable/Disable .............................................................................. 15

Compact Flash Master/Slave Select ........................................................... 15

SAS Enable/Disable .................................................................................... 15

SAS RAID Mode Select .............................................................................. 15

JPS2 allows you to select the SAS RAID mode, either Software RAID or IT

Mode. Close this jumper to use Software RAID (the default setting). Set this

jumper to open to use the IT Mode. ................................................................ 15

2-9 Onboard Indicators ........................................................................................... 16

LAN1/LAN2 LEDs ........................................................................................ 16

Dedicated IPMI LAN LEDs .......................................................................... 16

Power LED .................................................................................................. 16

IPMI LED ..................................................................................................... 16

2-10 Floppy, SAS and SATA Drive Connections ...................................................... 17

IDE Connectors ........................................................................................... 17

Floppy Drive Connector .............................................................................. 18

SATA Ports .................................................................................................. 18

SAS Ports .................................................................................................... 18

2-11 Enabling SATA RAID ........................................................................................ 19

Serial ATA (SATA)............................................................................................. 19

Installing the OS/SATA Driver .......................................................................... 19

Building a Driver Diskette ............................................................................ 19

H8DI3+/I+(-F) Serverboard User’s Manual

vii

Enabling SATA RAID in the BIOS ............................................................... 20

Using the Adaptec RAID Utility ........................................................................ 21

Installing the RAID Driver During OS Installation ............................................ 21

2-12 Installing Drivers ............................................................................................... 22

Supero Doctor III .............................................................................................. 23

Chapter 3 Troubleshooting

3-1 Troubleshooting Procedures .............................................................................. 1

Before Power On ............................................................................................... 1

No Power ........................................................................................................... 1

No Video ............................................................................................................ 2

Memory Errors .................................................................................................. 2

Losing the System’s Setup Conﬁ guration .......................................................... 2

3-2 Technical Support Procedures ........................................................................... 3

3-3 Frequently Asked Questions .............................................................................. 3

3-4 Returning Merchandise for Service.................................................................... 4

Chapter 4 BIOS

4-1 Introduction ......................................................................................................... 1

4-2 Main Menu ......................................................................................................... 2

4-3 Advanced Settings Menu ................................................................................... 2

4-4 Security Menu .................................................................................................. 19

4-5 Boot Menu ........................................................................................................ 19

4-6 Exit Menu ......................................................................................................... 20

Appendix A BIOS Error Beep Codes

Appendix B BIOS POST Checkpoint Codes

B-1 Uncompressed Initialization Codes .................................................................... 1

B-2 Bootblock Recovery Codes ................................................................................ 2

B-3 Uncompressed Initialization Codes .................................................................... 3

viii

Notes

Preface

Chapter 1: Introduction

1-1

Chapter 1

Introduction

1-1 Overview

Checklist

Congratulations on purchasing your computer serverboard from an acknowledged

leader in the industry. Supermicro boards are designed with the utmost attention to

detail to provide you with the highest standards in quality and performance.

Please check that the following items have all been included with your serverboard.

If anything listed here is damaged or missing, contact your retailer.

IDE cable (CBL-036L-03)

•

Floppy cable (CBL-022L)•

COM port cable (CBL-010L)•

SATA cable x 4 (CBL-044L)•

SAS cable x2 (CBL-0097L-02) (see note below)•

IO shield (MCP-260-00027-0N)•

CD-ROM drivers and software (CDR-APLUS2 v 1.00 or newer)•

Note: The SAS cable is not provided for the H8DII+-F or H8DII+ serverboards.

1-2

H8DI3+/I+(-F) Serverboard User’s Manual

1-2 Contacting Supermicro

Headquarters

Address: Super Micro Computer, Inc.

980 Rock Ave.

San Jose, CA 95131 U.S.A.

Tel: +1 (408) 503-8000

Fax: +1 (408) 503-8008

Email: [email protected] (General Information)

[email protected] (Technical Support)

Web Site: www.supermicro.com

Europe

Address: Super Micro Computer B.V.

Het Sterrenbeeld 28, 5215 ML

's-Hertogenbosch, The Netherlands

Tel: +31 (0) 73-6400390

Fax: +31 (0) 73-6416525

Email: [email protected] (General Information)

[email protected] (Technical Support)

[email protected] (Customer Support)

Asia-Paciﬁ c

Address: Super Micro Computer, Inc.

4F, No. 232-1, Liancheng Rd.

Chung-Ho 235, Taipei County

Taiwan, R.O.C.

Tel: +886-(2) 8226-3990

Fax: +886-(2) 8226-3991

Web Site: www.supermicro.com.tw

Technical Support:

Email: [email protected]

Tel: 886-2-8228-1366, ext.132 or 139

Chapter 1: Introduction

1-3

Figure 1-1. H8DI3+/I+(-F) Serverboard Image

1-4

H8DI3+/I+(-F) Serverboard User’s Manual

Notes:

Jumpers not indicated are for test purposes only.

