EcoNet EZW1204 is a Z-Wave leak sensor that will help you prevent water damage in your home. It can be placed on the floor or mounted on the wall, and it will send a notification to your compatible Smart Home Controller when it detects water.
Some of the features of the EZW1204 include
- 3 x gold spring probes to detect water
- Snap-in base for wall mounting
- Wired plug-in leak sensor
- 3 x LED status indicators
- Lever switch for inclusion/exclusion
- Battery life of 3+ years with alkaline batteries (lithium batteries recommended for longer life)
- Z-Wave Plus, 908MHz
- Wireless range of 30M (line of sight)
EcoNet EZW1204 is a Z-Wave leak sensor that will help you prevent water damage in your home. It can be placed on the floor or mounted on the wall, and it will send a notification to your compatible Smart Home Controller when it detects water.
Some of the features of the EZW1204 include
- 3 x gold spring probes to detect water
- Snap-in base for wall mounting
- Wired plug-in leak sensor
- 3 x LED status indicators
- Lever switch for inclusion/exclusion
- Battery life of 3+ years with alkaline batteries (lithium batteries recommended for longer life)
- Z-Wave Plus, 908MHz
- Wireless range of 30M (line of sight)
EZW1204 Quick Start Guide
• The EZW1204 Z-Wave Leak Sensor requires 3 x AA batteries. Depending on controller and leak configuration, a standard set of alkaline
batteries should last 3+ years. We recommend lithium batteries for a longer battery life.
• The EZW1204 can be wall mounted using the snap-in base with wired leak sensor or it can be placed on the floor in sensitive areas.
Sensitive Leak Locations:
• Laundry Room Floor
• Floor by hot water tank
• Below Dishwasher
• Bathroom/s behind toilet (wall mount configuration)
• Floor behind fridge with ice maker/water
• Under kitchen sink (wall mount configuration)
• Sump pump (wall mount configuration
Caution: If you do not have experience installing
and configuring EZW1204 type of devices, please
consult a professional installer.
Specifications:
• Model: EZW1204 (U.S.)
• 3 x AAA Batteries required
• Z-Wave Plus, 908MHz
• Wireless Range: 30M (line of sight)
• Leak Sensor with 3 x gold spring probes
• Snap-In base for wall mounting
• Wired Plug In Leak Sensor
• 3 x LED Status Indicators
• Lever switch for inclusion/exclusion
Floor Mounting:
Select a clean area that is likely to pool water in the case of a leak. Place the EZW1204 (without wall mount base) on the floor or surface in this leak
sensitive area. The surface should be flat so that EZW1204 is resting with all three spring loaded pins touching the floor or flat surface. The wall
mount kit should be use for the installation in areas where the sensor might be disturbed or move by a pet or person.
Wall Mounting:
The wall mount bracket can be mounted using the double-sided tape or an appropriate wall screw. (screw not included) Plug the wired sensor into
the wall bracket and check positioning and distances for both the wall bracket and the water sensor disc and mark positions. Mount the wall
bracket (wired plug at 180 degrees pointing down). Mount the sensor disc using double-sided tape so that it is in an ideal position to sense water.
Snap the EZW1204 into the wall bracket and test by wetting the sensor disc with a wet cloth. The EZW1204 must be positioned in the wall bracket
properly for the disc sensor to work.
Installing Batteries:
Counter Clockwise with a small twist open the EZW1204 to expose circuit board, LED x3, switch and battery holder.
Install the 2 x AAA batteries and leave the cover for access to the pairing/inclusion switch.
Inclusion/pairing switch
Pairing the EZW1204 Leak Sensor with a Z-Wave Controller
Including or Pairing the EZW1204 to a Z-Wave Controller: Place the Z-Wave controller in pairing (learning) mode (Consult your controller
manual/user guide). Bring the EZW1204 close to your controller, within several feet and press inclusion switch 3 or more times rapidly (within
0.5 seconds). Once the controller has acknowledged the inclusion, the EZW1204 has been included in the Z-Wave network with the controller.
Exit the pairing mode in your controller and you should see the EZW1204 leak sensor in your list of devices. Depending on your Smart Home
Controller type and setup, the EZW1204 may appear as a leak sensor, a switch or a door/window sensor. Some devices (like the Vera
controller) require that you reload or refresh the controller so it polls, identifies, and configures the new device. Once the configuration is
complete, you can add the EZW1204 Leak Senor into your Smart Home automation for notification and activation of other devices such as the
EcoNet Valve Robot to shut off the water. Once in position, when the leak sensor probes, either on the bottom or on the wired disc probe, get
wet, it will send a “leak message” to your compatible Smart Home Controller.
