Land Pride FPS User manual

Brand: Land Pride

Model: FPS

Category: Spreader

Type: User manual

Cover photo may show optional equipment

not supplied with standard unit.

Read the Accessory manual entirely. When

you see this symbol, the subsequent

instructions and warnings are serious - follow

without exception. Your life and the lives of

others depend on it!

Table of Contents

For utility vehicles with 2" receiver hitch,

DH10, DH15 & DH25 Disc Harrows, and FPS48

Electric Spin Spreader

5/24/16

701-162M

Accessory Manual

25609

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48 701-162M

5/24/16

Table of Contents

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, Land

Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves

the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1

Look For The Safety Alert Symbol . . . . . . . . . . . . . . 1

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Section 1: Assembly & Set-up . . . . . . . . . . . . 4

Electric Spin Spreader . . . . . . . . . . . . . . . . . . . . . . . 4

Mount Spreader To A Disc Harrow . . . . . . . . . . . . . 6

Mount Spreader To A Vehicle . . . . . . . . . . . . . . . . . 8

Section 2: Operating Procedures . . . . . . . . . 9

Calibrating the Spin Controller . . . . . . . . . . . . . . . . 9

Field Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Daily Operational Checks . . . . . . . . . . . . . . . . . . . 10

Cleaning And Storing . . . . . . . . . . . . . . . . . . . . . . 10

Spin Spreader Discharge Rates . . . . . . . . . . . . . . 10

Narrow Pattern Calculations . . . . . . . . . . . . . . . . 10

Wide Pattern Calculations . . . . . . . . . . . . . . . . . 10

Discharge Rate Table - 4 Ft. Spread Pattern . . . 11

Discharge Rate Table - 5 Ft. Spread Pattern . . . 12

Discharge Rate Table - 6 Ft. Spread Pattern . . . 13

Discharge Rate Table - Wide Spread Pattern . . 14

Section 3: Additional Equipment . . . . . . . . . 15

Additional Seeding Equipment . . . . . . . . . . . . . . . 15

Disc Harrow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Drag Harrow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Seed Bed Roller . . . . . . . . . . . . . . . . . . . . . . . . . 15

Complete One Pass Seeding Application . . . . . . 16

Section 4: Specifications . . . . . . . . . . . . . . . 17

Section 5: Features & Benefits . . . . . . . . . . 18

Section 6: Troubleshooting . . . . . . . . . . . . . 19

Section 7: Appendix . . . . . . . . . . . . . . . . . . . 20

Listing of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Parts Not Used . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Table of Contents

Important Safety Information

5/24/16

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Important Safety Information

▲

These are common practices that may or may not be applicable to the products described in

this manual.

Safety at All Times

Thoroughly read and understand

the instructions given in this

manual before operation. Refer to

the “Safety Label” section, read all

instructions noted on them.

Do not allow anyone to operate

this equipment who has not fully

read and comprehended this

manual and who has not been

properly trained in the safe

operation of the equipment.

▲ Operator should be familiar with

all functions of the Spin Spreader.

▲ Never allow children to operate

equipment.

▲ Operate Spin Spreader from the

driver’s seat only.

▲ Make sure all guards and shields

are in place and secured before

operating the Spin Spreader.

▲ Do not leave Spin Spreader

unattended with motor running.

▲ Keep hands, feet, and clothing

away from power-driven parts.

▲ Wear snug fitting clothing to avoid

entanglement with moving parts.

▲ Operating equipment safely

requires the full attention of the

operator. Avoid wearing radio

headphones while operating the

Spin Spreader.

Look For The Safety Alert Symbol

The SAFETY ALERT SYMBOL indicates there is a

potential hazard to personal safety involved and extra

safety precaution must be taken. When you see this

symbol, be alert and carefully read the message that

follows it. In addition to design and configuration of

equipment, hazard control and accident prevention

are dependent upon the awareness, concern,

prudence and proper training of personnel involved in

the operation, transport, maintenance and storage of

equipment.

Be Aware of

Signal Words

A Signal word designates a degree or

level of hazard seriousness. The

signal words are:

Indicates an imminently hazardous

situation which, if not avoided, will

result in death or serious injury. This

signal word is limited to the most

extreme situations, typically for

machine components that, for

functional purposes, cannot be

guarded.

DANGER

Indicates a potentially hazardous

situation which, if not avoided, could

result in death or serious injury, and

includes hazards that are exposed

when guards are removed. It may also

be used to alert against unsafe

practices.

Indicates a potentially hazardous

situation which, if not avoided, may

result in minor or moderate injury. It

may also be used to alert against

unsafe practices.

WARNING

CAUTION

Practice Safe Maintenance

▲ Understand procedure before doing

work. Use proper tools and

equipment, refer to Operator’s

Manual for additional information.

▲ Work in a clean dry area.

▲ Lower attached implement to the

ground and follow all shutdown

procedures before leaving the

operator’s seat to perform

maintenance.

▲ Allow implement to cool completely

before working on it.

▲ Disconnect battery ground cable (-)

before servicing or adjusting

electrical systems or before welding

on implement.

▲ Do not grease or oil implement

while it is in operation.

▲ Inspect all parts. Make sure parts

are in good condition & installed

properly.

▲ Replace parts on this machine with

genuine Land Pride parts only. Do

not alter this machine in a way

which will adversely affect its

performance.

▲ Remove buildup of grease, oil, and

debris.

▲ Remove all tools and unused parts

from implement before operation.

Important Safety Information

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

5/24/16

Table of Contents

These are common practices that may or may not be applicable to the products described in

this manual.

Keep Riders Off

Machinery

▲ Never carry riders or use

machinery as a person lift.

▲ Riders obstruct operator’s view.

▲ Riders could be struck by foreign

objects or thrown from the

machine.

▲ Never allow children to operate

equipment.

Wear

Protective Equipment

▲ Wear protective clothing and

equipment appropriate for the job

such as safety shoes, safety

glasses, hard hat, and ear plugs.

▲ Clothing should fit snug without

fringes and pull strings to avoid

entanglement with moving parts.

▲ Prolonged exposure to loud noise

can cause hearing impairment or

hearing loss. Wear suitable

hearing protection such as

earmuffs or earplugs.

▲ Operating equipment safely

requires the operator’s full

attention. Avoid wearing radio

headphones while operating

machinery.

Prepare for Emergencies

▲ Be prepared if a fire starts.

