Stanley SXGP1300XFB Owner's manual

Type
Owner's manual

This manual is also suitable for

EN
IT
BG
CS
DA
DE
PTEL
ES
ET
FI
FR
HR
HU
LT
LV
NL
NO
PL
PT
RO
RU
SK
SL
SV
TR
UK
cod. 94219 - FN
SXGP900XFBE
SXGP1300XFBE
www.stanleytools.eu
SXGP900XFBE
SXGP1300XFBE
TM 5
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
1 SAFETY INSTRUCTIONS
1.1 The appliance you have purchased
is produced by one of Europe's top
manufacturers of household and
gardening pumps. Our appliances
are not designed to withstand the
stresses typical of commercial or
industrial use, or for continuous
duty. You must know and comply
with the instructions provided in this
manual to get the most from your
pump. During connection, use and
servicing of the appliance, take all
possible precautions to protect your
own safety and that of the people
in the immediate vicinity. Read the
safety regulations carefully and
comply with them strictly; failure to
do so may put health and safety at
risk or cause expensive damage.
The manufacturer is not responsible
for any damage caused by incorrect
or improper use.
2 SAFETY DECALS / INFORMATIVE
DECALS
2.1
Comply with the recommendations of
the decals affixed to the appliance.
Check that they are present and
legible; otherwise, fit replacements in
the original positions.
Warning - Danger
Please read these instructions
carefully before use.
Symbol E1.
The appliance must
not be disposed of as household
waste; it may be returned to the dealer
on purchase of a new appliance.
The appliance’s electrical and
electronic parts must not be reused
for improper uses because they
contain substances which constitute
health hazards.
Symbol E3.
Indicates that the
appliance is intended for
household use.
6 7
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
CE Symbol.
Indicates that the
appliance complies with the
relevant EU directives.
ON/OFF switch position
Indicates
the position of the ON/OFF switch.
I = Switch ON
0 = Switch OFF
Guaranteed sound power level
This produce is rated in
insulation class I. This means
that it is equipped with a protective
earthing conductor (only if the symbol
appears on the appliance).
6 7
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
3 SAFETY RULES / RESIDUAL RISKS
3.1 SAFETY PRECAUTIONS: DO NOTS
3.1.1 Injury hazard! DO NOT allow the appliance to be used by children or persons with impaired
physical, sensory or mental capabilities, or who do not have the necessary experience and
knowledge. Children must not use the appliance as a toy. Cleaning and user maintenance must not
be carried out by children.
3.1.2 Explosion or poisoning hazard! Never use the appliance with ammable, toxic or aggressive
liquids, or liquids with characteristics incompatible with its proper operation.
3.1.3 Injury hazard! Do not point the water jet at people or animals.
3.1.4 Electrocution hazard! Do not point the water jet at the appliance, electrical parts or other electrical
devices.
3.1.5 Short-circuit hazard! Do not use the appliance outdoors in the rain. This does not apply to
submersible pumps, which may also be used in the rain; however, it is essential to ensure that the
connections of the plug (A12) and any extension leads used are protected from water splashes and
flooding.
3.1.6 Injury hazard! Do not allow the appliance to be used by children, persons with impaired physical,
sensory or mental capabilities, or any unauthorised persons.
3.1.7 Electrocution hazard! Do not touch the plug (A12) and/or socket with wet hands.
3.1.8 Electrocution and short-circuit hazard! If the power cable (A8) is damaged, it must be replaced
by the manufacturer, one of its authorised Service Centres or similarly qualied persons in order to
prevent all risks.
3.1.9 Explosion hazard! Do not use the appliance if the suction or delivery hose is damaged.
3.1.10 Injury hazard! Place the appliance in a stable position; when using the appliance in the vicinity of
swimming-pools, garden ponds or other outdoor bodies of water, keep it at least 2 m from the water's
edge and protect it from falling into the water or flooding. This does not apply to submersible pumps,
since they can be used immersed in water.