Not all ports, jumpers or LED Indicators are available on all serverboards.

Figure 1-2. H8DI3+/I+(-F) Serverboard Serverboard Layout

(not drawn to scale)

JPI2C

JPW3JPW2

JPW1

JF1

JWF1

JWOL

JPL2

JPT1

JPS1

JPX1B

JPX1A

JPL1

JPB

JPG1

JWD

JPUSB1

JD1

BATTERY

SATA0 SATA2 SATA4

SATA1 SATA3 SATA5

JLPC80

FAN4

FAN3

FAN7

FAN1FAN2

FAN5

FAN8

FAN6

JL1

JOH1

JPS2

JCF1

JI2C2

JI2C1

USB6/7USB2/3

KB &

MOUSE

USB 0/1 &

IPMI LAN

COM1

VGA

LAN1

LAN2

COM2

USB4 USB5

I-BUTTON

SAS 4~7

T-SGPIO1

SAS 0~3

SMBus1

SLOT6 PCI-E 2.0 x8

SLOT5 PCI-E 2.0 x8

SLOT4 PCI-E 2.0 x8

CPU1/DIMM1B

CPU1/DIMM1A

CPU1/DIMM2B

CPU1/DIMM2A

CPU1/DIMM3B

CPU1/DIMM4B

CPU2/DIMM4A

CPU2/DIMM4B

CPU2/DIMM3A

CPU2/DIMM3B

CPU2/DIMM2A

CPU2/DIMM2B

CPU2/DIMM1A

SLOT3 PCI-E 2.0 x4

FLOPPY

JBT1:

CMOS

CLEAR

SLOT1 PCI-X 133MHz

CPU1/DIMM4A

CPU1

CPU2

CPU2/DIMM1B

SLOT2 PCI-X 133MHz

IDE#1

CPU1/DIMM3A

AMD

SR5690

NEC

uPD720400

SAS

LSI1068E

AMD

SP5100

BMC

DP5

DP4

Chapter 1: Introduction

1-5

H8DI3+/I+(-F) Serverboard Quick Reference

Jumper Description Default Setting

JBT1 CMOS Clear (See Section 2-7)

JCF1 Compact Flash Master/Slave Closed (Master)

C1/JI

C2 I

C to PCI-E Slot Enable/Disable Both Closed (Enabled)

JPG1 VGA Enable/Disable Pins 1-2 (Enabled)

JPL1/JPL2 LAN 1/2 Enable/Disable Pins 1-2 (Enabled)

JPS1 SAS Controller Enable/Disable Pins 1-2 (Enabled)

JPS2 SAS RAID Mode On (Software RAID)

JPX1A/JPX1B PCI-X Slot Frequency Selection Open (Auto)

JWD Watch Dog Pins 1-2 (Reset)

LED Description

LAN Ports LEDs for the LAN Ethernet ports

Dedicated IPMI LAN LEDs for the dedicated IPMI LAN Ethernet port

Power LED (DP4) LED showing power connected for serverboard

IPMI LED (DP5) LED showing IPMI connection

1-6

H8DI3+/I+(-F) Serverboard User’s Manual

Connector Description

COM1/COM2 COM1 Serial Port/Header

FAN 1-8 Chassis/CPU Fan Headers

Floppy Floppy Disk Drive Connector

I-Button I-Button Socket (for RAID 5 support)

IDE#1 IDE Disk Drive Connector

IPMI LAN Dedicated IPMI LAN Port

JD1 Speaker Header

JF1 Front Panel Connector

JL1 Chassis Intrusion Header

JOH1 Overheat Warning Header

JPI2C Power I

C Header

JPW1 24-pin Main ATX Power Connector

JPW2/3 +12V 8-pin CPU Power Connectors

JWF1 Compact Flash Card Power Connector

JWOL Wake-On-LAN Header

LAN1/2 Gigabit Ethernet (RJ45) Ports

PS2 Mouse/Keyboard PS2 Mouse/Keyboard connectors

SMBus System Management Bus Header

SAS0~3, SAS4~7 SAS Ports

SATA0 ~ SATA5 SATA Ports

T-SGPIO-1 Serial General Purpose Input/Output Header

USB0/1, USB4/5, USB2/3 Universal Serial Bus (USB) Ports, Headers

VGA VGA Connector

Chapter 1: Introduction

1-7

Serverboard Features

CPU

Dual AMD Opteron 2000 series (Socket F type) processors•

Note: Supports 237x, 238x, 235x and 24xx processors. Please refer to our web site for further

details on supported processors.