▲ Keep a first aid kit and fire

extinguisher handy.

▲ Keep emergency numbers for

doctor, ambulance, hospital, and

fire department near phone.

911

Use Seat Belt and ROPS

▲ Operate only utility vehicles and

tractors equipped with a Roll-Over

Protective Structure (ROPS) and

seat belt.

▲ Keep folding ROPS in the “locked

up” position at all times.

▲ Fasten seat belt snugly and

securely to help protect against

serious injury or death from falling

and machine overturn.

▲ Wear protective equipment such

as a hard hat, safety shoes, safety

glasses, and ear plugs.

Use Safety

Lights and Devices

▲ Slow moving tractors,

self-propelled equipment, and

towed implements can create a

hazard when driven on public

roads. They are difficult to see,

especially at night.

▲ Flashing warning lights and turn

signals are recommended

whenever driving on public roads.

Handle

Chemicals Properly

▲ Protective clothing should be

worn.

▲ Handle all chemicals with care.

▲ Follow instructions on container

label.

▲ Agricultural chemicals can be

dangerous. Improper use can

seriously injure persons, animals,

plants, soil, and property.

▲ Inhaling smoke from any type of

chemical fire is a serious health

hazard.

▲ Store or dispose of unused

chemicals as specified by the

chemical manufacturer.

Introduction

5/24/16

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Using This Manual

•

This Operator’s Manual is designed to help familiarize

you with safety, assembly, operation, adjustments,

troubleshooting, and maintenance. Read this manual

and follow the recommendations to help ensure safe

and efficient operation.

• The information contained within this manual was

current at the time of printing. Some parts may change

slightly to assure you of the best performance.

• To order a new manual contact your authorized dealer.

Manuals can also be downloaded, free-of-charge from

our website at www.landpride.com or printed from the

Land Pride Service & Support Center by your dealer.

Owner Assistance

If customer service or repair parts are required contact a

Land Pride dealer. A dealer has trained personnel, repair

parts and equipment needed to service the Electric Spin

Spreader.

The parts on your Electric Spin Spreader have been

specially designed and should only be replaced with

genuine Land Pride parts. Therefore, should your Spin

Spreader require replacement parts go to your Land

Pride Dealer.

Your dealer wants you to be satisfied with your new

Electric Spin Spreader. If for any reason you do not

understand any part of this manual or are not satisfied

with the service received, the following actions are

suggested:

1. Discuss the matter with your dealership service

manager making sure he is aware of any problems

you may have and that he has had the opportunity to

assist you.

2. If you are still not satisfied, seek out the owner or

general manager of the dealership, explain the

problem and request assistance.

3. For further assistance write to:

Land Pride Service Department

1525 East North Street

P.O. Box 5060

Salina, Ks. 67402-5060

E-mail address

lpservicedept@landpride.com

Introduction

Land Pride welcomes you to the growing family of new

product owners.

This Electric Spin Spreader has been designed with care

and built by skilled workers using quality materials. It is

exclusively designed to mount on the rear of a small

utility vehicle with a 2" receiver hitch such as ATV’s and

Land Pride Trekers. Also, it will fit on the back of any

Land Pride Disc Harrow, and FPS48. Please thoroughly

read these installation instructions, vehicle Operator

manual and Disc Harrow Operator Manual before

beginning. Especially read information relating to safety

concerns.

Proper assembly, maintenance and safe operating

practices will help you get years of satisfactory use from

your Electric Spin Spreader.

Application

The Land Pride Electric Spin Spreader is a highly

versatile full component package designed to plant or

spread seeds. It can then be used to spread prilled or

granulated fertilizer, lime, gypsum, and other soil

conditioning amendments at distances ranging from 4 ft.

to 20 ft. It can also be used in the off-season to spread

sand or salt for winter icing or slick snow conditions.

This unit has a 12volt remote tether control that can be

operated right from the driver’s seat to turn the spreader

on or off or to set the seed-gate opening to different

application rates.

The Spin Spreader has applications in overseeding of

pastures, grassy runways, open areas, roadsides,

medians, wild game food plots, hunting clubs, hunting

resorts, ranches, farms, game preserves, landscaping,

and hobby farming. It also works very well in gardens and

nurseries to incorporate fertilizer and pelletized gypsum

or lime as soil amendments.

Accessories are available for mounting the spreader to a

2" receiver hitch on a utility vehicle or a Land Pride Disc

Harrow. A Land Pride Drag Harrow and Seed Bed Roller

can be attached behind the Disc Harrow making your

Land Pride Disc Harrow, Spin Spreader, Drag Harrow

and Seed Bed Roller a complete seeding package.

General Information

These instructions apply to:

322-117A ELECTRIC SPIN SPREADER

322-100D EXTENSION TUBE, SPIN SPREADER

805-035C PIN BENT 1/2 X 3 WITH HAIRPIN

322-264A HITCH MOUNT W/REAR HITCH

890-975C 2" BALL HITCH 3500LB 3/4 THRD

890-971C TOW HOOK (LOAD 10,000 LBS)

Section 1: Assembly & Set-up

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

5/24/16

Table of Contents

Electric Spin Spreader

Refer to Figure 1-1 on page 5:

322-117A ELECTRIC SPIN SPREADER

A detailed listing of parts for the Spin Spreader is

provided on page 22. Use the list as a checklist to

inventory parts received. Please contact your local Land

Pride dealer for any missing hardware.

Install the Electric Spin Spreader as follows:

1. Remove Spin Spreader and all component from the

shipping boxes.

2. Attach spin motor (#16) to hitch weldment (#34) with

flat washers (#28) and 10-32 hex nuts (#27). Tighten

hex nuts to the correct torque.

3. Attach spreader distribution plate (#15) to the motor

shaft with cotter pin (#14). Spread one or more legs of

cotter pin to keep it from falling out.

4. Attach spreader back plate (#31) to spreader hitch

weldment (#34) with 8-32 x 2" Phillips head

screws (#36) and hex nylock nuts (#35). Tighten

nylock nuts. See “NOTE” under “Parts Not Used”

on page 25 for shipping location of nylock nuts (#35)

and screws (#36).

5. Attach left-hand and right-hand straps (#29 & #30) to

hitch weldment (#34) as shown with 5/16"-18 x 2 1/2"

GR5 lower bolt (#23) and nylock nut (#25). Screw nut

on 2 or 3 turns. Do not tighten at this time.

