Micro Innovations IC710C User manual
- Category
- Webcams
- Type
- User manual
Additional package contents:
Quick Installation Guide
User Manual
Warranty
Installation CD
2.0 MP Webcam (IC710C)
User Manual
2.0 MP Webcam (IC710C)
Page 1
Contents
Verifying system requirements
Identifying webcam features
Installing your new webcam
Installing PhotoImpression software
Capturing video from your webcam
Capturing a photograph from your webcam
FCC compliance statement
Maintaining your webcam
2
2
3
4
5
6
7
8
USB cable
Webcam
IC710C_um.indd 1 4/15/2008 11:12:55 AM
Verifying system requirements
2.0 MP Webcam (IC710C)
Page 2
2.0 MP Webcam (IC710C)
To use the webcam software, you will need:
A computer with an available USB port and CD drive
At least 256 MB RAM
At least 500 MB available hard disk space
Windows compatible sound card and speakers
Windows® XP SP2 or Vista™
If your system uses Windows
XP Service Pack 1 (SP1), please
update to Windows XP Service
Pack 2 (SP2). The update is free at
www.microsoft.com.
To determine which Service Pack
you currently have, right-click
on My Computer and select
Properties.
Under the General tab you will
see the System information.
2
4
3
1
Identifying webcam features
Lens
1
Microphone
2
Ball Joint
3
Foot
4
IC710C_um.indd 2 4/15/2008 11:12:56 AM
Connect the USB cable to an
available USB port on your
computer.
USB ports may be located
anywhere.
Mount the webcam on your
monitor or desk.
Unfold the foot to better grip a
thin monitor.
Rotate the ball joint to adjust
the angle of view.
Insert the CD into your
CD drive and follow the
instructions on the screen.
If the install screen does not
launch automatically, open the
folders on the CD and double-
click the setup.exe file.
2.0 MP Webcam (IC710C)
2
3
1
2.0 MP Webcam (IC710C)
Page 3
Installing your new webcam
IC710C_um.indd 3 4/15/2008 11:12:56 AM
Installing PhotoImpression software
2.0 MP Webcam (IC710C)
Page 4
The InstallShield®
Wizard will guide you
through the installation
process.
2.0 MP Webcam (IC710C)
1
Follow the same
procedure to install
the VideoImpression
software.
There is no need to
restart your computer
after installing this
software.
2
IC710C_um.indd 4 4/15/2008 11:12:56 AM
2.0 MP Webcam (IC710C)
2.0 MP Webcam (IC710C)
Page 5
Capturing video from your webcam
Launch VideoImpression.
Click on the Create a New
Video button.
1
Click on the Capture From
Device button.
2
Click the red Record button to start
capturing the video. A separate
window will appear where you enter
a file name and select options. The
video file is saved to the My Videos
folder as an .avi file.
3
Click the Done button to return to
the VideoImpression home screen.
4
IC710C_um.indd 5 4/15/2008 11:12:56 AM
2.0 MP Webcam (IC710C)
Page 6
Capturing a photograph from your webcam
2.0 MP Webcam (IC710C)
Capturing video from your webcam (cont’d)
Click the Camera button to reopen
the video capture screen to record
another video.
5
Launch PhotoImpression.
Click on the Video button in the
“Get photo from...” dialog box.
1
When the “Capture Image from
Video” dialog box appears, click the
Live button to see the webcam view.
2
Click the Capture button to take a
photograph. The image is saved to
the My Pictures folder as a .jpeg file.
3
Click the Done button to return to
the PhotoImpression home screen.
4
Both software packages include Help
for further information. Click on the
Help menu and select Help or
press F1.
5
IC710C_um.indd 6 4/15/2008 11:12:57 AM
2.0 MP Webcam (IC710C)
Page 7
FCC Compliance Statement IC710C
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction guide, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult a service representative for help.
Properly shielded and grounded cables and connectors must be used in order
to comply with FCC emission limits. Micro Innovations is not responsible for any
radio or television interference caused by using other than recommended cables
and connectors or by unauthorized changes or modifications to this equipment.
Unauthorized changes or modifications could void the user’s authority to operate the
equipment.
Responsible party:
Micro Innovations Corp.
1090 King Georges Post Road, Suite 104
Edison, NJ 08837
Telephone: 1(732) 486-0079
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de classe B est conforme à la norme NMB-003 du Canada.
Tested To Comply With FCC Standards
FOR HOME OR OFFICE USE
IC710C_um.indd 7 4/15/2008 11:12:57 AM
For assistance, visit www.microinv.com or call toll free: 1-877-550-5534
Technical support hours: Monday - Friday 8:30am to 7:00pm EST.
The Windows® name and logo are registered trademarks
of Microsoft Corporation.
All brand and product names are trademarks or registered
trademarks of their respective companies.
© 2008 Micro Innovations Corp.
2.0 MP Webcam (IC710C)
Page 8
Regular maintenance ensures a longer product life and minimizes the
chance of causing damage to your webcam.
Always disconnect the webcam before cleaning it.
Clean the lens with a lint-free cloth.
Do not try to repair any part of this product. Only Micro Innovations
Corp may service or repair its products.
Maintaining your webcam
IC710C_um.indd 8 4/15/2008 11:12:57 AM
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Micro Innovations IC710C User manual
- Category
- Webcams
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Micro Innovations USB50BT User manual
-
-
-
-
-
-
-
-
-