Memory

Sixteen single/dual channel DIMM slots supporting up to 128 GB of DDR2-800•

/667/533 registered ECC SDRAM

Note: Due to a CPU limitation, fully populating DIMM slots with DDR2-667 will pull the speed down to

533 MHz (see our web site for possible updates to this). Refer to Section 2-4 before installing memory

and our web site for recommended DIMMs.

Chipset

AMD SR5690/SP5100 chipset/southbridge•

Expansion Slots

Two (2) PCI-Express x16 (x8 signal) slots (Slot 4 and 6)•

One (1) PCI-Express x8 slot (Slot 5)•

One (1) PCI-Express x8 (x4 signal) slot (Slot 3)•

Two (2) PCI-X 133 slots (Slot 1: Channel B, Slot 2: Channel A)•

BIOS

16 Mb AMIBIOS•

SPI Flash ROM

APM 1.2, DMI 2.3, PCI 2.2, ACPI 1.0 (ACPI 2.0 is BIOS supported), SMBIOS

•

2.3, Plug and Play (PnP)

PC Health Monitoring

Onboard voltage monitors•

Fan status monitor with ﬁ rmware/software on/off and speed control•

Watch Dog•

Environmental temperature monitoring via BIOS•

Power-up mode control for recovery from AC power loss•

System resource alert (via included utility program)•

Auto-switching voltage regulator for the CPU core•

CPU thermal trip support•

I•

C temperature sensing logic

1-8

H8DI3+/I+(-F) Serverboard User’s Manual

ACPI Features

Microsoft OnNow•

Slow blinking LED for suspend state indicator•

BIOS support for USB keyboard•

Wake-On-LAN (WOL) and Wake-On-Ring (WOR) headers•

Internal/external modem ring-on•

Onboard I/O

On-chip SATA controller supporting six (6) SATA ports (RAID 0, 1, 10 sup-•

ported)

LSI 1068E SAS controller (H8DI3+(-F) only, RAID 0, 1, 10 and JBOD; optional

•

RAID 5 support with I-Button installed).

Two (2) Fast UART 16550 compatible serial port (one header and one port)

•

Two on-board PCIE link INTEL 82574L Gigabit ethernet chipset supports two •

Gigabit LAN ports

Six (6) USB (Universal Serial Bus 2.0) ports (2x rear, 2x header, 2x type A)

•

One (1) dedicated IPMI LAN port•

Onboard Matrox•

G200 graphics controller (with 16 MB DDR2 memory) sup-

ports one (1) VGA port

Other

Onboard power LED•

Chassis intrusion detection•

CD Utilities

BIOS ﬂ ash upgrade utility•

Super Doctor III•

IPMI 1.5 / 2.0 (Optional)•

Dimensions

Extended ATX form: 12" x 13" (310 x 330 mm)•

Chapter 1: Introduction

1-9

Figure 1-3. AMD SR5690/SP5100 Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your serverboard. See the previous pages for the

actual speciﬁ cations of your serverboard.

DDR2

DDR2 533/667/800

Socket F

AMD

H0L1

HT Link

16/16-1GHz

H0L2

16/16-1GHz

HT Link

SR5690

COM1

DIMM B2

DIMM B4

AMD

Socket F

CPU2

H0L0

HT Link

16/16-1GHz

W83795G

DIMM B6

DIMM B8

DIMM A5

DIMM B6

DIMM A7 DIMM B8

DIMM A3

DIMM A1 DIMM B2

DIMM B4

DIMM A5

DIMM A7

DIMM A3

DIMM A1

DDR2 533/667/800

PCI-E GEN2 X8

Slot6

PCI-E GEN2 X8

SAS Controller

LSI 1068E

IDE (ATA/133)

SATA x6

PCI-E GEN2 X4

Slot3

PCI-E GEN2 X8

Slot4

PCI-E GEN2 X8

Slot5

PCI-X 64Bit

133/100 MHz Slot

NEC

PD720400

PCI-E GEN2 X4

PCI-X A

PCI-X B

PCI-E GEN2 X1

Intel 82574L

GbE(LAN2)

SAS x4

PCI-X 64Bit

133/100 MHz Slot

RJ45

SP5100

BMC

VGA

WPCM450-R

PCI

2x USB

LPC

SMBus

W83627DHG

SIOHWM

SPI Flash

KB/MS

COM2

FLOPPY

RMII

DDR2 SDRAM

64MB X16

PSU I2C

IPMB

FE PHY

RTL8201N

VGA

RJ45

2XUSB

4XUSB

Intel 82574L

GbE(LAN1)

PCI-E GEN2 X1

RJ45

1-10

H8DI3+/I+(-F) Serverboard User’s Manual

1-3 Chipset Overview

The H8DI3+/I+(-F) Serverboard serverboard is based on the AMD SR5690/SP5100

chipset. This chipset functions as a Media and Communications Processor (MCP).

Controllers for the system memory are integrated directly into AMD Opteron

processors.