6. Attach left-hand and right-hand straps (#29 & #30) to

hitch weldment (#34) as shown with 5/16"-18 x 3"

GR5 all thread upper bolt (#22) and nylock nut (#25).

Screw nut on 2 or 3 turns. Do not tighten at this time.

7. Attach left-hand and right-hand straps (#29 & #30)

together at the back with 5/16"-18 x 3" GR5 all thread

bolt (#22), 3/4" long spacer (#21), and nylock

nut (#25). Screw nut on 2 or 3 turns. Do not tighten at

this time.

8. Attach Flow regulator (#18) directly below hole “H” in

spreader tank (#1) as shown with 8-32 hex

nuts (#2A). Tighten hex nuts.

9. (Optional) Attach restrictor plate (#3) on top of

existing nuts (#2A) with 8-32 hex huts (#2B). Tighten

nuts.

NOTE: Not all components included in the shipping

box will be used. See “Parts Not Used” on page 25.

IMPORTANT: Drive “G” for Flow regulator (#18)

is located directly below hole “H” in spreader

tank (#19).

NOTE: The restrictor plate (#3) is used to decrease

the discharge rate of product flow out the two hopper

openings. Some applications will require that the

restrictor plate be removed. Other applications will

require that the restrictor plate be installed.

10. Slide spreader tank (#19) between left and right-

hand straps (#29 & #30).

11. Hand screw 1/2"-13 hex nut (#24) on eye bolt (#33)

until nut has bottomed out on the threads.

12. Insert eye bolt (#33) through hitch weldment (#34),

hole “H” in tank (#19), formed washer (#37), and hex

nylock nut (#26). Draw nylock nut up until 1 to 2

threads are pass the nylock nut. Do not tighten

nut (#24) or nylock nut (#26) at this time.

13. Adjust left-hand and right-hand straps (#29 & #30) to

fit between beads in spreader tank (#1) and tighten

the front two 5/16"-18 hex nylock nuts (#25) to the

correct torque for GR5 bolts and then the back nylock

nut (#25) to the correct torque.

14. Hold eye in eye bolt (#33) vertical with a screwdriver

or drive punch and tighten nylock nut (#24) against

hitch weldment (#34) until tight.

15. Insert wiring for spin motor (#16) into wire clip (#7) as

shown with mounting holes in clip up. Skid to step 17

if attaching spin deflector (#4).

16. Attach wire clip (#7) on inside of channel to hole “F”

with 1/4"-20 x 3/4" GR5 hex flange serrated

screw (#8), flat washer (#6), and wing nut (#5). Hand

tighten wing nut. Skip to step 18.

17. Attach optional spin deflector as follows:

a. Attach spin deflector (#4) and wire clip (#7) on

inside of channel to hole “F” with 1/4"-20 x 3/4"

GR5 hex flange serrated screw (#8), flat washer

(#6), and wing nut (#5). Hand tighten wing nut.

b. Complete attachment of spin deflector (#4) to the

remaining 3 holes using 1/4"-20 x 3/4" GR5 hex

flange serrated screws (#8), flat washers (#6),

and wing nuts (#5). Hand tighten wing nuts

18. Fully insert cap plug (#12) in tank lid (#20) as shown.

19. Attach tank lid (#20) to spreader hopper (#19).

20. Attach large square tube cap (#32) to top of hitch

weldment tube “J”.

21. Cable ties (#11), hand control (#17), and tie down

straps (#13) will be installed after mounting the Spin

Spreader to a FPS, utility vehicle, or disc harrow.

NOTE: Spin deflector (#4) is used to reduce the

broadcast spread pattern to as small as 48". Install

the spin deflector only if a desired spread pattern

width is needed.

Installation Note: The spin deflector (#4) can be

installed without removing the hopper from its mount.

Simply slide the deflector between hopper (#19) and

spin plate (#15).

IMPORTANT: Tie down straps (#13) must be used

with spreader to protect against damage to spreader

and supporting structures.

Section 1: Assembly & Set-up

5/24/16

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Figure 1-1

25786

Section 1: Assembly & Set-up

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

5/24/16

Table of Contents

Mount Spreader To A Disc Harrow

Refer to Figure 1-2 on page 7:

322-264A Hitch Mount With Rear Hitch for Disc Harrow

A detailed listing of parts for the hitch mount and rear

hitch is provided on page 24. Use the list as a checklist to

inventory parts received. Please contact your local Land

Pride dealer for any missing hardware.

1. Park Disc Harrow on a flat surface, move gear shift

lever to park or to neutral and set park brake, turn

engine switch to off and remove ignition key.

2. Attach spin spreader mounting bracket (#22) to the

Disc Harrow rear cross tube (M) with two 3/8"-16

U-bolts (#23 or #24 or #25) and two 3/8" flange lock

nuts (#26). See note above. Make certain the bracket

is centered on the tube and then tighten U-bolts to

the correct torque.

3. Slide spreader mounting bracket (G) over Spin

Spreader extension tube (#22). Secure in place with

5/16" x 2 1/2" clevis pin (#9) and hair pin cotter (#10).

4. Attach one end of each ratchet tie down straps (#13)

to the spreader eyebolt (L) and the other ends to the

Disc Harrow in a V-pattern as shown.

5. Tighten tie down straps to prevent spreader box from

jiggling in its mount. Do not over tighten.

6. Plug hand control white connector (A) into feedgate

connector (B).

7. Plug hand control black connector (C) into spin motor

connector (D).

8. Plug lighter plug (E) into a 12 volt accessory

receptacle.

9. Secure wiring harness for controller (#15) with cable

ties (#11).

10. Attach rear hitch (#27) to spreader mount (#22) with

3/4" clevis pins (#28) and 5/32" cotter pins (#29).

Bend one leg of each cotter pin to keep it in place.

NOTE: Hardware bag consist of 3 different sizes of

U-bolts. Use the correct U-bolt size that matches the

Disc Harrow rear cross tube.

• DH10 Series (#23) U-bolt 3/8"-16 x 2 x 2 3/4"

• DH15 Series (#24) U-bolt 3/8"-16 x 3 1/32 x 3 1/2"

• DH25 Series (#25) U-bolt 3/8"-16 x 3 1/32 x 4"

IMPORTANT: Tie down straps (#13) must be used

with spreader to protect against damage to spreader

and supporting structures.

IMPORTANT: Not securing Spin Spreader with tie

down straps will result in MOUNT DAMAGE.