3.1.11 Injury hazard! Check that the appliance is fitted with the data plate which carries its specifications;
contact your dealer at once if it is missing. Appliances without data plate must not be used, since
they cannot be identified and are potentially hazardous.
3.1.12 Explosion hazard! No adjustment of control valves, safety valves or other safety devices, or
tampering with their settings, is permitted.
8 9
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
3.1.13 Scalding hazard! In the event of a pressure switch malfunction or water supply failure, the water left
inside the pump body (A4) may overheat and cause scalding when discharged.
3.1.14 Injury hazard! Do not use the appliance unattended if there is the risk of fouling.
3.1.15 Short-circuit hazard! Do not move the appliance around by pulling the plug (A12), the power cable
(A8) or other connection fixtures; use the handle (A4 b).
3.1.16 Explosion hazard! Do not allow vehicles to drive over the suction or delivery hose. Do not drag or
transport the appliance by the suction or delivery hose.
3.1.17 Injury hazard! Do not use the appliance when people or pets are in the pumped liquid, or may come
into contact with it.
3.2 SAFETY PRECAUTIONS: MUSTS
3.2.1 Short-circuit hazard! All electrical conductors must be protected from splashes of water.
3.2.2 Electrocution hazard! Only connect the appliance to an electrical power source compliant with the
relevant standards (IEC 603641-1); during start-up, the appliance may generate interference on the
electrical system. Only connect the appliance to a socket fitted with a residual current device rated at
30 mA or less. Use only electrical extension leads compliant with the relevant regulations, approved for
outdoor use and with gauge at least equal to that of the appliance's power cable. Power cables wound
onto reels must be completely unwound.
3.2.3 Danger! The appliance must never operate dry; always fill the pump body (A4) with water before
starting it. Even a short period of operation without water may cause damage.
3.2.4 Accidental switch-on hazard! Always disconnect the plug (A12) from the power socket before
carrying out any work on the appliance.
3.2.5 Danger! To guarantee the appliance's safety, the maximum temperature of the pumped liquid must
not exceed 35°C. The ambient temperature must not drop below +5°C.
3.2.6 Danger! The appliance is not designed to pump drinking water or water for human consumption.
The pumped water may be contaminated by lubricant leaks.
3.2.7 Injury hazard! Maintenance and/or repair of the appliance or electrical components must only be
carried out by specialist staff.
3.2.8 Injury hazard! Discharge residual pressure before disconnecting the hose from the appliance; to do
this, disconnect the appliance from the electricity supply and open a user outlet.
3.2.9 Injury hazard! Before use, and at regular intervals, inspect the accessories and check the
appliance's components for signs of failure and/or wear.
8 9
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
4 GENERAL INFORMATION
4.1 Use of the manual
This manual forms an integral part of the appliance and should be kept
for future reference. Please read the manual carefully before installing/
using the appliance. If the appliance is sold, the seller must pass on
this manual to the new owner along with the appliance. Ensure that
every user has access to the manual before the appliance is started
up, and is able to find out about the safety and operating instructions.
4.2 Delivery
The appliance is delivered in a cardboard box.
The supply package is illustrated in fig.1.
4.2.1 Informative material supplied with the appliance
D1 Use and maintenance manual
D2 Safety instructions
D3 Warranty regulations
4.3 Disposing of packaging
The packaging materials are not environmental pollutants but must still
be recycled or disposed of in compliance with the relevant legislation
in the country of use.
5 TECHNICAL INFORMATION
5.1 Intended use
The appliance is designed to pump clean water from wells or rainwater
cisterns for gardening or for use in household water supply systems;
these appliances may not be used for pumping drinking water.
Dirt, sand and sediments are abrasive and damage the impeller.
Fit suitable filters to trap these particles upstream of the pump.
Chemically aggressive substances in the pumped liquid damage the
appliance.
The minimum permitted hourly flow rate is 80 l/h (1.3 l/min).
These appliances are not suitable for drip irrigation systems, since the
water flow rate is too low, meaning that the pumped liquid is unable to
cool the appliance as required.