Excluding or Un-Pairing the EZW1204 from a Z-Wave Controller: Place your Z-Wave controller in exclusion (un-learning) mode. Once the
controller is in exclusion mode, bring the EZW1204 close to the Z-Wave controller (several feet) and press the Power button 3 or more times
rapidly (within 0.5 seconds). Once the controller has acknowledged the exclusion, the EZW1204 has been cleared of any previous
inclusions/pairings. (It is recommended to keep the EZW1204 within 1M/3ft of the controller when pairing or un-pairing)
There can be a number of reasons that the EZW1204 does not work with your controller. If the inclusion process does not work the first time,
repeat the process but try “excluding” first and then complete the “inclusion” process.
If you have any questions or if you are experiencing any issues with the EZW1204,
please contact EcoNet Controls Support via email at [email protected]
For more details, please visit www.EcoNetControls.com.
Z-Wave Network inclusion
Press the Power button 3 or more times rapidly (within 0.5 seconds). It
is recommended to keep the EZW1204 within 1M/3ft of the controller.
(Set controller to inclusion mode first)
Z-Wave Network exclusion
Power the button 3 or more times rapidly (within 0.5 seconds). It is
recommended to keep the EZW1204 within 1M/3ft of the controller.
(Set controller to inclusion mode first)
Device Reset
Press and hold the switch down for 5 seconds.
Note: This should only be used in the event your networks primary
controller is missing or otherwise inoperable
Association capabilities
Group 1: Lifeline
Group 2: Water Leak send basic set
Group 3: Cover plate open send basic set
Wake Up
Default wake up time is 4 hours
(some controllers/gateway will set)
Water Leak Report:
Sensor Binary report:
Notification Report:
Battery Report:
Water no Leakage Report:
Basic set:
Sensor Binary Report:
Notification Report:
Battery Report:
Sensor Valve Detected an event =FF, Sensor Type Water=06
Notification Type Water = 05, Event 02
Battery Level xx
Value 00
Sensor Value ide = 00, Sensor Type Water = 06
Notification Type Water = 05, Event 00
Battery Level xx
Generic Device Class:
Specific Device Class:
Command Classes:
07 – GENERIC_TYPE_SENSOR_NOTIFICATION
01 – SPECIFIC_TYPE_NOTIFICATION_SENSOR
5E - COMMAND_CLASS_ZWAVEPLUS_INFO
86 - COMMAND_CLASS_VERSION
72 - COMMAND_CLASS_MANUFACTURE_SPECIFIC
5A - COMMAND_CLASS_DEVICE_RESET_LOCALLY
73 - COMMAND_CLASS_POWERLEVEL
80 - COMMAND_CLASS_BATTERY
85 - COMMAND_CLASS_ASSOCIATION
59 - COMMAND_CLASS_ASSOCIATION_GROUP_INFO
71 - COMMAND_CLASS_ALARM
30 - COMMAND_CLASS_SENSOR_BINARY
84 - COMMAND_CLASS_WAKE_UP
7A - COMMAND_CLASS_FIRMWARE_UPDATE_MD
-
1
-
2
-
3
-
4
EcoNet EZW1204 is a Z-Wave leak sensor that will help you prevent water damage in your home. It can be placed on the floor or mounted on the wall, and it will send a notification to your compatible Smart Home Controller when it detects water.
Some of the features of the EZW1204 include
- 3 x gold spring probes to detect water
- Snap-in base for wall mounting
- Wired plug-in leak sensor
- 3 x LED status indicators
- Lever switch for inclusion/exclusion
- Battery life of 3+ years with alkaline batteries (lithium batteries recommended for longer life)
- Z-Wave Plus, 908MHz
- Wireless range of 30M (line of sight)
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
EcoNet Controls EBV105 User manual
-
Z-Wave EcoNet Controls EBV105 Water Valve Quick start guide
-
Elexa DMWS1 User manual
-
Panasonic KXHNS103FX Operating instructions
-
AirLive Smoke Sensor User manual
-
HomeSeer HS-LS100+ User manual
-
Eedomus eedomus+ User manual
-
Elexa DMMS1 User guide
-
Elexa Consumer Products Guardian Bridge GBR1 User manual
-