11. Attach one of three hitches listed below to the rear

hitch tube. See page 24 for a detailed listing of parts.

Hitch Plate (Standard)

a. Attach hitch plate (#32) to rear hitch tube (#27)

with 1/2"-13 x 3 1/2" GR5 hex flange screw s(#30)

and hex flange lock nuts (#31).

b. Tighten lock nuts to the correct torque.

c. Insert 3/8" x 5 1/8" long detent hitch pin (#33) into

hitch plate (#32).

2" Ball Hitch Part No. 890-975C (Option)

a. Attach hitch plate (#32) to rear hitch tube (#27)

per instructions above.

b. Attach 2" ball (#35) to hitch plate (#32).

c. Tighten ball nut to the correct torque.

Tow Hook Part No. 890-971C (Option)

a. Remove hitch plate (#32).

b. Attach tow hook (#34) to rear hitch tube (#27) with

1/2"-13 x 3 1/2" GR5 hex flange screws (#30) and

hex flange lock nuts (#31).

c. Tighten lock nuts to the correct torque.

Section 1: Assembly & Set-up

5/24/16

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Figure 1-2

25788

Section 1: Assembly & Set-up

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

5/24/16

Table of Contents

Mount Spreader To A Vehicle

Refer to Figure 1-3:

A detailed listing of parts for the extension tube (#18) &

bent pin (#19) is provided on page 24. Use the list as a

checklist to inventory parts received. Please contact your

local Land Pride dealer for any missing hardware.

1. Park vehicle on a flat surface, move gear shift lever to

park or to neutral and set park brake, turn engine

switch to off and remove ignition key.

2. Attach Spin Spreader extension tube (#18) to your

vehicle’s 2" receiver hitch with bent pin (#19). Secure

with hair pin cotter included with the bent pin.

3. Slide spreader mounting bracket (G) over Spin

Spreader extension tube (#18). Secure in place with

5/16" x 2 1/2" clevis pin (#9) and hair pin cotter (#10).

IMPORTANT: Tie down straps (#13) must be used

with spreader to protect against damage to spreader

and supporting structures.

4. Attach one end of each ratchet tie down strap (#13) to

the spreader eyebolt (L) and the other ends to the

vehicle in a V-pattern as shown.

5. Tighten tie down straps to prevent spreader box from

jiggling in its mount. Do not over tighten.

6. Plug hand control white connector (A) into feedgate

connector (B).

7. Plug hand control black connector (C) into spin motor

connector (D).

8. Plug lighter plug (E) into a 12 volt accessory

receptacle.

9. Secure controller wiring harness (#15) with cable

ties (#11).

IMPORTANT: Not securing Spin Spreader with tie

down straps will result in MOUNT DAMAGE.

Figure 1-3

25787

Section 2: Operating Procedures

5/24/16

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Calibrating the Spin Controller

Refer to Figure 2-4:

Spin Spreader Control

Figure 2-4

1. Thoroughly lubricate the spreader before calibrating.

2. Calibrate the control unit by holding the OFF button

down and momentarily pressing the ON button.

While in the calibration mode, the lights will flash

rapidly. Once calibration is complete, the lights will go

out and the gate will close. The unit is now ready for

operation.

3. Set dispensing amount by pressing the MORE or

LESS buttons to achieve the desired gate opening.

Position 1 is the minimum amount and position 6 is

the maximum amount of material flow. The Material

Flow light flashes when unit is not running (OFF) and

is on solid when unit is running (ON).

4. While moving at a constant rate, start material

spreading by pressing the ON button.

5. Press the OFF button to stop the spin motor and

close the control gate.

IMPORTANT: To assure proper operation, the

Electric Spin Spreader controls should be calibrated

each time it is plugged into the 12 volt receptacle or

if you loose power to receptacle.

IMPORTANT: Make sure the Spin Spreader is

empty and the vehicle is running when calibrating.

23910

NOTE: The MORE or LESS buttons may be

pressed at anytime to achieve the desired material

flow rate.

Field Set-up

CAUTION

Wear eye protection to prevent getting chemicals and/or dirt

in the eyes while cleaning the Electric Spin Spreader.

CAUTION

Be sure to wear proper protective clothing when servicing or

lubricating your spin seeder. Refer to chemical

manufacturers’ labels for specific clothing requirements.

1. Prior to operation, thoroughly lubricate the Spin

Spreader. Check for proper operation of the

mechanisms by running the spin motor and slide

gate at no-load. See “Calibrating the Spin Controller”

on this page.

2. Review spreader rate tables on pages 11 through 14.

Make initial setting at the controller (positions 1

through 6) and install or remove the restrictor plate as

needed.

3. Install the spin deflector if a narrow pattern is desired

or remove the spin deflector if a full width pattern is

preferred.

4. Press the OFF button to make sure the Spin

Spreader gate is closed and then fill the bin with

product.

5. Make a run with the Spin Spreader turned on to

check product dispersion rate.

IMPORTANT: Always make sure you are traveling

before turning the Spin Spreader on. Always turn the

Spin Spreader off before end of travel. Running the

spreader while not traveling will discharge too much

material in one spot.

NOTE: A good method for checking product

dispersion is to fill the bin with the required pounds

of material to cover 1,000 sq. ft. in a straight run. A

4 ft. wide pattern would require 250 ft. of straight run.

You should run out of product at the end of the 250

ft. If not, make the following adjustments:

1. Increase travel speed to disperse less product

per sq. ft. or decrease speed to disperse more.

2. If the speed you are traveling is preferred,

change position number on the controller to

disperse more or less product.

3. You may also want to adjust the spin deflector at

the wing nuts to control placement of product.

4. Make a new run to recheck dispersion rate.

Section 2: Operating Procedures

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

5/24/16

Table of Contents

Daily Operational Checks

1. Clean the unit of dirt and trash to minimize rusting

and wear.

2. Visually inspect all nuts for tightness.

3. Replace any decals that are worn or damaged.

4. Prior to operation, thoroughly lubricate the Spin

Spreader.

5. Check for proper operation of the mechanisms by

running the machine at no-load for a few minutes.

6. Calibrate spin controller and spin deflector for

spreading the quantity desired and recheck

adjustments for accuracy.

7. All spreader parts must be cleaned properly after

every use to extend its life and efficiency.

Cleaning And Storing

CAUTION

Wear eye protection to prevent getting chemicals and/or dirt

in the eyes while cleaning the Spin Spreader.