AMD SR5690/SP5100 Processor

The AMD SR5690 and SP5100 are each single-chip, high-performance

HyperTransport peripheral controllers for northbridge and southbridge functions,

respectively. They both include a 46-lane PCI Express interface, an AMD Opteron

16-bit Hyper Transport interface link, a six-port Serial ATA interface, a dual-port Gb

Ethernet interface and a six-port USB 2.0 interface. The AMD SR5690 connects

directly to the CPUs.

HyperTransport Technology

HyperTransport technology is a high-speed, low latency point to point link that was

designed to increase the communication speed by a factor of up to 48x between

integrated circuits. This is done partly by reducing the number of buses in the

chipset to reduce bottlenecks and by enabling a more efﬁ cient use of memory

in multi-processor systems. The end result is a signiﬁ cant increase in bandwidth

within the chipset.

1-4 PC Health Monitoring

This section describes the PC health monitoring features of the H8DI3+/I+(-F)

Serverboard. The serverboard has an onboard System Hardware Monitor chip that

supports PC health monitoring.

Onboard Voltage Monitors

The onboard voltage monitor will continuously scan crucial voltage levels. Once

a voltage becomes unstable, it will give a warning or send an error message to

the screen. Users can adjust the voltage thresholds to deﬁ ne the sensitivity of the

voltage monitor. Real time readings of these voltage levels are all displayed in

BIOS.

Fan Status Monitor with Firmware/Software Speed Control

The PC health monitor can check the RPM status of the cooling fans. The onboard

fans are controlled by thermal management via BIOS.

Chapter 1: Introduction

1-11

CPU Overheat/Fan Fail LED and Control

This feature is available when the user enables the CPU overheat/Fan Fail warning

function in the BIOS. This allows the user to deﬁ ne an overheat temperature. When

this temperature is exceeded or when a fan failure occurs, the Overheat/Fan Fail

warning LED is triggered.

Auto-Switching Voltage Regulator for the CPU Core

The 3-phase-switching voltage regulator for the CPU core can support up to 80A

and auto-sense voltage IDs ranging from 0.8 V to 1.55V. This will allow the regulator

to run cooler and thus make the system more stable.

1-5 Power Conﬁ guration Settings

This section describes the features of your serverboard that deal with power and

power settings.

Microsoft OnNow

The OnNow design initiative is a comprehensive, system-wide approach to system

and device power control. OnNow is a term for a PC that is always on but appears

to be off and responds immediately to user or other requests.

Slow Blinking LED for Suspend-State Indicator

When the CPU goes into a suspend state, the chassis power LED will start blinking

to indicate that the CPU is in suspend mode. When the user presses any key, the

CPU will wake-up and the LED will automatically stop blinking and remain on.

BIOS Support for USB Keyboard

If a USB keyboard is the only keyboard in the system, it will function like a normal

keyboard during system boot-up.

Main Switch Override Mechanism

The power button can function as a system suspend button. When the user

depresses the power button, the system will enter a SoftOff state. The monitor

will be suspended and the hard drive will spin down. Depressing the power button

again will cause the whole system to wake-up. During the SoftOff state, the power

supply provides power to keep the required circuitry in the system alive. In case the

system malfunctions and you want to turn off the power, just depress and hold the

power button for 4 seconds. The power will turn off and no power will be provided

to the serverboard.

1-12

H8DI3+/I+(-F) Serverboard User’s Manual

Wake-On-LAN (WOL)

Wake-On-LAN is deﬁ ned as the ability of a management application to remotely

power up a computer that is powered off. Remote PC setup, up-dates and access

tracking can occur after hours and on weekends so that daily LAN trafﬁ c is kept

to a minimum and users are not interrupted. The serverboard has a 3-pin header

(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has

WOL capability. Wake-On-LAN must be enabled in BIOS.

Wake-On-Ring Header (WOR)

Wake-up events can be triggered by a device such as the external modem ringing

when the system is in the SoftOff state.

1-6 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates.

The H8DI3+/I+(-F) Serverboard requires the use of proprietary power supplies.

Please refer to the pinout information for the power connectors in Section 6 of

Chapter 2 for detailed information on power requirements.

In areas where noisy power transmission is present, you may choose to install a

line ﬁ lter to shield the computer from noise. It is recommended that you also install

a power surge protector to help avoid problems caused by power surges.

Warning: To prevent the possibility of explosion, do not use the wrong type of

onboard CMOS battery or install it upside down.

Page is loading ...

Supermicro MNL-H8DI3+-F User manual

Brand: Supermicro

Model: MNL-H8DI3+-F

Category: Server/workstation motherboards

Type: User manual

Download PDF

report

Supermicro MNL-H8DI3+-F User manual

Supermicro MNL-H8DI3+-F User manual

Related papers

Other documents