The appliance must be installed in a dry, well ventilated place,
protected from frost and weather, with an ambient temperature not
exceeding 35°C. It must never be installed or used in the rain, in damp
locations or in wells.
The appliance conforms to the EN 60335-2-41 European standard.
5.2 Improper use
Use by unskilled persons or those who have not read and understood
the instructions in the manual is forbidden.
Supplying the appliance with flammable, explosive, toxic or chemically
aggressive liquids is forbidden.
Use of the appliance in a potentially flammable or explosive
atmosphere is forbidden.
All modifications to the appliance are prohibited. Any modifications
made to the appliance render the warranty null and void and relieve the
manufacturer of all liability under civil and criminal law.
Grinding and polishing substances, or other substances which
attack materials, damage the appliance. These appliances are
not suitable for pumped liquids containing abrasive sand, mud or
clay. These appliances are suitable for pumping water for sanitary
purposes, but not for pumping drinking water!
Faecal substances may not be pumped with these appliances.
5.3 Main components (fig. 1)
A1 Threaded suction fitting
A1b Integral pre-filter (if installed)
A2 Threaded delivery fitting
A2b Filler cap (if installed)
A3 Drain plug
A4 Pump body
A4b Handle
A5 ON/OFF switch
A6 Reinforced hose
A7 Pressure switch
A8 Power cable
A9 Valve
A9b Valve cap
A10 Tank
A11 Pressure gauge
A12 Plug
6 INSTALLATION
Warning - danger!
All installation and assembly operations must be performed with the appliance
disconnected from the mains power supply (fig. 3).
Warning - danger!
Before use, always perform a visual check on the appliance, and especially
the plug (A12) and power cable (A8), for damage. A damaged appliance must
not be used; in the event of damage, have the appliance inspected by the
Service Centre or an authorised electrician.
Warning - danger!
If the power cable (A8) is cut, the warranty becomes null and void and a
replacement genuine power cable (A8) must be installed during the repair,
at the customer's expense (even in case of repair under warranty). If it is
necessary to extend the power cable (A8), only use an extension with gauge
at least equal to that of the original power cable (A8). Never lift the appliance
or remove the plug (A12) from the socket by means of the power cable (A8).
6.1 Assembling the appliance
Before the appliance is put into operation, the suction and delivery
hoses must be connected. Place the appliance in a stable position on
a flat surface, in a location protected from flooding (fig. 4).
To prevent the transmission of vibrations to the pipes or walls, place
the appliance on a rubber mat and use lengths of hose (which must
be resistant to suction and pressure) immediately upstream and
downstream of the appliance (fig. 5) to dampen the vibrations.
6.2 Fitting the suction hose
Warning - danger!
If your device does not have an integral pre-filter, a check valve must be
installed between the suction hose and the suction fitting (A1): this valve
ensures that the suction hose is not pressurised, which could cause leaks
or bursts.
The suction hose conveys the water from the suction point to the
appliance. Connect the suction hose to the threaded fitting (A1).
Check that the suction hose fitted is airtight, since any leaks may
reduce the appliance's flow rate or completely prevent it from drawing
in water. The suction hose must be at least 25 mm (1”) in diameter and
must be resistant to crushing and vacuums.
10 11
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
Use of a suction hose with foot valve is recommended. To ensure
an airtight connection, use Teflon tape (12 - 15 layers) (fig. 6).
Make sure that there is sufficient water in the suction point and that the
hose suction zone is permanently below the water level.
Since the maximum suction lift of self-priming pumps is 8 metres,
the appliance must be no more than 8 m above the water level in
the suction point. The horizontal part of the suction hose must rise
continually from the suction point to the appliance, to prevent the
formation of air bubbles in the hose, which could impair operation of
the appliance (fig. 7).
A pre-filter must be installed between the suction hose and the suction
fitting (A1), unless the appliance has an integral pre-filter (A1 b).