CAUTION

Be sure to wear proper protective clothing when servicing or

lubricating your Fertilizer Spreader. Refer to chemical

manufacturers’ labels for specific clothing requirements.

Fertilizer is extremely corrosive and all remaining

particles including dust particles should be removed from

the spreader soon after application.

1. Remove all product left in the holding tank.

2. Disconnect and store spin controller in a dry location.

3. DO NOT wash the feedgate with water. Remove the

two screws from the bottom of the gate and slide the

gate forward until it drops off the unit. Be careful not

to loose the screws.

4. Use a soft bristle brush to clean the felt and remove

any dust from around the gear or on the felt.

5. Completely wash the rest of the Spin Spreader with

water and dry thoroughly.

6. Add a light coat of oil on all metal parts and motor to

help prevent rusting and corrosion.

7. Reinstall the feedgate.

8. Store the Electric Spin Spreader and electrical

controls in a location that is sheltered from moisture.

Spin Spreader Discharge Rates

DISCLAIMER: The Discharge Rate Tables are intended

as guidelines only. Land Pride accepts no responsibility

for actual site application rates or germination rates.

IMPORTANT: Remove spin controller and

discharge gate before washing the Spin Spreader.

These rates can vary dramatically due to varying

conditions and operator skill level.

Narrow Pattern Calculations

Calculations in the Discharge Rate Tables on page 11 for

narrow patterns (4’, 5’ & 6’ widths) are based on:

• With and without a restrictor plate installed.

• With the spin deflector attached.

• Dispersal pattern at 48" width.

• Traveling at 1 MPH (mile per hour)

EXAMPLE:

If you are traveling 1 MPH and dispersing a 4’ wide

pattern of alfalfa using flow position 2, your discharge

rate is 515.63 lbs/acre or 11.84 lbs/1000 sq. ft. at 1 MPH

(See Discharge Rate Table on page 11). If you are

driving at 4 MPH, calculate the discharge rate as follows:

• Divide 515.63 by 4 = 128.91 lbs/acre.

• Divide 11.84 by 4 = 2.96 lbs/1000 sq. ft.

REMEMBER: Increasing travel speed decreases the

amount of material being applied.

Wide Pattern Calculations

Calculations in the Discharge Rate Tables on page 14 for

the wide pattern spreader rates are based on:

• With the spin deflector removed.

• With and without a restrictor plate installed.

• Dispersal pattern at widths indicated in the table.

• Traveling at 1 MPH (mile per hour)

EXAMPLE:

If you are traveling 1 MPH and dispersing a 4’ wide

pattern of alfalfa using flow position 2, your discharge

rate is 103.13 lbs/acre or 2.37 lbs/1000 sq. ft. at 1 MPH

(See Spreader Rate table on page 14). If you are driving

at 5 MPH, calculate the discharge rate as follows:

• Divide 103.13 by 5 = 20.63 lbs/acre.

• Divide 2.37 by 5 = 0.47 lbs/1000 sq. ft.

REMEMBER: Increasing travel speed decreases the

amount of material being applied.

NOTE: If vehicle does not have a speed meter or no

way to calculate speed, a hand held Global

Positioning System (GPS) that indicates speed is

available at most sporting goods stores.

NOTE: Data in the Discharge Rate Tables is based

on traveling at 1 MPH. To calculate discharge rate

when traveling at a different speed, divide the data

in the table by the MPH you are traveling.

NOTE: Data in the Discharge Rate Tables is based

on traveling at 1 MPH. To calculate discharge rate

when traveling at a different speed, divide the data

in the table by the MPH you are traveling.

Section 2: Operating Procedures

5/24/16

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Discharge Rate Table - 4 Ft. Spread Pattern @ 1 MPM

Alfalfa Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 129.94 515.63 1108.80 1817.06 2003.93 1989.90

Lbs/1000 sq. ft. 2.98 11.84 25.45 41.71 46.00 45.68

Unrestricted

Restrictor required (See above data with restrictor)

Biologic Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 100.65 312.68 405.08 481.80

Lbs/1000 sq. ft. 0.00 0.00 2.31 7.18 9.30 11.06

Unrestricted Lbs/acre 0.00 41.25 154.28 348.98 644.33 1574.10

Lbs/1000 sq. ft. 0.00 0.95 3.54 8.01 14.79 36.14

MegaPlot Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 821.29 1884.30

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 18.85 43.26

EasyPlot Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 0.00 419.93

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 0.00 9.64

Clover (Ladina) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 147.26 620.40 1161.60 1908.64 2101.28 2151.60

Lbs/1000 sq. ft. 3.38 14.24 26.67 43.82 48.24 49.39

Unrestricted

Restrictor required (See above data with restrictor)

Clover (Red) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 92.81 348.56 750.34 1256.06 1499.44 1835.63

Lbs/1000 sq. ft. 2.13 8.00 17.23 28.84 34.42 42.14

Unrestricted

Restrictor required (See above data with restrictor)

Clover (Yellow Sweet) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 482.63 1586.48 1701.98 1706.51 1715.18 1805.10

Lbs/1000 sq. ft. 11.08 36.42 39.07 39.18 39.38 41.44

Unrestricted

Restrictor required (See above data with restrictor)

Oats Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 152.21 1020.94 1172.33 2074.88

Lbs/1000 sq. ft. 0.00 0.00 3.49 23.44 26.91 47.63

Ryegrass (annual) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 121.28 358.05 469.84 502.43 525.94

Lbs/1000 sq. ft. 0.00 2.78 8.22 10.79 11.53 12.07

Unrestricted Lbs/acre 0.00 363.41 999.90 1810.05 3410.55 0.00

Lbs/1000 sq. ft. 0.00 8.34 22.95 41.55 78.30 0.00

Sorghum Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 215.74 614.63 1001.96 1041.56 1059.71

Lbs/1000 sq. ft. 0.00 4.95 14.11 23.00 23.91 24.33

Unrestricted

Restrictor required (See above data with restrictor)

Soybeans Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 0.00 1541.51

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 0.00 35.39

Gypsum (pelletized) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 1027.54 3557.40 5568.75 5999.40

Lbs/1000 sq. ft. 0.00 0.00 23.59 81.67 127.84 137.73

Prilled Fertilizer Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 852.23 1196.25 1228.84 1234.61