6.3 Filling the appliance
Before fitting the delivery hose, completely fill the pump body (A4) and
the suction hose with water through the delivery fitting (A2). The pump
can also be filled through the filler cap (A2 b), if present (fig. 8).
Bubbles form during filling of the pump body (A4) and must be
discharged by tilting the appliance slightly in various directions.
Fill again and repeat this procedure until the water level is just below
the filling hole.
If the appliance has an integral pre-filter, more water must be added
through the cap of the pre-filter (A1 b). Open the cap, fill with water to
the rim and screw the cap back on by hand (fig. 8).
6.4 Fitting the delivery hose
The delivery hose fitting is on the top of the appliance (A2). The hose
should be connected to a hose or pipe with the largest possible
diameter (at least 19 mm, ¾”). Smaller diameters drastically reduce
the appliance's flow rate. To ensure an airtight connection, use Teflon
tape (12 - 15 layers) (fig. 9).
In a household pumping system, the connected pipes are permanently
pressurised. Therefore, we recommend the use of a reinforced hose,
capable of withstanding this permanent pressure, when connecting to
a permanent distribution system.
Warning - danger!
The use of garden hoses or suction hoses on the appliance's delivery side is
not permitted if the pipes are permanently pressurised, since the continuous
pressure combined with wear and fatigue of the materials may cause them
to burst or tear even after only a short time. Garden hoses may only be used
when not permanently pressurised, e.g. when they are installed downstream
of a stop valve or a water supply tap, and only ever outdoors.
6.5 Safety Measures
The user must prevent damage arising from the flooding of premises
or other causes in the event of a failure of the appliance or external
components by adopting suitable measures (e.g. installation of an
anti-flooding protection circuit, alarm system, backup pump, collection
tank or similar features), which must be connected to a separate,
fail-safe electrical circuit. The safety measures must be suited to the
specific conditions of use and must be able to reduce and/or prevent
the damage caused by water leaks.
The user must also install a spray guard to prevent water leaks or
splashes due to a pump failure from causing damage. A backup pump
or a floor drain must be installed to ensure that any water from leaks
is promptly removed. Otherwise, an alarm system can be installed
to trigger an alarm and/or an emergency shut-down of the appliance
and water supply in the event of a water leak, before damage to the
equipment or property can occur.
We also recommend raising all equipment in appliance installation
rooms about 5-10 cm above the floor so that any water leaks will
not cause immediate damage. The manufacturer accepts no liability
for damage caused by failure to comply with this recommendation.
Warning - danger! Dry operation
If the appliance runs for more than 5 minutes with the water suction point
closed, it may be damaged due to overheating. Switch off the appliance when
the normal water flow is obstructed.
Dry operation will damage the appliance beyond repair, so never allow it to
run dry for more than 10 seconds.
7 ADJUSTMENTS
7.1 Preliminary adjustments
Our appliances are preset in the factory and users must not modify
these settings.
8 START-UP
Warning - danger!
All installation and assembly operations must be performed with the appliance
disconnected from the mains power supply (g. 3).
8.1 Start-up
Once all the pipes have been connected and the pump body (A4) is
full of water, the plug (A12) can be connected and the ON/OFF switch
(A5) turned to ON. During the priming phase, the delivery pipe must
be open to allow the air in the system to escape and to enable the
water pressure to build up. If the suction hose is not completely full
of water, it may take the appliance up to 7 minutes to become fully
operational. If the water has not pressurised after the maximum
priming time stated, switch the appliance off and proceed as described
in the troubleshooting plan (chapter 11).
8.2 Technical information
The appliance's stated ow rate values are maximum values, which
are reduced if external components (e.g. delivery hose, elbows,
pre-lter, etc.) are used. This should be borne in mind when choosing
the appliance. The actual ow rate for specic installation conditions is
stated in the ow rate graph (g. 12).
9 MAINTENANCE
Warning - danger! The system is pressurised!
Before any maintenance procedure and/or during troubleshooting, disconnect
the power cable (A8) from the socket.
Check that the connection hoses or the appliance's tank (A10) are not still
pressurised. To ensure this, turn on a user (water supply tap) and drain all
the water from the system. All maintenance and cleaning work can then be
carried out.
9.1 Cleaning the filters
Clean the pre-lter (A1 b) regularly with clean water and/or inspect it
to ensure that it is not fouled (g. 10). Sluice the lter compartment
with clean water.
10 11
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
9.2 Checking the pressure in the tank (A10)
To ensure that the appliance operates correctly, the pressure in the
tank (A10) must be checked at regular intervals (3-4 times a year); it
must be 1.5 bar. To check the pressure, unscrew the valve cap (A9 b)
on the tank (A10) and check the pressure by connecting an air pump
with pressure gauge to the valve (A9) (g. 11). If the pressure is less
than 1.5 bar, restore it to that value.
Insufcient air pressure causes the appliance to malfunction and leads
to wear of the rubber diaphragm in the tank (A10). Any damage to
the appliance caused by incorrect pressure in the tank (A10) is not
covered by the warranty.
10 STORAGE
Warning - danger! The system is pressurised!
Before any maintenance procedure and/or during troubleshooting, disconnect
the power cable (A8) from the socket.
Check that the connection hoses or the appliance's tank (A10) are not still
pressurised. To ensure this, turn on a user (water supply tap) and drain all
the water from the system. All storage procedures can then be carried out.
It is essential to protect the appliance from frost, and in case of
temperatures of +5°C or below it must be uninstalled and stored in
a dry place, protected from frost. After disconnecting the suction and
delivery hoses, unscrew the drain plug (A3) and tilt the appliance to
drain out all the water in the tank (A10). To empty the pump body (A4)
turn the appliance upside down to drain the water from the delivery
tting (A2).
12 13
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
11 TROUBLESHOOTING
Problems Possible causes Remedies
The motor is running but the
appliance does not suck in water
1) The pump body (A4) was not filled with water before start-up. 1) Fill the pump body (A4, see point 6.3).
2) Suction hose not airtight.
2) Check that the recommended accessories were used. Check that
the suction hose is airtight, use Teflon tape on the threads.
3) Foot valve suction strainer obstructed. 3) Clean foot valve and suction strainer.
4) Delivery side air unable to escape because suction point
is closed.
4) During priming, open the suction points (water supply tap, water
hoses).
5) Not enough time allowed.
5) Completely fill the suction hose with water and wait up to 7
minutes after the appliance is started.
6) Excessive suction lift. 6) Reduce the suction lift (max. 8 m).
7) Suction hose not immersed in water.
7) Check the water level in the well or cistern and lengthen the
suction hose if possible .
Motor does not start 1) No mains power. 1) Check the voltage, connect the plug (A12).
Water flow rate insufficient
1) Suction lift and/or head excessive.
1) Excessive suction lift and head and external components all
reduce the flow rate! This is not a malfunction.
2) Foot valve suction strainer obstructed. 2) Clean the suction strainer.
3) Water level in suction point drops too fast. 3) Immerse the foot valve in a greater depth of water.
4) The appliance's flow rate is being reduced by soil in the water.
4) Clean the pump body (A4) by directing a jet of water in through
the suction fitting (A1) and delivery fitting (A2), and if necessary
have the appliance checked by the Service Centre. Use a pre-filter
if the appliance does not have an integral pre-filter (A1 b).
The thermostat is cutting out the
appliance
1) Motor overloaded due to friction between dirt particles and
impeller.
Dry operation or flow of water insufficient.
1) Clean the inside of the pump body (A4) by directing a jet of water
in through the delivery fitting (A2), leave the thermostat to cool for
about 1 h, and if necessary have the appliance checked by the
Service Centre.
2) Dry operation.
2) Check that there is water present, leave the thermostat to cool
for about 1 h, and if necessary have the appliance checked by the
Service Centre.
The appliance continually switches
on and off
1) No check valve on suction hose, water flowing back from
suction hose.