Lbs/1000 sq. ft. 0.00 0.00 19.56 27.46 28.21 28.34

Unrestricted Lbs/acre 0.00 742.50 2148.30 4244.63 6761.70 7212.15

Lbs/1000 sq. ft. 0.00 17.05 49.32 97.44 155.23 165.57

Sand Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 573.79 1564.20 2047.65 2716.73

Lbs/1000 sq. ft. 0.00 0.00 13.17 35.91 47.01 62.37

Unrestricted Lbs/acre 0.00 0.00 1536.56 4050.75 5443.35 7154.40

Lbs/1000 sq. ft. 0.00 0.00 35.27 92.99 124.96 164.24

Salt Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 593.59 972.68 1060.13 1133.96

Lbs/1000 sq. ft. 0.00 0.00 13.63 22.33 24.34 26.03

Unrestricted Lbs/acre 0.00 848.51 3460.88 6857.40 9820.80 10513.80

Lbs/1000 sq. ft. 0.00 19.48 79.45 157.42 225.45 241.36

Section 2: Operating Procedures

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

5/24/16

Table of Contents

Discharge Rate Table - 5 Ft. Spread Pattern @ 1 MPM

Alfalfa Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 103.95 412.50 887.04 1453.65 1603.14 1591.92

Lbs/1000 sq. ft. 2.38 9.47 20.36 33.37 38.80 36.54

Unrestricted

Restrictor required (See above data with restrictor)

Biologic Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 80.52 250.14 324.06 385.44

Lbs/1000 sq. ft. 0.00 0.00 1.85 5.74 7.44 8.85

Unrestricted Lbs/acre 0.00 33.00 123.42 279.18 515.46 1259.28

Lbs/1000 sq. ft. 0.00 .76 2.83 6.41 11.83 28.91

MegaPlot Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 657.03 1507.44

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 15.08 34.61

EasyPlot Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 0.00 335.94

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 0.00 7.71

Clover (Ladina) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 117.81 496.32 929.28 1526.91 1681.02 1721.28

Lbs/1000 sq. ft. 2.70 11.39 21.34 35.06 38.59 39.51

Unrestricted

Restrictor required (See above data with restrictor)

Clover (Red) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 74.25 278.85 600.27 1004.85 1199.55 1468.50

Lbs/1000 sq. ft. 1. 7 0 6.40 13.78 23.07 27.54 33.71

Unrestricted

Restrictor required (See above data with restrictor)

Clover (Yellow Sweet) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 386.10 1269.18 1361.58 1365.21 1372.14 1444.08

Lbs/1000 sq. ft. 8.86 29.14 31.26 31.34 31.50 33.15

Unrestricted

Restrictor required (See above data with restrictor)

Oats Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 121.77 816.75 937.86 1659.90

Lbs/1000 sq. ft. 0.00 0.00 2.79 18.75 21.53 38.10

Ryegrass (annual) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 97.02 286.44 375.87 401.94 420.75

Lbs/1000 sq. ft. 0.00 2.22 6.58 8.63 9.22 9.66

Unrestricted Lbs/acre 0.00 290.73 799.92 1448.04 2728.44 0.00

Lbs/1000 sq. ft. 0.00 6.67 18.36 33.24 62.64 0.00

Sorghum Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 172.59 491.7 801.57 833.25 847.77

Lbs/1000 sq. ft. 0.00 3.96 11.29 18.40 19.13 19.47

Unrestricted

Restrictor required (See above data with restrictor)

Soybeans Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre L0.00 0.00 0.00 0.00 0.00 1233.21

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 0.00 28.31

Gypsum (pelletized) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 822.03 2845.92 4455.00 4799.52

Lbs/1000 sq. ft. 0.00 0.00 18.87 65.34 102.27 110.18

Prilled Fertilizer Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 681.78 957.00 983.07 987.69

Lbs/1000 sq. ft. 0.00 0.00 15.65 21.97 22.57 22.67

Unrestricted Lbs/acre 0.00 594.00 1718.64 3395.70 5409.36 5769.72

Lbs/1000 sq. ft. 0.00 13.64 39.46 77.95 124.18 132.46

Sand Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 459.03 1251.36 1638.12 2173.38

Lbs/1000 sq. ft. 0.00 0.00 10.54 28.73 37.61 49.90

Unrestricted Lbs/acre 0.00 0.00 1229.25 3240.60 4354.68 5723.52

Lbs/1000 sq. ft. 0.00 0.00 28.22 74.39 99.97 131.39

Salt Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 474.87 778.14 848.1 907.17

Lbs/1000 sq. ft. 0.00 0.00 10.90 17.86 19.47 20.82

Unrestricted Lbs/acre 0.00 678.81 2768.70 5485.92 7856.64 8411.04

Lbs/1000 sq. ft. 0.00 15.58 63.56 125.49 180.36 193.09

Section 2: Operating Procedures

5/24/16

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Discharge Rate Table - 6 Ft. Spread Pattern @ 1 MPM

Alfalfa Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 86.63 343.75 739.20 1211.37 1335.95 1326.60

Lbs/1000 sq. ft. 1.99 7.89 16.97 27.81 30.67 30.45

Unrestricted

Restrictor required (See above data with restrictor)

Biologic Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 67.10 208.45 270.05 321.20

Lbs/1000 sq. ft. 0.00 0.00 1.54 4.79 6.20 7.37

Unrestricted Lbs/acre 0.00 27.50 102.85 232.65 429.55 1049.4

Lbs/1000 sq. ft. 0.00 .63 2.36 5.34 9.86 24.09

MegaPlot Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 547.53 1256.2

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 12.57 28.84

EasyPlot Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 0.00 279.95

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 0.00 6.43

Clover (Ladina) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 98.17 413.60 774.40 1272.43 1400.85 1434.40

Lbs/1000 sq. ft. 2.25 9.49 17.78 29.21 32.16 32.93

Unrestricted

Restrictor required (See above data with restrictor)

Clover (Red) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 61.87 232.37 500.23 827.37 999.63 1223.75

Lbs/1000 sq. ft. 1. 4 2 5.33 11.4 9 19.23 22.95 28.09

Unrestricted

Restrictor required (See above data with restrictor)

Clover (Yellow Sweet) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 321.75 1057.65 1134.65 1137.67 1143.45 1203.4

Lbs/1000 sq. ft. 7.39 24.28 26.05 26.12 26.25 27.63

Unrestricted

Restrictor required (See above data with restrictor)

Oats Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 101.47 680.63 781.55 1383.25

Lbs/1000 sq. ft. 0.00 0.00 2.33 15.63 17.94 31.75

Ryegrass (annual) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 80.85 238.70 313.23 334.95 350.63

Lbs/1000 sq. ft. 0.00 1.85 5.48 7.19 7.69 8.05

Unrestricted Lbs/acre 0.00 242.27 666.60 1206.70 2273.70 0.00

Lbs/1000 sq. ft. 0.00 5.56 15.30 27.70 52.20 0.00

Sorghum Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 143.83 409.75 667.97 694.37 706.47

Lbs/1000 sq. ft. 0.00 3.30 9.41 15.33 15.94 16.22

Unrestricted

Restrictor required (See above data with restrictor)

Soybeans Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 0.00 1027.67

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 0.00 23.59

Gypsum (pelletized) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 685.03 2371.60 3712.50 3999.60

Lbs/1000 sq. ft. 0.00 0.00 15.73 54.45 85.23 91.82

Prilled Fertilizer Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 568.15 797.15 819.23 823.07

Lbs/1000 sq. ft. 0.00 0.00 13.04 18.31 18.81 18.89

Unrestricted Lbs/acre 0.00 495.00 1432.20 2829.75 4507.80 4808.10

Lbs/1000 sq. ft. 0.00 11.37 32.88 64.96 103.49 110.38

Sand Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 382.53 1042.80 1365.10 1811.15

Lbs/1000 sq. ft. 0.00 0.00 8.78 23.94 31.34 41.58

Unrestricted Lbs/acre 0.00 0.00 1024.37 2700.50 3628.90 4769.60

Lbs/1000 sq. ft. 0.00 0.00 23.51 61.99 83.31 109.49

Salt Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 395.73 648.45 706.75 755.97

Lbs/1000 sq. ft. 0.00 0.00 9.09 14.89 16.23 17.35

Unrestricted Lbs/acre 0.00 565.67 2307.25 4571.60 6547.20 7009.20

Lbs/1000 sq. ft. 0.00 12.99 52.97 104.95 150.30 160.91

Section 2: Operating Procedures

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

5/24/16

Table of Contents

Discharge Rate Table - Wide Spread Pattern @ 1 MPM

Alfalfa (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 25.99 103.13 221.76 363.41 400.79 397.98

Lbs/1000 sq. ft. 0.60 2.37 5.09 8.34 9.20 9.14

Unrestricted

Restrictor required (See above data with restrictor)

Biologic (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 20.13 62.54 81.02 96.36

Lbs/1000 sq. ft. 0.00 0.00 0.46 1.44 1.86 2.21

Unrestricted Lbs/acre 0.00 8.25 30.86 69.80 128.87 314.82

Lbs/1000 sq. ft. 0.00 .19 0.71 1.60 2.96 7.23

MegaPlot (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 164.26 376.86

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 3.77 8.65

EasyPlot (12 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 0.00 139.98

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 0.00 3.21

Clover (Ladina) (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 29.45 124.08 232.32 381.73 420.26 430.32

Lbs/1000 sq. ft. 0.68 2.85 5.33 8.76 9.65 9.88

Unrestricted

Restrictor required (See above data with restrictor)

Clover (Red) (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 18.56 69.7 150.07 251.21 299.89 367.13

Lbs/1000 sq. ft. 0.43 1. 6 0 3.45 5.77 6.88 8.43

Unrestricted

Restrictor required (See above data with restrictor)

Clover (Yellow Sweet) (20 ft.Spread Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 96.53 317.30 340.40 341.30 343.04 361.02

Lbs/1000 sq. ft. 2.22 7.28 7.81 7.84 7.88 8.29

Unrestricted

Restrictor required (See above data with restrictor)

Oats (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 24.35 163.35 187.57 331.98

Lbs/1000 sq. ft. 0.00 0.00 0.56 3.75 4.31 7.62

Ryegrass (annual) (12 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 40.43 119.35 156.61 167.48 175.31

Lbs/1000 sq. ft. 0.00 0.93 2.74 3.60 3.84 4.02

Unrestricted Lbs/acre 0.00 121.14 333.30 603.35 1136.85 0.00

Lbs/1000 sq. ft. 0.00 2.78 7.65 13.85 26.10 0.00

Sorghum (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 34.52 98.34 160.31 166.65 169.55

Lbs/1000 sq. ft. 0.00 0.79 2.26 3.68 3.83 3.89

Unrestricted

Restrictor required (See above data with restrictor)

Soybeans (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 0.00 0.00 0.00 246.64

Lbs/1000 sq. ft. 0.00 0.00 0.00 0.00 0.00 5.66

Gypsum (pelletized) (20 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor

Not Compatible with restrictor

Unrestricted Lbs/acre 0.00 0.00 205.51 711.48 1113.75 1199.88

Lbs/1000 sq. ft. 0.00 0.00 4.72 16.33 25.57 27.55

Prilled Fertilizer (21 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 162.33 227.86 234.06 235.16

Lbs/1000 sq. ft. 0.00 0.00 3.73 5.23 5.37 5.40

Unrestricted Lbs/acre 0.00 141.43 409.20 808.50 1287.94 1373.74

Lbs/1000 sq. ft. 0.00 3.25 9.39 18.56 29.57 31.54

Sand (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 91.81 250.27 327.62 434.68

Lbs/1000 sq. ft. 0.00 0.00 2.11 5.75 7.52 9.98

Unrestricted Lbs/acre 0.00 0.00 245.85 648.12 870.94 1144.70

Lbs/1000 sq. ft. 0.00 0.00 5.64 14.88 19.99 26.28

Salt (25 ft.Spreading Width) Position 1 Position 2 Position 3 Position 4 Position 5 Position 6

W/Restrictor Lbs/acre 0.00 0.00 94.97 155.63 169.62 181.43

Lbs/1000 sq. ft. 0.00 0.00 2.18 3.57 3.89 4.17

Unrestricted Lbs/acre 0.00 135.76 553.74 1097.18 1571.33 1682.21

Lbs/1000 sq. ft. 0.00 3.12 12.71 25.19 36.07 38.62

Section 3: Additional Equipment

5/24/16

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Drag Harrow (6’ x 4’ Shown)

Figure 3-2

Seed Bed Roller

Refer to Figure 3-3:

The Land Pride SBR72 Three-point hitch or pull type

Seed Bed Roller has uses and applications in

landscaping, sports field maintenance, pasture

maintenance, professional turf care, general seeding

and overseeding applications around home sites,

construction sites, horse paddocks, nurseries, sod

farms, and small farm or ranch operations. The SBR72

will break up smaller clumps and dirt clods, while

pressing applied seed into firm contact with the soil

profile for greatly improved germination rates. The

notched profile of the roller also develops a pattern of

uniformly spaced mini-furrows that tend to hold seed and

fertilizer in place. These small furrows also retain

essential moisture, and resist erosion from the wind and

runoff from applied irrigation or rain. It can be pulled

behind the Electric Spin Spreader or behind any machine

equipped with a drawbar or receiver hitch. The hitch on

the tongue can be set-up as a clevis hitch or turned

around for a ball hitch.

SBR72 Set-up for Pull Type Hook-Up

Figure 3-3

25611

25762

Section 3: Additional Equipment

Additional Seeding Equipment

Disc Harrow

Refer to Figure 3-1:

Land Pride Disc Harrows are designed to open and break

up soil surface in preparation for planting.

Land Pride Disc Harrow Models

Model DH1048 & DH1060 . . . . . . . . . 48" & 60" Wide

Model DH1560 & DH1572 . . . . . . . . . . 60" & 72" wide

Model DH2572 & DH2584 . . . . . . . . . .72" & 84" wide

Additional equipment can be attached behind the Disc

Harrow to make it a complete seeding package. See

“Complete One Pass Seeding Application” on page 16.

Electric Spin Spreader Assembly (DH Series)

Figure 3-1

Drag Harrow

Refer to Figure 3-2:

The Land Pride Drag Harrows are designed for various

types of seedbed and ground preparations. They can be

used to smooth out freshly cultivated soil, work seed and

fertilizer into freshly cultivated soil or into turf and pasture

grass, fluff and level arenas, aerate soil for faster

dry-down time, de-thatch and aerate lawns and pastures,

break up aeration cores on turf surfaces and groom

snow-packed ski resorts.

The Drag Harrow can also be used in tandem with Land

Pride’s Disc Harrow, Electric Spin Spreader and Seed

Bed Roller to provide a highly efficient and complete

seeding application in one pass. See “Complete One

Pass Seeding Application” on page 16.

Land Pride Drag Harrow Models

Model DRG04 . . . . . . . . . . . . . . . . 4 ft. wide x 4 ft. long

Model DRG06 . . . . . . . . . . . . . . . . 6 ft. wide x 4 ft. long

Model DRG08 . . . . . . . . . . . . . . . 8 ft. wide x 4 ft. long

Section 3: Additional Equipment

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

5/24/16

Table of Contents

Refer to Figure 3-4:

Remove the tongue and rotate the remaining A-frame

hitch up 90 degrees and it becomes a 3-point mounted

Seed Bed Roller.

SBR72 Set-up for 3-Point Hook-Up

Figure 3-4

25763

Complete One Pass Seeding Application

Figure 3-5

Complete One Pass Seeding Application

Refer to Figure 3-5:

Land Prides offers a Seeder/Overseeder component

system for one-pass ground cultivation and seed to soil

integration for applications on previously tilled soil,

existing pasture ground, large grassy areas, reclamation

sites and wild game food plots. This system is comprised

of a Land Pride DH10, DH15 or DH25 Series Disc

Harrow, rear mounted Electric Spin Spreader with

special hitch kit, trailing DRG04, DRG06 or DRG08 Drag

Harrow, and trailing pull-type SBR72 Seed Bed Roller.

See your nearest Land Pride Dealer for more information

or visit our web site at www.landpride.com.

Section 4: Specifications

5/24/16

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

Table of Contents

Section 4: Specifications

Electric Spin Spreader Specifications

Description Specification

Spin Spreader Volume/Capacity 2 cu. ft. (15 gallons) (100 lbs. Maximum capacity weight)

Hopper Construction Poly with water tight poly press fit lid.

Deflector Ring Construction Poly construction and removable and adjustable.

Frame Construction Welded and formed steel tubing and sheet metal.

Wide Spread Pattern

Without Deflector

20 to 25 ft. (Actual spread pattern is dependent upon product type and condition during

application.)

Spin Spreader Deflector Diverts and restricts seed to smaller spreading width. Seed rate tables calculated at

48", 60" & 72" spread width.

Small Seed Restrictor Plate Restricts distribution rate of smaller seeds and doubles the number of calibration

settings when installed.

Remote Tether Control ON/OFF Control Button, Numeric Seed gate Calibration Settings, and Plus or Minus

Seed Gate Control Function.

Spin Spreader Electrical

Voltage Input 12 volt system with mail power plug for Power Point attachment.

Fuse Rating In line fuse for 15amps maximum.

Start-Up Amps 4 Amp surge for spreading.

Normal Operating Amps .5 Amps for spreading.

Section 5: Features & Benefits

Electric Spin Spreader For utility vehicles with 2" receiver hitch, DH10, DH15 & DH25 Disc Harrows, and FPS48

5/24/16

Table of Contents

Section 5: Features & Benefits

Electric Spin Spreader

Description Benefits

Water Tight Poly Hopper Protects seed and fertilizers from moisture and rodents. Poly construction provides for low

unit weight, quiet operation, and resists corrosion.

Small Seed Restrictor Plate Enables applications of smaller seeds without waste. Doubles the number of possible

application rates over similar competitive models.

Removable and Adjustable

Flinger Ring

Keeps seed or applied products contained to actual width of soil cultivation for reduced

waste. Ring removal enables highly productive wide area broadcast of fertilizer, gypsum,

lime, sand or salt.

Electronic Tether Control Enables easy and convenient control of on/off function and seed gate application rates right

from the seat of the traction unit.

Standard Application Rate

Chart

Enables customers to determine spreader settings with confidence and ease. Similar

competitive models don’t supply rate charts and require costly and wasteful experimentation

to determine proper calibration settings.

Versatile Mounting Systems Provides capabilities for mounting spreaders on a wide range of discs, tractors utility

vehicles, ATVs, and pickups.

12 Volt Operating System Enables attachment to a broad range of lower priced traction units equipped with 12 volt

power outlets.

Low Unit Weight Provides for easy one-person installation and removal

Page is loading ...

Land Pride FPS User manual

Brand: Land Pride

Model: FPS

Category: Spreader

Type: User manual

Download PDF

report

Land Pride FPS User manual

Land Pride FPS User manual

Related papers

Other documents