1) Check whether a foot or intermediate valve is installed on the
suction side.
2) Rubber diaphragm in tank (A10) faulty.
2) Replace the rubber diaphragm or the tank. Contact the Service
Centre.
3) No air pressure in tank.
3) Fill the tank (A10) with air by means of the relative valve (A9) to
a pressure of 1.5 bar (see Maintenance).
4) Delivery side not airtight.
4) Seal the delivery side to render it airtight, check that the system
is airtight.
The appliance operates continually
1) The switch-off pressure set for the pressure switch is too high.
1) Notify the Service Centre and have the switch-off pressure
adjusted.
2) Delivery side not airtight.
2) Seal the delivery side to render it airtight, use Teflon tape on
the threads.
12 13
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
WARRANTY
The warranties relating to the appliances described in this manual are conditional on compliance with all the recommendations it contains, especially those
relating to use, installation and operation.
We grant a warranty of 24 months (12 months for professional sales) from the date of purchase for the product described, covering defects in material or
workmanship in accordance with current legislation. Requests for service under warranty must be accompanied by the original proof of purchase.
The warranty does not cover the costs of dismantling and installing the appliance concerned in the place of use, travel costs to and from the place of use for
repair staff, or transport costs.
Claims arising from incorrect installation or operation, unsuitable conditions of use, negligence, commercial use or inappropriate repair attempts are not covered
by the warranty and no responsibility is accepted for them; normal wear and tear is also excluded.
The resulting costs, and especially inspection and transport costs, will be charged to the sender and/or the appliance's operator. This also applies, in particular,
when a warranty request is submitted but the appliance is found to be operating perfectly with no defects, or the problem is not due to defects in materials or
workmanship.
Before return to the user, every product undergoes strict technical inspection. Repairs under warranty must only be performed by one of our Service Centres or
an authorised repair workshop. Attempted repairs by the customer or unauthorised third parties during the warranty period will result in the loss of all warranty
entitlement.
Cutting off the power plug and/or shortening the power cable result in loss of warranty entitlement.
Work done by us under warranty does not extend the duration of the warranty, or give rise to a new warranty period for the parts replaced or repaired.
All further entitlement, including the right to discounts, changes or compensation, or consequent damage of any kind, is excluded.
In the event of malfunction, contact the point of sale where the product was purchased, showing proof of purchase.
14 TM
(Translation of the original instructions)
© 2017 English
(Translation of the original instructions)
© 2017 English
EN
EN
Technical Data Unit SXGP900XFBE SXGP1300XFBE
Voltage V/Hz
230 V ~ 50 Hz 230 V ~ 50 Hz
Power W 900 1300
Max. head (H
max
) m
42 50
Max. ow rate (Q
max
) l/h
3300 4200
Working pressure bar
1.5~3.0 1.5~3.0
Max. water temperature (T
max
) °C
35 35
Max. suction lift m
8 8
Max. particle size Ø mm
0 0
Protection class
-
Motor insulation -
Class B Class B
Motor protection - IPX4 IPX4
Sound power level L
WA
(EN ISO 3744) dB (A)
80 83
Net weight kg
15.3 16.2
Gross weight
kg 16.6 17.2
Fitting diameter mm
25.4 25.4
Cable length m
1 1
Tank volume l
24 24
Subject to technical modication!
275
© 2017
Belgique et Luxemburg E. Walschaertstraat 14 www.stanleyworks.be
België en Luxembourg 2800 Mechelen Enduser[email protected]
Belgium BE-NL= +32 15 47 37 63
BE-FR = +32 15 47 37 64
BE Fax: +32 15 47 37 100
Danmark Roskildevej 22 www.stanleyworks.dk
2620 Albertslund [email protected]
Fax: 70224910
Deutschland Richard Klinger Str. 11 www.stanleyworks.de
65510 Idstein info@sbdinc.de
Tel: 06126-21-1
Fax: 06126-21-2770
Ελλάς Hμερος Τόπος 2 - Χάνι Αδάμ www.stanley.gr
Ασπρόπυργος -19300 -Αττική [email protected]
Τηλ: +30 210 8985208
Φαξ: +30 210 5597598
España Parque de Negocios “Mas Blau” www.stanleyworks.es
Edificio Muntadas, c/Bergadá, 1, Of. A6 [email protected]
08820 El Prat de Llobregat (Barcelona) Tel: 934 797 400
Fax: 934 797 419
France 5, allée des hêtres www.stanleyoutillage.fr
BP 30084, 69579 Limonest Cedex [email protected]
Tel: 04 72 20 39 77
Fax: 04 72 20 39 00
Schweiz In der Luberzen 42 www.stanleyworks.ch
Suisse 8902 Urdorf [email protected]
Svizzera Tel: 044 - 755 60 70
Fax: 044 - 730 70 67
Ireland 210 Bath Road; Slough, Berks SL1 3YD UK www.stanleytools.co.uk
Tel: +44 (0)1753 511234
Fax: +44 (0)1753 512365
Italia Energypark–Building 03 sud, Via Energy Park 6 www.stanley.it
20871 Vimercate (MB) Tel. 039-9590-200
Fax 039-9590-313
Nederlands Stanley Black & Decker Netherlands B.V. www.stanleyworks.nl
Postbus 83 Enduser[email protected]
6120 AD Born Tel : +31 164 28 30 63
NL Fax: +31 164 28 32 00
Norge Postboks 4613, Nydalen www.stanleyworks.no
Fax: 45 25 08 00
STANLEY Service Addresses & Contact Details
276
© 2017
Österreich Oberlaaerstrasse 248 www.stanleyworks.de
A-1230 Wien [email protected]
Tel: 01 - 66116 - 0
Fax: 01 - 66116 - 14
Portugal Quinta da Fonte - Edifício Q55 D. Diniz www.stanleyworks.pt
Rua dos Malhões, 2 e 2A - Piso 2 Esquerdo [email protected]
2770 - 071 Paço de Arcos Tel: 214 66 75 00
Fax: 214 66 75 75
Suomi PL 47 www.stanleyworks.fi
00521 Helsinki customerservice.fi@sbdinc.com
Puh: 010 400 4333
Sverige Box 94 www.stanleyworks.se
431 22 Mölndal [email protected]
Fax: 31 68 60 08
United 210 Bath Road; Slough, Berks SL1 3YD www.stanleytools.co.uk
Kingdom Tel: +44 (0)1753 511234
Fax: +44 (0)1753 512365
Hungary Rotel Kft. www.stanleyworks.hu
1163 Budapest,Thököly út 17. Tel +36 1 404-0014
Fax+36 1 403-2260
Czech Republic BAND SERVIS CZ s.r.o. www.stanleyworks.cz
K Pasekam 4440 http://www.bandservis.cz
760 01 Zlín, Czech Republic Tel.: +420 577 008 550
Fax.: +420 577 008 559
Slovakia BAND SERVIS s.r.o. www.bandservis.sk
Paulinska 22 Tel.: +421 335 511 063
917 01 Trnava, Slovakia Fax.: +421 335 512 624
Poland Erpatech www.stanleyworks.pl
ul. Bakaliowa 26 Tel.: +48 22 431 05 00
05-080 Mościska Fax.: +48 22 468 87 35
Slovenia G-M&M d.o.o. www.g-mm.si
1290 Grosuplje T: +386 01 78 66 500
Slovenija F: +386 01 78 63 023
Cyprus IOANNOU J. [email protected]
14A Ath.Diakou street Τel : +357 22344302
1046- Nicosia -Cyprus Fax : +357 22348098
is a registred trademark of The Stanley Black & Decker Corporation used under license.
The product is manufactured and distributed by:
Annovi Reverberi S.p.A. Via M.L. King, 3 - 41122 Modena (Italy).
All the rights reserved.
© 2017 Stanley Black & Decker Corporation
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278

Stanley SXGP1300XFB Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI